Search Documents

By Wen Lan Chen

In the plant where the 800m diameter cyclone was tested, 500 STPH of 50m x 0 raw coal was pulped in a heavy medium tank and pumped originally to four 700mm heavy medium cyclones. For the test one of these units was replaced by an 800mm diameter cyclone with the subsequent feed pressure for both units sets at approximately 15.0 psi. Since this was a feed to zero plant, an appropriate bleed of heavy medium to the dilute medium circuit was established to en- sure that the cleaning of the 500m x 0.5mm raw coal would not be adversely affected by high levels of 0.5mm x 0 fine coal present in the heavy medium. The medium gravity measured varied between 1.41 and 1.43. During a three-hour test on June 10, 1983, the raw coal sample was collected from the feed belt while the clean coal and refuse samples were collected separately at proper locations along the product streams of the two different diameter cyclones. All of these samples were shipped to the laboratory for screen and sink- float analyses. The raw coal screen and ash analyses are shown in Table 1.

Jan 1, 1984

By D. G. Chedgy

Careful consideration is given to the type of cleaning equipment and control sys- teas to be used when selecting circuits for wash-ing fine coal (28M x 0 size fraction). However, the desliming, declaying and sizing procedures required to ensure efficient operation normally are not evaluated in sufficient detail resulting in disappointing system performance. This paper details desliming and dewatering circuit design which is extremely effective based on recent test data. The circuit maintains control of the 28M x 0 (declayed) size fraction with minimal misplaced material and maximized circuit efficiency. A discussion of circuit design parameters and control systems, as well as results from the testing program, are included in this text.

Jan 1, 1986

By V. K. Reddy Kallam, NEHA PANDEY, Sunil Kumar Tripathy, ARIJIT BISWAS

The study investigates SO2 leaching of low-grade ferruginous manganese ores to selectively recover manganese as MnSO4 and produce battery-grade electrolytic manganese dioxide (EMD). The effects of leaching parameters (duration, temperature, SO2 flow rate) on Mn recovery were studied. Under optimum conditions, 97.9% Mn recovery was achieved. The MnSO4 leach liquor was purified and used for electrowinning EMD with 88.01% purity and battery-active γ structure.

Apr 20, 2022

By A. L. Slaughter

A mineral deposit has been discovered and explored sufficiently to establish the presence of ore in ?commercially marketable quantities," This is the point at which exploration ends and development begins, Of course, when the presence of commercially marketable quantities of ore are thought to be present the deposit had to be evaluated before this decision could be reached. If, on the other hand, it was thought that commercially marketable quantities of ore are not present, either more exploration has to be done or the project must be abandoned. It is this decision with which this paper is concerned, more particularly, the influencing factors behind this decision. The final question to be answered is: what profit can my company reasonably expect to make by developing this property and putting it into production? The answer must be expressed as a figure for final profit per ton, money which can be used to pay dividends or to build up cash reserves. Some acquisition cost has probably been paid and the exploration cost incurred at the time of decision, (abandonment or development). In addition to returning these acquisition and exploration costs, the deposit must pay development, mining, milling, capital expense of new plants and equipment, taxes, and various other related costs.

Jan 1, 1958

By Kaige Zheng, Hongwei Wang, Tong Wang, Yanjun Li, Yongping Wu, JIANQIANG JIAO, Baolin Jiang

Due to the influence of economic development on the demand growth of coal resources, many mines in China have gradually entered deep mining. When the roof of deep coal seam is hard rock, it is easy to cause strong ground pressure with the advance of the working face, which seriously threatens the safety of coal mining. Taking 31,104 working face of a mine as the engineering background, this paper studies and compares the deformation characteristics and stress transfer evolution law before and after the presplitting of the hard roof through the combination of physical similarity simulation, numerical calculation, and field measurement, based on the analysis of the interaction relationship between the breaking and collapse of the composite hard roof, and verifies the treatment effect of hydraulic presplitting through field measurement. The results show that: (1) In the early stage of mining under the composite hard roof, the lower roof is mainly subjected to tensile failure, the voussoir beam structure formed is relatively unstable, and the stope is prone to impact. When the mining distance of the working face is large, the breaking rotation of the upper hard roof voussoir beam causes pressure damage to the lower hard roof, causing the lower hard roof voussoir beam structure to slide and lose stability, resulting in strong ground pressure in the working face. (2) After presplitting of composite hard rock stratum, in the early stage of mining, the range and degree of rock stratum damaged by presplitting are small except for the hard rock stratum itself, and the presplitting effect is not significant. When mining to the first square position, the roof is damaged in advance by presplitting, the overall plastic damage range increases, the damage form area increases, and the damage degree deepens. The vertical displacement of the composite hard roof increases rapidly, and the presplitting effect is remarkable. (3) The evolution characteristics of roof principal stress transfer show that under the dual effects of mining and presplitting, the roof tensile stress area above the goaf is large, the rock failure horizon rises, and the roof failure height is high and the failure degree is deep. The stress concentration degree of the coal mass in front of the goaf is reduced, and the stress concentration range is transferred to the rock mass in front. With the advance of mining, the hard roof in front can break and caving in time, so as to avoid rock burst disaster caused by large suspended roof area. The field ground pressure monitoring shows that the average periodic weighting interval, weighting range, peak value before weighting, and peak value during weighting of the working face after presplitting decrease by 53.5%, 38.03%, 8.63%, and 5.96%, respectively, which effectively reduces the weighting intensity and ensures the safe and efficient mining of the working face.

May 16, 2023

By E. A. Gyawu, L. L. Eng, M. Fikru, K. Awuah-Offei

Investors and other stakeholders are increasingly concerned about the quality and quantity of sustainability disclosures as well as the extent to which such disclosures correlate with sustainability practices of mining firms. This is because disclosure policies vary widely across firms in terms of extensiveness, materiality, and disclosed topic. In this paper, we conduct a preliminary examination of the relationship between sustainability performance and disclosure. We use sustainability performance indicators such as water and energy use and the Sustainability Accounting Standards Board’s (SASB’s) standards to evaluate disclosures. Our preliminary results show that some measures of sustainability performance (energy use) are negatively correlated to the amount and quality of disclosures while others (water use) are not. Thus, investors should not judge sustainability performance based solely on the amount and quality of sustainability disclosures. In addition, our results suggest that firm size and ownership as well as institutional membership could impact the strength of correlations between disclosure policy and sustainability performance

Mar 2, 2022

By Muhammad I. Kabir

A new minitest of in situ uranium leaching processes at reservoir conditions is proposed. The test which consists of a single observation/ production well and two observation wells is designed to permit the evaluation of both restoration and leaching parameters. It is shown that by using a straight forward history matching procedure, sometimes called a type curve analysis, both the rate of leaching and the ultimate uranium recovery can be evaluated based on the results of the test. Type curves are presented for the case in which the reaction rate is kinetically controlled and there are no other minerals competing for oxidant. Other situations can be approached using the same techniques as those presented here.

Jan 1, 1981

By F. A. Edwards

The Macassa Division of Lac Minerals Ltd. is a high grade gold mine that has been operating in Kirkland Lake, Ontario for the past 51 years. It produces approximately 120,000 tonnes of ore per year, averaging approximately 18.7 grams per tonne (0.45 ounces per ton) of gold. Over the years, the ore body has been developed to a point where mining takes place below the 1,220 m (4,000 feet) elevation and 1,830 m elevation (6,000 feet) west of the original shaft. The mine is currently serviced by two surface and two winze shafts. (Figure 1). The ore body extends below the 1,930 m (6,400 feet) Level which is the bottom of the existing mining operation. An ambitious underground exploration program has substantially increased these reserves. Concurrent with the discovery of greater reserves, has been rapidly escalating mining costs, particularly labour which constituted 66% of the total cost in 1981. These costs continued to escalate as the major proportion of mining was carried out to the west, far away from the existing hoisting systems. This required a three lift hoisting system for men, materials and ore. In addition to the increased travel time and ore handling expense, increased humidity, temperature, ventilation and compressed air losses have added to the inefficiency of the operation. As a result, studies were initiated in 1980 to assess the future of the Macassa operation. The results of the studies indicated that a new deep shaft with a potential to hoist from 2,135 m (7,000 feet) or below was the most attractive option. Detailed design of the shaft and associated surface plant commenced in January, 1982 and the following milestone dates were achieved: 1980 - initial study of hoisting and haulage facilities; January, 1981 - ore reserves in excess of 1 million tonnes of ore at 18.7 g/tonne (0.45 oz/ton) confirmed; March, 1982 - preliminary study of Macassa No. 3 Shaft completed; April, 1982 - permanent hoisting plant purchased; June, 1982 - site clearing commenced; September, 1982 - shaft collared; May 1, 1983 - shaft sinking commenced; February 11, 1985 - shaft reached 1,600 m (1mile); December 1, 1985 - shaft scheduled for completion.

Jan 1, 1985

By Guillermo Krstulovich

Pillar strength is a fundamental variable in the design of room and pillar mining. A number of researchers have investigated the strength of mine pillars by loading cubical, cylindrical and rectangular model pillars to failure in a compression testing machine (1). Several of these researchers have observed an increase in the compressive strength of model pillar with an increase in friction at the platen-specimen interface (2, 3, 4, 5). It has been postulated that the friction prevents lateral expansion of the specimen, thereby exerting a confining pressure at the interface. Seldenrath and Gramberg in their work with cylindrical specimens of limestone and marble noted that the effect of clamping the ends of the specimens, i.e., to restrict lateral movement of the specimen face, was to increase the compressive strength about 10% for marble and from 50-75% for the limestone, as compared to the same type of specimens when tested with the end planes free (6). No attempt was made to determine the confining pressure exerted by the clamps. In recent years, Bureau of Mines has conducted an extensive study, similar to Seldenrath and Gramberg's, with dog bone specimens. The confining pressure exerted by the clamps was determined and an increase in the compressive strength with increasing confining pressure noted (7, 8).

Jan 1, 1970

By F. G. Miller

Over the past 30 years, the coal industry has been continually striving to perfect methods for cleaning fine coal to acceptable ash and sulfur contents while maintaining maximum product yield. The flotation process has been part of this effort and its importance is expected to grow as new utilization technology demands finer and purer coal products. The work outlined in this paper is part of a larger effort aimed at development of new and improved flotation systems for removing sulfur and ash from as-mined coal as well as for producing super-clean coal for future markets. The concepts and data presented are now serving as a basis for designing fine-coal circuits in which improved efficiency is obtained by optimum use of flotation.

Jan 1, 1986

By S. Wegerer, M. Semel

The search for minerals typically starts with a reconnaissance phase. After finding a promising target area, further prospecting work will be conducted. Finally with growing confidence of having encountered an ore deposit with commercially viable concentrations of relevant minerals, an extensive exploration campaign will verify its potential. Best practice and reliable, efficient tools for mineral resource estimation of massive sulfide deposits in the deep sea have to be established yet. Therefore, a new seabed exploration system is in development. Various challenges are caused by the extreme environmental conditions in the deep sea and by the nature of massive sulfide deposits. Information of past and ongoing expeditions were gathered to form the basis of an in-depth requirement analysis. System functions and corresponding process times were derived. The experience from the existing MeBo seabed drill rigs serve as starting point for the concept study and following development. Initial MeBo system was built for maritime research purposes and now has to be converted into a new design, suitable for efficient and economic resource exploration. The new system configuration is modular structured to adapt easily to different application scenarios and challenges. To achieve an extension of the deployment depths, the overall equipment weight has to be limited through light weight construction and material. The drilling module contains a range of geotechnical coring tools to face the varying soil conditions of heterogeneous massive sulfide formations. The major challenge to overcome is the touch down sequence on uneven, 25° inclined, rough terrain in up to 4.000 m water depth. Furthermore, high precision of the final unit positioning is necessary. Landing sub-system proof of concept is validated in laboratory environment with small scale model. A novel seabed exploration system capable to land and operate safely on highly inclined slopes of mineral deposit is described. Obtaining high quality samples by wire-line coring technique is the objective.

Feb 22, 2026

By J. M. Mutmansky

Procedures for the determination of the operating point that results when a fan is connected to a mine and placed in operation have been a source of confusion for decades. A variety of techniques has been proposed, often to the detriment of the practicing ventilation engineer trying to apply the techniques to the multitudinous mine/fan matching problems encountered in the engineering of mine ventilation systems. This paper proposes some different assumptions and definitions that simplify the solution of problems in determining the operating point. As a result, a set of procedures is provided for determining the operating point of a mine/fan system when the outlet areas of the mine and fan are known. To establish a major simplification in the development of procedures for the determination of the operating point for a mine/fan combination, the authors suggest that the mine pressures be redefined and then used in such a manner that the conservation of energy is ensured. This provides the basis for the recommendation that the fan operating point be determined using the fan total pressure and the system total pressure characteristics. This procedure can be applied to fans in the blower, booster, and exhaust positions equally well and to both single-fan and multiple-fan networks. Another advantage is that the method is applicable to fans with or without an evase.

Jan 1, 1984

By O. J. R. Baena, N. J. Zapata

In Colombia, more than 15 regions and around 100 municipalities develop gold mining at different scales, and these operations generate mining waste composed of processing fluids and crushed rock with metals and high silica content. Cement production requires clinker, gypsum and other corrective additives. Clinker results from the partial fusion of some minerals including silica. In this study is proposed to evaluate the effect of the use of mining tailings sands from gold mining in the manufacture of clinker. The proposed methodology will allow the characterization of the sands to manufacture a cement specimen and measure its physical and fire properties

Mar 2, 2022

By Richard H. Johnson

White Pine Copper Company, a subsidiary of Copper Range Company located in Michigan's Upper Peninsula, mines a Precambrian sedimentary deposit containing finely disseminated chalcocite, native cop- per and native silver. Silver occurs predominately in certain strata and presently provides a mill head averaging 0.25 ounces per ton. This technical publication traces the development of silver recovery at White Fine beginning in early 1961. White Pine refined copper contains an excess of silver over and above that required to impart Lake Copper properties. The copper does not require electrolytic refining to meet industry purity requirements, nor is there sufficient silver to justify electrolysis.

Jan 1, 1970

By Mahaboob Basha Shaik, Shakuntala Tudu, Indrajit Paul, Chandra Sekhar, Neha Gupta, Amit Kumar, Srinivas Dwarapudi, Arvind Kumar Patel

In this study, the effect of colemanite and calcined colemanite (CC) addition on the properties of iron ore pellets is studied. The pellets are prepared in a lab without and with 0.2% colemanite and varying amounts of CC from 0 to 1.0 wt%in steps of 0.2%. A reference pellet is prepared under typical plant conditions, and the properties of the reference pellet are considered as the base value for improving the cold compressive strength (CCS) while maintaining the other parameters at an acceptable limit without altering the pellet. The study also aims to provide a detailed characterization of colemanite and calcined colemanite to better understand their behaviour during firing. The lab-scale results show that the CCS of pellets made with 0.2% colemanite was reduced by 222 points (60%) as compared to the reference pellets due to crack formation during firing. The results show an improvement in the CCS of the indurated pellets with CC dosage up to 0.4%, and decreasing strength is noted thereafter. It is observed that the swelling index increases with the increase in calcined colemanite dosage. To simulate plant conditions, reference pellets and pellets with optimized CC dosage were fired in a plant furnace.

Oct 16, 2020

By Peter Dietrich, Joseph DeMello, Norbert Fuegenschuh, Kerwin Hirro, Jeff Brandt, Mike Cole

This paper presents a successful case history of the ground improvement efforts and excavation of twenty-three cross passages between twin bore tunnels driven by EPB tunneling machines in Los Angeles, California on Section 1 of the Westside Subway Extension. Unique and complicated ground conditions local to the tunnel alignment include San Pedro sands, siltstone/claystone Fernando Formation, and zones of “asphalt impacted soils.” To provide water cut-off and soil stabilization, jet grouting was performed prior to TBM excavation at the location of many of the cross passages. However, upon investigating the cross passages prior to excavation, the subsurface conditions required additional measures and SEM tools to ensure successful completion of the project.

Jun 13, 2023

By S. Potgieter-Vermaak, T. T. Chiweshe, W. Purcell

The advantage of using ammonium phosphate salt as flux is the selective precipitation of chromium(III) compounds, which are considered nontoxic and environmentally friendly. The technique in this paper is determined to have potential to be applied in the metallurgical industry, where it can be used in the beneficiation of chromite mineral ores. The higher chromium contents of chromite ores often require furnaces to run at higher temperatures of above 1,300 °C, which can cause shutdown of the ore processing plant and accumulation of the sticky chrome compounds — including toxic chromium(VI) waste — which are generated as byproducts. The other advantage of this technique is its low to moderate energy consumption compared to existing techniques.

By John M. Hill

Automation technology has many facets, some well tested and proven, some yet to be put to the acid test of economic reality. In this paper, we will limit our purview to the former. Consider, if you will, an automated handling system combining high-speed conveyors and automatic devices on-line which not only provide signals for routing and sorting, but also format those signals for the production of manufacturing, inventory, shipping and billing paperwork. This is not futuristic, but practical and a realistic accomplishment. Therefore, the following discussions will address today's challenges not with tomorrow's solutions, but rather, with an established technology which is playing an increasingly prominent role in materials handling systems. Until recently, relatively modest importance has been attached to the timeliness of information feedback from the production or assembly line, warehouse or distribution center. Thus, initial applications of automatic identification equipment focused almost exclusively upon the control of materials flow - that is, routing, sorting, etc. However, these systems have performed successfully and quietly established an enviable track record as reliable materials control tools.

Jan 1, 1973

By P. Muduli, Y. Xi, T. M. Yegulalp, A. J. Arias

A short review of current practices and recent developments is followed by a description of a newly developed approach for solution of the optimum, ultimate pit limit problem. The new approach utilizes network modeling of the problem for solution by maximum flow algorithm. The latest developments in the implementation of maximum flow algorithm present significant time and memory savings as compared to initial development due to Ford and Fulkerson (1956). Results of a series of computational tests are presented to demonstrate how this approach performs as compared to the well-known Lerchs Grossman algorithm. It is also shown that the solution by the new method automatically includes several optimal solutions based on a predetermined number of benches to be included in the analysis.

Jan 1, 1994

By Douglas W. Huber

During the past decade, a general awareness of the need for and subsequent development of increased safety in United States coal mines has taken place. Government and industry alike were stimulated into accelerating their actions through unacceptable accident statistics and costs (in terms of human misery dollar values). Those of us who work in the United States coal industry are aware of the development of governmental controls on nine safety. Both Federal and State regulations have placed increased responsibility upon mine owners and operators to insure a safe working environment and to provide training for miners. No other industrial group of workers has received such attention or, in our opinion, deserves it more.

Jan 1, 1982