Search Documents

By James F. McConnell

Federal and State sulfur oxide emission and ambient air quality regulations have been implemented to fulfill the requirements of the Federal Clean Air Act Amendments of 1970. Primary and secondary air quality standards have been established at levels considered necessary to assure the protection of the health and welfare of the public. Standards of performance under this Act have been established to control the rate of sulfur oxide emissions from individual sources so as to protect and to improve the quality of the Nation's air. The new source standards of performance were made rigorous for large coal burning stationary sources. This has had a severe impact on the electric utilities that operate the coal fired steam electric plants which are the largest consumers of the Nation's coal production. States have taken different approaches in State Implementation Plans (SIPS) as approved by the Federal Environmental Protection Agency. Some states, such as Pennsylvania, have chosen to permit moderate SO2 emission rates from existing sources which are not in critical air basins. All are required to meet primary and secondary air quality standards and to limit sulfur oxide emissions from new large stationary sources to a minimum of 1.2 LBS of S02/MMBTU fired. This re- quires a fuel sulfur percentage of about 0.7 for a 12,000 BTU/lb coal. In an effort to develop strategies and technologies to conform to performance standards while continuing and hopefully expanding the utilization of the Nation's coal supply, the electric utilities, the Federal and State regulatory agencies, and other industries and government agencies are considering several alternatives. 1. Natural low sulfur coal 2. Flue gas desulfurization - (FGD) non-regenerative and regenerative 3. Coal gasification 4. Liquefaction and solvent refined coal 5. Fluidized bed combustion 6. Chemical coal cleaning 7. Physical coal cleaning Of these options, only the first and the last can be considered to be widely used in full commercial practice at this time. FGD has certainly demonstrated technical and operating feasibility and is close to being in full commercial practice but it remains to be seen if the large systems under construction are economically and environmentally optimum.

Jan 1, 1975

By Bob Katsiouleris

Having passed through the worst of times for industrial minerals demand, there are signs that the best of times lie ahead. If the downturn was the result of unsustainable economic policy, the path forward has everything to do with sustain-ably meeting the demands of more people enjoying higher standards of living than ever before. Minerals producers must be poised to understand and meet their requirements well into the next decade. Successfully marketing industrial minerals - the building blocks of a growing and increasingly urban world population - will depend on producers? ability to respond nimbly to a rapidly changing and regionally evolving macroeconomic environment. A renewed focus on energy conservation, sustainable agriculture and building practices and consumer demand for products with a smaller environmental footprint will drive product and market segmentation strategies. These trends will not only shape the way industrial minerals producers do business, but also the type of skills and people they will require to run those businesses.

Jan 1, 2011

By Erik Westman, BEN WESTON, SETAREH GHAYCHI AFROUZ, KATHRYN DEHN

One of the most difficult challenges in underground mining is to forecast significant seismic events prior to their occurrence in order to support the safety of miners and to minimize damage to the underground operation. Passive seismic tomography is a tool to image the seismic velocity changes in a rockmass, which can potentially reveal the rockmass behavior before and after a significant seismic event. In this paper, the changes in seismic velocity of the rockmass before and after three major seismic events are investigated to determine whether there are identifiable precursory velocity changes associated with the major seismic events. Conventional mechanics imply that the induced stress at the hypocenter would continue increasing until failure, in the form of an induced seismic event, occurs. With passive seismic tomography we can image changes to the seismic wave velocity distribution within a rockmass and hence infer the changes to the induced stress near the hypocenter. This paper evaluates the hypothesis that induced stress at the hypocenter (as inferred by the p-wave velocity) increases until the seismic event occurs. In addition to analyzing p-wave velocity changes near the hypocenter, changes to the p-wave velocity at “zone centers” were also analyzed. These “zone centers” are regions within the rockmass that consistently have a p-wave velocity that is much higher than the average p-wave velocity for the rockmass. It is found that the p-wave velocity did not increase at any of the three hypocenters prior to the seismic event occurring, however the p-wave velocity did increase in the closest “zone center” for two of the three events.

Oct 12, 2020

Two key strategies for a new generation of mining are developing domestic raw material production and doing so in an environmentally responsible way, according to presenters at the 83rd annual meeting of the SME Minnesota Section in Duluth (the 71st annual University of Minnesota Mining Symposium). From technical sessions detailing how to build com-munity support, to a short course on international perspectives in iron ore mining and processing, the two-day meeting emphasized the potential of Minnesota state deposits and the importance of maintaining productive community relations both locally and globally. The meeting of more than 300 mining industry professionals began on April 20 with a traditional convocation celebrating the values of northern Minnesota. The accompanying tradeshow, with a record 131 booths, showed the speed and vigor of the economic rebound. Keynote speaker Scott Anderson, vice president and senior economist at Wells Fargo, stated the prevailing mood of the conference: ?Wow, what a difference a year makes.? With metal prices and sales up and heading higher, he said, it was clear that the production-centered economic recovery is reaching the mining and the minerals industry. However, Anderson sounded a few notes of caution. Serious threats to economic stability remain, including the burgeoning national de?cit, high unemployment and the still out-of-control foreclosure crisis. Overall, he predicted a below-average recovery and stressed the importance of developing a long-term business strategy.

Jul 1, 2010

By Serhat Özdemir, Derya Öz Aksoy, Pınar Aytar Çelik, Ahmet Çabuk, Sabiha Koca, Hüseyin Koca

In carbonate flotation, oleate has been used for many years as a collector in industrial scale. Compared to sulfide minerals, the flotation of carbonate minerals requires more collector consumption and has lower yield and selectivity. It has been previously shown that surfactin provides higher yields in smaller amounts than oleate in the bioflotation of calcite as one of the carbonate minerals. In this study, the usability of surfactin as a flotation collector for magnesite was investigated. For this purpose, the adsorption of surfactin on the magnesite surface was inspected with analyses such as FTIR, SEM–EDS, contact angle, and zeta potential measurements. In addition, the effect of surfactin on the surface tension of water was also revealed. The same analyses were also performed for oleate as a reference point. All flotation experiments were performed without optimizing with both collectors. FTIR results showed that the surfactin, like oleate, was chemically adsorbed on the magnesite surface. Surface tension analyses showed that the surface tension of water decreased to approximately 32 N m− 1 at 10− 4 M oleate concentration, and this value decreased to below 25 N m− 1 at the same surfactin concentration. According to contact angle measurement results, the contact angle of magnesite was 85° after the surfactin adsorption of 2 × 10− 4 M concentration, while this value remained at 46° for oleate. Finally, according to flotation experiments, high temperatures and high collector dosages are necessary for acceptable flotation recovery with oleate, yet surfactin can produce the desired result at ambient temperatures and lower collector amounts.

Dec 13, 2022

By John Dodd

Advances in the technology of abrasion resistant irons and steels, which could help in combating abrasion and wear in mining operations, are reviewed. Nodular irons alloyed with nickel or copper and molybdenum, with acicular, bainitic or bainitic-martensicic microstructures are described. These alloy irons combine excellent castability and relatively easy machinabilitv with good resistance to wear. Recent progress in the development of high chromium molybdenum alloy irons is outlined, by which high temperature heat treatment of massive castings can be eliminated, alloy costs can be reduced and cracking problems avoided. Data is also given on the erosion-corrosion resistance of these irons. Trends in the development of improved cast steels are outlined. Factors influencing the toughness and abrasion resistance of manganese steels are considered. The 6% Mn 1% Mo manganese steels are shown to have a useful combination of toughness and abrasion resistance. Composite castings are seen as a means of com- bating abrasion in applications involving severe impact. A brief appraisal is given of recently developed martensitic wrought steels with improved weldability.

Jan 1, 1981

By Patricio Vergara Lara, Jorman Barrera

The selection of the production level elevation is one of the most critical strategic decisions faced by large-scale block or panel caving projects. This elevation largely affects project timelines, capital expenditures, resource recovery, and may even constrain the mine’s maximum production capacity. Over the years, many computational tools have been developed to assist in this decision, most of them based on the same principle of maximizing the project value given its production level elevation. However, for large and inclined deposits, or those extending significantly in the vertical dimension and where extraction cannot be achieved from a single level, traditional selection techniques involving multiple production horizons often lead to suboptimal results. This paper proposes a methodology ensuring that the selection of production level elevations in a multiple horizons (“lifts”) case is globally optimized. Input parameters include economic and cost variables, maximum extractable column height, and deepening costs. The methodology is demonstrated through a real case study to illustrate its potential impact on project value.

Feb 22, 2026

By J. P. McCluskey

The effects of air quality regulations passed in the last few years have been felt in a more pervasive way by the electric utility industry than by perhaps any other industry. I'm referring especially to those regulations dealing with the control of air emissions from stationary sources, and those specifying the quality of fuel used. Particularly, I would like to describe some of the effects that these regulations have had on the Commonwealth Edison Company. To put the subject into perspective, a brief descrip¬tion of the company will be presented first. Then, a historical outline of some of the efforts at control of electric generating station emissions will be described. Following this will be an indication of the Company's response to early State and local regulations prompted by the growing pressure for stringent envi¬ronmental control. Finally, the Company's plans to achieve com¬pliance with the most recent, Federally approved, State of Illinois regulations will be summarized.

Jan 1, 1973

By David N. Hedges

This paper discusses the actual recovery and installation of a longwall in a bituminous coal mine in Western Pennsylvania. The coal bed mined is in the Lower Freeport seam which averages 42 inches (1.07m) in height locally. Drainage from the mine is approximately 3.5 million gallons of water per day (13.25 million liters per day). This water deteriorates the mines predominately fire clay bottom making it extremely difficult to move equipment. Support removal is accomplished by pulling the 6 ton (5443 kg) shields out under their own hydraulic power and transporting them by track over four miles (6437m) co the next longwall panel. This paper also discusses the changes that will be made to aid in the succeeding longwall recoveries and installations.

Jan 1, 1984

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Morgana Rosset, Bárbara da Rocha Pereira

High-purity alumina finds application in various electronic industry sectors, with approximately 100 million tons of this compound being produced worldwide. Alumina is acquired through the mining process of bauxite, a rock composed of a mixture of minerals such as gibbsite, kaolinite, hematite, and either anatase or rutile. In 2020, both bauxite and alumina were included in the list of critical raw materials. Due to the demand for high-purity alumina production, the development of a methodology to remove impurities present in the leach liquor from bauxite processing by solvent extraction (SX) followed by precipitation has been widely studied. This work aims to obtain high-purity alumina from bauxite by a solvent extraction process followed by a precipitation step from the sulfur leach liquor obtained by the thorough dissolution of Al and Fe from bauxite. Different parameters were evaluated in the SX step, such as extractant type, pH, temperature, and volume-to-volume ratio. The results indicated that using Alamine 336 as an extractant at pH 0 and room temperature led to an extraction of 90% of Fe and 15% of Al. Aluminum sulfate was completely precipitated as aluminum hydroxide and 55% of Fe using NH4OH. After the calcination procedure, obtaining a 99.9% pure alumina was possible without generating a red mud-similar residue.

Dec 28, 2023

By SUHAINA ISMAIL, NORLIA BAHARUN, SHAIK ABDUL RAHMAN, WAN NUR SYAFIQAH ANUAR, MOHAMMAD REZAEI ARDANI

Hypochlorite leaching system is a strong oxidizing solution for metal sulfides, which are naturally associated with gold extraction. This study evaluated the hypochlorite leaching of refractory gold ore by using the response surface method–central composite design (RSM-CCD) as a statistical approach in determining the optimum condition of gold extraction from refractory gold ore. The studied parameters for the gold recovery were pH (4 to 6), concentrations of Ca(OCl)2 (0.5 to 1.5 M) and NaCl (2.5 to 3.5 M) in the solution. It was found that the maximum gold extraction of 82.46% (13.85 g/t) was achieved at a pH of 4.0 with NaCl and Ca(OCl)2 concentrations of 2.93 M and 1.08 M, respectively. The statistical analysis also revealed that the amount of gold recovery in chloride solution was significantly depended on pH as the main factor, followed by concentrations of Ca(OCl)2 and NaCl.

Jan 8, 2021

By John L. Bolles

The Phelps Dodge Corporation's Morenci Concentrator includes facilities for coarse crushing, fine crushing, grinding, flotation, tailing, disposal, concentrate filtering, and drying. The Morenci Concentrator daily throughput is in excess of 60, 000 tons. The ore milled is mainly a medium-hard monzonite porphyry in which the principal sulfide minerals are chalcocite and pyrite. The ore is transported by rail from the Open Pit Mine to the primary crushing plant located at the concentrator site. Ore is side-dumped from 80¬ton railroad cars into a sixty-inch gyratory crusher. The ore is then conveyed to a. 12, 000 ton coarse ore storage bin. Fine crushing is accomplished by four parallel lines of conventionally stacked crushers in open circuit. Each unit consists of one seven-foot standard cone followed by two seven-foot shortheads. Ti% product of the fine crushing plant is distributed by two tripper cars across a fine ore storage bin. The crushed ore is then fed by variable speed belt feeders into thirty parallel, single stage, closed circuit grinding units. Each of the 30 grinding units consists of one 6' x 23' conditioning drum, one 10' x 10' ha l mill and two 54" duplex spiral classifiers as principal equipment. The dry ore is fed into the conditioning drum with water to dilute the ore to a slurry of approximately 78% solids by weight. An aqueous solution of ammonium sulfide is also added to the conditioning drum. The ammonium sulfide primarily acts as a sulfidizing agent. The ore slurry containing the naturally occurring sulfide copper minerals and the sulfidized copper minerals discharges into the feed scoop box of the ball mill, where milk of lime, collector and-.dilution water are added. The ball mill product slurry is gravity fed: to the classifier pool where water is added to obtain the desired classifier overflow product

Jan 1, 1977

By Neha Shukla, Nikhil Dhawan

The current study examines the extraction of rare-earth elements from trichromatic phosphor of discarded tube lights via baking processes. The Y2O3: Eu3+ (YOX) and BaMgAl10O17: Eu2+ (BAM) phases completely decomposed during acid and alkali baking with > 90% Eu and Y extraction. Prior, selective acid leaching of the YOX phase enhanced the acid baking process at a lower temperature (< 230 ℃). Feed acid baking showed a maximum 87% Tb, 36% La, and 17% Ce extraction at 500 °C, 0.5 h, 1 ml/g H2SO4, and alkali baking yielded 16.1% Tb, 86% La, and 73% Ce at 300 ℃, 0.5 h, 50 wt.% NaOH. The acid baking of the acid-leached phosphor yielded 72% Tb, 95% La, 63% Ce, ~ 95% Y, and Eu extraction at 300 °C, 0.5 h, 1.05 mL/g H2SO4. Lower Tb extraction during the acid baking of acid-leached phosphor can be attributed to the formation of Ba3Tb( PO4)3 and BaTbO3 phases. Insoluble Si3Tb5 phase formation and partial decomposition of CeMgAl11O19: Tb3+ (CMAT) phase in the alkali baking route leads to lower Tb extraction. The acid baking process is suitable for extracting Tb, Eu, and Y, whereas the alkali baking process is suitable for La and Ce. The thermal analysis of phosphor and flux interaction depicts that alkali baking is less energy-intensive than acid baking. In comparison, the one-step acid baking process and the two-step alkali baking process yielded desirable extraction results (87% Tb, total RE (rare earth) 78.5% and 50.4% Tb, total RE 59.3%). The product yield in the acid and alkali baking route of feed, acid-leach phosphor is 36%, 29%, and 39%, 28.2%, respectively, with ~ 98% mixed rare-earth oxide purity.

May 5, 2022

By Clinton Birch

The multiple-criteria decision analysis is a technique that helps to find an optimal solution by evaluating conflicting criteria. In this study, an approach to perform multiple-criteria decision analysis for cut-off grade optimization, which considers the diverse stakeholder groups prevalent in the mining industry, is presented. The optimization model developed in this approach links the resource block model to the financial model, enabling the process to either maximize profit, net present value, revenue to the State, or extend the mine's life. To identify the optimal cut-off grade in each case, the Excel Solver function is utilized. Although it has limitations, the Solver function can still be modified to handle models with thousands of block values for determining input variables based on the target value. Following stakeholder engagement and dialogue, a single weighted average cut-off grade can then be determined. This approach is demonstrated for nine South African Witwatersrand gold mines.

Jun 25, 2023

By Yuexin Han, Wenbo Li, Xinran Zhu, Pengchao Li

A multi-stage fluidization magnetization roasting is a promising method to treat limonite ore. The dehydroxylation of limonite ore is a key reaction in the pre-heating stage. In this study, the dehydroxylation mechanism of limonite was studied in a laboratory fluidization roasting reactor. The samples were characterized using in situ X-ray diffraction, Fourier transform infrared spectroscopy, and simultaneous thermogravimetry and differential scanning calorimetry analysis. The phase transformation and kinetics analysis were studied. Results indicated that the dehydroxylation occurred at the temperature of 250–350 °C with the vanish of hydroxyl functional groups (-OH). The dehydroxylation kinetics followed the 2-D diffusion (Jander) reaction model G(α) = [1 − (1 − α)1/2]2, and the calculated activation energy was 113.43 kJ·mol−1. This study is conducive to exploiting limonite ore resources using magnetization roasting technology.

Nov 2, 2023

By S. W. Cavender

The analysis of the results of metallurgical experiments is often complicated by experimental errors and uncertainty, the complexity of the system being studied, and the confusion of correlation with causation. Consequently, comparative statistics are used to determine if a difference exists between the outcomes of tests, an estimate of this difference, and the precision of the estimate. This paper reviews the use of significance tests and confidence intervals for the comparison of results from two tests, the use of reference distributions, and blocking and randomization techniques to reduce unavoidable sources of variability. These techniques are demonstrated using plant and laboratory data.

Jan 1, 1993

By Francis J. Quinn

The Natural Gas Act, of 1938, which put interstate pipelines under the jurisdiction of the Federal Power Commission, did not place a protective competitive shield around such companies - nor does any provision of the act guarantee them a profit. Natural-gas pipelines are competitive with each other and also with the coal and oil industries. Gas distributing companies must compete not only with the coal and oil industries, but also with the electric industry. Natural gas has captured markets from oil, which had taken them from coal. Oil men contend that gas prices have: been, held to an artifically low level by regulation. The electric industry is moving into the space-heating market, which pleases the coal people because the coal industry&apos;s largest customer since losing the railroads to dieselization has been the electric companies. The coal industry is attempting to monopolize the industrial and electric generating market through government intervention, and this is being done under the guise of concern for the national welfare through advocation of a "National Fuels Policy purporting to, further the cause of fuel conservation. Such a policy is contrary to American principles and would result in the individual&apos;s loss of freedom of choice and ultimately, in less reserves of preferred fuels because of diminished exploration efforts.

Jan 1, 1961

By M. Govinda Raj, S. Sridhar, M. Aruna

Hand-transmitted vibration (HTV) exposure is associated with various health risks for operators of mobile mining equipment (MME). The case–control research was conducted to determine the musculoskeletal disorder (MSD) risks associated with exposure to HTVs in the exposed (case) and non-exposed (control) groups. HTV readings were measured at the interface between the hand and the steering device using the SV 105B triaxial hand accelerometer connected to the SV106 human vibration analyzer involving 40 MME operators in accordance with ISO 5349:2001 guidelines. A questionnaire survey was also carried out among both the study groups using Cornell Musculoskeletal Discomfort Questionnaire. The European Union's 2002/44/E.C. was used to assess the health risks posed to the MME operators. Twenty-eight out of the 40 MMEs were generating HTVs exceeding the stipulated daily limits of vibration, putting 70% of the operators at increased risk for developing MSDs. The case group was found to have an elevated risk of exposure with odds ratio (OR) 7.56 (95% confidence interval (CI), 1.159, 49.39) and OR 12.80 (95% CI, 2.436, 67.285) times more likely than the control group to suffer discomfort in the left shoulder and left wrist, respectively, indicating increased risk of exposure to HTV. Additionally, cases had elevated risk associated with exposure to tobacco, OR 9.35(95% CI, 1.856, 47.129) compared to those who did not use tobacco. MSDs were more prevalent in the case group compared to the control group. This observation was validated by the field investigations and the responses of MME operators to the questionnaires.

Aug 2, 2022

By Inoka E. Perera, Robert Hildebrandt, Gerrit V. R. Goodman, Krzysztof Cybulski, Zdzisław Dyduch, Michael J. Sapko, Marcia L. Harris

To prevent coal dust explosion propagations, rock dust needs to be lifted and suspended in the air with the coal dust during an explosion. The addition of anti-caking agents prevents caking of rock dust in the presence of water. Mining and rock dusting processes can frequently create alternating layers of rock dust and float coal dust on mine surfaces. For this test series, a thin layer of coal dust was distributed on top of a layer of either treated or non-treated rock dust in the Experimental Mine Barbara, Poland. The experimental results compare the effectiveness of treated and non-treated rock dusts to attenuate a propagating coal dust explosion initiated with either strong or weak methane explosions. Experimental results indicate that the treated rock dust performs better than non-treated rock dust in arresting a propagating explosion, especially in the presence of moisture.

Jan 20, 2020

By H. Simpson

Middelburg mine is an opencast export mine operating in the Eastern Transvaal Coalfields of the Republic of South Africa (Figure 1). The mine was commissioned in 1983, to its original design capacity of 4.25 million sales tonnes which was subsequently raised to 5.5 million sales tonnes in 1989. This increase in export tonnage was brought about through an increase in the mines export allocation and the revision of management strategies. The maintenance of this increased tonnage with minimal additional capital has been achieved through improved operational efficiencies and the upgrading of planning operations through the purchase of an Enhanced Mine Scheduling Software Package (EMSSP/MINESTAR). Simultaneously with this requirement were additional factors that contributed to the implementation of the EMSSP. The mine was owned by a joint venture of two partners and is operated by Middelburg Mine services (Rand Mines Pty. Ltd) (Figure 2). This structure of ownership required the evaluation of numerous planning options to be under-taken concurrently and hence the need for an efficient streamlined scheduling pack-age that could fulfill this requirement. Compounding the EMSSP needs further, were the problems experienced in the export market, these being the external pressure from current and new suppliers in the market place which obliged management to provide solutions to rapidly changing market conditions. These fluctuating market conditions have had a direct effect upon the mine&apos;s planning strategies because of the large percentage of the mine?s sales sold on the international spot market. The sanction factor for all South African exporters has had a negative effect upon price and this was compounded further through internal competition in 1987 via suppliers attempting to maintain the market position.

Jan 1, 1991