Search Documents

By James P. Rider, Robert P. Vinson, Fred N. Kissell, Jon C. Volkwein, Gregory J. Chekan, Jay F. Colinet

The Thermo-MIE personal DataRAM dust monitor (pDR) is a light-scattering instrument approved for use in gassy underground mines by the U.S. Mine Safety and Health Administration (MSHA). However, the use of lightscattering monitors has been inhibited by concerns about inaccurate readings resulting from changes in dust size distribution and composition, as well as concerns about the impact of moisture in the mine air. Because of this concern, the National Institute for Occupational Safety and Health (NIOSH) has evaluated the pDR using available data from laboratory tests and mine surveys. The data show that accuracy can vary widely from test to test and mine to mine. In most cases, the results can be improved by using a companion gravimetric measurement to adjust the pDR data.

Jan 1, 2005

By Felicia F. Peng, Lili Li

The dispersion model of nonideal flow was applied to describe the hydrodynamic state within the flotation column. Residence time distribution (RTD) data of a laboratory flotation column were measured to determine the parameters of the model. The effects of operating variables and column geometry on the Peclet number which reflects the extent of axial dispersion were investigated and a semi-empirical expression of Pe was formulated. The dispersion model was validated for the column flotation of ultrafines coal. Under the conditions of sufficient aeration rate and frother addition, a good agreement between the measured recoveries and predicted data was obtained. The dispersion model with first-order flotation rate process of the flotation column developed in this study is useful in predicting the collection zone recovery of fine coal, and for the flotation column scale-up.

Jan 1, 1995

By Wayne A. Ericson, Kirk S. Davis, Cornelis Winkler

BCI has developed a chemical process known as Ecophos® for the multi-industrial Pine Level Project in DeSoto County, Florida. Approximately 85 percent of the phosphogypsum at Pine Level will be converted to a very clean gypsum. The remaining 15 percent, including impurities plus some quartz tailings sand, constitutes what is termed redigestion solids. BCI has developed an alternative to the practice of disposing phosphogypsum in large above-ground impoundments. The proposed disposal method consists of mixing the redigestion solids with clays and reacting the mixture (leached tailings) with lime prior to disposal into the mine excavations as a reclamation soil material. Leachate water quality testing using lysimeter equipment indicates that the pore water associated with neutralized leached tailings meets maximum contaminant levels set for the drinking water standards of radium and selected primary metals.

Jan 1, 1992

By H. E. M. N. Moursy, M. N. Ahmad, C. R. Holland, G. M. Walker, R. D. Chandler

This work describes the effect of process parameters on the acidulation of Moroccan phosphate rock using nitric acid, i.e., the nitro-phosphate process. A series of bench scale experiments were conducted, using a stirred tank reactor (STR) system, to investigate the chemical reactions involved and optimum conditions for the formation of nitro-phosphate fertilizer. The effect of reaction time, temperature, mixing speed, acidulation ratio, and acid concentration were investigated, and were found to have an effect on the dissolution of P2O5 from the phosphate rock, using nitric acid. An increase in nitric acid concentration resulted in an increase in P2O5 dissolution, however, the dissolution was also found to be a function of acidulation ratio. A nitric acid phosphate rock ratio of 4:l ensured 90% dissolution for nitric acid concentration > 30%.

Jan 1, 2002

By B. J. Arnold

A coal's size distribution clay content and moisture content can affect its handling behavior. But the combined effects of these properties and the effects of other properties are not known. Research underway at CQ Inc.'s (formerly EPRI's) Coal Quality Development Center (CQDC) and at Iowa State University (ISU) will answer these questions as part of a four year project to develop a coal handleability index for utilities to use when specifying coals. This paper will present preliminary data from the first year of the project, which focused on obtaining data on the chemical and physical properties of carious coals and their measured handling properties. Additionally, size, ash and moisture analyses and shear test data for several coals used at one power plant will be presented along with correlations between these physical and chemical properties and the measured handling properties. These data lead to the conclusion that while moisture content is the most important variable, the amount of -44 µm (-325 mesh) coal fines is a significant factor in determining coal handling behavior.

Jan 1, 1992

By S. Mason

Many organizations are realizing that continual improvement in health and safety relies on addressing the potential for various forms of human error. Of these, rule violations are often the most frequent form associated with accidents. These occur when an individual (or individuals) deliberately contravenes established and known safety rules. They have been associated with up to 90% of the accidents and other incidents in some industries, and yet they rarely receive the systematic attention they deserve in the promotion of safety. This paper presents underlying motives that cause violations. These can vary significantly from mine to mine and from job to job. Managers need some measure of the attitudes of the violators to determine the underlying motives behind the violations if they are to determine effective strategies for promoting safe behavior. Questionnaires form the starting point to address attitudes and the motives behind rule violations. The choice of the most suitable questionnaire, how- ever, will vary from organization to organization. Guidelines on the choice of questionnaire are offered.

Jan 1, 2000

By J. F. Cuderman

In situ experiments at the Department of Energy's Nevada Test Site (NTS) have extended the technology of propellant-based fracturing to include liquid- filled, uncased boreholes. Previous work had developed the technology for liquid-free, uncased wellbores. Test results show that fracturing behavior is considerably more complex in liquid- filled boreholes than in the liquid-free case. Compared to liquid-free boreholes, liquid-filled boreholes have faster pressure risetimes and lower peak pressures, large hydraulic-type fractures propagating several meters beyond the end of the test zone, numerous oscillations in the pressure history, and variable types of fracturing within a single test region. Multiple fracturing is initiated in the wellbore of a fluid-filled borehole when the proper propellant mixture is used but, unlike fluid-free wellbores where up to eight fractures propagate, only one to three hydraulic- and/or shear-type fractures propagate. Hydrodynamic effects involving liquid compression during borehole pressurization appear to be responsible for the differing phenomena observed in fluid- filled boreholes.

Jan 1, 1986

By Patricio A. Espinoza, Aldo Casali, Cristian Ardiles, Guillermo González

Cluster analysis is used to design grade soft-sensors in a rougher flotation plant and a ball mill overload soft-sensor. Soft-sensors are virtual sensors which either replace unavailable actual sensors or infer measurements for non existing sensors. In the case of the grade soft-sensors clustering serves to determine clusters of related operating points. To each cluster there corresponds an ARMAX model structure whose parameters are estimated using only the points in the corresponding cluster. Thus a much better correlation is found than if all the data points were used for a global model. The problem of identifying clusters when the measurement of the real sensor is not available is addressed. In the case of the overload soft-sensor, variables were selected which are related to overload, either from a phenomenological point of view or according to operator experience. Different clusters are formed, some of which are identified as determining an overload condition or a possibility of such condition. Each of these clusters has a set of operating conditions which suggests the corrective action to be taken when necessary. Both kinds of soft-sensors are tested with industrial plant data and promising preliminary results are obtained.

Jan 1, 1995

By Jean-Michel Rendu

The semivariogram is one of the most important tools available to the geostatistician for the analysis of mineral deposits. To be complete, a semivariogram study must include a minimum of three parts which are highly interdependent. These are: calculation of the semivariogram, mathematical modeling, and geologic interpretation. The known factors and conditions which controlled or influenced the distribution of mineralization within the body being studied should be considered in the analysis .of the semivariogram. The presence and characteristics of successive phases of mineralization, the chemical and physical properties of the host rocks and the mineralization should all be considered. This requires close and continued communication between the geologist and the geostatistician prior to and during the semi-variogram study. Geologic stationarity is needed if meaningful semivariogram results are to be obtained. The first step is, therefore, to determine whether the mineralization can be analyzed as a whole or if different geologically homogeneous sections must be defined and evaluated separately. Different methods can be used to calculate an experimental semivariogram from known sample values. The method chosen will depend not only on the anticipated and actual statistical properties of the deposit, but also on its geologic characteristics.

Jan 1, 1982

By M. M. Nash

Since the late 19th Century, scholars have been concerned about finding proper methods of managing business. The search seems to be taking us full-circle to the time and motion studies of Taylor (Horn, 1987). It wasn't until the late 1970's, however, that systematic investigations were made in the mining industry. One of the first was a study by Sanders, Patterson, and Peay (1976). That project explored the relationship of attitudes and safety. Peay, Atkin, and Goodman (1977, then reviewed the whole area of Organizational Development, including the so-called Rushton experiment.

Jan 1, 1988

By J. Simmons, P. Ziemkiewicz

Acid-Base Accounting (ABA) is an analytical procedure that provides values to help assess the acid-producing and acid-neutralizing potential of overburden rocks prior to coal mining and other large-scale excavations. This procedure was developed by West Virginia University scientists during the 1960s. After the passage of laws requiring an assessment of surface mining on water quality, ABA became a preferred method to predict post-mining water quality,and permitting decisions for surface mines are largely based on thevalues determined by ABA. In order to predict the post-mining water quality, the amount of acid-producing rock is compared to the amount of acid-neutralizing rock, and a prediction of the water quality at the site (whether acid or alkaline) is obtained. We gathered geologic and geographic data for 56 mined sites in West Virginia, which allowed us to estimate total overburden amounts, and values for maximum potential acidity (MPA), neutralization potential (NP), net neutralization potential (NNP), and NP/MPA ratios for each site based on ABA. These values were correlated to post-mining water quality from springs or seeps on the mined property. Overburden mass was determined by three methods, with the method used by Pennsylvania researchers showing the most accurate results to actual overburden mass. A poor relationship existed between MPA and post-mining water quality, NP was intermediate, and NNP and the NP/MPA ratio showed the best prediction accuracy. In this study, NNP and the NP/MPA ratio gave identical water quality prediction results. Therefore using NP/MPA ratios, values were separated into categories: <1 should produce acid drainage, between 1 and 2 can produce either acid or alkaline water conditions, and >2 should produce alkaline water. On our 56 surface mined sites, NP/MPA ratios varied from 0.1 to 31, and six sites (11%) did not fit the expected pattern using this category approach. Two of eight sites with ratios <1 did not produce acid drainage as predicted (the drainage was neutral), and four of 40 sites with a ratio >2 produced acid drainage when they should not have. These latter four sites were either mined very slowly, had non-representative ABA data, received water from an adjacent underground mine, or had a surface mining practice that degraded the water. In general, an NP/MPA ratio of <1 produced acid or neutral drainage sites, between 1 and 2 produced mostly alkaline drainage sites, while NP/MPA ratios of >2 produced alkaline drainage with a few exceptions. ABA is a good tool to assess overburden quality before surface mining and to predict post-mining drainage quality after mining. The interpretation from ABA values was correct in 50 out of 52 cases (96%), excluding the four anomalous sites, which had acid water for reasons other than overburden quality.

Jan 1, 2003

By Rong Guo, Qi He, Jinsuo Zhang

"Coal mine ranks No.1 among the 6 major high-risk industries, so it is no doubt that the senior managers in the coal mine bear more stress than other industry executives. The massive working stress results in serious influences on the physical and mental health of the senior managers of coal mine, which might also induce the safety risk in the coal mine. Therefore, to evaluate the senior managers’ working stress and put forward strategies of mitigating the stress is of great theoretical and practical significance in improving the physical and mental health of the senior managers and reducing the safety risk in the coal mine. The research on the working stress has been made in the western countries for almost 50 years, China began the research in the mid and late 1990s, the research is spread across multiple industries including education, medical treatment, computer and aviation. However, there is little research on the senior managers’ working stress of the coal mine, so the available literatures are few. In the paper, we, based on the working stress model of Robbins and through questionnaire survey, analyze the element composition of the senior managers’ working stress of the coal mine; then, we construct the evaluation indicator system of the senior managers’ working stress of the coal mine based on the individual factor, organization factor and environment factor; after that, we determine weights of each evaluation indicators by using the improved triangular fuzzy number weight method, and set up the evaluation model of the senior managers’ working stress of the coal mine on the basis of the fuzzy comprehensive assessment method. At last, in accordance with the model, we evaluate and analyze the working stress for the senior managers of some typical coal mines, and diagnoses the major sources and intensities of the senior managers’ working stress, and then propose corresponding strategies of mitigating the stress."

Jan 1, 2017

By Subhash B. Bhagwat

No economic activity would take place without human ingenuity, driven by our needs and wants. Economic activity is made possible by the energy from fossil and other energy sources, our technological hardware, the buildings and infrastructure made from materials such as metals, plastics, wood, water, and numerous industrial minerals. Industrial minerals are difficult to define; however, they generally include utilitarian minerals other than metals and fuels. Some of the industrial minerals form an exception to this categorization and, as explained elsewhere in this book, belong to more than one category because of the manner in which they are used. Industrial minerals are so numerous, and their applications so ubiquitous that they often do not receive the attention given to metals or fuels. Nevertheless, without industrial minerals, many of our most fundamental economic activities such as construction of our cities and towns, control of floods, transportation of our people, the search for minerals, the smelting of metals, and the delivery of supplies of clean water would be impossible. How then do we assess the economic importance of such a variety of materials lumped together under the general designation of industrial minerals? The price per ton or the total amount consumed do not satisfactorily explain the relative value of these materials to the economy. For example, the current price of limestone is about $5/t and the price of fluorspar is about $190/t. However, nearly 1.1 Gt of limestone, valued at about $5.5 billion, are consumed in the United States annually, compared with 590 kt of fluorspar, valued at about $1 12 million. It would not, however, be accurate to conclude that the mineral with the higher total value is always more economically important. Many other questions must be answered before making judgments of this type. These questions include how many people are employed in the production, processing, and distribution of the mineral? How is the mineral used? Is it partly or entirely imported? Where do the imports come from? How is the mineral transported? Is the mineral considered critical to national security? Is there a substitute material available in case the mineral supply is interrupted? Where would the substitute be produced? What would be the basic material from which the substitute will be produced? Even when these questions have been answered satisfactorily, the economic importance of the mineral is not completely known until the consuming sectors are studied as well. For example, even though the manufacture of fighter aircraft is vital to the national security, it employs only a fraction of the number of people employed in the housing and construction industry or the automobile industry or the appliance industry. Mineral commodities consumed in these latter sectors of the economy are more significant than those consumed in the production of fighter aircraft, because nearly two-thirds of the Gross Domestic Product (GDP) depends on the purchasing power of individual consumers. In comparison, the entire defense budget accounts for only 6% of the GDP. There is no easy way to present the importance of industrial minerals to the US economy because most minerals have diverse applications and products made from industrial minerals often con- tribute to the production of other goods and services. One way of highlighting the value of a mineral would be to relate it to the GDP reported by categories such as construction, machinery, stone, clay and glass products, electrical and electronic equipment, paper and allied products, and chemicals and allied products. These GDP categories represent industries fundamental to the economy totaling $644 billion, or about 12% of the GDP in 1990. However, these categories are not convenient for discussion of the many minerals that are used in our complex economy. In a general way, minerals are the 5% of our economy that make the other 95% possible. This chapter, therefore, discusses a selected few industrial minerals to illustrate their importance to various sectors of the economy.

Jan 1, 1994

By H. J. Zhang, W. Wui

With the adoption of market-oriented economic policies, Chinese non-ferrous metals industry has gained remarkable progress. The continuously increasing domestic demand for non-ferrous metals, however, calls for more import of raw materials in short supply, such as copper concentrate and bauxite. As an alternative for balancing the shortage and assurance of more stable mineral supply, direct investment in oversea mining project has come to the agenda. This paper discusses the computer-assisted method used for evaluation and comparison of potential mining projects.

Jan 1, 1996

By Daniel J. Kennedy, George W. Klinowski

A significant portion of each mine is ventilated with the help of auxiliary fans delivering fresh air to the faces of its developing headings via flexible or rigid ducts. Quality and volumes of air delivered to the blind working faces are essential for creation of safe and acceptable conditions for employed crews. Well designed and properly maintained delivery systems are necessary in each mine. The Cape Breton Coal Research Laboratory, part of the Canada Centre for Mineral and Energy Technology located in Sydney, Nova Scotia, Canada, developed a tracer gas based technique which provides fast and accurate evaluation of any auxiliary ventilation system performance. In addition, important information about the system&apos;s behaviour is gathered which can be used for designing a similar system in comparable conditions.

Jan 1, 1989

By J. Alton Burks, Robert R. Stein

This paper focuses on the noise exposure levels of miners employed on longwall production faces. Along with the increased production from longwall units has come the potential for greater noise exposures. Typical noise levels are given for the various noise sources that are present on modern longwall faces. Exposure times have typically increased since the introduction of longwall technology in this country. Representative exposure times and patterns are analyzed. Possible solutions are presented for generalized cases. Engineering controls developed by the Bureau of Mines are explained and their potential effectiveness is calculated for the cases presented. The role of hearing protectors in an overall hearing conservation program is also investigated. Recent research performed by the Bureau suggests that the actual performance level of muff -type protectors may be less than the manufacturers ratings under certain circumstances. The use of muff- type protectors is discussed and analyzed with respect to their use on longwall operations.

Jan 1, 1992

By T. M. Dyhr, T. E. Wilson

Although environmental management costs during mine operation depend on the size, type, climatic and geochemical conditions of operation, general cost categories are identified and mean values, as a percentage of total operating cost, are determined for coal and non-coal surface and underground mines (medium-size) with on-site beneficiation and tailings disposal facilities. Cost trends are charted from 1963 through the present.

Jan 1, 2004

By J. A. Frew, G. I. Orrock, R. M. Glen

The zinc flotation circuit was sampled to provide sized information on its metallurgical performance. A good balance was obtained and the roughing, scavenging, cleaning and regrind sections were assessed. Substantial losses of sphalerite occurred in all sizes. The limitations were poor recovery in the cleaning section which resulted in substantial recycling of 15-30µm sphalerite and iron sulphides, and inability to float +38µm sphalerite in the roughers. Regrinding increased sphalerite recovery by 7% with no loss in grade. Liberation measurements enabled balances for six size fractions to be calculated and the role of liberation on the metallurgical performance was assessed.

Jan 1, 1993

By M. Josick Comarmond, John J. Jeffery, John W. Bennett

Oxidation rates of sulfidic mine wastes measured at a range of size scales have been collected from a number of sources. The results suggest that well-designed laboratory columns, under controlled conditions, provide comparable information on oxidation rates to that obtained from field test piles. It has been found in the cases presented that laboratory measurements of oxidation rates of a particular material type can be applied with confidence to the same materials in the field. It is recommended that a further study be undertaken to measure the time-dependence of the oxidation rate for a range of particle sizes and different materials. This study would provide measurements against which models of oxidation rate as a function of time and particle size can be tested, to give confidence in the use of models to describe dump behaviour in the longer term.

Jan 1, 2000

By Carl G. Schwenk

Rusk County is located in the northwestern portion of the state of Wisconsin, roughly 130 miles east of Minneapolis (Figure 1). The topography is generally flat with dairy farming the principal activity. Forest and swamp lands are common, as well as pasture and cultivated ground. Rusk County falls near the southern terminus of the Precambrian Shield and is covered by a thick layer of glacial drift. Outcrops are quite rare, but the few available exposures indicate that the subsurface is comprised of steeply dipping metamorphosed volcanics and sediments of Early Proterozoic age. A thin section of flatlying Cambrian sandstone is sometimes found directly under the glacial till. The depth to Precambrian basement has been recorded to be as great as 150 feet beneath the surface.

Jan 1, 1976