Search Documents

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this study is to assess the impact of different reagents, such as limestone, lime, magnesium oxide, and sodium hydroxide, in experiments carried out in the single purification step and in two consecutive purification steps by raising the pH of a rare earth sulfuric liquor with the aim to remove or reduce the impurity concentrations in the rare earth sulfuric liquor. The choice for the best purification condition was made based on the minimum loss of rare earth elements (REEs), reagent consumption, and residue generation. The exploratory experiments show that it takes place in the two consecutive purification steps, the first one consists in dosing the limestone pulp until it reaches a pH of 3.5 followed by an addition of a lime pulp reaching a pH of 5.0. Under this condition, the results were a total removal of Fe3+, PO4 3− , and Th4+ ions and a reduction of 99%, 87%, and 37% w/w in the Al3+, UO2 2+, and SO4 2− concentrations, respectively, in the purified rare earth liquor. Furthermore, the lowest REE losses (8.3% w/w) and reagent consumption (4.3 kg/m3 ) and also a low residue generation (7.5 kg/m3 ) were observed in this condition. Despite reaching similar results regarding impurity removal, the experiments done with the addition of limestone, lime, magnesium oxide pulps, and sodium hydroxide solution in the single purification step, where the pH was raised to 5.0, presented higher REE losses (64.9%, 42.5%, 44.8%, and 60.9% w/w, respectively) and a higher residue generation (43.2, 25.1, 11.1, and 13.6 kg/m3 , respectively). This occurred due to the co-precipitation of salts containing rare earth elements in their composition. The experiments conducted with limestone, lime, and MgO resulted in a higher consumption of reagents, while the same result was observed when NaOH was used (4.3 kg/m3 ). In the experiments carried out with the addition of magnesium oxide and sodium hydroxide, the respective purified rare earth liquors presented a high concentration of magnesium, sulfate, or sodium, which could impact the quality of the marketable rare earth salts, whereas the salts obtained under the best condition observed in this study seem to be amenable for use as raw material in an attempt to obtain rare earth products with an acceptable chemical quality.

By G. Zain, Abdel-Zaher M. A. Abouzeid, Y. S. Mustafa, A. A. S. Seifelnassr

The main forces acting on minerals in conventional size reduction units are compression, impact, attrition, and/or abrasion. Usually a combination of these forces shares the breakage action of the minerals with one or more of these forces dominating the breaking action, depending on the machine used. The present work concentrates on the behavior of quartz when stressed with compression force in a confined piston die. Several size fractions within the size range minus 10 mm to plus 0.85 mm were compressed in the piston die. The measured parameters are compression load, bed thickness, displacement as a result of compression, rate of displacement, and the size distribution of the products. It was found that the size distributions are, to some extent, different from those produced by the ball mill or the high-pressure roll mill. This is mainly because of the differences in the type of the acting forces in each case. It was also found that the cumulative weight of the distributions is reasonably normalizable with respect to the median particle size of the product. The specific energy expended is inversely proportional to the median size of the products, and the reduction ratios, xf/xp, are directly proportional to the applied compression force, and hence, to the specific energy expended. A simple model is suggested for predicting the particle size distribution as a function of the expended energy. The calculated values of the size distributions match fairly well with the experimental values, except at the very low energy levels, where most of the energy expended is consumed in the rearrangement and packing of the particles in the confined space with little or no breakage.

By James M. Link

The transportation of solids by slurry pipeline is a rapidly growing field. Although early patents date from the latter part of the nineteenth century, it has only been within the last twenty years that successful long distance slurry transport lines have come into their own. The pioneering efforts in this country include the gilsonite slurry pipeline from Bonanza, Utah, to Grand Junction, Colorado, and the coal slurry pipeline from Cadiz to Cleveland, Ohio. Both of these lines were constructed in 1957 and had a combined annual capacity of about 360 million ton miles. Although the Cadiz pipeline was mothballed in the early 1960's, the interest in slurry transport systems continues to increase and one engineering and construction company is predicting that by 1980 an annual slurry system rate of more than eight billion ton miles will be achieved. The design and construction of cross-country pipelines for fluids such as crude oil appears relatively simple when contrasted against the complex problems encountered in slurry systems. Considerable effort has been expended in hydraulic research laboratories in an attempt to improve our understanding of slurry behavior. This effort has been rewarded with considerable success and is best illustrated by the large number of slurry systems now planned or under construction. However, slurry transport in pipelines is still, in many instance more of an art than a science. In order to minimize the risk factors in the construction and operation of large scale slurry systems, studies are frequently conducted in pilot scale test

Jan 1, 1972

By P. Bissert, M. Klein, L. Yan, D. Yantek, R. Matetic

"U.S. Mine Safety and Health Administration (MSHA) regulations require underground coal mines to use refuge alternatives (RAs) to provide a breathable air environment for 96 hours. One of the main concerns with the use of mobile RAs is heat and humidity buildup inside the RA. The accumulation of heat and humidity can result in miners suffering heat stress or even death. MSHA regulations require that the apparent temperature in an occupied RA not exceed 95 °F. To investigate this, the U.S. National Institute for Occupational Safety and Health (NIOSH) conducted testing on a 23-person tent-type RA in its Experimental Mine in a test area that was isolated from the mine ventilation system. The test results showed that the average measured air temperature within the RA increased by 9.4 °C (17 °F) and the relative humidity approached 94 percent at the end of a 96-hour test. The test results were used to benchmark a thermal simulation model of the tested RA. The validated thermal simulation model predicted the volume-weighted average air temperature inside the RA tent at the end of 96 hours to within 0.06 °C (0.1 °F) of the average measured air temperature. IntroductionIf an accident occurs in an underground coal mine, miners who fail to escape from the mine can enter a refuge alternative (RA) for protection from adverse conditions, such as high carbon monoxide levels. One of the main concerns with the use of mobile RAs is the potentially adverse thermal environment inside an RA from the metabolic heat of the occupants and the heat released by the carbon dioxide (CO2) scrubbing system. Moreover, the humidity within the RA will increase through occupants’ respiration and perspiration, and from the chemical reaction within the CO2 scrubbing system. The accumulation of heat and humidity can result in miners suffering heat stress, heat stroke or even death."

Sep 1, 2016

By Christopher Mark

Sixty years ago, underground coal mining was the most hazardous job in the United States. Roof falls were a big part of the problem. They killed about 100 miners every year, more than all other causes put together. Fast forward half a century to 2016, which is the first year ever with zero roof fall fatalities. Just three miners were killed by roof falls during the following 6 years. How was this historic goal achieved? This paper starts with a modern analysis of the causes of the roof fall fatalities in 1968. Then it follows the reductions over time by category, using snapshots of the fatalities occurring in subsequent decades. Along the way, it evaluates the influence of the regulatory environment, changing mining methods, and better ground control technology. The paper shows that in 1968, more than half of roof fall fatalities at large mines were attributable to an inadequate safety culture. The immediate effect of the 1969 Coal Mine Health and Safety Act was to reduce the riskiest activities, like needlessly going under unsupported roof. Other hazards, like large roof falls, required technological developments before they were brought under control. Roof control plans, which the U.S. Bureau of Mines had been advocating since the 1920s, played a significant role throughout the process.

Jul 1, 2023

By Don Painter, Nico Sutmoller, Lori M. K. Kahikina, Brian Dorwart

This paper will address the feasibility of using low-density cellular concrete (LDCC) for an annular fill application where project conditions required pumping the LDCC material for distances of up to 16,000 feet. These conditions occurred during construction of the Kaneohe-Kailua Sewer Tunnel in Oahu, Hawaii, between 2014 and 2018. Located on the island of Oahu, Hawaii, this 13-foot-diameter rock tunnel extends for approximately three miles from the Kaneohe Pre-Treatment Facility to the Kailua Regional Wastewater Treatment Plant. The tunnel was built to convey wastewater and provide temporary storage for peak wet weather flows entering the collection system, thereby reducing the potential for uncontrolled discharges. LDCC was chosen for this project partly due to its environmental benefits, which were essential for an application contiguous to the inland marine and coastal waters of the Pacific Ocean. In order to ensure optimal performance characteristics—compressive strength (with a requirement of 300 psi at 56 days), flowability, and light weight—were achieved, extensive testing of various LDCC products and mix designs was completed. The testing measured the initial set time of the LDCC as well as the compressive strength needed to reduce the quantity of grout lifts required for the project.

Jun 13, 2021

By M. M. Veras, C. H. Sampaio, A. S. Young, D. Neto, C. O. Petter

"Due to new technological developments, automatic sensor based sorting has made progress within industrial minerals, precious metals, diamond, and coal mining in recent years (Lessard et. al. 2016). In order to re-introduce the technology to other mining sectors, this research discusses its application to iron, manganese, and zinc ores through test works performed by the authors. These test works were performed using Dual Energy X-ray Transmission (DE-XRT) sensor technology. In each case, pre-concentrations of the ore were created demonstrating the possibility to reduce waste material, energy costs, and water consumption while improving product quality of the ores. INTRODUCTION Sorting of mining ores is as old as mining itself (Salter, 1991). Sensor based sorting applications in coal mining began as early as the late 19th century (Louis 1928). New sensor technologies were developed and implemented sequentially for uranium, nickel, coal, and gold mining (Refining, 1949, Rose et al, 1950, Bloomfield et al, 1966, Clayton et al, 1987, Robben and Mosser, 2014). While these sensor technologies were developed decades ago, computational capacity to keep pace with the vast amount of information required utilizing the sensor technology did not arrive until recently (Lessard et. al., 2016). The sensor based sorting (SBS) process was effectively described by Salter and Wyatt in Minerals Engineering in 1991, and Wotruba and Harbeck in 2010 in the Ullmann’s Encyclopedia of Industrial Chemistry under Sensor Based Sorting. Both descriptions include the following key steps: 1. Presentation of the material or particles. 2. Examination or detection of the material or particles. 3. Processing or analysis of the data generated. 4. Physical separation of the material or particles by external means. Effective presentation of the material or particles is achieved when the sensor is capable of identifying each particle individually. This step requires that each fragment of the material be isolated, and it often involves acceleration of the material fragments by chute or mechanical means, as well as the spreading of particles by vibratory feeders (Salter and Wyatt, 1991, and Wotruba and Harbeck, 2010). The isolated particles typically are conveyed into an area wherein they are subjected to electromagnetic irradiation (except in cases of some radioactive ores), either in the form of x-ray, visible light, infrared, or other energies. A wide range of applications for sensor based sorting exists in the literature. The majority of applications fall into one of two camps, (1) pre-concentration of mineral ores, or (2) characterization of the material during processing (Buxton and Benndorf 2013). While there is much to be gained from in-line material characterization and the resulting control both of quality and processing, this article focuses primarily on the camp of pre-concentration of mineral ores."

Jan 1, 2017

By E. A. Lauha

The Goldstrike Mine is in Eureka County, Nevada, U.S.A., approximately 23 miles northwest of the town of Carlin. The mine is at the north end of the Tuscarora Spur of the Tuscarora Mountains at elevations of 5,300 feet to 5,950 feet. It is part of the Bluestar/Goldstrike sub-district of the Carlin Trend, a northwest alignment of sediment hosted, disseminated gold deposits. The Carlin Trend includes over 15 major gold deposits with production, reserves and geological resources of approximately 65 million ounces of gold (Figure 1). In the Bluestar/Goldstrike sub-district, there are seven major deposits: Betze, Lower Post, Post, Genesis, Bluestar, Purple Vein and Deep Star, plus numerous smaller deposits (Figure 2). Production, reserves and resources for the sub-district are approximately 40 million ounces. Betze and Purple Vein are located on property controlled by Barrick Goldstrike Mines and Bluestar and Genesis on Newmont Gold property. Post, Lower Post and Deep Star occur both on Barrick and Newmont property.

Jan 1, 1993

By L. A. Roe

Calcium carbonate and talc fillers both find use in a multitude of Industries. Each filler has many commendable properties, and often compete for the same market. Quality controls for various grades are exacting and complicated. A detailed comparison of the physical and chemical properties of these two fillers is tabulated and the mining and processing of the ores is described.

Jan 1, 1980

By Adabala Raja Venkata Sai Naresh, Radhakanta Koner

Particle size distribution (PSD) is an essential parameter in assessing the overall efficiency of blasting operations in mines and the subsequent mine-to-mill process in the mining industry. Despite some drawbacks of 2D image analysis techniques in accurately estimating particle sizes in PSD, the mining industry has relied on them for the last three decades. This study proposes the 3D rock fragmentation measurement (3DFM) technique for deducting the accurate dimensions of 3D rock particles for the PSD. 3DFM has utilized different processing algorithms. Images of different views of the non-touching rock particles of varying sizes have been acquired as a data acquisition step of structure from motion technology for generating sparse point cloud. Dense point cloud reconstruction is used to avail finer details of the point cloud using clustering views for the multi-view stereo algorithm. Random sample consensus (RANSAC) algorithm coupled with an unsupervised classification using the density-based spatial clustering of applications with noise (DBSCAN) classifier is employed to extract the rock clusters from the 3D point cloud. Finally, the accurate rock sizes are derived using the hybrid bounding box rotation identification (HYBBRID) algorithm with a root mean square error (RMSE) of 0.10 cm for length, 0.10 cm for breadth, and 0.32 cm for depth. The PSD of rock fragments obtained from the proposed 3DFM technique is found to be matching with the results of mechanical sieving and manual gauging with an R2 values of 0.98 and 0.99, respectively. The 3DFM method can be considered cheaper, more accurate, and computationally faster in determining the rock dimensions for the PSD determination method to enhance the productivity of the mining industry.

Dec 29, 2023

By I. M. Ahmed, R. S. Hassan, M. I. Aly

Extraction and separation of La, Sm and Dy ions from acidic sulfate-phosphate solutions was investigated using a cation exchange extractant, bis(2,4,4-trimethylpentyl) phosphinic acid, CYANEX 272, in kerosene. The influence of shaking time, equilibrium pH, extractant, sulfate and phosphate ion concentrations, diluent type and temperature was studied. The extraction was found to be pH-dependent, and increasing the phosphate ion concentration inhibited the extraction which was found to be endothermic. The stoichiometry of the extracted metal species was found to be MOH.H2OHSO4H2A.A2. Aliphatic diluents were found to enhance the extraction compared to aromatic diluents. The results showed that there was a separation mode between the metal ions when varying the hydrogen ion and sulfate ion concentrations, under the used experimental conditions. The investigated process was used for the recovery of La, Sm and Dy from the acid solution resulting from the leaching of low-grade monazite.

By M. Fig, J. Brune, C. Strebinger, G. Bogin

"A fundamental understanding of flame propagation characteristics through and around obstacles is needed to accurately model methane driven longwall coal mine explosions originating or propagating in the gob. Experimental investigations of methane flames in horizontal cylindrical reactors with simulated gob (i.e. rock piles) were carried out alongside coupled Computational Fluid Dynamics (CFD) and combustion simulations. Stoichiometric methane-air mixtures were ignited in semi-open reactor vessels of 5cm, 9.5cm and 71cm diameter, all with a fixed length to diameter (L/D) ratio of 8.6. This was done both with empty reactors and also with a rock pile placed at the open end of the reactor. The rock pile length to reactor length ratio was fixed at 0.3, and the rock pile height to reactor diameter ratio was fixed at 0.33 for all reactors. The smaller two reactor experiments were modeled with ANSYS Fluent in 2D. Experimental results indicate that for this geometry a similar acceleration mode occurs across scales: that the flame speeds up an average of 40% as it passes over a rock pile with this profile. The model is able to capture several important features of the experimental results, including the significant increase in velocity, the speedup ahead of the rock pile, and the leveling off of the empty tube flame front propagation velocity. INTRODUCTION Explosions in underground coal mines are among the largest industrial explosions, known to result in the rapid combustion of 20m3 of fuel gas or more [1,2] Coal beds hold methane gas under pressure, and when the pressure is relieved through mining activity some of this methane is released. The methane then mixes with ventilation air and, if not sufficiently diluted, may form a combustible mixture, which may result in an explosion. Several large coal mine explosions have occurred around the world recently. These include the 2014 Soma Mine disaster in Turkey that killed 301 people [3], and the 2009 Heilongjiang Mine explosion in China that killed 108 [4]. Other recent mine explosions, including the 2010 disaster at the Upper Big Branch mine that caused 29 fatalities [5], have demonstrated that explosive gases can accumulate and ignite within and around the gob area of a longwall coal mine and then expand into the active mining face and nearby areas, endangering workers and equipment. If enough combustible gas is involved, the initial flame can accelerate, eventually transitioning from deflagration to detonation [6]. Researchers are developing a fundamental understanding of the evolution of the explosion process from the laminar kernel to the fully turbulent regime, and its propagation through obstacles such as those found in the gob. Researchers also studied the initial development of methane flames and the potential for the development of a detonation."

Jan 1, 2018

By L. Thompsen

High pressure grinding has been introduced into many grinding applications. The high pressure grinding roll offers capacity increases of existing plants and savings in operating costs. Also metallurgical advantages could be achieved. The first high pressure grinding roll in a copper mine was commissioned in Arizona in July 1995. This paper provides information about the operating experience gathered during the first months of operation. The current flowsheet will be described as well as further options for plant arrangements.

Jan 1, 1996

By S. Daniel Thompson

In underground coal mining, the specification and control of belt and bunker capacities are complicated by (1) stochastic and intermittent conveyor loading, (2) a limited ability to reduce surge at the mine face, and (3) occasional overlapping of loading from two or more mine faces on the conveyors. Recently, because of longwall mining and other factors, the capacity requirements of most mine conveying systems have risen substantially; as a result, efficient capacity design and control have become important mine planning issues. This paper reviews these design issues and their associated modeling procedures. Design considerations and modeling difficulties are also examined.

Jan 1, 1996

By W. Z. Choi

In our previous work, a population balance model describing the simultaneous processes of size reduction and mineral liberation has been developed. The experimental verification of this model, however, has been limited to a binary mineral system containing only one composite particle class. When considering multiple classes of composite particles, the estimation of model parameters becomes much more difficult. In the present work, a procedure for estimating model parameters for a multiple composite class model has been developed. Emphasis is placed on the direct experimental determination of these parameters. The physical significance of the breakage rate function and the liberation function in characterizing the liberation process is also discussed.

Jan 1, 1987

By Patrizia Pereyra, M. Guzman, C. Toledo, J. A. Rau, A. Ruiz

The use of mining tailings-based geopolymer binder as a substitute for cement can be an interesting alternative to the problem of final disposing of large volumes of them. Indeed, mining tailings have a high silica content, which makes them suitable for geopolymerization. The tailings samples contain Cu, Pb, Zn, As, Sb, Cd and Bi, mainly. X-ray diffraction results show that the tailings are composed of quartz, SiO2 (81%). Geopolymerized tailing samples (GTPS) were obtained by varying the ratio of SiO2/ Al2O3 and SiO2/NaOH. The compressive strength of the GTPS varied between 2 MPa and 8 MPa. The electrical conductivity in the leaching tests varies between 13.91– 16.11 mS/cm2 indicating that ions are present in the solution. However, the pH = 10.5 indicates that acidity is not being generated. The element that mostly leaches is iron. The highest percentage of leaching is observed for cadmium (69%) and chromium (93%). The concentrations of elements are under the maximum permissible limits for water according to the Peruvian legislation. However, mass transfer leach tests and immersion leach tests must be realized.

Feb 1, 2024

By B. W. Cavender

Innovative mining and metallurgical operating techniques or processes can be identified and developed by systematically analyzing change as it occurs within the mine, plant, technology, or industry. Sources of change to be monitored for innovative opportunities include unexpected successes or failures, incongruities between perceived and actual events, process needs, changes in perceptions, and the development of new knowledge. Innovation can be effectively organized, practiced, and managed. The perception of change as an opportunity rather than a threat is mandatory, as is the systematic measurement of innovative performance. Innovation is enhanced by specifically-designed policies regarding organizational structure and staffing, daily management practices, and compensation and incentives.

Jan 1, 1994

By Y. V. Vasylchuk

An algorithm is presented for optimizing the classification of surface mine material subject to excavating constraints. High-resolution, expected-profit models are optimized to classification maps subject to site-specific excavating constraints. This optimization problem defies traditional closed-form analytical solutions. A practical heuristic algorithm quickly determines the optimum final destination for material subject to realistic selectivity constraints. The expected profit could be calculated from an estimated model if the value calculations are all linear; otherwise, simulation could be used. In both cases, a single expected profit for all destinations on a high-resolution grid is the starting point for dig limits optimization. Maximizing expected profit in a risk-neutral manner is correct given the repeated nature of grade-control decisions over relatively short timeframes.

By Ali Jaberi Zamharir, Abolfazl Shoghian‐Alanaghi, Hossein Aghajani, Arvin Taghizadeh Tabrizi

In this study, the leaching rate of molybdenite concentrate was evaluated in sulfuric medium, and the influence of the diverse oxidants including hydrogen peroxide, manganese oxide, copper sulfate on the leaching rate was studied. Also, the effect of the addition of the ethylene glycol to the hydrogen peroxide was studied and results showed that with the addition of ethylene glycol, the leaching rate is increased 55% from 41% up to 80.3%. The optimum condition is achieved as 0.7 M of H2SO4, 4.4 M of H2O2, and 3.5 M of EG at 30 °C within 4 h of leaching time and 500 rpm. Also, inserting the oxygen with the pressure of 6 bar to the leaching autoclave, the leaching rate is increased more up to 86.4%. Finally, the leaching process was studied kinetically and the determined mode of controlling factor was specified based on the activation energy which equals 46.252 kJ/mole indicating the chemical reaction mode.

Jun 5, 2022

By C. H. Grant

The Dew Chemical Company has been engaged in explosives research since 1953. The incentive for this research was based on the desire to find additional markets and uses for magnesium metal of which Dow is a heavy producer. The thermodynamic calculations for explosives incorporating light metals indicate energies approximately twice that of non-metallized explosives currently being used. Early in 1960, we acquired additional patent rights from independent inventors and decided to set up a development station at Virginia, Minnesota, to conduct a commercial testing and market evaluation program with this new product. The actual manufacturing of the explosive was to take place in the bore holes. Due to the complexities involved in controlling the manufacture of the explosive in the bore hole, performance was sometimes in doubt. Furthermore, our experience indicated that the metallized explosive systems could not be evaluated by the standard laboratory methods then being used, and it was necessary for us to look for more suitable research methods. Tests were conducted on several known methods for explosive evaluation. The most promising were the Navy underwater method for energy evaluation, and a modified Livingston crater method intended to compare explosive performance in rock. After shooting over two thousand charges of eight to 60 pounds under water and in taconites and granites with many types of explosives, we have developed a metallized explosive which is now being manufactured at a pilot plant in Virginia, Minnesota, and is being evaluated commercially.

Jan 1, 1963