Search Documents

By R. C. Ford, J. Kelsey, S. A. Pierce, M. D. Ankeny

Evaluation of acid drainage risk from spent (leached) ore in arid climatic zones consists of two components: (1) whether residual and secondary minerals will release acid and metals when exposed to rainfall, and (2) whether ambient rainfall is likely to infiltrate, and eventually impact surface or ground water resources. The risk of acid drainage from spent ore at the El Abra on-off copper leach pad operation was evaluated using conventional geochemical methods and unsaturated flow models. Although geochemical testing indicated poor quality water would result from any seepage, unsaturated flow modeling demonstrated that infiltration and seepage were unlikely given the arid climatic conditions. Modeling further demonstrated that the residual moisture content of the spent ore when it is removed from the leach pad controls the risk of seepage. To further reduce the risk of seepage, operational controls were developed and implemented at the El Abra site.

Jan 1, 2000

By C. P. Lazzara, F. J. Perzak, C. C. Hwang, C. D. Litton

Fire development and spread along conveyor belts in ventilated ducts were investigated experimentally and theoretically. Various types of conveyor belts used in mining applications were ignited and burned in a full-scale gallery under various flow conditions. The flame spread rates depended strongly on the ventilation air speed. The time-temperature traces of gas and belt obtained at 12 feet from the entrance show that a rapid belt surface temperature change takes place prior to a change in the gas temperature, indicating that radiative heat transfer from the flame to the belt surface plays an important role. Further, anomalies in the flame spread rate in the vicinity of 1.5 m/s air speed (i.e., much greater rate than that observed at either higher or lower speeds) can be explained through the mechanism of flame tilt and the resultant view factor between the flame surface and the belt surface. In order to correlate the fire spread with material properties of the conveyor belts (such as the specific heat, the thermal conductivity, and the pyrolysis temperature) and the fire environment (such as the gas temperature and the ventilation air speed), a theoretical model has been developed. This model is based on the experimental observation that the radiative heat transfer is the dominant mode of energy transfer ahead of the flame front. Agreement between the theory and the experimental results is good.

Jan 1, 1991

By Por J. B. Evans

El mantener un beneficio óptimo sobre todo el conjunto de un emplazamiento minero necesita una constante puesta al día de las estrategias operativas. En esencia, cada estrategia es una combinación particular del gasto del capital previsto, el flujo de ingresos y el tiempo transcurrido. La selección de una estrategia basada en el beneficio potencial requiere que cada estrategia contemplada con un ordenador, un análisis tal puede ser engorroso. Este capítulo discute o desarrolla una técnica de "corte rápido" que asigna una relación de beneficio a las estrategias alternativas e identifica aquellos aspectos de una estrategia que producen mayor impacto sobre el beneficio. Esta técnica puede proporcionar valoraciones rápidas de suficiente precision para muchas de las decisiones de las estrategias operativas que se toman sobre la marcha en minas que se encuentran en explotación.

Jan 1, 1982

By G. Mbuyi Kamba

Literature is rather abundant on the topic of steady-state network analysis programs. Many versions exist, some of them have real extended facilities such as full graphical manipulation, fire simulation in motion, etc. These programs are certainly of great help to any ventilation planning and often assist the ventilation engineer in his operational decision making. However, what ever the efficiency of the calculation algorithms might be, their weak point still is the overall validity of the model. This numerical model, apart from maybe the questionable application of some physical laws, depends directly on the quality of the data used to identify its most influencing parameters such as the passive (resistance) or active (fan) characteristic of each of the branches in the network. Considering the non-linear character of the problem and the great number of variables involved, finding the closest numerical model of a real mine ventilation network is without any doubt a very difficult problem. This problem, often referred to as the parameter adjustment problem, is in almost every practical case solved on an experimental and "feeling" basis. Only a few papers put forward a mathematical solution based on a least square approach as the best fit criterion. The aim of this paper is to examine the possibility to apply the well-known simplex method to this problem. The performance of this method and its capability to reach the global optimum which corresponds to the best fit is discussed and compared to that of other methods.

Jan 1, 1995

By F. Habashi

It has been estimated that about 45 tonnes of mercury are emitted annually in the USA in the atmosphere as a result of burning coal in power-generating plants. A similar situation had existed in the metallurgical industry particularly in zinc production plants but this problem has been solved long ago by introducing scrubbing systems. Methods of mercury removal and recovery are discussed.

Jan 1, 2010

By J. Alton Burks, Roy C. Bartholomae

The chain conveyor is utilized extensively in underground mining to convey raw ore, especially coal. It is estimated that several thousand loading and continuous mining machines rely on this type of conveyance. Although the chain conveyor is both efficient and highly reliable, its use is generally associated with the production of noise levels that often exceed 105 dBA at the operator's position. Thus, it is one of the most significant contributors to the occupational noise problem experienced by miners in the underground coal mining environment. Conventional engineering noise controls that result in an average reduction of 4 dBA have been previously designed and implemented. However, a novel solution involving a change in conveyor operation has been proposed that takes advantage of two aspects of conveyor noise: 1) conveyor noise has an approximately cubic dependence on conveyor chain speed and 2) due to the damping provided by coal, a full conveyor is 5 dBA quieter than an empty one. An engineering analysis has shown that a significant reduction in the operating noise level of a typical continuous miner can be achieved through the use of an adjustable speed drive automatically controlled by a coal loading sensor that maintains a full conveyor at all times. The potential reduction depends primarily on the mining conditions (coal seam thickness and the presence of either rock or water) and varies from 7-18 dBA. Other benefits to be derived from the use of a variable speed drive include reductions in power consumption, dust, and maintenance costs.

Jan 1, 1992

By John Marsden, John Mansanti, Jim Arnold, Mike Gleason

DOUG HALBE: We're not quite to the end of our session, but we're close. We've had a lot of fun with some of these spill ideas. But these are serious problems, and I think we might be able to benefit by continuing to compile these. Several years ago, the metallurgists at the various operations of Gold Fields Mining Company had a newsletter that came out every two months for several years. This publication consisted of short articles by the staff at the various operations, plus a few others, on problems they'd had and how they solved them. One very useful article, "Things We'd Have Done Differently at Chimney Creek," was written shortly after start-up. John Marsden was the editor and John Mansanti contributed to it, as did Jim Arnold (our distinguished co-chair) and Mike Gleason. I would be interested, with the permission of the audience, in editing that article to make it a little bit less abrasive and putting it into the record here. I think it's a useful SME function to maintain a list of things we've done wrong in plant design, things we don't want to do again. If we have another open session in the future, would others be willing, even anonymously, to contribute, bring slides, and say "Hey, look at the goofs we made?" [laughter, followed by support from the audience] Okay, we'll plan on that. And we'll try to include the Chimney Creek list in the transcript of this session-perhaps edited a bit.

Jan 1, 1998

By Richard E. Hucko

The U.S. Department of Energy (DOE) Coal Preparation Program focuses on providing the technical and process-development basis that can be utilized to produce environmentally acceptable clean-coal feedstocks for use as market conditions permit. A major objective of the Coal Preparation Program is the development of physical coal-cleaning technologies capable of significant removal of mineral matter and pyritic sulfur at high energy recovery levels.

Jan 1, 1989

By G. G. Marino

Little comprehensive information has been reported on the behavior of room-and-pillar mines. The objective of this paper is to present case data on mine failures in the Illinois basin for use in practice. Presented are results of an ongoing study and details on the site characteristics of cases where sags have developed on the surface. Site data are reported to show the geologic, mining, and sag conditions that existed. Sags mainly develop from pillar, floor, or pillar-floor failure. The character of the sags depends upon the type of mine failure as well as the overburden response.

Jan 1, 1989

By G. E. Wasson

Coal in most refuse ponds including those owned by Consolidation Coal Company can be recovered by froth flotation techniques. Laboratory studies show that the flotation conditions required for coal recovery varied greatly from pond to pond. The variables found to be most important for high coal recovery and low product ash were: a) the amount and type of flotation reagents and b) the degree of conditioning before flotation. Coal recovery at a rate of 0.504 kg/s (2 tons/hr) was demonstrated at a pond site employing a mobile froth flotation unit.

Jan 1, 1988

Mining at Hudson Bay Mining & Smelting's (H. B. M. & S.) Snow Lake Division is now in the mature stage of the mines lives. These base metal copper-zinc mines have been operating for over 30 years. Stopes had small pillars called "crown pillars", left between them. These pillars range up to 100 meters long by 40 meters wide and 15 meters thick. H. B. M. & S. has been successful in removing these pillars through the use of cable slings, electric scoops, longhole mining and diesel LHD equipment. The different shapes and sizes of these pillars has meant that many innovative techniques have been tried in order to find acceptable economic mining methods. An overview of the different methods will be outlined.

Jan 1, 1992

By E. F. Divers

In response to a request from the Mine Safety and Health Administration, the Bureau of Mines has recently completed a respirable dust survey of 18 U.S. coal preparation plants. Of these, three were essentially free of dust problems. Respirable dust exposure of workers in the remaining plants depended on the time spent in the dusty areas. In five of the plants surveyed, Bureau tests showed that in some areas worker exposures could exceed Federal dust limits in less than 2 hours.

Jan 1, 1988

By Russell G. Hood

Rock bolting or anchoring are methods of stabilization which are not being fully utilized in California and probably in other parts of the world due to lack of understanding of the principles, or due to poor results in actual installation. The problem is greater in California because so much of the rock is either soft or badly fractured and broken. Almost any recognized type of rock bolt or anchor will perform successfully is hard, fresh rock, but the problems become many-fold when working in decomposed granites, shales, soft sandstones or other soft, highly-broken rock. There has been an enormous amount of research by manufacturers, consultants, private organizations, and governmental agencies on rock bolting. It would be impossible to discuss all the methods and philosophies of rock bolting in this paper. Therefore, with the indulgence of the experts, I will give only a very generalized coverage on rock bolting techniques. However, My main purpose is to point out some of the problems of rock bolting in soft rock.

Jan 1, 1967

By J. Perlacia

Introduction The Bulk Handling Technology has already started its transformation to the Industry 4.0. Having some of the harshest working and environmental conditions of the industry, the possibility of remote analysis and maintenance of the components seems a perfect target to focus on. The most important and expensive tools have been adapted to the digital era during last years, from remotely controlled haul trucks to monitored conveyor belts. However, these big parts of the installations rely in smaller parts that have been left aside for a while, mainly due to the difficulty to adapt them to IoT (Internet of Things). The paradigmatic example is the lack of monitored rollers whereas all the other components of the conveyor belt installations (the belt itself, motors, drums etc.) were monitored some time ago. The main problem is that a failure of a single roller can cause the stop of the whole conveyor, due to the possible damages to the belt, thus the implementation of an integral monitoring system of all the components of the conveyor is a must. The R&D Department of ULMA Conveyor Components, has been working since early 2012 on the development of Monitored Rollers, facing all the problems until its final installation in very different demanding conveyors, from the Australian extreme heat to the freezing cold Norway. All the tests done under actual working conditions, in real installations, have given a valuable knowledge in the identification of problems, their solution and the final advantages of a roller monitoring system. Background and Current State The malfunction of a single roller in certain conveyor belts can suppose the standstill of the whole installation until its replacement, due to the risk of greater and more expensive failures like the rip of the belt. In the case of a bulk handling installation where a continuous supply of material is necessary, an unexpected stop of one hour could entail huge economical losses. What’s more, many conveyor belts are several kilometers long or the access to some parts of them is very complicated. Due to these difficulties the inspection and maintenance operations can become expensive and hard going, with staff going over the whole area checking the correct condition of the conveyor and rollers, which means a dangerous activity. As in many other industry products, the condition of rollers can be recognized measuring key parameters like the temperature of the bearings, the vibration level etc. The traditional way is to use the characteristic noise of a failing bearing, but this method usually implies to change several rollers because the maintenance team is not able to identify a single source of the noise. In recent years different attempts to measure the temperature of the bearings have been made, but the result is not accurate enough due to the proximity of the rollers in the idlers

Jan 1, 2019

By L. D. Savage

Several experiments were conducted using a large crib fire adjacent to a Kennedy Metal Products steel stopping in a simulated cross cut to evaluate the proposed mechanisms by which a mine fire would breach the stopping. Temperatures in the convective air paths on both sides of the stopping, at the surface of the roof and 16mm within the roof were measured to evaluate the effects of heat transfer. The results indicate that roof failure is the prime method of breaching this design of stopping.

Jan 1, 1996

By Peter J. Szabo

The mining executive works in a cyclical industry. His employment is subject to the vagaries of the marketplace. Boom and bust has always been the industry's story. "Big oil" failed in its mining effort. This left emotional and financial scars on many mining families. One must remember that mining executives always play a high-stakes game. Given the cyclical nature of the mining industry, mining executives need to take care of their own financial security. The mining executive that does not plan for his financial security in this cyclical business is playing Russian Roulette with his future. Take a look at those people who have reached their later years with the mining industry. One usually finds three categories of people. Those few in the first group have been fortunate enough to have worked for one company. They have survived the winnowing process of cyclicality, political problems, and takeovers. They have reached normal retirement age. For them, the retirement years are usually comfortable. People in the second group have worked for those same mining companies. But these people have been forced out by early retirement. Or they have been laid off for cyclical, takeover, or political reasons. The third group includes those who have held many positions in the mining industry. Probably not until their later years are they fully vested, if at all, in a pension program. The first small group, then, is the exception. The others, unless they have taken care of their financial security, are doomed to later years of financial problems, stress, and unhappiness. Too late in life, many realize the harsh realities of failure to plan and implement a personal financial program. Mining executives go to some of the world's leading mining schools, to learn how to make money. The curriculum is technically strong. Most mining graduates are familiar with the intricacies of discounted cash flow, present value, and the Hoskold formula. But few of these same mining schools require courses on personal financial planning. Such courses could give mining students a realistic foundation and the mechanisms with which to cope with their cyclical profession. An executive has only three sources of money. He can make money at work. He can put his money to work. Or he can get money from charities, such as government programs. Of these three sources of money, money at work has the best chance of providing financial security in later years. The mining executive must think of the day when he will be too old to work and contribute to the market place. At this point, the quantity and quality of his investments will determine whether his later years will be secure. Along with the Mining Engineering Handbook, two key books should be included in the mining executive's library. These are Venita Van Caspel's The Power of Money Dynamics and Benjamin J. Stein's Financial Passages. These books contain the basic concepts of personal financial planning so critical to an individual's financial survival. Venita points out the simple formula that is the key to financial independence: Time + Money + American Free Enterprise (Rate of Return) = Opportunity to Become Financially Independent Chart 1 shows that this is not a trite formula. The chart shows the dramatic effects of compounding over time. The chart also shows at various yields what a $2000 a year Individual Retirement Account (IRA) contribution will accumulate. Chart 1 (from Money magazine) is based on the future value of an ordinary annuity. It shows that the key to amassing a small fortune by the time a person reaches his 50s is starting to save methodically in his 20s. This, coupled with the highest yields consistent with safety of principal will ensure financial security. There are significant effects from compounding money over time. Every year the decision is put off to save for later years will cost a person dearly by the time he reaches his 50s. For example, consider the decision to put off for one year a $2000 IRA investment at a 12% return. Starting it at age 31 instead of 30 will cost the executive almost $100,000 by age 65. What if the executive waits until age 35 to get started with his $2000 a year investment? He will then lose nearly $400,000 by age 65. Stated another way, the executive costs himself this $400,000 simply because he did not invest $167 a month for five years. $167 a month - that's less than an inexpensive second car payment. This $400,000 pool of money could provide the executive a $40,000 a year income at age 65, assuming a 10% return on invest-

Jan 11, 1985

By Ralph J. Anctil, James E. Palmer

According to relatively recent estimates by the US Geological Survey and the US Bureau of Mines, there are more than 0.9 Tt (one trillion tons) of remaining identified coal resources in the seven major western US coal-producing states and about 200 Gt (220 billion tons) in the demonstrated reserve base. Considering coal's current national production level of 0.7 Gt/a (0.8 billion tpy), these US reserve and resource figures are reassuring. Given here is a preliminary analysis of geologic constraints and an estimate of their effects on mining and recoverability of western coal. Mining Constraints USGS and USBM coal figures incorporate only thickness and depth, and are "blind" to many other major geologic constraints on mining and recoverability. The most important of these geologic constraints include: • coal seams too thin or too thick for conventional mining methods; • coal seams that cannot be mined due to insufficient separation from underlying or overlying previously-mined beds; • unstable or otherwise unfavorable roof strata; • soft or heaving floor strata; • coal seams that are too lenticular or discontinuous for conventional mining methods; • coal seams in intensely faulted areas; • coal seams having high angles of dip precluding the use of conventional coal mining methods; • coal seams that cannot be mined due to proximity of water-bearing strata; and • coal quality problems such as excessive ash, sulfur, chlorine, or sodium. Coal Thickness Present USGS-USBM classification for reserve base includes bituminous coal beds more than 0.7 m (28 in.) thick and subbituminous beds more than 5 m (60 in.) thick to depths of 305 m (1,000 ft). Both of these thicknesses are less than the thicknesses now considered mineable in the western US. The lower limit for bituminous steam coal in deep mines is about 1.5 m (5 ft). For subbituminous coal, a thickness of at least 2.4 m (8 ft) is generally required. Accordingly, the Bureau of Mines reserve base includes many thinner coal seams that will not be mined in the foreseeable future. Within the Powder River Basin of Wyoming and Montana many seams-Wall, Upper Pawnee, Lower Pawnee, Cache, Manning-range in thickness from 7.6 m (25 ft) to more than 30 m (100 ft) and occur at depths to 305 m (1,000 ft). These have been included in the Bureau of Mines reserve base. However, the mining technology required to mine these thick seams does not now exist. It will require many years for development. The ultimate recoverability from these thick seams is unknown, but could be as low as 25%.

Jan 8, 1982

By G. Jalkanen

Dealing with a trend in inverse distance estimation, IWD, is presented. A measurement is proposed to be consisted of a portion due to a mean and a portion due to a residual. The procedure consists of de-trending the measurement via a linear or nonlinear regression. Residuals are computed, and IWD parameter estimation is conducted on the residuals. Estimation at un-sampled points is then computed by estimating the mean and adding on the estimate of the IWD on the residual. A possible BOXCOX transform is also proposed.

Jan 1, 2010

By E. H. Partelpoeg, B. G. Belew

In 1990, the Chino Smelter completed the construction of a plant designed to recover metal values and water from smelter scrubber effluent. Equipment was installed to maximize effluent recycling and minimize costs. The process utilizes magnesium hydroxide as a neutralizing agent which has the advantage of precipitating copper from solution with minimum generation of solid reaction products. The neutralized stream is clarified, with solids recycled to the smelter for metal recovery while the clarified effluent is recycled to the concentrator for use as process water.

Jan 1, 1992

By K. Chandrasekaran

Carbon-in-leach (CIL) is conventionally used in gold processing operations when preg robbing components are present in the ore. The CIL process is becoming attractive even in other situations when preg robbing is not a factor. This article discusses the situations in which the CIL circuit can be applied. The results of leach-carbon-in-pulp (CIP) and CIL circuits at Newmont Gold's Mill No. 2, No. 4 and No. 5 are presented for comparison: Mill No. 4 was initially designed for a throughput of 4.1 kt/d (4500 stpd). It is presently operating at an average throughput of 6.6 kt/d (7300 stpd) without significant changes to the original design. The design considerations of the Mill No. 4 CIL circuit are discussed. The design of any processing facility represents a series of decisions. The final design options should ultimately be resolved based on economic as well as technical considerations. Every design decision represents some sort of compromise. From the designer's view point, these decisions are made with the conviction that the final product represents the most prudent long-term expenditure. The design throughput rate is a decision reflecting a maximum return for the capital and operating costs that the plant will incur over the life of the mineral resource. The result is a plant that is not operator proof or maintenance free because it would be too costly to build. At some point, the incremental increase in the level of capital expenditure would not adequately compensate for the lower

Jan 1, 1991