Search Documents

By Victor F. Hollister

This report summarizes data available on the Fort Knox gold deposit to the end of 1989. It is presented courtesy of Fairbanks Gold, operator of the Fort Knox mine. The ore body and the data base are being expanded in 1990, but this summary is pertinent for inclusion in a case history volume that, in part, stresses porphyry-type deposits. Fort Knox is a pluton-hosted gold deposit 22.5 km (14 miles) northeast of Fairbanks, AK. It is easily accessible from Fairbanks, and ultimately it will be the largest open pit gold mine in Alaska. The Fort Knox pluton has an interesting historical record, and it has been discovered at least twice. Fig. 1 shows the geology and location of major plutons in the Fairbanks mining district.

Jan 1, 1991

By D. T. Maiers, P. L. Wichlacz, P. A. Pryfogle, J. H. Wolfram

The effects of metal solution concentration, biomass density, length of exposure time, and pH were determined for biosorption of molybdenum (Mo) and chromium (Cr) by three organisms. Results indicate that it is possible to sorb Mo and Cr from dilute solutions. Differences were observed in the abilities of an organism to sorb Mo and Cr as well as among respective abilities of the three microorganisms. This suggests an inherent selectivity of the organism which may afford the means to control a sorption-based process. Results also indicate that the metal sorption abilities of these microorganisms depend on duration of exposure, biomass density, solution pH, and the metal concentration of the solution. Each of these parameters suggests an additional means of controlling the sorption process.

Jan 1, 1989

By Nancy C. Shaver, Alan Tapp

Leach pads of 272,000 tonnes (300,000 st) and 910,000 tonnes (1,000,000 st) with associated operating ponds have recently been constructed on sidehill locations with up to 20 percent slopes. The larger pad was designed in anticipation of ore heights up to 30 meters (100 feet). This paper describes site investigations and civil engineering design as well as construction experience associated with development of these pads. The leach pads were underlain by a double liner system consisting of 2 mm (80- mil) HDPE over compacted fine-grained tailings, with an intermediate leak detection layer. Both sand and geotextile drainage layers were used. Pad slopes were limited by the factor of safety against sliding on the HDPE liner. The sites for the facilities had been substantially disturbed by prior mining and construction activities. Natural conditions included peat layers and locally swampy ground. Site preparation included french drains to lower the water table and stripping of unsuitable subgrade materials.

Jan 1, 1987

By Zhen-lu Zhao

The manipulators possibly used in underground mining must deal with unpredictable obstacle while keeping certain positions and orientations of end effector, and in some cases, are required to possess redundant joints in order to be more flexible. This kind of manipulators might be fitted with jumbo drill or platform as auxiliary to potentially deal with some utility works in versatile way, such as installing rock bolts, guniting, blasting, charging, surveys and measuring work, etc.. This paper describes numerical procedures of performing inverse kinematic problems for redundant manipulators .The procedures, based on the generalized pseudoinverse of Jacobian matrix, are developed to lead to kinematic solution at both singularity and ill conditioning, and to guarantee continuous sequence of positions of the end effect or. Furthermore, the solution to optimization and obstacle avoidance is investigated. A numerical example is shown to illustrate the approach.

Jan 1, 1989

By Justus B. Deen

Given that the majority of mine ventilation operating costs are imposed by shafts, the need to predict the resistance of a planned shaft with reasonable accuracy is important. During conceptual design, shaft resistances are usually predicted by use of published friction factors, k, based upon lining and fitting configurations. More often than not, published friction factors do not directly coincide with "real" shafts, so their use is somewhat limited. For more accurate shaft resistance determination, equations both theoretical and empirical may be employed if there is detailed knowledge of the shaft. These equations treat the shaft resistance as discrete components, with their sum being the overall shaft resistance. This paper describes the basic shaft resistance equations and verifies these equations by comparison to field measured shaft resistances. Several shafts were examined which varied in depth, shape and fitting arrangements. Results are presented and conclusions drawn to show that the shaft resistance equations are accurate.

Jan 1, 1991

Ever since A Decade of Digital Computing in the Minerals Industry was published in 1969, mining men have expressed the need for an additional reference on computer methods. It was felt such a volume should spell out the "how to" of computer applications in the solution of their problems. Computers in the minerals industry will be 20 years old when the 1979 SME Fall Meeting and the 16th International Symposium on the Application of Computers and Operations Research in the Mineral Industry (APCOM) take place jointly in Tucson, AZ. On such an occasion it was thought appropriate to publish an anniversary volume which reviewed current practices and projected what might prevail as computer methods for the future. Thus was born the idea to publish Computer Methods for the 80's. The first planning meeting for this volume took place in Las Vegas, NV, during the 1976 annual meeting of the American Institute of Mining, Metallurgical, and Petroleum Engineers. It quickly became evident that no single computer method existed to solve most mining problems; rather, mining computer methods are generally tailored to fit unique geologic, mining, and organizational conditions. Hence a format which included both the theory and practice for each of the computer applications was adopted for this volume.

Jan 1, 1979

By Eugene V. Cilento, George B. Georgellis

The hypothesis that freshly-sheared quartz makes it more reactive in lung tissue than aged quartz was tested by its ability to stimulate superoxide anion (02-) release from single adherent pulmonary alveolar macrophages (PAM). Fresh quartz was prepared by grinding for 30 min and then used within 2 hr, while stale quartz was from the same stock but aged 15 days prior to use. Also, dipalmitoyl lecithin (DPL), the major constituent of lung surfactant coating the alveoli surfaces, was coated onto the particles. Release of 02- was measured after 40 and 180 min of direct contact with quartz dust (225 µg/ml). Fresh quartz was more reactive than aged quartz, as indicated by the 78 and 63% increase after 40 and 180 min, respectively. A time delay and suppression of 02- release was observed in the ability of the DPL- coated fresh or stale dust to stimulate PAM. These results supported the hypothesis that the natural process of surfactant coating of inhaled particles in the alveoli may play a role in their phagocytic removal by PAM.

Jan 1, 1991

By Jed H. (Original by) Mosgrove

Good mine ventilation starts at the drawing board. A coal mine will either be adequately ventilated or not, depending upon how good a job was done in the planning. Poor planning will not only result in inadequate ventilation, but may also lead to low productivity. A mine foreman cannot achieve high productivity while trying to maintain 4.2 ma/s (9000 cfm) of air at his last open crosscut.

Jan 1, 1981

By Stanislaw Nawrat, Waclaw Trutwin, Waclaw Dziurznski, Janusz Roszkowski

In recent years attempts have been made to fight open and intensive mine fires by the use of special extinguishers, which are able to produce great volumes of inert gases directed into the fire zone. These extinguishers are derived from turbo-jet engines used in aircrafts and adopted for operations in mine conditions. The purpose of this paper is to draw the attention to a computer simulation method, enabling studies of dynamical behaviour of mine ventilation processes disturbed by open fires, which are also influenced by measures taken during fire fighting actions i.a. the mentioned operating extinguishers. The first part of this paper gives an account of the principles on which the computer simulation program, concerning the non- steady mine ventilation process, the fire as a heat source and the extinguisher as a source of inert gas and moisture has been based. The next part of this paper deals with simplifying assumptions and the subsequent limitations of the derived simulation pro- gram. Finally, from an example of a computer simulation, the results will be presented and relations shown between parameters characterising the ventilation process during the fire fighting action.

Jan 1, 1997

By M. W. Rutland, E. Manev, R. J. Pugh

Data collected from several different fundamental surface chemical techniques were compared to study the interfacial interactions in the dodecylaminelmica flotation system. In the present study, the method used was the microinterferometric free foam film technique of Scheludko (1967) in which the stability, thickness and interfacial potentials at the air/dodecylamine solution interface were determined. These results were compared to previously published data, obtained from surface force measurements (Rutland et al. 1992), in which the interaction and hydrophobic adhesion (pull-off force) between molecularly smooth mica sheets in the amine solution had been reported. Also equilibrium contact angle measurements were used for comparison. The data was collected over a range of pH values and related to the batch flotation response of mica in dodecylamine solution. It was found that maximum flotation occurred at pH 8, but this did not correlate with the minimum in double layer interaction potential. However, it appeared to correspond with a tightly packed collector monolayer giving maximum hydrophobicity to the mica surface. Finally, from the extended DLVO theory, it was shown that heterocoagulation between the bubble and the mica could only occur, providing there was a very long range hydrophobic interaction force to counterbalance the repulsive van der Waals and electrostatic forces.

Jan 1, 1995

By E. Koufetzis

Rock mass classification systems are core elements of tunneling and empirical mine design worldwide. The Bauxite division of S&B Industrial Minerals S.A. decided to implement a rock mass classification system in order to provide mining engineers and supervisors of the underground mines, with guidelines of stability performance and with a complementary tool for the selection of the appropriate tunnel support. The back analysis system employed is based on visual observation of especially selected underground mine sites, representative of all rock types. This fact combined with the failure or success of the already existing support system, constitute the fundamental part of the work undertaken. The paper is divided into three main parts. In the first part the classification methods of Q, RMR89 and GSI are presented and the advantages and disadvantages of each method in connection with underground mining are indicated. RMR89 and GSI are conclusively selected for use, the main criteria for the selection being, the simplicity in use and the competency of the support system suggested for each rock mass category. The second part points out the methodology for measurements, the practical difficulties encountered during this process and the guiding principles followed, in order to avoid these problems. In the third part, the final conclusion of this project is demonstrated and the different rock mass categories are presented with their relative support recommendations, as they were applied and tested in all phases of the bauxite mines? exploitation. The generated methodology is being implemented by the site mining engineers, for validation and potential improvement.

Jan 1, 2008

By L. W. Saperstein, R. J. Sweigard, D. L. Simpson

Deep tillage is widely used as a means of alleviating excessive soil compaction. There has been some concern that the voids created by deep tillage may collapse before a more natural soil structure develops, resulting in recompaction subsequent to deep tillage A laboratory investigation was conducted to determine the feasibility of pneumatically injecting organic material into the voids produced during deep tillage in order to prevent any significant recompaction from occurring. Various amendments were injected into the soil during laboratory tests using a small-scale ripping and injection system. Measurements were made of selected soil proper Pies to evaluate the feasibility of this method.

Jan 1, 1994

By J. E. Gebhardt, J. A. Herbst, K. Y. Lee

Benefits of proper control of reagent usage in flotation circuits are typically improved metallurgy and savings in reagent costs. Improved metallurgy can mean more consistent product quality, i.e., final concentrate grade, better recovery of product values from the feed, or higher plant throughput at existing target recovery, and grade values. Flotation performance is sensitive to a variety of process disturbances which occur in operating plants, such as changes in flow rate, percent solids, size distribution. flotability of mineral species, etc. A way to handle these variations is to fully understand the dynamic flotation responses to disturbances and to implement a suitable control strategy to compensate for these disturbances. Depending on the objectives of the control system, various types of control strategies are available which employ different levels of refinement to achieve the desired performance. Typically, variables such as collector and frother dosages and reagent addition points can be manipulated to affect the performance of the circuit. In the case of sulflde mineral flotation, manipulation of the process electrochemical potential, in flotation and in grinding, offers another degree of process control. Because of the complex and interactive nature of flotation process variables, optimized reagent control requires consideration of all, or at least the most important, interactive variables of the flotation circuit. Model- based optimizing control provides a framework to handle the complex and dynamic nature of flotation reagent process control.

Jan 1, 1994

By Maurice Rey

The copper segregation process is designed to concentrate oxidized copper ores or mixed sulfide-oxide copper ores which are refractory to normal and cheaper mineral dressing or leaching processes. Such ores contain copper silicates or highly disseminated copper minerals in a gangue not entirely free from limestone or dolomite. Concentra¬tion by flotation is, under these circumstances, not possible and the acid-consuming constituents do not permit acid leaching. A high temperature treatment at 700-800°C, in the presence of a small amount of sodium chloride and of finely divided carbon, concentrates the copper into easily floated metal by a kind of reducing chloridizing roast. The sulfides, if present, are either oxidized in the heating stage and react like oxides or float with the metallic copper in the flotation step. The ores which have the aforementioned characteristics and which are high grade enough to pay for the treatment are scarce, so that the process has only a limited application. Theory of Copper Segregation Sodium chloride, reacting with water vapor and the acid gangue constituents, produces hydrogen chloride which reacts with the copper minerals. The copper is volatilized as cuprous chloride and immedi¬ately reduced on the coal particles by hydrogen emanating from the volatile matter of the coal and from the water-gas reaction. Hydrogen chloride is

Jan 1, 1985

By Francis W. Brown, Philip R. Hunt, Douglas N. Halbe

Refractory arsenopyrite ore from Western Mining Corporation's Lancefield deposit in Western Australia is treated by fluosolids roasting of a flotation concentrate followed by cyanidation of calcine and flotation tailings. The project development is reviewed from original testwork through circuit design, operating experience, and subsequent expansion.

Jan 1, 1990

By J. M. Dean, R. L. Grayson, R. D. Begley, G. L. Winn

Evidence has accumulated indicating that cultural change toward safer workplace behaviors is beginning to occur systematically in the coal industry. Through a range of programmatic mining company successes, enforcement and litigative actions, economic responses to competition and integrated efforts by federal and state agencies, a broader participation of safety and training professionals is being achieved to address prioritized workplace problems at mines. Small steps in workplace-related improvements have been realized already, but the trends in industry safety statistics, coupled with focused programmatic initiatives, indicate that more definitive and systematic steps are occurring to improve safe behavior in the workplace routinely.

Jan 1, 1998

By M. R. Nelson

Continuing experience in the Black Hills, South Dakota, indicates the persistence of several natural contaminants in mine waste effluents under circumneutral pH conditions. Selenium and arsenic are the most problematic environmental contaminants observed in these effluents. The contaminants are present in ore and waste rock as naturally occurring trace elements, and under the physico chemical conditions of the mine waste repositories are mobilized by oxidation and desorption reactions into infiltrating water. Characteristics of the mine wastes, waste repository construction, and Black Hills climatic conditions, indicate these natural contaminants may persist well into the future causing long-term mine closure liabilities, a difficult challenge to both mine operators and regulators.

Jan 1, 2003

By D. L. Schweyer, W. A. Munson, R. H. Hanewald

Discussed is the INMETCO processing of electric arc furnace (EAF) baghouse dusts from the specialty-steel and low-alloy industries. In addition, the INMETCO process has been modified to recover nickel, chromium and iron from many other waste materials including: •pickling solutions or filter cakes, •spent nickel and chromium plating baths, •carbon refractories from pickling tanks, and •superalloy wastes including baghouse bags. INMETCO is the only North American company presently capable of recycling nickel-cadmium batteries by high-temperature metals recovery. This process and the details of INMETCO's best demonstrated available technology (BDAT) test program are discussed.

Jan 1, 1993

By J. D. Miller

Fluid flow phenomena and therefore the flotation efficiency of air-sparged hydrocyclone (ASH) flotation are strongly dependent on operating and design variables such as air and slurry flow rates, underflow and overflow opening areas, percent solids of the feed, reagent levels, particle size and ASH length. Time-averaged multiphase flow characteristics, as determined by X-ray CT (described in a previous publication), are used to understand and explain the steady-state ASH flotation of quartz. A detailed parametric study of quartz flotation by a nominal 2in. diam. air-sparged hydrocyclone (ASH-2C) revealed the influence of these variables on the flotation response, which is discussed in terms of the multiphase flow characteristics. Thus, a phenomenological description of quartz flotation has been established to assist in the further development and utilization of the ASH technology.

Jan 1, 1996

By J. J. Krizek, A. H. Ditto

INTRODUCTION The Carr Fork property is situated in the Bingham Mining District located on the east slope of the Oquirrh Mountain range in Utah. The mine is adjacent to and lies west of Kennecott's Bingham Pit some 25 miles southwest of Salt Lake City. The Bingham Mining District contains one of the largest copper reserves on North America. Mineralization is associated with the Bingham stock which intruded through some 16,000 feet of sedimentary formations. Mineralization and a1teration zoning was developed radially from the Bingham stock with lower grade disseminated copper mineralization centrally located in the stock and adjoining quartzites. In addition, several garnetized limestone beds abutting the stock were also well mineralized. These skarns will be Carr Fork's initial mining target. Of the several limestone beds, only two, the Yampa and the Highland Boy have significant commercial interest at present. These beds which are 50 feet to 150 feet thick and are separated by 200 to 400 feet of quartzite were highly folded, thrusted and faulted, resulting in a dip variance from 20" to vertical. The predominant dip, however, is between 20" and 45" from horizontal. Quartzites surrounding the limestone beds were subjected to the same degree of tectonic activity with resultant intense fracturing and stress relief. The limestone beds which have a higher elastic modulus and which also experienced fracture healing during mineralization appear to have greater competency and strength than the quartzites. Four shafts nominally 3500 feet deep will provide access to the mine which will be a highly mechanized trackless operation, designed to produce 14,000 tons per hoisting day. First production is scheduled for the last quarter of 1979.

Jan 1, 1977