Search Documents

By Walter J. Johnson, Robert L. Chufo

A unique non-contracting coal thickness measurement technique has been developed to measure both the dielectric constant and thickness of a coal seam as part of a sensor array supporting an autonomous coal mining machine. The sensor measures the reflection of an electromagnetic signal from the coal/shale interface. Underground measurements of coal 6- in thick with a dielectric constant of 4 have been confirmed. Measurements were also made of a 31-in thick coal pillar for application of the sensor to highwall mining. The electromagnetic measurement technique, the data reduction process and field test experience will be presented.

Jan 1, 1992

By Greg Barfoot, Kurt Keskimaki

The Henderson Mine is located approximately 50 miles west of Denver, Colorado. A project is underway to replace the existing rail system which transports molybdenum ore 15 miles from the mine to the mill using three flight conveyor system. The first conveyor is a 1 mile, high lift conveyor which transports the ore from an underground crushing station to the end of the existing rail tunnel. The second conveyor is 10 miles in length and utilizes the existing rail tunnel to transport the ore from the mine, which is on the east side of the Continental Divide, to the mill located on the west side. The third conveyor takes ore from the tunnel portal to the mill through a series of 7 horizontal curves and inclines up to 15 degrees. The project applies advanced conveyor design to tackle the installation of the system in an operating mine and achieve the highest possible level of reliability. This paper outlines the design process for this system, discusses the options which were evaluated and how the current design evolved.

Jan 1, 1998

By K. S. E. Forssberg, M. I. Hallin

In many cases, the reuse of process water in flotation plants is desirable both for plant operating reasons and for environmental protection. The main advantages are better housekeeping of fresh water and process chemicals together with the reduction of polluting species to the environment. There are however a number of problems involved in the use of recycled process water. The main problem is that recycling sometimes has a deterious effect on the process and can occur months after the start of water recycling. The Division of Mineral Processing of Luleå University of Technology has been conducting experiments on recycling of process water at various sulphide plants in Sweden for over ten years. The experiments have been carried out in pilot- and full industial scale, in collaboration with the mining companies operating the plants. Until 1988 investigations were carried out in four different sulphide plants. The objectives of the experiments were: first to document differences in the composition of the process water during recycling; secondly to investigate any changes in the pulp chemistry of the flotation circuits wich may be due to the influence of recycled water; and lastly to establish critical levels, if any. of the parameters measured. While conducting experiments of this kind several things have to be kept in mind. Normally, recycling is done by using tailings pond water as process water. This means that time effects are important, because of the time lag between water input in the tailings pond and the reclaim of that water back to the plant. As will be shown, the

Jan 1, 1989

By R. Woods, O. A. Kiehn, C. A. Born, F. N. Bender

Development of the flotation reagent scheme at Climax Molybdenum Company's mine at Climax Colorado is reviewed. Features of the mineralogy, milling practice and background of reagent changes are outlined. Special attention is given to the hitherto unpublished details of the application of depressants for copper and lead impurities. The present rougher flotation reagent scheme utilizes a neutral hydrocarbon oil, low in unsaturates and wax, as collector with a sulfated coconut oil emulsifier and pine oil frother. Lime and sodium silicate are used as rougher conditioning and slime dispersant agents. Chalcopyrite and galena impurities are de- pressed in both rougher and cleaner plants by stage addition of Nokes reagent and sodium cyanide to yield a metallurgical grade molybdenite concentrate containing greater than 90% molybdenite and less than 0.5%, 0.1% and 0.05% iron, copper and lead impurities, respectively.

Jan 1, 1976

By D. A. Rice, R. G. Swanton, A. May, O. C. Carter

As part of a cooperative effort between the US Bureau of Mines and the Florida Institute of Phosphate Research (FIPR), with input from the phosphate industry, the conversion of phosphogypsum to sulfur is being investigated. The proposed process incorporates a thermal reduction of phosphogypsum to calcium sulfide (CaS) and a hydrometallurgical treatment to convert calcium sulfide to ammonium bisulfide (NH4SH), which is then oxidized using a catalyst to produce elemental sulfur. The paper summarizes the results of continuing laboratory studies using an activated carbon catalyst which was loaded with sulfur through oxidation of ammonium bisulfide solution. The extraction of the sulfur that forms in situ on the catalyst is a key area in the development of the sulfur recovery process. Two approaches for removing the sulfur are being investigated: (1) thermal treatment to volatilize sulfur. and (2) leaching the sulfur using liquid anhydrous ammonia. The research has shown that it is technically feasible to recover over 90% of the sulfur from the carbon by either volatilization or ammonia leaching. Locked cycle testing has demonstrated that the carbon has the potential to be recycled after ammonia leaching.

Jan 1, 1987

By S. K. Kawatra, T. C. Eisele

Microorganisms, such as the bacteria Thiobacillus ferrooxidans, have been reported to depress pyrite flotation (Elzeky and Attia, 1987; Atkins, 1990). However, the depen¬dence of the depression on the type of organism or on suspension pH is still being determined. In this study, the relative effectiveness of various microorganisms (chemolithotrophic bacteria, chemoorganotrophic bacteria and yeast) over the pH range of 2 to 12 was studied. Screen¬ing tests using microflotation showed that every microorgan¬ism tested was capable of depressing naturally hydrophobic pyrite at acidic pH. Larger-scale experiments with both mineral pyrite and coal pyrite using Thiobacillus ferrooxidans and Saccharomyces cerevisiae as depressants, showed that these microorganisms are very effective depressants for mineral pyrite at acid pH, but they are largely ineffective at neutral and alkaline pH, where the mineral pyrite surface is not naturally hydrophobic. The flotation response of the coal pyrite was completely different from the mineral pyrite. The coal pyrite was most floatable near neutral pH, with the floatability decreasing in acidic or alkaline solutions. De¬pression of the coal pyrite by yeast was not selective between the pyrite and the associated coal under the experimental conditions.

Jan 1, 2000

By William Moser, B. P. Shagula

INTRODUCTION Every day mine management and mining personnel face the threat of a possible mine disaster or fire. Their ability to deal with such a situation safely and effectively depends on the level of emergency preparation developed and maintained. After conducting numerous informal evaluations or audits at different mine sites throughout West Virginia (as well as other states), the authors concluded that many mining operations are not prepared to handle a fire situation. The results of the audits indicate that while most mines are in compliance with federal and state legal regulations regarding levels of emergency equipment, water systems and training sessions, these levels - particularly in the area of fire training - are probably not sufficient to enable the mine employees to effectively combat a fire in its early stage. This paper will present the authors' recommendations for designing and maintaining an efficient mine emergency preparedness Program and an overview of the curriculum of the mine fire training Program currently being conducted. MINE EMERGENCY FXEPAREDNESS PROGRAM The Mine Emergency Preparedness Pro- gram (MEPP) is a management tool developed by the Mining Extension Service at West Virginia University and was designed to assist company personnel in effectively managing a mine emergency operation. The program goes beyond the traditional and required training of mine rescue teams by offering a complete emergency operations package. Included in MEPP are suggested approaches for training and organizing all personnel, ideas for developing plans of action concerning transportation, security and communications. The MEPP program may also be used as to assess present readiness levels. While the MEPP program is designed to address all types of emergency operations, the authors are convinced that emergencies involving mine fires are the ones of greatest concern and so are concentrating their efforts in that direction. Incidents where fires are involved seem to be increasing in frequency and are extremely costly to control if allowed to go beyond the incipient stages. With a proper emergency preparedness program in place and properly trained and equipped fire brigades, the authors feel that it is possible

Jan 1, 1992

By E. L. Smyth, A. Button

The apparent absence of significant Tertiary auriferous palaeoplacers in the Yilgarn Block of Western Australia can be explained by the dissolution of the placer gold into the highly saline, acid, oxidising ground waters which currently occur in upper portions of the palaeochannels proximal to the gold sources. The dissolved gold has then been redeposited in redox fronts further downstream. The placer gold is preserved in more distal portions where the ground waters are reducing. Exploration for these placers can be effective using the gravity contrasts that exist between the Tertiary sediments and the Archaean bedrock and SIROTEM which can detect the highest salinity zones which occur in the deepest parts of the channels. Final assessment of the gold content of the sediments must be determined by drilling.

Jan 1, 1989

By B. Denby

Recent advances in virtual reality (VR) have resulted in major opportunities for improving the safety training of mine workers, supervisors and managers. VR has the potential to expose mine personnel to hazardous situations in a safe, highly visual and interactive manner. Customized simulations of mine layouts, dynamic operations and mine environment can be set up, and mine personnel can be allowed to move around the virtual mine, making decisions at key points. The consequences of both correct and incorrect decisions can be immediately fed back to the trainee.

Jan 1, 2000

By Thomas G. Hayes

Track-type tractors remain one of the most cost-efficient stripping tools available to coal miners. Whether they are "sweetening up" a dragline operation with prebenching or serving as the primary tool, dozers are important in driving down mining costs. This article reviews the application zone of track-type dozers. It also provides suggestions for site setup, equipping tractors and machine operation. In recent years, the track-type tractor has become more of a production tool in mining. With the advent of bigger machines, bulldozers have become a typical component in mining operations, removing overburden down to the top seam of coal. Large tractors can also be teamed up with draglines and other systems to maximize the effectiveness of the mining system. Bulldozers remain the tool of choice for topsoil removal, spoil reclamation or any application that demands low ground pressure, or short distance. The introduction of the 523-kW (700-hp) track-type tractor to the mining industry has made the bulldozer a low-cost-per-ton means of removing overburden. The large tractors offer enough productive capability to be considered prime stripping tools. And they can lower mining costs by complementing other mining systems (dragline, cast blasting and loader/truck). Four criteria determine whether a track-type tractor is the right machine for a particular application: ? Production requirements - dozer may fit job requirements better than a second dragline. [ ] ? Product support - availability of parts, service and technical expertise. ? Labor situation - how much of the cost per ton goes to the operator. ? Resale opportunity - recover a percentage of capital cost. Mining efficiency is economically controlling the cost of any system. Most operations rate the most economical means of moving material as cast blasting, dragline and the track-type tractor. All three of these systems share one common value: They are all sensitive to distance. Regardless of the application, all mining systems have an economic range. Exceeding this distance will affect cost and productivity.

Jan 1, 1997

By Nicholas T. Camicia

A career in the coal mining industry today offers students one of the most interesting and challenging opportunities available in the industrialized world. As reserves of other fossil fuels dwindle in face of the world's demand for energy, it has become apparent that coal, once the king of energy sources, must be relied upon again as the major fuel for powering industrial growth in developed and developing nations. Centuries of coal supplies lie beneath the earth's surface, assuring the world of a steady, plentiful supply of energy until science and technology can produce a way to harness and efficiently use renewable sources, such as solar. The need to increase our use of coal during the last two decades of the 20th century is reason enough to believe that the future growth of the coal industry is assured. A major impediment to that growth might be backward national public policies that could restrict the full utilization of our coal reserves. These policies could result from overregulation and a failure of the public to recognize that coal use, with proper techno- logical safeguards, is compatible with our society's environmental-quality objectives. Communication of this problem and its solution is a major undertaking of the coal industry in the 1980s. At the end of the 1970s, the American coal industry was producing approximately 635 Mt/a (700 million stpy) of coal. To meet the nation's projected energy needs by 1985, the annual tonnage must be doubled. A similar scenario is predicted for the rest of the world. Such growth in the modern international business world will require huge additional amounts of capital, equipment, and people who know how to wisely raise and apply the capital ; use the equipment productively; and deal with the many community, public, and governmental problems such expansion will create. Whether a student's interest is in actual mining operations, business administration, engineering, finance, law, industrial relations, marketing and sales, or public affairs, a career opportunity is available in the industry.

Jan 1, 1981

By J. P. Golightly

The nickeliferous laterites of Soroako are described in their setting in the huge Cretaceous ultramafic complexes of central Sulawesi, Indonesia. The ore bodies occur on spurs, ridges and hill flanks beneath remnants of extensive erosional surfaces. Weathering pro- files that have developed on unserpentinized harzburgite and on strongly serpentinized lherzolites show distinctive laterite structures, mineralogy and chemistry. The former are unique to the Soroako area and permit an unusual degree of upgrading by rejection of unserpentinized peridotite boulders. A mass balance calculated for a selection of profiles indicates that in situ leaching of a column of peridotite 20-50 meters thick has taken place with only minor lateral migration of nickel in solution.

Jan 1, 1979

By G. D. Hood, B. E. Davis

A problem that has continued to plague the Florida phosphate industry is loss of coarse phosphate in the flotation circuit. Attempts to remedy this problem such as floating the coarse material (plus 425 µm) in a separate circuit have resulted in limited success, but recovery is still not optimum. A fundamental examination of the mechanisms involved in the conditioning of the coarse phosphate has led to results that seem to supersede common paradigms. The Bureau of Mines investigated conditioning parameters such as fatty acid/fuel oil dosage, residual clay content in the feed, conditioning time, mixing intensity, and conditioner solids content. The study revealed that the effect of all these parameters was important. However, it was discovered that contrary to common beliefs, the conditioning time affected the grade of the rougher concentrate much more than the recovery. Specifically, the longer the conditioning time, the less quartz that was floated. It was also discovered that high mixing intensity conditioners could lower the conditioning time required for good grade. Many phosphate operators use low intensity drum type conditioners. Optimizing the conditioning time, mixing intensity, and other conditioning parameters resulted in a rougher concentrate grading 30 pct P.2O5, with an attendant recovery of 95 pct.

Jan 1, 1993

By Robert J. Timko, R. Lincoln Derick

The Bureau of Mines evaluated the integrity of escapeways in a three entry underground coal mine. A center conveyor belt entry (secondary escapeway), was flanked by an intake (primary escapeway) and a return entry. Diesel equipment was used throughout the mine for material and personnel haulage. A carbon monoxide monitoring system, tied to a data recording computer on the surface, was deployed throughout the belt entry and at selected sites in the intake and return entries. Previously, the company had a fire of unknown origin in another mine, which prompted an interest in the performance of their escapeways. An initial, qua1itative evaluation was performed by burning approximately 14 kg of coal at the mouth of the intake entry. The first test was followed by a similar burn at the mouth of the belt entry. These initial trials showed a high quantity of leakage between entries. In several follow-up evaluations, simulated fires, using a tracer gas, were set in the intake and belt entries. Tracer gas concentrations were obtained in all entries at four different underground locations. The results of these tests showed that permanent stoppings could not guarantee isolated, contaminant-free escapeways.

Jan 1, 1989

By Roger G. Haga, Richard P. Campbell

Introduction Project scheduling . . . . • What is it? • Why is it done? • Who does it? • How is it done? • When is it done? These are some of the questions that will be addressed in this paper. It is intended that by exploring these questions, an understanding of project scheduling, its purpose and benefits can be achieved. The purpose of this article is not to describe in detail "how to schedule", but rather to give an overview of the scheduling function on a project. A successful scheduling effort is dependent upon the people responsible for developing, implementing, and monitoring the schedule, and the tools and procedures that are used. These three elements are integral components of project scheduling. What is it? A schedule is the integration of network relationships, resource constraints and the calendar. The schedule identifies when the activities "will" be done, while the network states when they "must" be done. Networking techniques are the most widely accepted scheduling tool for complex projects. The benefit of the network is the simplicity in illustrating, presenting and analyzing the dependency relationships of a project. The logic network is the foundation of the schedule. When calendar dates are applied to the logic network, it becomes a schedule which provides the basis for evaluation of project status, forecasting the occurrence of events and controlling the project. The sequence of activities that requires the longest time to complete determines the overall duration of the schedule. This longest sequence of activities is called the "critical path". The "critical path method" (CPM) is used to describe this particular schedule network methodology. The two common conventions of CPM networks are the "arrow diagram met hod" (ADM) and the "precedence diagram method" (PIM). There are arguments in favor of each of these two methods, and usually the one that is used is a matter of personal preference, project directive or corporate procedure.

Jan 1, 1986

By Thomas R. Yanske, Jonathan E. Carmack, Lyndon M. Clark

In order to maximize the extraction of high grade pillars at The Doe Run Company, artificial pillars are created using cemented rock fill (CRF). CRF pillars aid extraction of pillars in two ways. One is to offer back support for the immediate area where pillars are being extracted. The second is to increase the post failure residual strength of pillars surrounded by backfill. The CRF is produced using a combination of minus 1.0 m run of mine (ROM) rock and minus 5 cm crushed rock. Depending on the operation the CRF slurry is either produced in an underground or a surface batch plant. The slurry and rock are transported to the fill area by truck where they are mixed and placed in 1 m lifts. To reduce the amount of CRF needed, fill fences are constructed around the perimeter of the CRF pillar. Within these fences ROM CRF is placed in lifts until within 0.6 m of the back after which minus five centimeter CRF is slung tight to the back utilizing slinger trucks. In constructing these artificial pillars a number of set procedures have been established to ensure that the work is done both properly and safely.

Jan 1, 2001

By R. A. Jankowski, R. Gong, R. Bhaskar

The control of respirable coal dust in continuous mining sections involves careful analyses of the generation and transport of the dust, including airflow pattern analyses. Potential dust control devices must be evaluated based on their effect on both local dust transport and potential dust exposure of face personnel. The development of larger and more productive continuous miners increases the need for research on dust control and improvement of visibility in the face area. Two studies relating to underboom dust control are discussed. The first study involved the valuation of potential underboom dust control techniques to reduce operator exposure to dust and determining the relationship between the positioning of exhaust ventilation and the exposure of face personnel as a function of face and operating variables. The study involved full-scale laboratory experiments using a state- of-the-art data acquisition system. The second study related to the use of foam under a continuous miner boom and its effect on silica concentration and respirable dust. The foam study was performed in a coal mine. The laboratory studies involved the fabrication of a full-scale test facility and development of a computer based data acquisition system. This was followed by baseline data collection, smoke trace tests, detailed performance testing of various underboom dust control measures and data analyses. The underground foam test involved the design and installation of the foam generation and delivery system, testing, and data evaluation. The results of the studies are summarized in this paper.

Jan 1, 1991

By David A. Milligan, William Cobb

2.1 INTRODUCTION This chapter provides the reader with a sense of how a heap leach project may make an orderly, and hopefully non-traumatic, transition from discovery or acquisition to project construction. In making this transition a project can pass through several project development phases (i.e. ore definition and delineation, conceptual engineering, detailed engineering, and ultimately on to project construction and operation). "Go" or "no go" decisions may occur at any point in each of these phases. The transition from ore definition to detailed engineering should be accomplished via a well thought out program of interdisciplinary studies and an integrated, interdisciplinary project team. This chapter also describes, in general terms, a "roadmap" approach to the project evaluation process that must occur as project planning and development progress. It is the experience of the authors, as well as a myriad of companies who have been through the heap leach project development process, that a systematic approach will save many headaches, and many dollars. In fact, it is safe to say that a project with no formalized system of "objectives setting" and "milestone charting" may well flounder along the way, even if an economic ore body exists. Many papers and technical articles have been written about various aspects of mineral resource appraisal, economic evaluation, and mine development. Most of these invoke the same general philosophy of a systematic approach to project evaluation and development, although methods cited for attaining goals are quite variable. This is undoubtedly appropriate, given the fact that there is great variation in approach to project development (e.g., climatic considerations, ore body size and physical ore characteristics, permitting constraints, etc.). For the purposes of this chapter, two primary sources of information have been used to highlight the "road map" approach previously alluded to. These sources are cited throughout the text as Mackenzie (1980) and Snow and Michel s (1986). A brief summary of each of these sources is provided below: Brian GJ. Mackenzie of Queens University (Mackenzie, 1980) has developed a wealth of information concerning project development topics. Much of this information is synthesized in his notes for a short course entitled : "Mineral Exploration Planning and Economic

Jan 1, 1988

By G. O. Kesse

The Republic of Ghana, located on the West Coast of Africa, is one of the West African countries rich in bauxite deposits. The main occurrences of bauxite deposits are at Sefwi Bekwai in the Western Region, Aya-Nyinahin in the Ashanti Region, Atewa Range near Kibi and at Mount Ejuanema both in the Eastern Region of Ghana. These bauxite deposits belong to the so-called blanket deposits as they are associated with erosion surfaces of old peneplains and occur as cappings on the flat tops of hills or mountains whose heights are generally greater than 600 metres above sea level. These deposits can also be classified as laterite-silicate bauxites since they have been formed under tropical weathering conditions. Genetic and mineralogical investigations have revealed that all bauxite deposits of Ghana are the result of indirect bauxitization processes, for the minerals of the weathering parent rocks have not been transformed directly into gibbsite. In all cases, lithomarge of kaolinitic clay can be recognised. The geology of the major occurrences of bauxite in Ghana shows that the Mount Ejuanema deposit is the only deposit associated with the Voltaian System of rocks. This rock System consists mainly of sandstone, shale, mudstone, conglomerates and pebbly beds. All the otter deposits are associated with the Birimian System of rocks which are made up of metamorphosed lavas,pyroclastic rocks, hypabyssal basic intrusives, phyllites, schists, tuffs and greywackes.

Jan 1, 1984

By M. J. Laurila

On-line analyzers have made possible the use of fuzzy logic control (FLC) for local control applications in coal preparation plants. This includes FLC of heavy media vessels, cyclones and froth flotation. These circuits can be controlled in real time in a feedback control loop with an on-line analyzer. Control strategies can be developed using statistical process control (SPC) techniques that are first applied offline in manual mode through the use of control charts. This process is then brought on line using FLC in conjunction with an on-line analyzer to automate the circuit. The advent of programmable logic controllers into preparation plants has enabled the implementation of regulatory control. As shown in Fig. 1, regulatory control is the first level of process control as applied in a processing facility. This involves: ? The logic sequences for start-up and shutdown procedures and all the necessary interlocks for safety purposes. ? The systems to control individual parameters and individual units. Various sensors provide information that is useful to plant operators, while some can be used as signals to simple control loops (Couch, 1996). This is the foundation of process control. It must be performed well if there is to be any success in supervisory control (level 2). Supervisory control involves overseeing and directing the operation of unit operations, or of the whole plant. This includes more complex loops with cascade control. And it may involve feed forward and feedback systems. There have been some applications of this kind of control to thickeners and flotation circuits in coal preparation plants. In addition, there are supervisory controls on some dense medium circuits and, in a few cases, on jigs. These are implemented with proportional integral- derivative (PID) controllers that are available in the PLC or distributed control system (DCS) operating soft ware. In a coal preparation plant, there might exist 200 to 400 PID loops. In a coal-pro¬cessing plant, this number is increased to 2,000 loops or more. It is important to use the correct algorithm or function to control a process variable to the point where automatic control shows a markedly decreased variability over manual mode. This is where fuzzy logic and neural networks have an advantage over traditional model-based expert systems. Because dynamic models of coal preparation unit operations do not exist, model-based expert systems that are prevalent in minerals processing cannot work. Not enough is known about the dynamics of the gravity separation processes employed in coal preparation. Therefore, an artificial intelligence (AI) system consisting of a subset of fuzzy logic, genetic algorithms and neural networks must be applied in coal preparation plants if a supervisory control system is to be successful across a range of feed characteristics and variable set points.

Jan 1, 1997