Search Documents

By B. P. Boisen

INTRODUCTION The rapidity of onset, rate of increase, and magni¬tude of loads in an underground support system can be measured using load cells or pressure cells, whichever is appropriate to the type of support. These instruments should be installed at the various instrumented station locations immediately after excavation. If the loading of a member is of interest, the load should be measured, whereas if the deflection or strain of a member is of interest, the strain should be mea¬sured. It makes as little sense to use a load cell to allow computation of strain as it does to measure the strain and then back calculate the load. Tunnel steel set de¬signers today invariably rely on the early work of Karl Terzaghi, the basis for which is load, so load measure¬ment should be the main concern. The current trend of using strain gages on steel sup¬port systems stems from the inability by some to eval¬uate unusual loading conditions caused by uneven block¬ing. In fact, uneven blocking will obscure almost any attempt (whether with load cells or strain gages) to properly evaluate support performance. The load curve in Fig. I shows the development of a characteristic early peak load sometimes called the "rear abutment load" seen in many underground open¬ings. It is thought that the peak reflects the coupling of the rock and the support system, and that the magnitude will increase until some yielding, or minor failure, of the support system occurs. At that time, the slight deforma¬tion of the support system promotes the formation of minute shears in the opening walls, and these shears tend to distribute stress between the support system and the adjacent rock in proportion to the relative rigidity of the support elements and the rock. In normal rock, as a result of this stress redistribu¬tion, subsequent load magnitudes generally do not reach the magnitude of the early peak load. In physically unstable (squeezing) or chemically un¬stable (swelling) rock, however, the loads experienced after passage of the early peak load may in fact show a slow, continuous increase. One of the very important purposes of load instrumentation is to provide the means for recognizing such long-term adverse trends, thus enabling the proper remedial steps to be taken. Another purpose of load instrumentation is to pro¬vide a comparison between the magnitudes of the early peak load and the subsequent stable load. The ratio of these two loads is analogous to a safety factor, and may be used to evaluate the efficiency and economy of the support system design. Aside from considerations of economy, it may be well to design support systems which do not have excessively high ratios of early peak load to subsequent stable load. Should these ratios be exces¬sively high, the support system may be so rigid that the yield or failure associated with stress redistribution may occur with explosive violence. Load cells for use in mines, tunnels, and on con¬struction projects come in many forms. Almost all, however, employ the same procedures for installation, readout, etc. Therefore the following comments are almost universal in application. LOAD CELL INSTALLATION Load cells should be installed with bases parallel to the surfaces against which they bear. Care must be taken to orient the cells so that their signal cables are protected from accidental damage as a result of con¬struction, maintenance, or cleanup activities. Most electronic load cells are compensated for tem¬perature variations likely to be encountered during nor¬mal operations. However, if a large difference is an¬ticipated between the calibration temperature [21°C (70°F)] and the average operating temperature, the cells should be conditioned to the operating temperature for at least 8 hr prior to installation. This is to insure that the initial reading, made under no-load conditions prior to installation, provides a stable value to which subse¬quent measurements can be referred. Hydraulic load cells tend to be temperature sensitive and should be used with that in mind. Also, hydraulic load cells tend to be soft compared to electronic types and will sometimes allow movement to take place in a system intended to be semirigid. Furthermore, hydrau¬lic load cells tend to be difficult to read remotely. Care must be taken to use bearing plates on both sides of load cells which are sufficiently rigid and of high enough bearing capacity to prevent bending and crush¬ing under load. This is very important with tieback load cells (basically a ring of steel) which can easily dig into bearing plates. MAINTENANCE AND TROUBLESHOOTING Except for a direct hit by a miner's axe or flyrock from a blast, most hydraulic load cells are nearly in¬destructible and require little, if any, maintenance. Hy¬draulic oil on the bearing plates is a good indication of a leak and the need for corrective action. Field maintenance of electronic load cells involves protecting the instrument and signal cable from mechani¬cal damage and from unnecessary exposure to dirt and moisture, and recognizing and correcting damage and the effects of normal wear and tear.

Jan 1, 1982

By Stuart R. Cotterill, Jack D. Nelmark

Introduction Opencast surface mining requires blasthole drilling to achieve mine planning. No single method of mining is right for all conditions. Occasionally, mine planners introduce a project with little regard to drilling and blasting. These costs are usually a significant percentage of total mine overhead. One drilling and blasting method that can be used to reduce overall mine expense is inclined or angle hole drilling. But inclined-hole drilling will not cut costs unless a set of required circumstances is met. Several conditions of mine design indicate the use of angle drilling. Geotechnical problems must first be analyzed. Primary considerations are safety, fragmentation, production, and maintenance. Secondary considerations are, in some instances, reduction in amount of explosives, which lowers blasting costs; reduction of practical fragmentation beyond blasting pattern limits; and reductions in overall costs due to reduced volume of excavation. Future trends in blasthole drilling may include incorporation of drill equipment designed to allow rapid change from vertical to inclined drilling. This will allow the operator to adapt to changing hole requirements with minimal production loss. Another improvement may be the ability to chamber holes at any elevation throughout the hole depth. This will allow more charge to be placed at strategic locations to improve fragmentation. Merits of Drilling Inclined Holes Drilling is performed to create voids for explosives. It is done either to recover minerals or to excavate a volume of earth. The manner of mining or excavation can greatly affect the economics of the overall project. Many innovations and methods have been tried, but the most practical and economical is still drilling holes and using explosives to fragment the material. To break up the material, the practice has been to place charges within the mass. This is done by drilling holes of a specific diameter and depth into the material. The holes are of such magnitude as to develop sufficient energy to break or loosen this material, providing for easier removal. In general, more open or exposed faces must exist to aid material breakage when blasting. Inclined drilling can be advantageous in open-cut mining with highwall depths of at least 24 m (80 ft). A minimum of two faces are open in open-cut mining and the material can be thrown outward to cover pre-mined volume. This cuts cost by eliminating the need to remove or relocate a large portion of material. Sometimes the material is of such a mass that more energy per unit is required to loosen it than can easily be done by blasting vertically. Inclined holes allow a more uniform loading of drilled holes. The unit of energy is raised, so little or no secondary blasting is required. This usually comes about only if the main plan calls for drilling holes deeper than 24 m (80 ft). For shallow holes, spacing and burden can be made closer to allow sufficient energy to blast the toe. If the open face is in only one

Jan 9, 1984

By Thomas J. DeMull

Heap leaching was introduced to the precious metals mining industry approximately two decades ago as a simple, low cost method for recovering gold and silver from ores. Since that time, operational experience has contributed to knowledge and understanding of the process, making it a reliable alternative to conventional milling processes for low grade ores. At time of this writing, dozens of heap leach operations are active producing hundreds of thousands of ounces of gold and millions of ounces of silver annually. These successes have caused the popular press to acclaim heap leaching "high-tech" gold mining, but, despite the hype, the process remains a simple one. An example of simplicity in heap leaching is the operation established in 1986 at Amax Gold's Sleeper Mine. Starting with a simple goal, namely to produce gold from sub-mill grade ore at low cost, heap leaching was rapidly implemented at Sleeper; only five months after testwork started, leaching commenced on the first commercial scale, 50,000 ton heap of low grade ore. Sized at 600,000 tons per year to produce 10,500 oz gold per year, the low grade heap operation has performed beyond expectations. During the first year of production, 881,800 tons have been leached producing 15,665 oz of gold and 35,528 oz of silver. Operating ·costs for the first year have averaged $112 per oz gold produced ( or $95 per oz if silver credit is included). Successful implementation of heap leaching at Sleeper has had a dramatic impact on ore reserves and future operations.

Jan 1, 1998

By A. L. Putz, G. Ladouceur, A. R. Laplante

A laboratory centrifugal concentrator was used to evaluate two gravity circuit configurations treating a flash flotation concentrate at a Canadian gold mill. The Initial circuit consisted of a 76 cm (30 Inch) plant Knelson Concentrator (PKC) for coarse gold removal. Later, a hydroseparator and spiral were Installed, with the hydroseparator underflow feeding the spiral and the spiral tailings plus hydroseparator overfiow reporting to a 51 cm (20 Inch) PKC. Gold recovery In the 76 cm PKC averaged 45%. Gold was recovered consistently In all size fractions greater than 38 µm, where recovery dropped to 22% for the -38 µm material. Changing the circuit to Include the hydroseparator and spiral decreased the Knelson unit recovery to less than 17%. The decrease was attributed to the spiral which recovered much of the free gold ahead of the Knelson and to changes In the mill feed (free gold portions were finer and less abundant). The spiral demonstrated erratic behaviour although It still recovered significant coarse gold (+75 µm) yielding unit recoveries of 18-44%. Although mechanical difficulties were experienced with the 76 cm PKC, Its performance was superior to that of the hydroseparator, spiral and 51 cm PKC configuration. Much of the gold In the ball mill recirculating load was found to be too coarse for significant recovery In the flash flotation cell and should be recovered by gravity from the cyclone underflow or ball mill discharge. The LKC proved to be a successful device to evaluate gravity recoverable gold content. Dilution of test samples with silica further enhanced this methodology.

Jan 1, 1993

By W. White

The manuscript of this paper was not available for publication when the Proceedings went to press. Should the author elect, he may distribute copies at the time of the Symposium.

Jan 1, 1986

By Ananda M. Wijesinghe

The manuscript of this paper was not available for publication when the Proceedings went to press. Should the author elect, he may distribute copies at the time of the Symposium.

Jan 1, 1986

By J. Pang

The mechanisms of chalcopyrite oxidation in alkaline solutions have been studied using cyclic voltammetry and AC impedance spectroscopy techniques. Analysis of the impedance spectra using equivalent circuit models has made it possible to suggest layerwise growth of surface films. From the value of equivalent circuit parameters, properties of the surface layers are inferred. These properties change substantially with the change in oxygen and/or collector concentration in solution and give rise to changes In contact angle and flotation response. In agreement with prior investigations, the present study shows that flotation recoveries alone cannot be used to determine the effect of collector on flotation of chalcopyrite. The rate of flotation is a more sensitive parameter to determine the role of collector on floatability of chalcopyrite.

Jan 1, 1989

By S. S. Peng

An expert team consisting of geology, civil, and mining engineer professors was organized to investigate several problems of longwall mining in three mine sites including: site investigation, panel layout and support selection, overburden strata movement, surface subsidence and structural damages, slope, stability, well and stream dewatering, etc. The results include the development of a PC software package such as powered support selection, Surface subsidence prediction, optimum panel dimension, and pillar design.

Jan 1, 1989

By N. Magdalinovic

This paper analyzes the basic elements important for sustainable development in the sphere of metal mineral raw materials and offers one of the possible ways of defining the index of sustainable development.

Jan 1, 2007

By Terrence D. Chatwin, James Hendrix

Based on the findings within their report to Congress, the US Environmental Protection Agency (EPA) announced that it had decided not to regulate mining wastes under the hazardous waste regulatory program. However, they found that some mining wastes are hazardous and may be causing environmental damage. Cyanide wastes from heap leach operations were included in this group. In evaluating the effects of cyanide use in mining one finds a significant lack of information on the fate of cyanide in soils. Cyanide attenuation and degradation of soils is important, because ground water is a major potential pathway for cyanide contamination. There is a strong potential for cyanide to be removed from solutions as it migrates through soils· by volatilization, chemical reaction, adsorption, oxidation and biological processes, but no definitive investigation has defined these mechanisms adequately to be able to predict the fate of cyanide in soils.

Jan 1, 1998

By V. Arad, S. Arad

Besides the conservation and closing activities, an important issue to achieve is the environmental rehabilitation of the mining perimeters, also assuring the continuity and sustainable development of the mining activity in the Jiu Valley. Modifying and depleting the soils by mining works and dumps of mineral waste as a result of coal mining and tailing is one of the important aspects. The paper’s aim is to analyze which are minerals and resources policies of our government and to adopt measures for sustainable development in the coal mining in this region. The measures to reduce the instability risk for the mining works and waste dumps, which could affect the underground mining constructions or the related surface areas, were consider. It is most important to establish the priorities in order to obtain a high efficiency by combining the measures according to the environmental analysis and risk assessment.

Jan 1, 2005

By H. J. Handewith, W. D. Coski

This paper describes the development and testing of the RAMEX excavation system. Incorporating a synergy of low velocity, high energy impact and kerf cutting, this machine offers a competitive alternative to drilling and blasting in hard rock. It is a boom mining machine that incorporates the features of a lightweight roadheader and it can mine nearly any shape opening in hard rock. The RAMEX Tunneler has been developed to satisfy industry demands for a non-explosive, flexible, continuous and rapid underground rock excavation system. It will produce minimum ground vibration in the urban environment and allow the flexibility necessary for thin seam mining conditions. It will also reduce initial ground support costs and has a minimum impact on rock integrity. Developed by RAMEX Systems with cooperative research provided by the U.S. Bureau of Mines, this system, could produce the next step in the continuing evolution of mechanical mining systems.

Jan 1, 1989

By David J. Kruse

Although it may be perfectly acceptable to neglect the belt's elastic behavior for many conveyor designs, this can lead to disastrous consequences for others. So how can a designer know in advance if a dynamic analysis is required? Unfortunately, in many cases it is impossible to foresee or predict dynamic problems prior to performing the actual analysis. However, a basic understanding of the principles of conveyor dynamics, as well as knowledge regarding common problem areas, can significantly help the designer make more educated decisions during the initial design stage. This paper will demonstrate how static calculations alone can incorrectly represent the true behavior of the conveyor system. It will also discuss the importance of correctly sizing and locating the take-up system to provide the most economical conveyor design. The use of capstans will also be discussed followed by two examples demonstrating their proper operation.

Jan 1, 2002

By H. A. Kortmann

Blast furnace operators have been steadily increasing their quality requirements on burden material. These requirements include a high reduction rate of the ore burden as well as good strength at the beginning and during the whole blast furnace operation. Special requirements are made on the softening and melting behavior which ensures an optimal formation of the cohesive zone in the blast furnace. On the whole, the self-fluxed and olivine-based pellets meet these higher requirements due to their chemical composition, especially in the pure pellet operation. In the mixed sinter/pellet operation partly-fluxed and acid iron ore pellets can be appropriately used. The paper describes the demands on, and characteristics of, different kinds of pellets used in the Federal Republic of Germany.

Jan 1, 1989

By F. Kennedy

Consolidation Coal Company (Consol) supports an active R&D effort to improve the safe, productive mining of coal and to utilize coal in an environmentally acceptable manner. Attention will be focused on degasification of coal seams, continuous coal transport systems, earth sciences activities, and coal combustion. Brief mention will be made regarding the SO2 emissions control programs. The research program constitutes about 1.0% of Consol coal sales which positions Consol as the preeminent coal company supporting broad-based research addressing the full spectrum of the various problems associated with utilizing the nation's abundant reserves of economical, readily available fuel.

Jan 1, 1989

By M. Gershon

Four computerized approaches for coal blending are described and their strengths and weaknesses are explored. Spreadsheet analysis Other than word processing, spreadsheet software is the most commonly used software. Its wide availability and ease of use are two desirable features that have led many to try to adapt it to the purpose of coal blending. These are the two main advantages of this approach. To use a spreadsheet for coal blending, each row of data represents one source of coal. Each column represents a quality of the coal, with the last column specifying the tonnage of that coal in the blend. The calculated figures are the blended qualities, which can be programmed to appear in the bottom row. A trial-and-error approach is then used to develop the best blend. Inserting any blend in the last column provides the blend characteristics at the bottom of the page. If any specifications are not met, the blend can be changed, all calculations being immediately updated. This process is repeated until all specifications are satisfied. A third advantage of this method is that it is exactly the procedure that one would go through if doing this by hand. With a spreadsheet, many more blends can be evaluated in much less time, allowing the designer to try to improve over satisfactory blends to find the best of them. The resulting improved blends or cost savings are a fourth advantage of this approach. There is only one major disadvantage of using the spread-sheet. This is that most probably the best blend is not found. As an inexpensive introduction to computer-assisted blending, which can be easily understood and cost just a few hundred dollars, this is a recommended place to begin. Computerized search Computerized search approaches represent crude first attempts at letting the computer design the blend. Unfortunately, the blends found by these programs are very often less satisfactory than those developed manually. The way these techniques work is that they design, according to some predesigned pattern, a number of different blends and then quickly evaluate them. It is then straightforward to select the best from this sample set. The quality of the results depends on the number of blends designed, the way they differ from each other (the search procedure), the number of sources available, the number of quality specifications, and the severity of the specification limits. Good results are usually obtained for small, simple problems. At best, the results obtained are inconsistent from one blend to the next. Programs of this type are advertised in the mining literature. They usually mention how many different blends are evaluated, making it clear that this is more than can be tried manually. Expert systems Expert systems use a source of information known as a knowledge base. The knowledge base, usually a set of if-then rules, attempts to reconstruct the deductive reasoning process of an expert in some job capacity. For coal blending, the usual trial-and-error process has an easily recognized pattern of rules that are followed to try to find a better blend. By following these rules, it is possible to home in on the best blend without the exhaustive search required by the previous method and without the manual manipulation of the spreadsheet approach. The use of an expert system accomplishes this. One of the rules may say something like "if BTU is out of spec, then add more in the blend from a source having a high BTU and subtract some from a source having low BTU." In other words, it goes through the trial-and-error process. The process continues until all specifications are achieved and can continue further to try to optimize the cost. Of course, less simplistic rules are also needed. One set of rules would determine maximum changes in the tonnage added or deleted to the blend or from any one source. Other rules would be needed to determine which quality to improve if two or more are out of spec. At this level, the process of building the knowledge base provides the engineer with a deeper understanding of his or her own thought processes. The advantage of obtaining better blends is clear for this approach. Two more advantages should also be apparent. One is that it follows the same common sense logic that is used when doing the blends by hand or by spreadsheet, making it easy to understand. The other is that, like the search procedure, it designs the blend rather than just analyzing manually designed blends. Thus, it has all the good features of both approaches discussed thus far while providing improved results over each. A final advantage is the ease of use and ease of development. The expert system shells that are on the market are very easy to use and can be run on microcomputers. Linear programming Linear programming is an algebraic tool that solves a set of linear equations to yield an optimal solution to a problem. The optimal solution is based on the linear model so the results are only as good as the ability of the linear model to accurately portray the reality of the problem situation. It is fortunate for the coal blending problem that a linear model can be devel¬oped that reflects exactly the problem that is required. Unfortunately, the mining industry has been slow to use this tool. Coal blending applications available that use linear programming take one of three forms. The first, requiring exper-

Jan 12, 1988

By Mark L. Mott, Michael P. Synder

The Mine Safety and Health Administration has developed a program to improve the decision making process of personnel involved in mine emergency situations. The Mine Emergency Responsiveness Development Program (MERD) has been designed specifically for fires and explosions in underground mines. This program addresses the responsibilities and organizational requirements that are necessary during rescue and recovery operations of a mine emergency . Specific skills and knowledge are required to manage an organization of personnel under conditions of intense stress, such as a mine fire or explosion. As a result, the MERD program develops these skills by providing role playing emergency simulations. This role playing provides the participants with the opportunity to experience problems, explore solutions and interact with other personalities which may exist during mine emergency situations. This paper presents the standard procedures for the MERD program developed by the Ventilation Division of the Pittsburgh Health Technology Center.

Jan 1, 1991

By A. Russell, M. N. Hughes, Jack Barrett

The bacterial oxidation of arsenopyrite has been shown to be an efficient, economic and environmentally acceptable method for the liberation of any gold content . The mechanism of the process is not certain but is usually considered to involve direct and indirect reactions with respect to bacterial involvement. The direct reactions are those in which the bacteria attached to the mineral surface cause its dissolution, with dioxygen being the oxidant. The iron(III) produced in solution is the chemical oxidant in the so-called indirect reactions. Barrett et al 2 showed that a synthetic bio-oxidation solution (with no cells present) could dissolve up to 15% of an arsenopyrite sample, the products of the chemical oxidation being iron(II) and arsenic(III). This paper describes an extension of the investigation of the chemical process and its imp! ication for the mechanism of the bio-oxidation of arsenopyrite.

Jan 1, 1990

By Hugh K. Herbert, R. John Watling

Laser Ablation-Inductively Coupled Plasma-Mass Spectrom­etry (LA-ICP-MS) has been used successfully to "fingerprint" gold in forensic investigations within Australia and abroad. By comparison of the elemental associations it has been possible to relate gold to specific mineralising events, mines, bullion samples and fabricated articles. The methodology facilitates identification of the provenance of gold thereby providing definitive scientific evidence in criminal investigations. "Gold" samples for analysis span a wide range of materials with many requiring exhaustive prior separation and treatment to present the contained gold in a chemically "unmodified" state, and in a form, suitable for LA-ICP-MS fingerprinting. The quality of the fingerprint, and hence its value in evidence, is directly related to the rigours of prior sample preparation and evaluation, to an appreciation of the history of the gold under investigation, and to the skill of the analyst.

Jan 1, 1995

By Jan M. Mutmansky

The application of computers and operations research to mine planning problems has changed and progressed significantly over the last several decades with a continuing growth and increased breadth of applications being quite evident. A scan of the volume associated with the 1969 APCOM published two decades ago (Weiss, 1969) indicates that the primary applications in mining were often in the areas of short-term and long-term planning and production scheduling. The applications at that time were oriented toward underground and surface mining, but block and other mine sequencing and scheduling problems for large open pit mines were perhaps the most popular target for the operations research approach. A variety of operations research techniques were used at that time with heuristic models, mathematical programming models and simulation programs all being commonplace. The computers used were usually mainframe models which were of ten shared by accounting, engineering, planning and research groups.

Jan 1, 1989