Search Documents

By Richard A. Hunnisett

Silica sand is one of the world's most plentiful resources and is a basic necessity in our way of life. The end uses of silica sand are an integral part of our homes, transportation, and places of work. The environmental legislation enacted in the early 1970's, coupled with the oil embargo and higher than normal inflation, have had a very real impact on the industry and its primary consumers, the foundries and glass producers. The present environmental laws directed at air and water pollution and the working environment can, in most cases, be met, but not without large capital expenditures for equipment. These expenditures must reduce the funds available for expansion and modernization of existing processes which are necessary if the costs to produce industrial sand are to remain at acceptable levels. The concern for the future is the enactment of more stringent laws, and the available technology and equipment to economically comply with them.

Jan 1, 1978

By S. K. Kawatra, T. C. Eisele

To reduce their sulfur emissions, many coal-fired electric power plants use wet flue-gas scrubbers. These scrubbers convert sulfur oxides into solid sulfate and sulfite sludge, which must then be disposed of. Currently, the major markets for scrubber sludge are for manufacture of gypsum products, such as wallboard and plaster, and for cement. However, the quality of the raw sludge is often not high enough or consistent enough to satisfy manufacturers, and so the material is difficult to sell. Other markets, such as paper manufacture and plastics fillers, have even more stringent quality requirements and will not accept raw sludge at all. In the work described in this paper, several reagents have been examined to determine their ability to selectively improve the flotation of the unreacted limestone contaminant away from the desirable products (calcium sulfite and gypsum). The most success has been achieved using a cationic collector, which shows a higher selectivity between calcium sulfite and calcium carbonate than do the anionic collectors that were studied.

Jan 1, 1995

By Ted D. Johnson

INTRODUCTION The report of the workshop on Alternate Energy Strategies estimated that the world's reserve of uranium oxide is about 700,000 tonnes. In order to extract these reserves, it is estimated that between 100 and 200 million tonnes of solid waste and of the order of 1 billion cubic meters of liquid waste will be generated. In addition, radium within tailing will continue to generate radon gas as it decays for many years after closure. Hence, the handling, storage and possible use of uranium mine waste is a matter which deserves serious consideration and planning. Since the properties of the waste will largely dictate the method of handling and storage or use of the waste, the properties of the waste should be determined, to the degree possible, prior to the design and subsequent operation of the mine. Uranium mine waste has both solid and fluid constituents. The solids include soil and rock removed during site preparation, similar material removed during development of the mine and uranium tailing generated by the mill. Soils can be stockpiled for reuse during reclamation or used as earth materials for construction of fills, roads, dams and soil linings. Rock can be stockpiled, used as mine backfill or can be used for earth construction in fills, roads and dams. The tailing is usually placed in a tailing storage area. The fluid constituents are both liquid and gaseous. The liquid waste is generally composed of the mill water; however, additional waste water can be generated by dewatering processes and diversion of surface runoff. The gaseous constituent of the uranium mine waste is radon generated by the radioactive decay of radium in the ore tailing. DEFINITION OF PROPERTIES The following presents a brief definition of some of the more important properties discussed later. The definitions are not intended to be comprehensive, but are useful as a basis for understanding.

Jan 1, 1980

By Richard P. Killmeyer

In 1985 the Pittsburgh Energy Technology Center (PETC) of the U.S. Department of Energy (DOE) conducted a study to evaluate the emerging selective agglomeration processes (Killmeyer, 1985). This paper covers a recent similar study evaluating an associated technology, the emerging advanced froth flotation processes. This study has goals similar to those of the 1985 study: to evaluate the emerging froth flotation technologies collectively and determine how far they have progressed in their ability to clean ultrafine coal, and to assess the differences among the participants. The major concern again in this study was not the level of development, nor the economics of each individual process but only the current technical performance.

Jan 1, 1989

By G. A. Gordon

For the purpose of examining a specific problem, it is important that we look at the context, to obtain an appreciation of the general area of which the particular problem forms a part. It is my task today to speak on a particular relationship between the nations of Canada and the United States of America. What is the background? Almost two hundred years ago we both belonged to a family of nations -- the British Empire. There was a serious family quarrel in 1776 and the United States left the family and set out to make its own independent way in the world. Canada, which was not as grown up as the united States, remained with the mother country, and in 1812 resisted a vigorous attempt by the United States to get it to leave home too. With the passing of the years the bitterness of that family quarrel has faded and, aside from occasional differences, we have been getting along very well ever since.

Jan 1, 1962

By Richard R. Klimpel

Part 2 of this article continues the discussion of a 10-year, multimillion dollar research and plant testing program on slurry rheology and grinding circuits. The first part of the article (ME, Dec. 1982) presented the basic concepts identified by the research and some laboratory test results. This section Illustrates typical Industrial scale test results and Identifies some industrial operating implications of controlling rheology by different methods. At least four controllable factors decide the rheological character of a slurry-slurry density or percent solids, particle size distribution, chemical environment, and slurry temperature. The second factor has two interrelated facets: the shape of the particle size distribution which controls packing behavior of the solids, and the fineness of the distribution. Finer particles increase interparticle forces and viscosity. As indicated in Part 1, during a given grinding test it is possible for all four factors to change. However, regardless of the particular settings of the four factors in a given test, if the resulting rheological character is either dilatant, pseudoplastic, or pseudoplastic with yield, the associated breakage rate is correlated with the current rheological character. It is obvious, for example, in batch grinding tests run at constant percent solids, that the second and third factors, where appropriate, are changing during grinding because size distributions are changing and the production of fresh surface area takes up unadsorbed chemical. Thus the corresponding rheological character change in batch tests with increasing grind time would be dilatant to pseudoplastic to pseudoplastic with yield. The degree to which this transformation occurs depends on the changing setting of the four factors over grinding time. In continuous grinding tests, one might logically expect that dramatic changes in any one of the four factors will be less likely to occur. It will be shown that continuous mill operations offer some unique opportunities to take advantage of possible rheological transformation by more direct operational control of the settings for the four factors. One extra observation noted in the rheological studies was the variability in the location and extent of region B (pseudoplastic behavior) for the various coals and ores tested. The location of region B was usually in the region of 45-55% solids by volume and was of the extent of 0-8%, or 2-11% with chemical addition. The corresponding increase in net production ranged from 0-10% in region B and 0-21% in region B&apos;. When region B is small or zero (no pseudoplastic character is exhibited) no increase in production will be observed and the use of chemicals is often marginal. There are several reasons for some materials exhibiting this quick transformation from dilatancy to high yield values often at surprisingly low percent solids by volume such as 30%. One condition identified was for materials containing high levels of viscosity-producing elements such as- carbonates or clays. A second condition documented was for materials that exhibited unusually fine primary fragment distributions (fine B1,; curves). This corresponds to materials having small y values of < 0.5. Such a slurry developed a yield value quickly during grinding because of the rapid buildup of fines. A related problem can be presented by materials exhibiting excessively coarse primary fragment distributions, y values > 0.9. Breakage of this type of material produces size distributions that give poor packing efficiencies even at long grind times, thus hindering the normal rheological transformation presented earlier. A final condition that can cause the occurrance of region B to be small or zero is when the media void volume filling of slurry is < 100%. Figures 5a and 5b use previously published data of this study to demonstrate the influence of solids loading and weight percent solids on the net production of taconite ore in a laboratory batch ball mill. In particular, Fig. 5a illustrates several trends not generally recognized until this study. They include these two: • Increased slurry density allows for increased solids loading before passing through the maximum in the net production curve where the fall-off is due to non first order breakage. • The use of rheology control chemicals such as GA-4272 allows this trend to be extended to higher slurry loadings with an increase in net production over any previous condition by keeping grinding first order. Figure 5b shows the same data as Fig. 5a plotted for constant weight loadings. These various figures of net production versus percent solids show the location and extent of the regions A, B, and C presented in Part 1 as a function of solids loading. It is obvious that the rheological transformation pattern described earlier does not hold true for slurry loadings corresponding to less than the void volume of the media, which is also a region of

Jan 1, 1983

By A. W. Mitchell

Mining of a bedded barite deposit exposed highly pyritic siliceous sediments which have weathered and degraded subsurface and surface waters. The ph, sulfate, and total dissolved solids are the most seriously affected parameters. Several solutions were tried and eventually horizontal holes were drilled into the mine wall to draw down the water table and decrease the movement of groundwater through oxidizing zones opened up by the mining operation. Areas of surface disturbance were capped with layers of soil, bentonite, and gravel to decrease the infiltration of water into the disturbed areas. These actions have begun to decrease sulfate and total dissolved solids concentrations and increase ph values.

Jan 1, 1987

By R. E. Miller

Accelerometers and pressure transducers mounted in suspension components can be used to monitor the ride of haulage trucks. Presently, it is difficult to tell what caused a jolt to the truck using either pressure or acceleration data alone. When information from a Global Positioning System is recorded at the same time as shock pressures or acceleration data, then the exact location of an event can be determined. Mine management can then determine what caused the jolt to the truck.

Jan 1, 1999

By Patricio Zarate

Due to the intrinsic variability in orebodies, similar metallurgical behaviour of all material sent to the concentrator is expected to have some variability. Still some specific ores have anomalous performance which can severely impact on the concentrator’s production of metal, in this case copper. The study first will show the mineralogical characteristics of “usual ore” and of this specific “abnormal ore” which will have to be processed by the concentrator in the future. After that base conditions on both ores and flotation test procedure will be explained. Later the different alternatives tested regarding collectors and modifiers results will be compared. Finally, after discussing the different results with different reagents and considering operational variables of the concentrator, Floticor PD 702 is recommended to obtain the best copper recovery without increase in excess mass recovery.

Feb 1, 2025

By L. Neuman

Reclamation and permit applications for mines tend to be very detailed and complicated documents. Depending on its complexity, the application may have to be reviewed in detail for water quality, water quantity, wetland and upland habitat, wildlife issues, waste disposal, historical and archeological significance, other environmental factors, and financial surety sufficiency. To reduce review time and cut costs to the applicant, this paper identifies the most common mistakes that can lead to delays in the application process.

Jan 1, 2004

By Lynn B. Hales, Randy Ynchausti

Expert systems are now being used effectively to streamline and improve the performance of supervisory computer control strategies. Their advantages have led to use in both batch and continuous applications. Expert systems in the context of real-time process control, will be defined and examples of their successful implementation in autogenous, semi-autogenous and ball mill grinding circuits will be discussed.

Jan 1, 1990

By D. Erik Spiller

Introduction The recovery of precious metals from ore can generally be accomplished using either gravity concentration, flotation, and/or hydrometallurgical (leaching) techniques. The objective of this paper is to show why gravity concentration can be an important part of recovery systems which employ leaching as the primary unit operation. A brief discussion of modern gravity concentration equipment is also presented.

Jan 1, 1984

By Thomas J. Lien

AMAX Coal Company has constructed the first commercial demonstration sub-bituminous coal dryer at its Belle Ayr Mine south of Gillette, Wyoming. This 215 ton per hour facility is projected to produce 165 tons per hour of dried coal at 10 percent moisture and 10,800 Btulpound (6,000 KCIkg). Approximately 43 tons per hour of water will be removed from the coal and seven tons per hour of coal burned as fuel.

Jan 1, 1989

By Mahmud Esad Uluer, Aaron Noble

Respirable coal mine dust (RCMD) is one of the biggest occupational health hazards for underground coal miners. Coal extraction is a main source of RCMD. To prevent challenges related to RCMD from developing, it is vitally important to limit airborne RCMD and stay within the regulatory limitations for mine operators. The flooded-bed dust scrubber (FBS), mounted on a continuous miner, is one of the most widely used dust mitigation technologies in room-and-pillar mining, but it is limited by technical challenges, the most notably being the potential to clog. In this study, the impact of mesh design and surface modification on system efficiency is examined using different vibrating, liquid-coated, stainlesssteel mesh panels in a laboratory-scale FBS.

Sep 1, 2024

By Lynn B. Hales, Randy A. Ynchausti, Robert W. Colby

Process control systems have evolved from single loop control to distributed control with computer based expert control strategies. The next step is to add adaptive control to the expert control strategies. An object-oriented intelligent adaptive optimization approach is defined and simulated results are presented.

Jan 1, 1995

By D. W. Alexander

Mine fires, explosions, spontaneous heating and inundations are among the leading causes of catastrophes (unplanned, temporary sealing and recovery of major mines). Many reports are available that detail company efforts to re-establish mining operations and agency efforts to regulate away the causes, but the associated costs are rarely included. The increasing scale of coal operations concentrates earning potential and the financial risk of business interruption in fewer locations. Underground coal mine catastrophes are low probability, high loss events that happen nearly every year. This paper will present an evaluation of coal mine catastrophes from case studies.

Jan 1, 2003

By L. Mao, R. Yoon

The thin film balance (TFB) technique was used to measure the equilibrium thicknesses of the water films formed between two oil phases. The measurements were conducted with dodecane at varying concentrations of dodecylammonium chloride, pH, and electrolyte concentration. The data obtained in the present work were used to calculate the surface forces acting between the two oil phases. The calculation was carried using the Extended-DLVO theory with the surface potentials calculated from the Gibbs adsorption isotherm. The results show that oil droplets suspended in water are hydrophobic and the hydrophobicity changes with surfactant and electrolyte concentrations.

Jan 1, 2004

By F. Wendling, G. M. Peixoto, J. A. M. Cano

A brief introduction is made on the existence of sulfides in the top gas of the Midrex Shaft Furnace, giving consideration to the operation of the furnace and the liberation of sulfur, as well as its consequential effects on the reduction process. The text shows a study of sulfur distribution in the pellet, emphasizing the importance of this distribution in relation to the liberation of sulfur during the reduction. A study was made to determine the sulfur compounds that exist in the pellets, showing ways of controlling the sulfur distribution and reducing its liberation during reduction.

Jan 1, 1991

By Thomas S. Kovach

In today&apos;s competitive energy market, every effort must be made to assure the lowest possible production cost. &apos;rhi s. paper describes the cooperative effort between the coal producer and the utility customer to develop and install a fully integrated mine information management system at a 2.5 million tpy lignite mine in east Texas. A description of each item of the modules is included along with the problems encountered during development and how they were corrected. The system configuration is also described.

Jan 1, 1989

By D. L. Passmore, J. D. Bennett

The reliability of mine operators&apos; reports to the Health and Safety Analysis Center of the US Department of Labor of days lost from work by injured miners is 0.267.

Jan 1, 1987