Search Documents

By R. K. Mehta, C. W. Schultz, R. R. Mallepali

Stirred ball mill feeds used for ultrafine grinding applications require a fine size separation step to avoid overgrinding. This paper presents the selectivity curves obtained for oil shale and complex sulfide ore using a 460-mesh (30-µm) Derrick vibrating screen. The selectivity curves generated from the experimental data show increasing selectivity with larger size for the oil shale but not for the sulfide ore. These unusual selectivity curves are similar to the mechanical air separator, fishhook selectivity curves described by Luckie and Austin. A two-stage, in series, classification model describing the fishhook selectivity curve has been used in proposing the classification mechanism for fine vibrating screens when a heterogeneous, multicomponent sulfide ore undergoes size separation.

Jan 1, 1994

By A. Ghalambor

The objective of this investigation was to determine the sensitivity of three selected input parameters in the operational control of continuous bottom-fed thickeners used for the treatment of coal refuse slurries. The three variable parameters were "Feed Flow Rate," "Feed pH," and "Feed Solids Concentration." These three input parameters were studied under three polymeric conditions which were cationic polymer, anionic polymer, and a combination of cationic-anionic polymer. For each polymeric condition, two mathematical models were developed: one for overflow response, the other for underflow response. The combination polymers produced the best desired quality of overflow and underflow. For this polymeric condition, changes in the feed solids concentration was the most sensitive factor in the maintenance of the overflow quality, and the feed pH was the most sensitive factor for the maintenance of the underflow quality. The mathematical models generated a set of plots which would allow an operator to control and/or adjust any of the three variables to achieve optimum conditions.

Jan 1, 1989

By C. H. Bucknam

A suite of ore and waste rock materials was selected for the interlaboratory testing of combustion-infrared ("Leco") methods used to estimate carbonate and sulfide minerals present in test materials. The objective of the study is to develop ASTM standard methods to be used for metallurgical characterization of ore, acid drainage prediction for ore and waste during ore body evaluation, and for ore and waste control during the active mining of ore deposits. The results may be interpreted for classification of the materials according to their carbonate-sulfide or acid-base characteristics based on net carbonate value (NCV). The test materials were processed by x-ray diffraction and x-ray fluorescence (XRD-XRF) at Newmont Metallurgical Services (NMS) to obtain a semiquantitative mineralogical composition. Results of the interlaboratory testing for total carbon-sulfur, pyrolysis loss carbon-sulfur and hydrochloric acid residual carbon¬sulfur are compared with the mineralogical composition to aid in interpretation of the NCV classifications of the samples.

Jan 1, 2002

By J. D. Patsey, G. T. Lineberry

A.E. Hall The authors are to be commended for their attempt to provide a convenient piece of software for preliminary drum hoist specification. This field has received little attention in recent years and is eminently suited to calculation by computer. Unfortunately, there appears to be an error in the calculation of the required rope diameter. The 66-mm (2 5/8-in.) rope selected is oversized for this application. Wire rope weight and breaking strength are related to the rope diameter. For a round strand rope

Jan 8, 1987

By D. J. Murdock, Wyslouzil, I. M. Flint

The highly competitive nature of the international iron ore market has forced producers to improve the quality of their pellets. The demand for low-acid pellets suitable for direct reduction has resulted in an increase in the number of plants utilizing reverse froth flotation for silica reduction. Column flotation is being favored for this service because of low capital and operating costs and improved metallurgical performance compared to conventional flotation cells. This paper describes the benefits of column flotation and discusses some important aspects of circuit design.

Jan 1, 1995

By A. C. Smith

Although it is only utilized in a few U.S. longwall mines, a bleederless ventilation system can be an effective spontaneous combustion control method in mines with a demonstrated history of spontaneous combustion. In order to provide insights for the optimization of bleederless ventilation systems for U. S. underground coal mines, a computational fluid dynamics (CFD) study was conducted to model the spontaneous heating in longwall gob areas with a bleederless ventilation system. A single longwall panel with a bleederless ventilation system was simulated, and typical ventilation data for a longwall mine was used in the simulations. The permeability and porosity profiles for the longwall gob were estimated using a geotechnical model and were used as inputs for the CFD modeling. The effects of gob permeability and resistance of the collapsed entries on the spontaneous heating were studied. The effectiveness of nitrogen injection to prevent spontaneous heating in the gob was also examined. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health.

Jan 1, 2008

By E. E. Bauer

Oversize boulders in mines and quarries must be broken for waste disposal or further processing of ore. Early methods involved drilling and "shooting" or using a drop ball of sufficient weight to accomplish the purpose. The first "high-energy" hammers for breaking concrete or boulders were pneumatically operated. Blow energy was limited by valving and air pressure. However, smaller boulders of lower compressive strength could be broken. A hydraulic excavator-backhoe type machine was required for either a drop ball or hammer. Standard practice was to break oversize boulders in the pit before hauling to the grizzly or crusher. Generally, quarry boulders were not valuable enough for further processing. Quarry roads were lined with oversize boulders. As safety requirements were advanced, "drill and blast" for boulders was ruled out.

Jan 1, 1994

By R. D. Hamilton, W. J. Miles

In 1987, the International Agency for Research on Cancer designated crystalline silica as a 2A probable carcinogen. As a result, crystalline silica is regulated under the Hazard Communication Standard as a probable carcinogen at a concentration of 0.1% or greater in the workplace. Crystalline silica will be listed as "reasonably anticipated to be a carcinogen" by the National Toxicological Program. This designation of crystalline silica as a probable carcinogen has created major issues for the mineral and chemical producer, including labeling, hazard communications, marketing a material with potential hazard exposure, and potential liability. The State of California also regulates crystalline silica under Proposition 65 in products as a carcinogen, based upon the IARC determination that it is a probable carcinogen. More federal and state regulations are anticipated as a result of the IARC classification of crystalline silica and its subsequent federal regulation. Respirable crystalline silica has been regulated as a hazardous dust for many years by OSHA. This regulation was initiated to prevent silicosis, another occupational disease. OSHA has established monitoring devices for determining the concentration of airborne respirable silica in order to measure exposure to this substance. The accurate determination of the crystalline silica content is critical to dealing with these health risks and regulations. In the past, crystalline silica was considered to be safe and, because of its ubiquitous nature, little effort was made to determine or quantify its presence in most materials. The Hazard Communication Standard requires that a1l products containing 0.1% or greater crystalline silica must be properly labeled for this material and its hazard. Unfortunately, the 0.1% threshold was not chosen on the basis of established analytical capabilities for crystalline silica, but results from general limits for potentially carcinogenic chemicals and substances. Numerous methods have been developed for the determination of crystalline silica in a variety of products. However, these methods are not generally applicable since they must be specific for silica in any of its crystalline states and not just for total silica content. Chemical tests for silica are not difficult and quite accurate at the 0.1% level; however, in addition to its crystalline phases, it occurs in amorphous phases and in a wide variety of crystalline and amorphous silicates. In general, there is little correlation between total silica content and crystalline silica.

Jan 1, 1991

By A. E. Hall

The authors are to be commended for their attempt to provide a convenient piece of software for preliminary drum hoist specification. This field has received little attention in recent years and is eminently suited to calculation by computer. Unfortunately, there appears to be an error in the calculation of the required rope diameter. The 66-mm (2 5/8-in.) rope selected is oversized for this application. Wire rope weight and breaking strength are related to the rope diameter. For a round strand rope

Jan 1, 1988

By John R. Turney

MARY KORPI: Harry Hinds will be filling in for John Turney today. Harry is an exception to the industry these days, in more ways than one. He has worked for the same mining company for 33 years. That is something very few of us can claim. He is currently metallurgical superintendent for Homestake Mining Company in Lead, South Dakota. Harry is also the envy of many of us as he will be retiring this year and working on lowering that handicap! Harry will be discussing the "Role of Consultants."

Jan 1, 1998

By A. John R. Hart

INTRODUCTION The use of precast concrete tunnel liners as the initial and final tunnel lining for transit systems has been a major consideration of designers for over three decades. The obvious benefit of building a tunnel that requires only a single pass in constructing the structural lining can provide the opportunity of saving both time and cost. This technique has had worldwide application in transit systems in London, Munich, Hong Kong, Toronto to name a few. In the United States precast liners were evaluated for use on the BART System in San Francisco in the early 1960's but did not provide sufficient confidence in the sealing capabilities available at that time. In 1976 it was decided to call for bids on the Lexington Market Tunnels in Baltimore with a precast concrete liner alternative for one of the tunnel drives. This option was selected by the owner and UMTA to provide a study evaluation for the benefit of the industry. HISTORY In 1983 Washington Metropolitan Area Transit Authority began calling for a series of bids on soft ground tunnels on the Green Line, which included the option of using precast concrete tunnel liners first as an alternative to fabricated steel tunnel liners. Over the years following, the precast concrete tunnel liners have become known as the conventional tunnelling system and, in the last year,

Jan 1, 1989

By Firoze E. Katrak, John R. H. Black, Paul R. Ammann, Michael J. Loreth, Servi. Italo S.

Germanium is produced primarily as a by product from zinc concentrates. The important sources of gallium are alumina ores (bauxites) and zinc concentrates and residues from zinc processing. In addition, gallium as well as germanium may soon be recovered from a depleted copper mine near St. George, Utah. The major uses for germanium are in semiconductors, lenses in infrared optical systems, catalysts, and gamma radiation detectors. The major markets for gallium are in light-emitting diodes, solar cells, laser diodes, integrated circuits, microwave devices, and magnetic bubble memories. CRA projects a healthy growth in the demand for both metals. However, the role of scrap metal will continue to be important over the next decade, thus decreasing the overall demand for primary gallium and primary germanium. This paper summarizes the key elements and the economics of the markets for germanium and gallium. Much of the information, such as plant-by-plant costs of production and estimates of consumption by end use for various countries is from proprietary databases of Charles River Associates.

Jan 1, 1986

By Terry I. Mudder, Michael M. Botz

Discharge regulations for mine waters require relatively low concentrations for cyanide and metals, and the trend is for discharge limits to be lowered. In the event conventional treatment practices are not sufficient to meet discharge limitations, advanced treatment technologies such as ion exchange and reverse osmosis may be considered. Though these technologies will provide discharge quality waters, they also require the disposal of a concentrated brine and are relatively complex and costly to operate. Many mine sites currently using activated carbon in precious metals recovery present the opportunity to economically operate an activated carbon water treatment plant for polishing of effluents. This paper presents summaries of six ( 6) mining operations which have evaluated or use activated carbon for treatment of water and which also use carbon in precious metals recovery processes.

Jan 1, 1997

By Paul D. Chamberlin

In the author's selenium report of 1994 (1), the literature was culled for selenium removal technologies that had a chance of producing effluents with <10 ppb of total selenium. Very few processes could achieve such low concentrations. The EPA dictates such low concentrations. Discharges to fishery waters must be <5 ppb total selenium. The federal max­imum contaminant level ( MCL) for drinking water is 50 ppb. The EPA regulations are for total selenium, not for the species, perhaps because an approved EPA assay method is atomic absorption and it cannot distinguish between species.

Jan 1, 1996

By Lee W. Abramson, James E. Crawley

Caltrans is studying alignments for a 160-kilometer-long high speed ground transportation system from Los Angeles to Bakersfield across the Tehachapi Mountains. This link is needed to connect southern California with San Francisco by a short passenger rail service. None presently exists. The system will require tunnels and viaducts along the route with sections crossing two major active fault zones. High speed ground transportation technologies are being evaluated for achieving rail speeds of between 200 and 480 kilometers per hour. This paper presents the technical requirements for tunnels along the alternative routes being considered for the project.

Jan 1, 1995

By S. Vijayan

Despite the limited demand for rare-earth elements, as well as yttrium and scandium, in conventional applications, the emergence of ne~ high-technology applications such as supermagnets, lasers and superconductors is expected to result in significant demand for some of these elements. This paper examines the anticipated applications and demands for rare-earth elements over the next decade and their implications on the utilization of available resources. Process methods for the recovery of rare-earth elements from conventional and unconventional resources are reviewed in the context of their growing demand. Challenges facing the industries in meeting this opportunity are also discussed.

Jan 1, 1988

By Peter D. Warwick

Recent investigations conducted by Federal, State, and industry organizations suggest that significant coalbed gas resources may exist in the Cretaceous and Paleocene-Eocene coal beds of the Gulf of Mexico Coastal Plain. Exploration efforts have focused on three areas which are in south Texas, north-central Louisiana, and south-central Mississippi (Figure 1). Coal-bed gas production is currently underway in south Texas and in north-central Louisiana. In Mississippi, several test wells have been drilled but no data are available on their production potential.

Jan 1, 2005

By James G. Tilton

Subsidence resulting from mining operations, has been the object of sporadic study for many years. Reports have shown that subsidence has ranged from minor settlement detected only by precise measurements to great slips where buildings are destroyed, roads disrupted, and large fissures opened at the surface. For years, a controversy has raged over the question of whether there is a positive or negative angle-of-draw. None of these questions can be given a flat answer for the variables controlling, subsidence are infinite. Generalizations can be made for various situations and areas but some means of control must be executed.

Jan 1, 1966

By Tony Treasure, Ian Ewart

The EMEW® cell has been developed to overcome a number of inherent limitations in conventional electrowinning technology, particularly the high cost and restricted process windows characteristic of conventional hardware. The EMEW technology has been widely demonstrated to achieve high performance for various metals under chemical conditions well outside the limits required for efficient operation of conventional cells. In particular application of the EMEW cell for recovery of silver offers significant operating and capital cost advantages over conventional Merrill Crowe technology used for cyanide based solutions. The cell also offers process advantages for direct silver recovery from nitric acid solutions. The performance of the EMEW® cell on silver cyanide solutions, producing high grade silver metal in a single step, is accomplished by providing a physical mechanism which presents metal ions to the cathode on a highly efficient and continuous basis. The simplicity of design and operation of the EMEW cell offers the following advantages for silver recovery from cyanide or nitrate based solutions: • High grade product in a single step. • Selective for silver over other metals in the electrolyte. • Wide operating concentration range (100,000 - 5ppm). • Ability of the cell to operated in a variety of acid or alkaline electrolytes. (Cyanide, Nitrate). • Simple liquor reticulation. • No pretreatment required - Clarification, deaeration or zinc dust. • High cmTent density and current efficiency compared to conventional electrowinning cell. • Modular design allows for flexible operation and production rate. • Pilot plant results using full scale cell result in accurate scale up design. • Easy/fast installation - cell banks are delivered pre configured with piping and wiring. • Enclosed cell minimizes corrosive vapor and liquid losses in the circuit.

Jan 1, 2000

By V. Fred Swanson, J. Patrick Glynn

The environment for process engineers today is very different from 20 years ago. The ideas and mathematical description of models for a multitude of different unit operations is an ongoing development. The computer tools to deal with the mathematics are readily available and specialist companies have developed, tested and verified their models. The challenge for the process engineer is to know which package to use and to know whether a particular application is the most accurate for the specific process. Metallurgical simulation programs today are well known and proven. Certain programs are specialized while others are broader based. The needs of each user are dependent on the application. Typically, most users require the following operations: • Comminution • Flotation • Hydrometallurgy • Pyrometallurgy • Additional requirements could be defined as: • Thermodynamic capabilities for solids, phases, and gases • Dynamic simulation • Data analysis tools • Coal oriented operations • Diamond oriented operations

Jan 1, 1997