Search Documents

By Murdoch Mackenzie

"Organic Polymers used as gangue depressants are classified according to their chemical structure. Absorption mechanisms for these reagents at the mineral - water interface are reviewed. The method of selecting these reagents for a particular flotation system is discussed. Details are given of methods of reagent solution make-up and distribution. Plant addition policy is reviewed.”

Jan 1, 1986

By Lynton S. Land

Representative collections of recent dolomites, and of samples concentrated by leaching-out of coexisting magnesian calcites, provide grounds for appraisal of the compositions and cation ordering in recent dolomitized sediments. Unit cell volumes for near-stoichiometric compositions exceed those of ordered dolomite and increase as the departures from regular cation order became more pronounced. Infrared absorption maxima of disordered examples occur at perceptibly lower frequencies. Stable isotope ratios indicate that best ordered examples formed in highly saline environments. Present observations are qualitatively reconciled with data from synthetic products described by other authors.

Jan 1, 1972

By W. W. Koczkodaj, J. Partyka

Beat exchange in an open air-water system is considered. The system incorporates a vertical cooling tower, and a horizontal multi-stage spray chamber with unlimited number of stages. Mixing of two streams of both water and air is permitted. A spread-sheet implementation estimates temperatures of outgoing water and air for given mass flow of water and air, factor of merit for heat exchangers, barometric pressure, wet- and dry-bulb temperatures, and the temperature of incoming water.

Jan 1, 1987

By R. P. King, S. Middlemiss

A method is developed to convert a measured distribution of fracture energies to the equivalent work index. The method assumes that the energy required to grind the material from the feed size distribution to the product size distribution is equivalent to the sum of the impact energies that are required to reduce the feed material by successive single impacts to the required product size. The method was tested by measuring the fracture energy distributions for quartz and comparing the resulting calculated value of the work index with the work index for this material measured using the conventional Bond laboratory procedure.

Jan 1, 1998

By Dale J. Sadowski, Richard J. Switalski, Kyle R. Ott

This paper discusses design and construction aspects of shaft construction through rock saturated with petroleum hydrocarbons (crude oil). During the subsurface exploration phase for design of the Hilltop Interceptor project in Cleveland, Ohio natural crude oil was encountered at depths between 6.1 and 61 m below ground surface. The oil-saturated Euclid sandstone contained up to 12,000 mg/kg total petroleum hydrocarbons (TPH), various volatile organics, and had flash points as low as 18.9°C. Interceptor hydraulic design required that construction of access and/or drop shafts penetrate the layer of petroleum hydrocarbon saturated rock. This led to the design of a special lining and some special handling procedures for the excavated material.

Jan 1, 1995

By C. D. Elifrits, N. B. Aughenbaugh

Introduction Federal and state laws enacted to regulate coal mining and the accompanying public concern about the adverse effects that mining might have on land use have focused much attention on the subsidence of the land surfaces over underground mines. Some questions asked are • Will abandoned mines subside in the future even though they have exhibited no surface adjustment to date? If so, when will subsidence take place? • Can a specific surface area be affected by subsi¬dence more than once? • What surface form will the subsidence feature take? • Is there any way to predict when subsidence will occur and end? An attempt is made here to address these questions insofar as it is possible with available data and experience of evaluation of subcritical extraction conditions. Mining that results in subsidence features can be classified as supercritical, subcritical, and critical with respect to the minimum span lengths of the worked-out rooms (Fig. 1). A complete basin will not develop fully immediately over subcritical conditions because the span lengths of the entries are less than the critical dimension (Wardell, 1983). Passageways, entries, and room-and-pillar panels are all included in the subcritical category. Because of the short span lengths, subcritical mining conditions tend to be stable over the life of the mine unless adverse geologic conditions exist (Gray et al., 1974; Dunrud, 1976). Various roof control and support procedures are employed to maintain entry stability during mining. Little information exists concerning the time factor of subsidence over areas of subcritical extraction. Data that have been collected relate to longwall mines, whereby the cavity sizes are designed large enough to induce caving behind the working faces so that complete subsidence at the surface occurs within a short period of time. The UK's National Coal Board (1975) has reduced the enormous amount of data it has collected to empirical correlations and has published these correlations in its Subsidence Engineers Handbook. The handbook states that "None of the foregoing remarks applies to pillar and stall working," with respect to the section discussing the time factor of subsidence caused by longwall mining (National Coal Board, 1975, p. 40). To understand and evaluate how time relates to subsidence above room-and-pillar mines, one must first recognize how mine cavities deteriorate and fail. The propagation of failure to the surface must then be studied, and, finally, the failures that are manifest at the surface in the form of depressions accompanied by both compressional and tensional movements must be investigated. Failure of mine cavities Any cavity beneath the earth's surface represents a condition of nonequilibrium and tends to close with time. Failure of cavities in a subcritical mine can be classified as failure of the roof, failure of the floor, failure of the supports (pillars, cribs), and elastic rebound of the rock. One mode of failure may dominate, but generally combinations of the four will occur. Also, initial instability of geologic materials and structural features and in situ stress may be unknown factors that can contribute to cavity failure. Roof failure is the most obvious opening stability problem in most operating mines. The bridging capabilities of the roof rock are dependent on the rock's material strength, geologic discontinuities, and reaction to humidity changes in the air of the mine. This type of failure may vary in magnitude from gradual flaking to massive roof falls. Mine floor instability can be manifest in the form of a general heave over a broad area or of individual pillar punching. The weaker and thicker the immediate floor material, the more prone a mine is to experience floor problems. Water seeping into an area can soften the underclay, reduce its bearing capacity, and precipitate failure of support for the overburden.

Jan 1, 1987

By Frank W. Bowdish

During the early 1960's, a method was developed for refining sand from the Arkansas River to produce a feldspathic product that was proposed for use in making colorless glass. Because of the need for chemical uniformity, a cooperating glass manufacturer specified certain ranges of percentages for each chemical constituent of the sand. These specifications were met by fulfilling the single requirement that alumina vary by no more than 20.1 percent from the specified value. This translated to a total variation of only about 1 percent in the feldspar content of the mixed quartz-feldspar products. Because the feldspar was lighter than the quartz, the average density of refined sand varied depending on composition. Densities, determined to five significant figures, of several samples were correlated with their chemical analyses, and the correlation could then be used with density determinations to more reliably indicate compositions than by chemical analyses only. The effects of several variables on the composition of refined sands were studied. There was a regular variation in the proportion of feldspar with screen size. A series of samples with their natural size distributions were more nearly uniform in composition than the same sands after screening and recombination. The screening and recombination process was done so that the sands had identical size distributions. Variations in the refining showed little effect on composition. A pile of flow-back sand from a construction sand washer was found to be severely segregated. However, samples taken from many points in the river near the sand plant and from the flow-back discharge pipe over several weeks very nearly met the uniformity specification. If care was taken to avoid segregation either before or during processing, it should be possible to meet the uniformity specifications for a feldspathic glass sand.

Jan 1, 1978

By A. Arik

The accurate estimation of mining-block grades continues to be a challenging task for ore reserve practitioners. The estimation method used and the variability of the mineralization in the deposit are two factors that affect the accuracy of the estimates. The objectives of this study are to determine how different estimation methods perform on a given deposit and to determine the impact that the nature of the mineralization has on the results. A comparison of several estimation methods for prediction accuracy is performed based on conditional simulation results.

Jan 1, 2002

By A. I. Arol, I. Iwasaki

Clay minerals adversely affect the selective flocculation of iron ores. The effect of montmorillonite on a hematite-quartz mixture was studied. Montmorillonite, particularly in the presence of Ca++, caused indiscriminate dispersion of the pulp. Three possible mechanisms were postulated, namely, card-house structure formation, adsorption of dissolved species from montmorillonite, and montmorillonite- hematite interaction. It was determined that hetero- coagulation of montmorillonite on hematite was responsible for the behavior. Flocculation tests, montmorillonite abstraction tests, starch adsorption tests, zeta potential measurements, and surface analysis techniques were used to ascertain the montmorillonite-hematite interaction and to account for the manner in which it affected selective flocculation.

Jan 1, 1987

By Yongqin Zhang

A single bubble released into surfactant solution first accelerates, reaching a maximum velocity then decelerates to reach a terminal velocity. Modeling this "velocity profile" is fundamental to understanding the motion of bubbles in flotation systems. This contribution considers the terminal velocity. Modeling is by a combination of the Navier-Stokes equation for flow around the bubble and the Marangoni effect induced by surfactant on the bubble surface. Numerical simulation is shown to agree with experiment for bubbles in pure water and surfactant solutions.

Jan 1, 1999

By D. Lelinski, X. Nie, J. D. Miller, J. Hupka, K. Bukka

A preliminary characterization of soil components contaminated at a low level (7 nanocuries per gram) with toxic/radioactive metals has been carried out. Most radioactivity and metals content were present in the minus 100 mesh (<150 µm) size fractions. None of the size fractions examined qualified for uncontrolled disposal at dump sites, thus all material would have to be moved to discharge-controlled landfills. The metal content of the sample was below the limits for economical recovery, therefore eventual processing would be dictated by environmental concerns.

Jan 1, 1992

By Gabriel E. Zárate, Juan C. Guzmán

In Chile there are significant amounts of gold in flotation tailings that could be recovered, being heap leaching the most promising alternative. In order to determine the feasibility of treating these tailings by this method, a detailed study is carried out using 4 representative samples. After defining the best conditions an economic evaluation is done for a plant treating 200 tpd, sensibilizing with respect to parameters such us gold price, tailing grade and capital costs. The results show that it is technically feasible treat these gold tailings by heap leaching with gold extractions over 70 %. It is also economically feasible for gold grades higher than 0.5 g/t and gold prices over 350 US/oz.

Jan 1, 1987

By Antonio Peralta, Guillermo Dante Ramírez-Rodríguez

Mining is generally considered a large-scale hightech industry. However, it has estimated that about 12 million people, about 30% of the world’s total mining workforce, relied on small-scale mining for their livelihoods. During the years, the large-scale mining industry has developed best practice environmental procedures, which have been applied in diverse settings through the world. In contrast, small-scale mining is better known for its high environmental impact and the lack of safe and healthy working conditions. This paper will discuss the environmental control strategies used by the large-scale mining industry, and its applicability to small-scale mining in developing countries.

Jan 1, 2005

By Nigel Fung, J. D. Humphrey, R. H. Oats, J. H. Ingle

Production dozing of cast material is a cost effective method of improving dragline or mobile equipment overburden removal. Yet dozer productivity is reduced during the part of the process that requires the dozers to cut material away from the highwall. One solution is to use a hydraulic excavator to remove this material and throw it into a windrow for the dozers. By freeing up the dozers for more productive work the overall system productivity increases 25% and cost per yard is reduced by up to 10%. Dozer fleet sizing can be determined to match a specific production schedule or can be sized to balance with an excavator’s production.

Jan 1, 2004

By P. Somasundaran

The use of chemical additives in ultrafine grinding will be reviewed in this paper for the case of grinding of quartz in solutions of surfactants and inorganic electrolytes including some dispersants under different conditions of pH and ionic strength Mechanisms are examined by correlating the grinding effects with those obtained for the influence of these chemicals on zeta potential, pulp fluidity and flocculation/dispersion characteristics The analysis suggests grinding depends mainly on the state of aggregation of the ground products inside the mill and pulp fluidity Implications of the observed effects on ultrafine grinding in general are discussed

Jan 1, 1983

By M. M. Ragin, B. J. Scheiner

The US Bureau of Mines (USBM) has been investigating the use of polyethylene oxide (PEO) as a flocculant for a variety of mineral wastes. As part of this investigation, the hydrodynamics of the flocculation process were studied. It was determined that to obtain optimum dewatering results, the factors of energy input into the stirrer, polymer concentration, and polymer dosage must be considered. It was found that at a given polymer concentration, there were an optimum stirrer speed and polymer dosage. With excess PEO, the amount of water removed in the trommel decreased, but no evidence for steric stabilization was observed.

Jan 1, 1987

By David L. Moffatt, Leon Peters

A unique electromagnetic pulse sounding system for the detection and identification of geological and man-made anomalies which represent hazards in hard rock rapid tunneling operations is described. The main features of the system including a periodic video-type pulse interrogating signal and a probe structure that permits operational modes which either "see" or are "blind" to homogeneous-type targets are reviewed. The results of experimental pulse measurements on targets buried in the overburden and in a limestone medium are presented. Since the electrical properties of limestone are not radically different from those of a hard rock medium, conclusions based on these data should be valid for a hard rock media also.

Jan 1, 1997

By Albert W. Evans

Introduction Engineering Health and Safety is concerned with the understanding of the complex interplay between the risk of injury with technological ,environmental, individual, organisational and legal factors. With this understanding, the design and decision making processes can be balanced with the other objectives of industry and employment to arrive at solutions which place appropriate controls on technology and other aspects of human activities to prevent disease and injury to personnel in the coal mining industry and the design of safe production machinery and ancillary equipment. Advances in the detection and diagnosis of causes of diseases and the need for engineering health and safety in the coal mining industry has increased the need for appropriate education and training. Hazards arise in many forms; exposure to toxic chemicals, escape of radio - active materials, explosion of pressure vessels, contact with moving machinery, exposure to dust, environmental dangers such as excessive noise, high temperatures and manual handling etc. As technology advances, these dangers become more complex and less clearly defined and less easily perceived. Consequently, the ways of controlling the dangers also become more complex and wide ranging. The need to educate and train people in coal mining applications of engineering health and safety has been enhanced over the last five years and courses should be established to fulfil the need for competent people to deal with the problems which modern coal mining technology creates together with the legislation that governs engineering health and safety and to carry out research and development work in the coal mining industry. Industrial Involvement The engineering health and safety experts must be prepared to take a more active part in monitoring conditions that exist in the mining industry, and not design from information obtained from the mechanical, electrical and hydraulic expertise and off-the-shelf components from other industries. Surveying and control of the operating environment must be essentially the concern of the engineering health and safety experts and, whilst it is not possible to create a perfect environment for each machine, every effort must be made to minimise failures and hence plan for designs which will maximise

Jan 1, 1986

By Leonard Harris, Rosa H. Harris

An important part of doing business today in the mining industry, especially overseas, involves community assistance programs for the people who live around the mining areas. The purpose of such a program is to build mutual cooperation and respect that will allow the company and its neighbors to live and work in peace. To do this, it is necessary to form associations or foundations and work in a joint venture fashion. The authors discuss in some detail the outline for setting up such programs and the important role that women, in particular, can play in them.

Jan 1, 2001

By P. G. Semple, K. W. Major, R. M. Nendick

As free milling oxide gold ore reserves are depleted, more mining companies are having to evaluate the available alternatives for treating refractory deposits. The selection of a treatment process can be very difficult; and, despite the claims of their respective proponents, there is no one process that will continuously prove superior. Selection of the optimum process for an individual deposit is contingent on the size of the deposit, the grade of the deposit and the refractory nature of the ore. Since extensive metallurgical test programs are usually required to determine the optimum extraction process, an inappropriate initial selection may prove costly and time consuming. This paper discusses the steps involved in evaluating a refractory ore in order to expedite the evaluation of the required process through the feasibility study stage.

Jan 1, 1990