Search Documents

By Robert Hochscheid

When the original water-only cyclone patents were established in the 1950?s, the supplies of low cost oil and natural gas were abundant and low selling prices for metallurgical and steam coal provided little incentive for developing more sophisticated coal cleaning systems. Bituminous coal sold for less than $5.00 per ton, and in this period many domestic coal producers discarded to the slurry pond the coal finer than 0.5-mm. For many producers, the selling price would not permit the recovery of the capital and operating costs required for dewatering and drying the fine coal. Water-only Cyclones Clean Fine Metallurgical Coal The first broad interest in the water-only cyclone became evident in the mid- 19601s, and though some work was done on coarser coals, investigators were particularly interested in cleaning coal finer than 0.5-mm. Flotation was the only fine coal cleaning method that was broadly accepted, but short-comings were recognized and investigators were looking for an effective fine coal cleaning device or system. Because of the greater market value and the need for reducing pyritic sulfur in metallurgical coals, much of the development work of the 1960's was done on coking coals.

Jan 1, 1981

By C. Dan Kealy

Recent antipollution legislation for the control of mine tailings and waste-water has required an increasing number of tailings ponds. Many of these new waste-retention ponds are being constructed in congested locations, or the older ponds have reached such a size that--if failure occurs--they pose a threat to human life and public property. Although the typical tailings-disposal embankment represents--to the casual-, observer or the economy-minded mine official--a rather ugly but benign and stable pile of waste, they are in fact an extremely sensitive structural mass, retained behind the frailest of dikes. Failure of the waste mass requires only a minor change in water retention or weather conditions, erosion or piping of the ground strata, shifts in load or slight earth tremors. When failures occur, the results can be disastrous. In the U.S., we have been fortunate that, so far, pond failures have not caused loss of life. Thus, failures in this country have attracted little public attention. Present tailings-pond construction methods used by the mining industry require the barest money investment, and little engineering effort. Unfortunately, this superficial approach may increase short-term profits, but the practice may be conducive to the construction of needlessly weak structures. In coming years many of these designs will probaly become corporate liabilities. A typical pond is portrayed in Figure IA. This particular pond in Arizona is 1 mile long and 3/4 mile wide. Illustrated in Figure lB is a representative pond in cross section. This paper in concerned with two basic features common to all tailings disposal: (1) location of the phreatic surface within a tailings-pond embankment because of its influence on embankment-slope stability, and (2) prediction of

Jan 1, 1971

By K. Ananthpadmanabhan

Hydrolyzable surfactants such as fatty acids and amines undergo, in addition to micellisation and precipitation, various associative interactions in aqueous solutions to form ion molecular complexes such as acid-soap, dimers etc. depending upon the solution conditions such as pH. The interaction of these collector species with the mineral surface and with other dissolved species in solution will play a significant role in determining the interfacial processes such as adsorption and flotation. Marked differences in the hydrophobicity imparted to the mineral surface depending upon the solution conditions such as Ph can be attributed to possible differences in surface activities of the above complexes. This aspect of solution chemistry of flotation systems is discussed here for two widely used collectors namely, oleic acid and dodecylamine. Equilibrium species distribution diagrams based on the available literature .data and on estimates of energy of interactions between molecules, have been obtained for oleic acid and dodecylamine solutions.

Jan 1, 1978

By B. Boutilier, R. Mendoza

"First Majestic Silver Corp. (FMS) is a silver mining company founded in 2002 that operates exclusively in Mexico. It has six producing silver mines, one of which is the La Encantada silver mine (La Encantada) located in the state Coahuila. La Encantada is located near the southern United States border and 708 km (440 miles) north of the city Torreon.La Encantada is located in the Sierra Madre Oriental and is a high-temperature carbonate replacement deposit. Mineralization in La Encantada occurs in many different forms such as veins, chimneys, breccia pipes and reefs (mantos). Mineralization is mainly oxides of iron, zinc, lead and manganese, with high concentrations of sulfides at depth relating to two main intrusive events: the Milagros Intrusive and the La Prieta Skarn.Mining began in La Encantada during the 1950s with small vertical shafts, drifts and raises. It focuses on the high-grade silver zones using traditional hoists and extraction methods, before branching into two main separate mining camps: El Plomo and Penoles camp. Penoles, the previous owner, focused mainly on large ore bodies using post pillar cut-and-fill mining method to extract the higher-grade material. Due to the type of ground, irregularity of pillars, and rock conditions, large amounts of high-grade pillars had to be left in situ to ensure the stability of the excavations. The mined-out areas would then be filled with lower-grade material to assist in the stability of the secondary level. These room-and-pillar development entries were 2.5 m x 2.5 m (8.2 ft x 8.2 ft) and spaced every 10 m (32 ft), leaving a vertical pillar of 7.5 m (25 ft). First Majestic acquired La Encantada in 2006. After the acquisition of the mine, the company began the conversion of the surveying reference system from a local grid (Maria Isabel Shaft as 0,0) to the Nav27 coordinate system, and subsequently converted to the WGS84 coordinate system in 2015. Due to the extensive history of the mine, different areas were surveyed with different systems, causing significant challenges when designing the principal extraction levels, pillar heights and ramp locations. To overcome this difficulty, the entire mine was resurveyed and the old workings transposed to the new coordinate system, except for some inaccessible areas due to poor ground conditions or ground collapses. To further ensure pillar height and the safety of the mine workers, probe holes were drilled during the development process."

Sep 1, 2019

By Devin Burns, Saima Ghazal, Michael Owusu-Tweneboah, Kwame Awuah-Offei

Trust in AI systems and the nature and amount of information about the system can influence decision-making. It is, therefore, crucial to understand how AI-powered monitoring systems (e.g., gas monitoring systems) influence miners’ trust and decision-making in emergency evacuation. This work focused on measuring the differences between how participants respond to a simulated underground mine emergency evacuation situation when warnings are represented as coming from a human or AI-based monitoring system. We also manipulated the amount of information participants received about the system, yielding a 2×2 between-participants survey design. The participants received an alert message about rising gas levels in a mine and provided a response on how they would react and reported their perceived safety. We also asked questions to assess their trust in, preference for AI over human-based gas monitoring systems, and whether they are willing to delegate the duties of underground gas monitoring to AI systems. The experiment results show the amount of information had a significant influence on miners’ trust and decision-making. The safety perception of participants based on age, number of children and ethnicity was significantly different from one category to another. This work provides valuable insights as the mining industry deploys AI systems to aid mine safety.

Feb 1, 2025

By J. Weyer

"Colored gemstones are most often mined in small scale artisanal mining operations. Sri Lanka is well known as source for precious stones since thousands of years. Gemstones are mine in small open pits, directly in rivers (river dredging) and in underground mines. Almost all mined deposits are alluvial deposits. PRECIOUS STONES AND DEPOSITS Precious stones from Sri Lanka are well known for thousands of years. Tales and legends from Arabia, India, China and reports from discoverers like Marco Polo describe the fabulous stones from Ceylon which was the name for Sri Lanka before 1972. Already 1000 BC King Salomon got valuable gemstones from the legendary Queen of Sheba on her visit to Jerusalem. Paintings (frescoes) of the “cloud maidens” with huge gemstones can be seen at the “mirror walls” of the Sigiriya rock fortress - one of the eight World Heritages Sites of Sri Lanka.And even today some of the most valuable and most desired gemstones come from Sri Lanka. The term “Ceylon Sapphire” stands for an excellent royal blue color of high quality corundum from Sri Lanka. Reason enough to look a bit closer how these gemstones are mined. Sri Lanka has rich gemstone deposits which are mined underground, in small open pits or directly within a river. Some of the primary deposits in magmatic and metamorphic rock are also known, but most gemstones are mined in secondary alluvial deposits. Gem bearing deposits can be found in a band from NW to SE. Highly probable deposits and main mining areas can be found around Ratnapura – the city of gems, down to the coast (Matale) and up to the region around Elahera. These secondary deposits are mostly thin layers of gravel and sand, so called “illam”. The depth can vary between some dm to 10 25 m or even almost 40 m. But the average depth is about 12 m. Gemstone mining is controlled, licensed and regulated by a special authority – the National Gem and Jewelry Authority - which was founded in 1993. Another task of this authority is the promotion and development of the gemstone industry and the control of import and export of gemstones. Any violence of the NGJA law can lead to a fine or even up to 5 years imprisonment. To increase the confidence in the gemstone industry the Authority offers a unique service to foreigners. All bought gemstones can be tested free of charge in certain laboratories in Ratnapura and Colombo. So visitors can be sure they got no imitations, wrong stones or even synthetic stones or glass. It was said that detected synthetic stones will be destroyed and the seller will do all he can to replace the stone with the right stone. Otherwise he will lose his license."

Jan 1, 2016

By Ingunn Opland, Silje M. Tinderholt

Drill and blast project in Norway’s capital. The contract consists of 7 rock caverns (350–950 m2), 9.2 km tunnels, and four shafts. With 110 blue-collar and 31 white-collar, the project produces an average of 16–21,000 m3 hard rock per week, with a total of 19 tunnel faces. Weekly, nine grouting rounds for water control, 800 m3 shotcrete, and 1,200 bolts are required, and 60 trucks leave the site pr. day. Challenges include blasting in densely populated areas, planning and coordination to maintain high production, obtaining a CEEQUAL certification of very good, and transporting rock on Oslo’s main highway.

Jun 13, 2023

By W. M. Husslage

The permeability in the blast furnace shaft is adversely affected by low temperature reduction degradation of sinters. The fundamental cause is an expansion of the iron oxide phase resulting from reduction of hematite to magnetite. The present study showed that expansion behavior during the hematite / magnetite reduction step and the resulting microstructure are strongly influenced by the reduction temperature (viz. partial oxygen pressure), the reducing agent and the nature of the hematite. The reduction rate is of minor importance. A reduction mechanism is proposed, explaining the dilation behavior and the magnetite microstructure. The results can provide better insight into reduction degradation behavior.

Jan 1, 1998

By Wei Victor Liu, Na Zhang, Chengkai Fan, Bei Jiang

The truck haulage data from open-pit mine sites are usually massive and multidimensional with multi-peak Gaussian distributions. Artificial neural networks (ANNs) are well-known machine learning algorithms to handle massive and multidimensional data for building models. Moreover, Gaussian mixture modeling (GMM) is a suitable option for processing the data under multi-peak Gaussian distributions and improving model accuracy. For the first time, this study used a back propagation neural network (BPNN), an extreme learning machine (ELM), and a Bayesian regularized neural network (BRNN) coupled with GMM to deal with the complex truck haulage data and build three weighted ensemble models (WE-BPNN, WE-ELM, and WE-BRNN models) to predict truck productivity at mine sites. Decision tree (DT), random forest (RF), gradient boosting machine (GBM), and extreme gradient boosting (XGBoost) were used to build models to be compared with the weighted ensemble models. The results showed that the WE-BRNN had a higher accuracy than the WE-BPNN and WE-ELM models. The proposed weighted ensemble models performed better than the benchmark models in predicting truck productivity, indicating that a weighted ensemble approach based on the GMM analysis significantly improved the model accuracy. Based on the relative importance analysis, haul distance was the most crucial input variable for predicting truck productivity. This study provides a new approach to predicting truck productivity, which will help mining companies make sound budget decisions and improve mine planning.

Mar 2, 2023

By Qinghua Gu, BUQING XUE, XUEXIAN LI, JIANGSHAN SONG, Qian Wang

To solve the problem of time-consuming and low precision in updating the open-pit vehicle transportation network, a high precision road network model construction method for unmanned vehicles in open-pit mines is proposed. This method can be divided into two steps. In the first step, an improved deep learning image processing model named DeepLabv3 + C (DeepLabv3 + Concat) is presented. Then, the road information extracted by the DeepLabv3 + C network is used to construct a three-dimensional model of the open-pit mine road network. In the second step, aiming at the time-consuming problem of unmanned vehicle meeting in open-pit mines, a vehicle meeting strategy was proposed. This strategy is used to guide the navigation of unmanned vehicles in open-pit mines. Besides, the DeepLabv3 + C network is verified by comparing the mIOU (means Intersection Over Union), accuracy, and continuity of road image extraction with the mainstream networks. The road network model constructed in the first step is quantitatively analyzed, and its performance is compared with GPS trajectory clustering methods. At the end of the paper, vehicle running simulation is carried out on the road network model by using Unity (a 3D visualization simulation software). The results show that the road network model constructed by this method can meet the navigation requirements of unmanned vehicles in open-pit mines, and the feasibility of the vehicle meeting strategy is proved.

Jan 11, 2022

By R. L. Grayson, R. C. Althouse, L. A. Layne, M. J. Klishis

Introduction The researchers combine a detailed microanalysis of accident data and roof bolting field observations to develop new and meaningful risk indices for the roof bolter job classification. These indices incorporate information that has not been used in traditional measures of risk. The significant parameters that these new indices incorporate are the total number of accidents occurring within a particular work activity, the amount of time a miner usually spends performing the work activities in which the accidents occurred, and the average severity of the injuries incurred in the accidents. Being specific for a particular job, they aid comparisons among work tasks performed in the bolting cycle. The indices' specificity provide anew basis for reexamination of training and operational development of miners for specific jobs. Microanalysis The roof bolting microanalysis was performed by examining the empirical data and written summaries for all bolting accidents reported in the West Virginia Safety Information System (WVSIS) for the years 1983-1987. The WVSIS database contained more than 15,000 accident narratives. The microanalysis of bolting accidents covered 2083 reported personal injuries (RPIs). This large number of injuries, performed at an industry-wide level, provides a broad picture of the nature of roof bolting injuries. The analysis focuses on the activities associated with the cyclical routines of the roof bolting process. For this analysis, roof bolting tasks were categorized into work routines based on the sequence of work activities performed by roof bolters. Four work routines were identified within the overall bolting cycle. And these routines comprised 70% (1217) of all roof bolting accidents at the face. The routines include: face area preparation; tramming, positioning and setting the automated temporary roof support (ATRS); drilling holes; and installing bolts. The types of injuries most common within a routine and the average severity of those RPIs were also identified. Table 1 gives a breakdown of the percentage of accidents by the bolting routines. Another 19% of the roof bolting RPIs cannot be classified in a particular routine because of the vagueness of the narratives. However, it was clear that these accidents involved drilling holes or installing bolts. These results are consistent with previous research. It identified drilling and bolting, followed by tramming, as the most frequent sources of injuries (Helander, Krohn & Curtain, 1983). [Table 1-Accidents by bolting routines at the face Accidents Bolting routine Percent Number Face area preparation 18.2 222 Tram, position, ATRS 23.3 284 Drilling holes 34.2 416 Installing bolts 24.2 295 Total 1217] Roof bolter operators were involved in 82% (1706) of the 2083 accidents. The RPIs incurred by classified roof bolters occurred largely on working sections (95%) and at the face area on the working section (75%). Approximately 23% of the 1706 roof bolter RPIs occurred during tasks which were not part of the bolting cycle. These included belt utility work, providing supplies and section moves. Miners in other job classifications who were involved in roof bolting accidents accounted for the remaining 18% of the 2083 roof bolting RPIs. Among this group were section utility men and general laborers (41%), section machine operators (38%), and electricians and mechanics (11%). Another 9% were performing on-section supervisory functions. Face area preparation Face area preparation work led to a substantial number of injuries, although it accounted for the lowest number of injuries of the four routines. Several tasks were associated with the injuries incurred in this routine. Table 2 shows the percentage of injuries associated with face area preparation. [Table 2- Accidents occurring during face area preparation 26.6% Setting temporary and supplemental supports 24.8% Scaling roof and ribs 21.2% Installing ventilation devices 15.8% Handling supplies and materials 11.6% Miscellaneous tasks] The injuries commonly involved overexertion and 'struck by' falling coal and rock. Handling materials often led to overexertion injuries. Nearly 66% of the scaling-related injuries and about 33% of the injuries incurred during the setting of temporary supports involved 'strikes' by equipment, materials, top and rib. Tramming, positioning and setting the ATRS During tramming operations, workers were often struck by components of the machine and hit by loose roof and rib. Poor footing also led to slips, sometimes against the moving machinery. Table 3 gives a breakdown of accidents in this routine. Control levers were a significant problem in this routine.

Jan 1, 1993

By Yiming Zhang, Yunpeng Li, Chun Feng, Ruyang Cao

In the past, the selection of the number of empty holes between blast holes heavily relied on the subjective experience of practitioners, leading to unsatisfactory blasting results. The number of empty holes between blast holes is particularly important for the perforation of explosive cracks. In order to determine the optimum number of empty holes for inducing the propagation of explosive cracks, a two-dimensional numerical model of two-hole blasting was established based on the continuous-discontinuous element method (CDEM) using polymethyl methacrylate (PMMA) as the medium, and numerical simulation of various working conditions was conducted; the simulation results are basically consistent with the PMMA model test. Through the analysis of blasting parameters, the optimal number of empty holes with a certain hole spacing is fitted. The following conclusions are drawn: (1) There is a threshold for variable x. When x exceeds 50, the presence of empty holes cannot lead to the perforation of explosive cracks between the blast holes. (2) When x is below 50, the optimal number of empty holes inducing the propagation of explosive cracks can be determined through fitting an empirical formula. By adjusting the number of empty holes between blast holes, a significant spacing between adjacent blast holes was achieved, allowing for effective penetration, so as to effectively “induce” the direction of the fracture zone and make full use of the energy of explosives. The research results of this paper are conducive to the research of directional blasting technology and provide certain references for the optimization of precision blasting parameters.

Dec 19, 2023

"One of the major issues that the Rare Earth Elements Mining Industry has to deal with is the legislation vacuum that exists in many countries around the world. Among these, are countries which have long history and tradition in mining. In many cases the lack of direct legislation for REE mine management as well as for other potentially polluting industries can be a barrier to sustainable development. Moreover, the case of lax legislation in China has led to environmental pollution problems and extended smuggling of rare earth elements. This paper looks into the current regulatory status on the mining of REEs, identifies the loopholes and suggests some elements for a new global legislation framework for sustainable development in the REE mining industry. The setting of this regulatory framework will be in line with the present and future challenges of the rare earths market as well as with the policy strategies that are defined internationally. The aim of such a legislative framework will be to strengthen the global rare earth elements supply chain, appease social concerns and ensure the preservation and conservation of the environment. INTRODUCTION The general public received their first introduction to rare earth elements (REEs) in 2010, when the previously inconspicuous commodities became the subjects of front-page headlines. It was when China created a furore in global high-tech markets after imposing an embargo on Japan following a minor marine dispute (Barakos et al. 2015b). Soon enough the Chinese embargo was extended on REE export restrictions all over the world and thus aroused concerns to many countries over potential supply disruptions. The world had suddenly realized that these wonder materials underpin products that they care about. Governmental and industry executives, policymakers and material scientists voiced concerns and conducted numerous reports stating the situation and the risks of a supply crisis. The price spike of 2011 intensified the crisis and the public turmoil, yet the drama did not last for long as the prices declined significantly in 2012. Nevertheless, the world was nonplussed by the fact that China has the total control of the market with more or less the 90% of the global production. More potential entrants became interested, thus initiating an exploration boom during the recent years that has resulted in a significant increase in known global REE reserves that could have potentials for exploitation."

Jan 1, 2016

By Frederic Souche, Andrew R. Klaetsch, Brian Hann, Nick Goodenow

This paper describes support of excavation (SOE) design and construction for three large diameter shafts excavated through glacial soil and controlled blasting in complex sedimentary rock formations. SOE in soil consists of unreinforced secant pile rings designed to resist lateral pressure in circumferential compression, eliminating costly steel core beam reinforcing. Controlled blasting at the shafts, adits, and tunnels in densely populated neighborhoods requires managing risks to the public, buildings, and utilities. Controlled blasting approaches limited adverse impacts to receptors nearby while achieving adequate production and fragmentation. A site-specific observational approach was used to adjust blasting parameters, limiting the impact on local stakeholders while maintaining daily progress and managing overbreak.

Jun 13, 2023

By P. I. James, M. R. Baker

Este artículo analiza la nueva producción de cobre a partir de "minerales de desecho" de baja ley usando la tecnología de Blue Planet Strategies DEMET™ (Dynamic Electrode Mining Effluent Treatment, por sus siglas en inglés), que tiene como objetivo salvar la brecha de procesamiento entre la solución débil de lixiviación en operaciones de extracción por solventes/electrowinning (SX/EW), removiendo electroquímicamente los metales a partir de corrientes débiles y a la vez generando productos concentrados en metales objetivo en un análogo funcional de extracción por solventes (SX). Se estudió el tratamiento de la débil solución de lixiviación pregnant (PLS por sus siglas en inglés) y se usó para estimar los impactos económicos y de producción para una hipotética lixiviación en pilas de cobre brownfield y una operación aumentada DEMET usando SX/EW para tratar el "mineral de desecho." Se presenta la remoción de cobre a un 86% de eficiencia en las placas por debajo de 0,1 g/L de cobre con un consumo de energía de 0.55 kWh/lb de cobre y una concentración del producto mayor a 10 g Cu/L. El modelamiento arrojó aproximadamente $2/ lb para la producción total de cobre y costos de tratamiento menores o iguales a $1/lb con un inmediato aumento del margen bruto de operación del 12% para el brownfield incrementado. Se indicó también un aumento de la vida de la mina con un margen bruto promedio de 38% en la producción aumentada de "mineral de desecho" con valores de cobre de $3.25/lb.

Jan 1, 2014

By James H. Allen

The air lift method of pumping water is discussed. A review of several large diameter hole drilling projects that used reverse circulation air lift techniques is presented. Proposals are made for reverse circulation flow rates for slow rates of bit penetration (5 fph) as well as reverse circulation flow rates for faster rates of bit penetration (10 fph). The Ingersoll- Rand air lift equations are modified for rotary drilling operations. By establishing minimum reverse circulation flow rates and utilizing the modified air lift equations, the establishment of minimum circulation equipment sizes and a more definitive requirement for improved bit body design should result.

Jan 1, 1976

By Michael Murphy, Gamal Rashed, Brent Slaker

Pillar stability continues to be a significant concern in multiple-level mining conditions, particularly for deep mines when pillars are not stacked or the thickness of interburden between mining levels is thin. The National Institute for Occupational Safety and Health (NIOSH) is currently conducting research to investigate the stability of pillars in multiple-level limestone mines. In this study, FLAC3D models were created to investigate the effect of interburden thickness, the degree of pillar offset between mining levels, and in situ stress conditions on pillar stability at various depths of cover. The FLAC3D models were validated through in situ monitoring that was conducted at a multiple-level stone mine. The critical interburden thickness required to minimize the interaction between the mining levels on top-level pillar stability was explored, where the top level mine was developed first followed by the bottom level mine. The model results showed that there is an interaction between numerous factors that control the stability of pillars in multiple- level conditions. A combination of these factors may lead to various degrees of pillar instabilities. The highest degree of local pillar instability occurred when pillar overlap ranges between 10 and 70%. On the contrary, the highest degree of stability occurs when the pillars are stacked, the underlying assumption is that the interburden between mining levels is elastic (never fails). Generally, for depths of cover investigated in this study, the stability of top-level pillars shallower than 100 m (328 ft) or with interburden thicknesses greater than 1.33 times the roof span—16 m (52.4 ft) in this study—does not appear significantly impacted by pillar offset. The results of this study improve understanding of multiple-level interactions and advances the ultimate goal of reducing the risk of pillar instability in underground stone mines.

Jul 27, 2022

By John W. Sweeney

Florida is usually thought of as a vacation State, not a mining State, yet Florida has been the leading producer of phosphate rock in the United States for 85 consecutive years and in 1978 supplied over 80 percent of the national output and over 30 percent of the world's output. It is estimated that the Central and South Florida phosphates contain 412,800 short tons (374,000 metric tons) of U308, that 115,000 short tons (104,000 metric tons) of U308 will be contained in the wet-process phosphoric" acid procsssed in the United States through the year 2000, and that 54,000 short tons (49,000 metric tons) of U308 will be available from Florida. In 1978, two companies in Florida and one in Louisiana went on-stream recovering uranium oxide from wet-process phosphoric acid and three others started construction of U308 extraction facilities. These six companies will have the capacity to recover 2,137 short tons (1,900 metric tons) of U308 annually in 1980, which will account for about 15 percent of our domestic requirements.

Jan 1, 1979

By Piyush Rai, Suresh Kumar Sharma, Punit Paurush

The present study has been conducted in surface limestone mine to select the controllable blasting design parameters affecting the peak particle velocity (PPV) for assessment of ground vibration. The study aims at using two prominent statistical tools, namely, principal component analysis (PCA) and stepwise selection and elimination (SSE) techniques for identifying the key controllable parameters affecting the PPV. For determining the correlation coefficient between blasting design parameters and PPV from 44 field scale trial blasts, multi-variate linear regression (MLR) technique was done. It was found that the PCA and SSE eliminated a huge number of controllable parameters to identify the most important parameters, affecting the PPV. The PCA eliminated 6 number of parameters while SSE eliminated 5 number of parameters, and the coefficients of determination (R2) obtained were 0.616 and 0.584 for PCA and SSE respectively. The predictor equations were evolved, and these equations were used to validate the PPV results for another set of 21 field scale trial blasts. The predictor equations have been found to be fairly accurate in predicting the PPV values. Further, the PCA technique provides very near prediction of PPV with high degree of correlation in comparison to SSE technique. The paper highlights the role of state-of-art statistical tools in selecting the blasting design parameters affecting the PPV in field-scale blasting.

Mar 1, 2021

By Innocent John Arinze, Chidubem Okwudiri Emedo

This contribution presents the first multi-scale geophysical investigation conducted in the Abakaliki and Obubra mining districts (AOMD), southeastern Nigeria, for the exploration of shallowly emplaced (< 50 m) massive sulfide and barite mineral deposits. Raw airborne magnetic data covering the AOMD was acquired and subjected to diverse enhancement routines to facilitate the identification of areas of subtle magnetic anomalies for subsequent ground truthing. The mineralization is mainly made up of galena, sphalerite, and barite. The contrasting physical properties between these minerals and their host rocks make resistivity, induced polarization (IP), spontaneous potential (SP), and magnetic methods ideal to study and delineate the mineralization and possibly locate the ore bodies. Wenner DC resistivity and IP data acquired along the same parallel traverses are inverted using Res2dinv to produce 2D tomography models of resistivity and chargeability. The resistivity and IP models were successful in delineating zones of sulfide and barite mineralization. The ground SP data collected along the same traverses as the resistivity and IP data were interpreted as line graphs. The 1D SP models show a number of central negative anomalies that could be related to sulfide mineralization. These anomalies show fair-to-good spatial continuity and are in close agreement with the result obtained in the resistivity and chargeability model. This study suggests the presence of exploitable mineral deposits in the AOMD and demonstrates the superior interpretative ability of combined geophysical methods over a single geophysical approach.

Oct 20, 2020