Search Documents

By David K. Ingram

The objective of this U.S. Bureau of Mines investigation was to characterize overburden response due to longwall mining. Subsurface strata and surface deformations were monitored during the mining of two adjacent, 900 ft wide longwall panels in southeastern Ohio. The panels were separated by a five entry, four pillar system (about 350 ft wide). The overburden thickness in the study area ranged from 214 to 280 ft, and the extraction thickness averaged 70 in. To delineate the geology of the overburden, six coreholes were drilled along a profile line extending across the two longwall panels. Multi-point borehole extensometers (MPBX) with eight-anchors were installed in six boreholes to measure subsurface displacements. The MPBX units were continuously monitored using a data logger. During the mining of the first panel, displacement occurred in a radiating pattern beginning just above the extracted area in the center of the panel and extending upward and outward towards the surface and margins of the panel. Overburden deformation did not project over the gate road entries. During the mining of the second panel, the MPBX's showed almost simultaneous displacement, indicating that the overburden began to move as a whole unit. Again, overburden deformation was confined to the immediate panel area. At both panels, overburden movement began when the longwall face was approximately 55 ft beyond the line of MPBX boreholes. Moreover, all ground movement was complete when the longwall face was approximately 200 ft beyond the line of MPBX boreholes. This paper discusses the results of the study and identifies the characteristics of overburden deformation.

Jan 1, 1986

By T. Tamagawa, S. H. Tabaian, I. Iwasaki, N. X. Fu, M. Kobayashi

A gaseous chlorination process for the hydrometallurgical treatment of a chalcopyrite concentrate was investigated. The overall process is visualized to consist of low-temperature chlorination -selective oxidation, followed by aqueous chloride leaching and SX-EW for producing electrolytic copper, elemental sulfur and ferric oxide. In this article, the chlorination phase of the process is described. Initially, the chlorination behavior of chalcopyrite concentrate micropellets was investigated using a small batch-type fluidized bed reactor. The optimum conditions thereby established were used in continuous chlorination tests. The chlorinated products thus prepared were used in the selective oxidation phase of the investigation.

Jan 1, 2000

By Karen Bolm, Floyd Gray, Ailiang Gu, Kerry Caruthers, Carlos Velez, Laurie Wirt, Douglas M. Hirschberg

Understanding sources of dissolved metals and transport characteristics of acid drainage is needed to assist land-use strategies in mineralized regions, particularly in the semi-arid southwestern United States. Water- quality samples were collected from mined and un-mined parts of the Patagonia and southern Santa Rita Mountains of southern Arizona from streams, springs, seeps, adits, alluvial wells, and bedrock wells. Water quality during base-flow conditions was compared with that *of runoff samples from infrequent winter and summer storms. The largest fraction of annual discharge in these ephemeral streams consists of storm runoff, although springs provide a steady source of low discharge base flow to numerous intermittent perennial reaches. Several abandoned mines in the northern Patagonia Mountains contribute acid and heavy metals to streams. During base-flow conditions in mineralized areas, natural springs and intermittent stream reaches produce acidity but the volume is typically low and acidity is often diluted or neutralized down gradient. Overland runoff contains low concentrations of dissolved metals and moderate acidity, however, stream waters were strongly acidified and metal-laden from contact with abundant pyrite-bearing stream sediments derived from erosion of waste-rock material in and along the sides of the stream channel.

Jan 1, 2000

By Klaus Schönert, Martin Botsch

In common high intensity magnetic separators, the magnetic particles are deposited on ferromagnetic matrices, such as expanded metals, steel balls or grooved plates, inserted into a strong magnetic field. The nonmagnetic material is flushed through the matrix chamber. Discharging the magnetic particles is only possible if the magnetic field is reduced to zero (e.g. high gradient magnetic filtration for the purifying of kaolin) or the matrix chamber is moved out of the field by a rotor (e.g. the Jones Separator). Therefore, these separators perform only in a batch or semicontinuous mode. A real continuous operation requirs transport of the deposited magnetic material to an outlet where it can leave the separation chamber inside the field. One possibility for accomplishing such separation and transport is through the use of a rotating induction body with a certain shape, such as a spiral.

Jan 1, 1995

By K. Rajamani, L. B. Hales

Much of the process control effort in the mineral industry uses proportional-integral-derivative controllers that require periodic retuning. Retuning hundreds of controllers typically employed in a single plant is a formidable task for the control engineer. Adaptive controllers offer an alternative to this problem, since they are designed to tune themselves. Four schemes of adaptive control-gain scheduling, model reference adaptive control, self-tuning regulator, and optimal adaptive controllers-are discussed with process examples. The control of a ball mill circuit with a multivariable self-tuning regulator is illustrated. This controller encompasses the advantages of the other three controllers and is applicable for a wide range of process variability.

Jan 1, 1988

Cost accounting information is used primarily for (1) planning, control, and performance evaluation; and (2) managerial decision-making. Incremental analysis is a tool for managerial decision-making. It is designed to estimate future financial performance, namely the benefits and costs associated with alternative courses of action. Decisions may be distinguished as pertaining to short-term or long-term activities. Long-term activities frequently focus on capacity decisions and the attendant capital budgeting processes used to quantify the financial effects of these decisions. Short-term decisions typically address short-range production quantity and pricing issues, outsourcing, selection of the optimal mix of products, inventory management, and the acceptance of special orders. This chapter addresses these short-term decisions.

Jan 1, 1999

By Jan M. Mutmansky, Y. J. Wang

In the mathematical analysis of electrical networks, the electrical devices are often modeled using idealized network elements such as current sources, voltage sources and resistors. An analogous approach is outlined for the modeling of mine ventilation networks, which can be considered nonlinear resistive networks. The proposed modeling technique uses the following five basic (nonreducible) elements: H, Q, D, R and N. These elements are characterized by their pressure gain or loss, their air quantity and their pressure-vs.-quantity relationships, each of which may be known or unknown. In addition to the definition of the basic elements, the necessary conditions for which there exists a unique solution are discussed. This is performed using theoretical developments derived from electrical circuit theory and illustrated in example networks. The proposed procedures are useful in the solution and characterization of mine-ventilation networks.

Jan 1, 1998

By Nick J. Miles, Gareth J. Brown

The degree of fragmentation of dispersed systems of brittle materials such as pulverised rock has been described by a fractal dimension i.e. the fragmentation fractal. This fractal dimension represents a power law size-frequency distribution, where, in this case, the size is defined as the square root of the projected area. The existence of a fractal dimension for the number-size distribution, of the progeny of failure event, is direct evidence for scale invariance of the fragmentation process. Since a fractal dimension infers that failure mechanisms operate on all scales it has been suggested that the fractal dimension is a measure of the fracture resistance properties of materials during fragmentation. In order to investigate this a range of rocks of varying fracture toughness were broken under similar levels of impact velocity in the dynamic tensile failure of single particles. The fragmentation fractals determined from the resultant particle populations, of the breakage experiments, were monitored and are discussed.

Jan 1, 1995

By Richard D. Christie, K. Jay Pillai

In the past, it was not unusual for coal preparation plants to discard fine run-of-mine coal. This practice has changed due to increasing quantities of fine material, improvements in beneficiation methods, and the need to recover revenue from these fines. It is in this context that the coal industry has increasingly been turning to froth flotation for fine coal beneficiation. Reagent schemes have been developed to promote coal flotation and to treat the resulting refuse material. While reagent technology has improved, however, most plants rely on manual control of reagent dosing and circuit operation. This often results in misuse of reagents, loss of coal recovery, and consequent loss of revenue. Fine coal circuit operations can be dramatically improved through automation. Intelligent process control systems are now in use which are capable of optimizing reagent usage, maximizing coal recovery, and minimizing chemical costs associated with refuse handling. This paper describes a type of control system currently used in preparation plants, and provides data and information on the significant improvements such systems can produce.

Jan 1, 1994

By C. Patrick

Annually, the US coal industry generates and must dispose of over 200 million st (180 million t) of coal refuse, expanding a major environmental problem. The purpose of this research was to investigate the feasibility of utilizing coal refuse as an aggregate in concrete. This paper reports on findings of the initial phases of a project to determine the viability of replacing traditional concrete blocks with refuse blocks for use in ventilation stoppings in underground mines. Refuse, collected from three active preparation plants in eastern Kentucky, was used as the primary as aggregate in the preparation of concrete cylinder. Stress-strain analyses on the refuse cylinders yielded compressive strengths of from 59% to 77 % of the control-group strengths. Low variability within the groups was found while significant differences between the groups existed. On-going determinations of the effects of weathering on the refuse cylinders is being conducted and will be completed in early 1995. The research results are favorable for the future direction of the overall project objectives.

Jan 1, 1997

By I. Longson

Maintaining control over underground environmental conditions in the United Kingdom is increasingly dependent on the contribution of underground booster fans. Given the recent trends of higher rates of production from a fewer number of coal faces with higher levels of mechanization and higher power consumption, the effect has been to place a greater load on the mine ventilation system. This has increased the scale of potential problems that may arise should any of the main ventilation control devices not perform at the required full duty. This is particularly true for underground booster fans. Major changes occur in the main ventilation parameters on the stoppage or restart of a booster fan which results in a temporary loss of environmental control. This paper analyzes the impact of such events and details a mathematical model thar has been developed for a single-mesh circuit containing a main and a booster fan. Predictions based on this simple model are presented and discussed with particular reference to the energy changes occurring within the ventilation system immediately following a booster fan stop or restart

Jan 1, 1995

By T. M. Barton

This paper presents several case studies in which a mechanics-based boundary-element program is used to back-calculate the surface subsidence associated with various panels at several northern Appalachian coal mines. The program used in this case study is called LAMODEL, which incorporates a frictionless, laminated overburden into a general-purpose displacement-discontinuity code primarily designed for calculating the stresses and displacements in coal mines or other thin-seam or vein-type deposits. In this paper, the program is used to calculate both the underground convergence and the resulting surface subsidence at five longwall panels and a room-and-pillar section. The fitted subsidence from the model is compared with the field measurements and analyzed. The results from this work show that the LAMODEL program is not as accurate as available empirical subsidence-predictive methods; the expected correlation between the geology and the optimum input parameters is not evident. However, for a mechanics-based program, LAMODEL does provide moderately accurate subsidence calculations, and it is one of a few programs that can even attempt to practically calculate both underground stress and convergence and the resulting surface subsidence.

Jan 1, 2000

By Z. C. Liu, F. F. Roxborough, Lin. B. B.

The size distribution of coal cut by a mining machine is an important performance factor. It is well established that the main machine system variable that affects product size is the depth of cut. In essence, the greater the amount of coal won by a machine cutting at shallow depths, the greater the proportion of dust and fines produced. Conversely, deep cuts produce less dust and a generally larger product size. When cutting with a rotating drum, as well as with a longwall shearer, the depth of cut always varies from zero in the vicinity of the roof and floor, where most of the dust and fines are produced, to a maximum at mid-drum level. In this paper, minimizing the amount of shallow cutting with a cutting drum is discussed, and the effects of the drum cutting and design parameters on cross-sectional cutting area per revolution are analyzed. This study shows the following: •more shallow cutting occurs during the entry quadrant of a cutting cycle than during pick exit; •the ratio of the projected area of shallow cutting to the total projected area of cutting by a single pick per drum revolution is virtually the same for drums of different radii (however, it decreases as the maximum depth of cut increases); and •for double drums, the use of unequal drum diameters can reduce the production of dust and fines, compared to using drums of the same diameter.

Jan 1, 1998

By Jorge Gutierrez C.

CODELCO-CHILE, the world's largest copper producer, began an integrated study of the informatics situation in the corporation at the end of 1980. As a result, a five years strategic Systems Plan was elaborated and approved by top Corporate management. Main points in this plan were: a systems architecture with information integration to the top level management; a higher degree of information technology in the production areas, an optional systems development resources utilization and a high profitability of the plan itself. During the study phase a series of theoretical definitions were fixed and used as a basis for the plan's design. A "common systems" approach was chosen as the development strategy instead of corporate systems or separate divisional efforts. Top management should be highly involved in the revisions of the plan, as well as qualified users should be chosen as project managers. The systems architecture should grant the information integration to the corporate level, in order to support an integrated planning and administration environment for the corporation. A total of 15 projects were defined, involving 570,000 man-hours and shifting the development efforts towards the production and production services areas. The paper presents a critical evaluation of the whole process, showing its good and bad aspects and a positive global balance. It also points some suggestions and hints to any corporation who wishes to get involved in a similar experience.

Jan 1, 1989

By P. Malozemoff

Discussion by P. Malozemoff I have no objection to using mathematics in the value appraisal of properties. The factor that is not emphasized in the paper is that very few important properties have a lifetime that reflects the initial ore reserves of the property divided by the rate of production adopted. In the majority of cases, major properties mine out several times the initial reserves. How much more will be mined out is not known, and only exceptionally gifted geologists can predict that additional reserves will be found. There is the further factor of metals price, which, over the long term, is not predictable. Another factor vitiating making calculations on initially established ore reserves is the speculative nature of exploration success. In my judgment, the life of a property, in addition to an established ore reserve, should include ample time for exploration to find additional reserves. The likelihood of additional reserves is based on the geological promise of the general area where the mine is established. This is especially important because of various risk factors associated with small orebodies, the economic life of which is about five to seven years. In underground mines, it is not economic to develop reserves beyond a certain depth, so the life of initially established reserves must be limited. In these cases, it is especially important to have a good geological understanding of the orebody and its continuity. To accommodate these concepts and present proof of economic soundness for a mining enterprise, a mathematical analysis should yield a life long enough to allow exploration and the development of additional reserves that would ensure a longer mine life and a more profitable result.

Jan 1, 1994

By K. K. Haramy, J. McDonnel

INTRODUCTION Primarily because of mining at greater depth, an increasing number of coal mines in the United States experience floor heave problems. In many instances, the floor heaves at a slow rate without causing health and safety related problems; only additional roadway maintenance and coal handling equipment are required. However, when rapid, massive heaving occurs, the safety of mine personnel in the vicinity is jeopardized. Extensive floor heave causes a redistribution of stress around the mine opening and can cause additional ground control problems. This paper presents an analysis of rapid floor heave in a deep western coal mine. The analysis is based on field measurements, laboratory data, and beam design theory. Factors affecting floor heave, such as mining-induced stress, mine opening size, entry orientation, mine geology, rock physical properties, and gas pressure, are considered. Examination of floor heave in the mine indicates that heaving is primarily caused by deformation of a soft floor member that is subjected to high mining-induced stress. Theoretical analysis of in situ floor stresses resulting from overburden loading indicates that floor failure will occur. The analysis is confirmed by visual observations of floor heave in the mine. Recommendations for mine layout and opening design to control rapid, massive floor heave under these conditions are also presented. MINE-FLOOR-FOUNDATION THEORY The floor stratum in a coal mine acts as a foundation to support coal pillars and artificial supports, thereby providing support to the mine roof. The overburden load, transferred through pillars and other supports, applies tremendous stress to the floor. Soil mechanics theories provide solutions for foundation design problems that apply to the mine floor. Based on foundation theory, vertical load on pillars causes high shear stress zones in the floor. If the floor is relatively weak, it may fail and dislocate upward into the mine opening. Strong roof strata that do not readily fail transmit most of the overburden load through pillars to the floor. Heaving may result, depending on the thickness and physical properties of the floor

Jan 1, 1986

By Chas. F. Jackson

INTRODUCTION This paper is one of a series dealing with mining methods and costs, prepared and published under the sponsorship of the US Bureau of Mines (USBM) and made possible through the cooperation of many mining companies in the US and foreign countries. The data presented have been obtained from papers previously published by the Bureau dealing with indi¬vidual mines, from the technical press, and from infor¬mation furnished by the mining companies. DEFINITIONS Top Slicing The term top slicing is commonly applied to that method of mining in which the ore is extracted by a series of timbered slices, beginning at the capping; the slice is caved, bringing down the capping to the floor of the slice; the succeeding lower slices are mined up to the overlying mat or gob, consisting of an accumulation of timber from the upper slices and broken capping, which follows the mining progressively downward (Fig. 1). The term has also come to be applied to the mining of ore bodies only one slice thick, by a series of tim¬bered slices one beside the other. The timbers are blasted out, bringing the capping down to the floor, suc¬ceeding slices being driven alongside those already caved (Fig. 2). In USBM classifications of mining methods, top slic¬ing has been placed under the heading caved stopes. The method differs fundamentally, however, from the cav¬ing methods of mining in which the breaking of the ore itself is accomplished by caving action induced by undercutting. In top slicing the ore is broken by the ordinary methods of drilling and blasting, and only the capping is broken up by caving. Main Levels or Haulage Levels Main or haulage levels are the main extraction levels on which the ore is hauled to the shaft. These levels and the shaft constitute the preliminary development of the mine.

Jan 1, 1982

By Dennis Molvik, Omar Fulton, Chris D. Breeds, Don Gonzales

The Tolt Pipeline No. 2, West Snoqualmie Valley project, is part of a water supply project linking the Tolt reservoir in East King County to the City of Seattle through a nominal 2.13 m (7-ft) inside diameter conveyance. Receipt of the National, 2002Microtunnel Award provided recognition of the many challenges overcome by this project. Baseline conditions revealed in the Geotechnical Documentation included over-consolidated glacial deposits, landslide and alluvial deposits, artesian water, boulders up to 36-in in diameter, logs, heaving sands, and liquefiable soils beneath the river. Schedule constraints associated with setting the shafts in the floodplain of a salmon bearing river and the fickle performance of the river during those times it was not supposed to flood added to the challenge.

Jan 1, 2003

By David R. Quigley, Patrick R. Dugan

First reports of microbial coal solubilization appeared in the early 1980's (Fakoussa, 1981; Fakoussa and Truper, 1983; Cohen and Gabriele, 1982). These degradations, which occurred at ambient temperature and pressure, resulted in a dark brown to black viscous liquid and required days to weeks to occur. Rates and degrees of coal biodegradation varied from coal to coal. Hard coals were not extensively degraded (5-7%) while low-rank coals such as Leonardite, a sublignite, were completely solubilized. A correlation between degree of weathering or oxidation of coal and the coals susceptibility to biological attack was observed. This led to oxidative pretreatments as a method to enhance microbial degradation of coal (Strandberg and Lewis, 1986). Products of microbial degradation of coal are water soluble solids that do not have significant solubilities in organic solvents (Wilson, et. al., 1987; Quigley, et. al., 1987; Quigley, et. al., 1988a). Solutions of solubilized coal did not separate or form precipitates which suggested that they were true solutions and not colloidal suspensions. Biosolubilized coal contained more oxygen than starting material suggesting that microbial attack of coals involved oxidative cleavage of carbon-carbon bonds. This small change in oxygen content was the only change observed in coal structure during the biosolubilization process. Many coal solubilizing microorganisms have been isolated. Some are lignin degrading organisms such as Phanerochaete chrysosporium and various Streptomyces species (Gupta, et. al., 1988; Wilson, et. al., 1987). This was not unexpected since the structures of lignin and low-rank coals are similar. These organisms produce an enzyme complex, ligninase, that utilizes hydrogen peroxide to oxidatively cleave the bond between a and ß carbons of an aliphatic chain bound to an aromatic nucleus. Another important organism is Trametes versacolor (syn. Coriolus versacolor, Polyporus versacolor). Even though this organism produces a ligninase (Dodson, et.al., 1987), coal solubilization has been attributed to the enzyme laccase (Pyne, et. al., 1987). Laccase utilizes molecular oxygen to oxidatively cleave a - ß bonds using a mechanism similar to that observed for ligninases (Kawai, et. al., 1988). Other coal solubilizing microorganisms have been isolated from coal outcrops (Ward, 1985; Ward, 1988), but enzyme activities responsible for coal solubilization have not been identified. Research at the Idaho National Engineering Laboratory has focused on those mechanisms involved in coal biosolubilization. An

Jan 1, 1989

By Richard W. Kimball, Fred B. Estep, Dwayne E. Easterling

This paper discusses the overall challenges to construct a 15,125.7 m (49,625 LF),wastewater drainage tunnel in Cobb County, Georgia by a joint venture of Gilbert Southern Corp. and S.A. Healy Co. and a construction manager Parsons, with Jacobs Associates as a subcontractor. The goal of the project is to provide wastewater retention during peak usage and is connected to a treatment facility near the Chattahoochee River. The primary component of the project is the TBM-driven hard rock tunnel. Additional works include drill and blast areas; four intake interceptors, two construction shafts and a 33.5 m (110 ft), diameter pump station shaft.

Jan 1, 2003