Search Documents

By Duane A. Smith

Introduction From the days of the Spanish in the eighteenth century, Colorado's San Juan mining district has attracted miners and public interest. The Spanish left behind names - San Juans, La Plata, Animas, legends of lost mines, and the remains of a few scattered mining operations. They came, but did not stay. Again in 1860-61, as a spinoff of the Pike's Peak gold rush, prospectors climbed the mountains and descended into the canyons searching for gold. They found some, not enough to convince them to remain and confront the isolation, often hostile environment and the Utes, who rightfully felt this to be their home. Not until the 1870s did miners come to stay. In their wake little camps grew in the high valleys and squeezed into narrow canyons. Nowhere else in Colorado were there more rugged mountains, a higher average elevation, nor a climate that one old Swede said was "three months of mighty late fall and nine months of winter." The San Juans proved eventually to be a mineral treasure chest. At the moment, however, the prospectors sought gold. Then they discovered silver deposits and the first rush was on. It got started just in time to be completely overcome by the Leadville excitement. At Leadville, investors almost fell over themselves to buy claims and stock in the hopes of becoming another millionaire like Leadville's own Horace Tabor. The San Juaners could only look from the sidelines and speculate how it might have been had fate been kinder. Fate was seldom kind, as these pioneers quickly discovered. From the mid-1870s on, the San Juaners wrestled with some major problems. And the fate of their district rode in the balance. The problems they faced were similar to those of other Colorado districts, compounded by their geographic isolation. Every mining district needed the best transportation system available, experienced investors combined with sound investment, and mineral reserves to develop. The San Juans offered the last in abundance. It was hoped the first two would appear. Railroads - much needed transportation link Nothing was more desired than railroad connections, the penultimate nineteenth century form of transportation. Colorado's own, the Denver & Rio Grande, resolved the issue with its mountain-hugging narrow gauge. As early as the mid-1870s, the D&RG dreamed of tapping this potentially lucrative market in southwestern Colorado. A national economic depression and then the Leadville silver excitement prevented immediate construction. Not until 1879-80 did survey crews start work.

Jan 2, 1988

By Neal Retzer, Adam Bedell, Nick Cioffredi

The first wagon trail across Loveland Pass was built in 1869 thus starting the struggle between the Colorado Rockies and interstate travel. The 1st Pioneer Bore underneath Loveland Pass at the Continental Divide in Colorado was attempted between 1941 and 1943 and was abandoned due to ground conditions at the Loveland Fault. Construction on the nearby Eisenhower Tunnel began in 1967 and was completed in 1973. Numerous challenges associated with tunneling, including at 11,000 ft were overcome. The purpose of this paper is to summarize the history of investigation and construction challenges associated with the Eisenhower Tunnel to celebrate its 50th anniversary.

Jun 13, 2023

By Edmund H. Warner

Any city dweller who has walked alone along a remote mine passageway has to be impressed by the eerie silence - the total absence of noise except for ones own breathing and scuffing of boots on the bottom. An underground mine can have tremendous contrasts, from complete silence to the ear piercing clatter of percussion drills working on the mine roof. Noise in underground mining machines is both useful and detrimental. Without characteristic noises that are recognizable to miners, operators would have a more difficult job operating their machines. Noise serves as a warning of approaching machinery, and changes in noise give indication that breakdowns may occur. But excessive noise is a health hazard. In recognition of this fact, our Congress included noise exposure as a part of the "Coal Mine Health and Safety Act of 1969". As Fig. 1 indicates, allowable noise exposure is established by specifying a time duration permitted at different noise levels. This is the well known "Walsh-Healey" criteria which governs noise exposure in many industries.

Jan 1, 1977

By Chee S. Theng

As the 2016 president of the Society for Mining, Metallurgy & Exploration Inc., I am pleased to present the 2016 issue of the Transactions of the Society for Mining, Metallurgy & Exploration Inc., Vol. 340. A significant portion of the contribution that we make as a professional society is the publication of professional and technical papers that accelerate the advancement of scientific knowledge and enable the transfer of technology. Communication within the mining community is the key to a successful society. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, PA, that resulted in the founding of the American Institute of Mining, Metallurgical and Petroleum Engineers (AIME). Those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume fulfills that pledge. The 2016 Transactions contains some of the most interesting research and insights from the past year and features an international slate of authors spanning industry, academia and government. Papers include the latest findings from the U.S. National Institute for Occupational Safety and Health (NIOSH) and special-issue articles on process development testing. The 2016 Transactions consists of a total of 65 technical papers, encompassing all 21 papers published in 2016 in the Technical Papers Section of Mining Engineering (Vol. 68) and all 27 papers published in 2016 in Minerals & Metallurgical Processing (Vol. 33). Additionally, this volume contains 17 papers that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. All of the technical papers were peer-reviewed. The process of review and publication requires much hard work by authors, reviewers and our publications staff. As the 2016 president of SME and on behalf of all our members, I would like to extend our gratitude to all whose volunteer efforts contributed to the publication of this volume.

Jan 1, 2016

By Shaojun Bai

Siderite ore with high phosphorus content was reduced isothermally at 1,050° C with pulverized coal and different dosages of sodium carbonate. X-ray diffraction (XRD), scanning electron microscopy (SEM) and energydispersive analysis of X-rays (EDAX) were used to characterize the samples. The influence of sodium carbonate on the carbothermic reduction process was investigated. Sodium carbonate and its dosage played a considerable role in the carbothermic reduction. The iron particle size in the reduced ore was below 20 µm, and fayalite was abundant without sodium carbonate additive. With a mass ratio of Na2CO3-to-ore of 5% additive, the iron particle size in the reduced ore was generally above 50 µm, and the diffraction intensity associated with metallic iron in the XRD pattern increased. The effect of sodium carbonate on the phase transformation of fluorapatite during carbothermic reduction was also addressed via thermodynamic calculations and aqueous leaching experiments. The results showed that the fluorapatite was not reduced to P2 at 1,050° C, and a portion of the fluorapatite was converted to soluble phosphate. The reduction of siderite can be catalyzed by adding an appropriate amount of sodium carbonate. This catalytic activity was caused by an increase in the reducing reaction activity of FeO and the acceleration of the carbon gasification reactions. The decrease in phosphorous content in the iron concentrate was attributed to an improvement in the separation of the iron phase from the slag phase when sodium carbonate was added and with the formation of soluble phosphate.

By Joseph W. Murray

Prior to 1950 Magma's ore production came from two parallel, steeply dipping, east-west striking mineralized faults, one called the Main or Magma vein, and the other the Koerner vein, which lay about 1100 feet to the south, This vein system has been explored and mined over 9000 feet horizontally and 4800 vertically. In 1950 continued exploration led to the discovery and subsequent development of replacement ore bodies in the Devonian limestone zones adjacent to the veins. These replacement deposits occur in the eastern part of the Magma Mine, and follow the strike and the 30" east dip of the host limestone. Strike length of the ore bodies varies from 250 to 500 ft., and thickness from 15 to 125 ft. The ore bodies are large tabular masses with chalcopyrite and bornite being the dominant ore minerals. Hematite and pyrite are the most abundant gangue minerals. Incompetent limestone, shale, or a porphyry sill hanging wall is charactertistic of substantial portions of the replacement beds. In many instances the ore itself is blocky, badly fractured, and intermixed with layers of limestone gouge, pyrite and hematite.

Jan 1, 1973

By Mehdi Noori, Atefeh Azizitorghabeh, Fereshteh Rashchi, Ataollah Babakhani, Sarah Mahmoudi

The focus of this research was to evaluate the synergistic effect of bis(2,4,4-trimethylpentyl) phosphinic acid (CYANEX 272) and di-(2-ethylhexyl) phosphoric acid (D2EHPA), diluted in kerosene, on the extraction and separation of Co(II) and Li(I) from synthetic sulfate solution. The results indicated that using a mixture of CYANEX 272 and D2EHPA was efficient in extracting and separating Co(II) from Li(I). The optimum ratio of CYANEX 272/D2EHPA was found to be 5:1, in which the highest separation factor was obtained (5973.23), and ΔpH0.5 was 4.10. Adding tributyl phosphate (TBP) as a modifier and increasing the temperature improved the metals’ separation rate and extraction efficiency. Thermodynamic studies were also carried out, and ΔH, ΔS, and ΔG values were computed, revealing the endothermic nature of Co(II) and Li(I) extraction by CYANEX 272/D2EHPA mixture. The conducted experiments for the McCabe–Thiele diagram showed the possibility of using two stages to extract over 99% of Co(II) and Li(I). Slope analysis and Fourier transform infrared spectroscopy (FT-IR) were employed to comprehend the Co(II) and Li(I) extraction mechanism using a mixture of CYANEX 272 and D2EHPA.

Jan 17, 2022

By Robert D. Coale

This paper will describe the copper concentrate slurry pipeline and pumping system between the concentrator and the port at Bougainville Copper Ltd. The operations of Bougainville Copper Ltd. are located on the island of Bougainville in the South Pacific. Geographically, it is the northernmost island of the Solomon Group but, politically, it is part of Papua New Guinea. Papua New Guinea is a United Nations Trust territory administered by Australia, having recently been given self-government, with independence scheduled for December 1974. (Fig. 1). The island is approximately 130 miles long by 30 miles wide, with the Crown Prince mountain range forming a spine along its length. The mountains in place are over 8,000 feet high with the mine located on the western flank at an elevation of 2,200 feet. Exploration on Bougainville for copper by Conzinc Riotinto of Australia (CRA) began in 1963 and by 1968, through geophysical, geochemical and diamond drilling methods, an orebody containing nearly one billion tons of ore grading approximately 0.48% Cu. and sane gold had been outlined. Bougainville Copper Ltd., the company operating the mine, is 53.6% wined by CRA, 20% mined by the government of Papua New Guinea with the public Folding the remainder of the shares. The first copper concentrate was produced in early 1972, with production for the first full year, 1973 being:

Jan 1, 1974

By Jr. Wilkinson

Mine planners are under pressure to evaluate the impact of changing economic times and newly acquired data on the mine plan. Incorporating change, such as commodity prices, customer sales, changing cost assumptions, and newly acquired geologic data into the mine plans requires quick turn-around for model building and planning to keep the mine plan on pace with changes as they are occurring. Because of the length of time required to perform some of the geologic modeling and mine planning tasks, planning frequency may not be keeping pace with the frequency of change. This paper discusses how one company has increased the frequency rate and accuracy of mine plans to keep current with incoming data, ensuring mine plans reflect the latest information, thereby minimizing or eliminating production cost variance.

Jan 1, 2010

By A. G. Mayton, D. H. Ambrose, C. C. Jobes, N. K. Kittusamy

In a systematic study, the National Institute for Occupational Safety and Health (NIOSH) evaluated seat designs in low- and mid-seam shuttle cars during production operations at two underground coal mines in southern West Virginia. The purpose was to support, with additional data, earlier findings that NIOSH ergonomic seat designs (featuring viscoelastic foam padding and lower-back support) may help reduce health risks to operators of coal mine shuttle cars. Eight shuttle car operators evaluated seven seat designs (one already in use in each vehicle and five NIOSH designs) relative to perceived and measured whole-body vibration (WBV) exposure (including vehicle jarring/jolting) and discomfort. Operators’ perceptions using a visual analog scale (VAS) and questionnaire ratings were compared with International Standards Organization (ISO) 2631-1:1985 fatigue-decreased proficiency (FDP) limits and measured WBV levels on low- and mid-seam shuttle cars. Objective and subjective data results indicated that NIOSH seat designs (with added adjustability, lower-back support and improved seat padding) performed better to reduce vehicle jarring/jolting levels and that shuttle car operators favored them over existing seat designs. The NIOSH low- and mid-seam shuttle car seats showed 45 to 77 percent better performance in FDP and 9 to 60 percent better performance overall in operators’ ratings. Considering the VAS results for low- and mid-seam shuttle cars under no-load conditions, operators rated the level of jarring/jolting 18 to 89 percent lower with the NIOSH seats. Reductions in measured vehicle jarring/jolting were 19 to 46 percent for the three-directional vector sum accelerations relative to the existing seats on the low- and mid-seam shuttle cars. Questionnaire responses indicated that operators for both shuttle car models rated NIOSH seat designs as more comfortable overall. Vehicle operators most frequently suggested adding armrests to improve the seats on the mid-seam shuttle car. A suggested improvement for the low-seam shuttle car was to make the seat a better fit for the operator compartment, which would enhance clearance between the operator and vehicle controls and allow for better seat adjustment and operator visibility.

Jan 1, 2009

By Osvaldo A. Bascur

Standards and Technology for bringing information at the desktop has greatly evolved in recent years. The benefits to be realized depend on how these new tools are embraced at the performer level. A key operating challenge is to ensure collective effort is geared towards the most efficient achievement of identified operating and corporate objectives. Presentation, application and data repository modular software are emerging in successful client server applications. The industrial desktop emerges as the new tool for continuous improvement and innovation in industrial operations. Here, process information, reliability maintenance, process simulation, production schedules, performance monitoring are integrated using Microsoft enabling tools at the desktop. A workflow model is presented to assist in implementing a strategic information system in metallurgical plants.

Jan 1, 1996

By Jameel Menashi

Aqueous solutions of Na2Cr04 can be reduced with CO to produce hydrous Cr203 and NaHCO3/Na2CO3. CH3OH, HCOO and HCHO in the presence of CO2 also reduce Cr 6+ and yield similar products. It is shown that the rate of Cr6+ reduction can be represented by the expression -d[Cr6+]/dt=k[Cr6+)1/2[R] where [R] is the aqueous phase concentration of CH3OH, HCOO- or CO. With these three reductants, the activation energies for the reduction processes are comparable and are of the order of 100 kJ/mole. Rapid reduction rates are attained at temperatures in excess of 220°C and, with these three reductants, a green acid-insoluble readily filterable hydrous Cr203 is formed. With HCHO significant reduction of Cr6+ occurs at about 80-100°C and an acid-soluble violet modification of hydrous Cr2O3 is formed. The reduction process is reasonably selective: solutions of Na2CrO4 contaminated with Mo6+ and W6+ can be reduced to yield a Cr2O3 product with significantly reduced contaminant levels. These findings are utilized as a basis for a process for recovering chromium from secondary source materials.

Jan 1, 1984

By Giovanni Barla

The stress-relief method for the determination of the ground stress tensor is a common procedure in rock mechanics. In particular, the method of applying gauges to the end of a borehole is a well-established technique. Investigations, both experimental and theoretical, indicate that large discrepancies can exist in the determination of the ground stress tensor when the rock substance is not the ideal elastically isotropic material assumed for the reduction of data. The purpose of this paper is to extend the analysis of strain gauges applied to the end of a borehole to rock material more closely approximate to an orthotropic substance.

Jan 1, 1969

By Jaeheon Lee, Junmo Ahn, Jae-Yeon Kim, Yoo-Jin Kim, Jiajia Wu, Eun-Woo Kim, Jai-Won Byeon, Jun-Jae Lee

The surge in demand for battery materials, coupled with environmental challenges linked to battery disposal, underscores the need to recycle spent lithium-ion batteries (LIBs). Green recycling approaches, in particular, have garnered attention for battery recycling. In this study, a hydrometallurgical method using a synergetic organic lixiviant combining methanesulfonic acid (MSA) and citric acid (CA) as an alternative to inorganic mineral acids was introduced as a green approach to recycle cathode materials of LIBs. The conditions for leaching and recovery processes were optimized. Cathode materials were regenerated using the recovered materials. Moreover, the leaching performance and economic feasibility of this leaching system were compared with those of various other organic acids.

Feb 1, 2024

By D. O. Miller

The effective staffing of personnel in a new concentrator facility is a key factor in the success of the operation. By selectively recruiting quality individuals, a company is in a strong position to build a positive work ethic which will become an integral part of it's culture. And culture, which is a set of standards that all employees work to uphold, is that intangible as- set that often determines whether or not a company will survive during difficult economic times. Recruiting and placement of personnel in a concentrator facility requires an emphasis on planning. Management must carefully analyze the following elements when designing a hiring plan: 1. Number of positions 2. Hiring schedule (timetable) 3. Critical positions 4. Lead-time for trainee posit ions 5. Characteristics of the ideal workforce This presentation will focus on a proven system that is efficient (and yet simple) for achieving a new concentrator facility's manpower requirements. IDENTIFYING THE STAFFING NEEDS As previously stated, the key to staffing is planning. Management will find that a basic manpower chart will provide the hiring schedule to meet deadlines. In fact, this system begins with a manpower chart (Figure 1). The chart basically works in reverse of the hiring requirements: the last scheduled hire is the first job on the list. This approach ensures that the company will not find itself compressed against the facility start-up date. A cardinal rule in recruiting a workforce is to allow sufficient time to orient and train employees to the procedures and culture of the system. Problems in selection of personnel begin when the hiring program is short-circuited for timing reasons. The quality of employee selected invariably suffers accordingly. The second section is the key to the success of the manpower program. This is the latest date by which a formal recruiting effort must begin in order for the hire date to be met. Leadtimes are usually as follows: 1. 90 days for company transfer positions 2. 60 days for experienced new hire positions 3. 30 days for trainee positions

Jan 1, 1986

By Chee S. Theng

As the 2015 president of the Society for Mining, Metallurgy & Exploration Inc., I am pleased to present the 2015 issue of the Transactions of the Society for Mining, Metallurgy & Exploration Inc., Vol. 338. A significant portion of the contribution that we make as a professional society is the publication of professional and technical papers that accelerate the advancement of scientific knowledge and enable the transfer of technology. Communication within the mining community is the key to a successful society. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, PA, that resulted in the founding of AIME. Those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume fulfills that pledge. The 2015 Transactions contains some of the most interesting research and insights from the past year and features an international slate of authors spanning industry, academia and government. Papers include the latest findings from the U.S. National Institute for Occupational Safety and Health (NIOSH) and special-focus articles on gold processing, iron ore processing and coal processing. The 2015 Transactions consists of a total of 67 technical papers, encompassing all 22 papers published in 2015 in the Technical Papers Section of Mining Engineering (Vol. 67) and all 29 papers published in 2015 in Minerals & Metallurgical Processing (Vol. 32). Additionally, this volume contains 15 papers and one discussion that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. All of the technical papers were peer-reviewed. The process of review and publication requires much hard work by authors, reviewers and our publications staff. As the 2015 president of SME and on behalf of all our members, I would like to extend our gratitude to all whose volunteer efforts contributed to the publication of this volume.

Jan 1, 2015

By ANGELA NAIR AVELAR, Reiner Neumann, PAULO R. G. BRANDÃO

Three types of apatite were identified by means of cathodoluminescence (CL) images in flotation concentrate and tailing samples from the Catalão Mine in Brazil. They are predominantly blue apatite, followed by green apatite and, less frequently, yellow apatite. The chemical compositions of these types of apatite were determined by electron microprobe analysis and laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS). Blue and green apatite responded well to the process, thus remaining in the concentrate, while yellow apatite remained in the tailings. Yellow apatite has the lowest phosphorus pentoxide (P2O5 ) content and largest anionic and cationic sites substitution, followed by green apatite, whereas blue apatite is the most homogeneous, with highest phosphorus (P) and calcium (Ca) grades and lowest substitution level.

By K. Biswas

For the pillars, which have been standing long after mining, the stability depends much on the weathering action in the presence of mine moisture. From the field observations, it has been found that this weathering action becomes critical in terms of pillar stability if the coal seam contains partings or binders in it. The weathering action degrades both the partings and coal in terms of their load bearing capacity as the mine moisture penetrates into them. This paper investigates the effect of weathering action on coal and partings in the laboratory. In the field, the strength profile in the coal and the partings and the effect of time (in terms of the pillar age) on them have been studied by using borehole penetrometer. In this paper, an attempt has also been made to establish formulae for time dependent strength of coal and partings.

Jan 1, 1997

By Howard Lum, Sergio Valles, John Bednarski, Gordon Enas, Jay Arabshahi

"Water drawn from the Sacramento-San Joaquin Delta provides water supply to 66 percent of California’s population and supports the state’s agriculture industry. The existing through-Delta water system is outdated and unreliable with environmental risk to some fish and wildlife species. The Bay-Delta Conservation Plan (BDCP) has been established to environmentally retrofit and modernize California’s water delivery system through the Delta by restoring habitats, constructing new diversion points in the north Delta and providing a means to transport water supplies under the Delta, rather than through sensitive natural channels.Under BDCP, the Delta Habitat Conservation and Conveyance Program (DHCCP) has developed several alternatives to convey water from the Sacramento River in the north to the existing pumping facilities in the south Delta through an isolated conveyance system. The new conveyance system would become an integral part of the State Water Project (SWP) and the federal Central Valley Project (CVP) by transporting water to the export pumping plants for each of these projects. The DHCCP is managed by the California Department of Water Resources (DWR), while state and federal water contractors provide technical support to the program.The initial conceptual study efforts on the overall program commenced in 2007 and examined various options for the proposed conveyance system. Several conveyance alternatives were analyzed at that time. The Conceptual Engineering Report published on Oct. 1, 2013 identified the modified pipeline/tunnel option (MPTO) as the preferred alternative to be included in the BDCP environmental documents. MPTO includes three river intakes and pump stations along the Sacramento River, various sizes of pipelines and tunnels, junction structures and two forebays that are capable of delivering up to 4 million gpm (9,000 cfs) from the Sacramento River to the SWP and CVP. The river intakes are located near Hood in Sacramento County approximately 64 km (40 miles) from Clifton Court Forebay (CCF) in Contra Costa County. This route would cross portions of Sacramento, San Joaquin and Contra Costa counties. Figure 1 depicts the configuration of the MPTO alternative."

Apr 1, 2016

By Stuart R. Cotterill

Open cast surface mining requires blast hole drilling with many interesting facets in order to achieve mine planning forecasts. Interestingly, no single method or combination of theoretical hypothesis of mining economics is right for all conditions. On occasion mine planners introduce a project with little or no regard to drilling and blasting. Generally, drilling and blasting costs are a significant percentage of total mine overhead. One such drilling and blasting method which can be utilized to reduce overall mine expenditure is inclined or angle hole drilling. One must bear in mind, that angle hole drilling per-se mill not reduce costs, unless a set of required circumstances is met. An attempt will be made to detail when conditions of the mine design criteria dictate the use of angle drilling.

Jan 1, 1984