Search Documents

By D. K. Grubbs

Anorthosite is an abundant, domestic source of alumina with reserves in individual deposits ranging from a few billion to hundreds of billions of tons. While anorthosite contains less alumina than does kaolinite, its CaO and Na20 contents are significantly higher (Figure 1). Alumina can be produced from anorthosite by alkaline, soda-lime sinter or acid processes. CaO and Na20 are advantageous because they are reactants consumed in alkaline processes. Acid processes require high calcium plagioclase feldspars (bytownite-anorthite) to obtain high alumina extraction because the lower calcium plagioclase feldspars (andesine-labradorite) are not as readily dissolved during digestion. The layered Raggedy Mountain Gabbro group in the Wichita complex in southwest Oklahoma is a high calcium anorthosite that could be processed by acid, sinter, or alkaline methods. Chemical grade limestone in the Arbuckle Group is located within 45 km of the anorthosite (Figure 2).

Jan 1, 1980

By B. J. Scheiner

A ferrous chloride-oxygen leaching system was investigated by the Federal Bureau of Mines as a means of re-covering copper and silver from a sulfide concentrate that had been pretreated to remove a majority of the antimony. The pretreated concentrate contained Cu, Ag, Pb, Zn, Sb, and As. Parameters affecting metal extraction, such as temperature, pressure, amount of ferrous chloride, and initial hydrogen ion concentration, were studied. Copper extraction of 98 pct was achieved by leaching 4 hours at 40 pounds per?square inch gage (psig) and 1000 ?C. Copper was recovered from leach solutions by cementation with iron, and the resulting ferrous chloride was recycled. Leaching the residue with cyanide followed by electrowinning recovered 99.7 pct of the silver. Iron, Sb, As, Pb, and S reported to the tails.

Jan 1, 1978

By Felicia F. Peng

Two modes of collector addition techniques are applied in the column flotation for cleaning ultra fine coal. The collector can be: 1) added directly into the coal slurry through the feed system; and 2) gasified collector and transported in the gas phase through the bubbles. Operating parameters of the column flotation were investigated through three phases of work plans for Pittsburgh No.8 seam coal. In present study, the column flotation using two modes of collector addition techniques were tested and compared. Ninety percent or higher combustible recovery can be achieved by using both methods. However, utilizing the gasified collector addition technique in column flotation has more potential than direct liquid addition technique to obtain the higher recovery at same collector dosage.

Jan 1, 1993

By Michael C. Newbury

For thousands of years gold has been not only a commodity, valued for its comparative scarceness, immutability and homogeneity but also a medium of exchange which has no nationality. Approximately 90% of the gold produced is still accessible in the world, although some of it in museums, galleries, jewellery and dental work is not immediately available for circulation. The majority is held as bars by central banks for their reserves; the balance circulates as coinage or bullion held for investment. The value is further enhanced by the political aspect that gold cannot be debased as paper currency can and, therefore, it always becomes an investment refuge. It has always been possible to buy and sell gold at a price which is readily established by reference to bullion's weight and purity; and it is this fact which makes a loan denominated in gold, rather than one in currency, a viable alternative means of finance. The purpose of this paper is to discuss some general aspects of what is considered to be one of the more effective and presently popular methods of financing the development of a gold mine - the gold loan. This is not intended to discuss all the minute details which must be uniquely designed to fit each individual situation, but rather to provide general guidelines. You will all be aware of the traditional sequence whereby companies primarily finance exploration work by the raising of equity through the sale of shares to the public or by that unique Canadian form.

Jan 1, 1987

By Steven A. Elmquist

Although past investigations (2, 5)have been conducted to determine crushing relationships, no program which covered a broad range of crushing conditions had been conducted. The previous studies appear to concentrate on small segments of the overall picture and did not fullfill our desired information objectives. The Crusher Variables Research Program conducted at the Mineral Research and Test Center (MRTC) of Rexnord, due to the broad range of variables utilized in a production size crusher, is believed to be the most comprehensive study of its kind as of this date. The principles developed by the Symons brothers in 1925, when they patented the cone crusher as we know it today, are still being used in the machine known as the Symons Cone Crusher, During the development of this novel crushing concept, a technique known as the fall of material (called the Bouncing Ball Theory1 by some) was used to determine an idea as to the proper head angle, eccentric and speed of eccentric rotation, The final variables used for the Symons Cone Crusher design were, therefore, the logical conditions to start with and use as a reference against which other variables could be compared.

Jan 1, 1979

By J. Keng, S. T. Chen, T. M. Shih

Kwanyin Tunnel is presently the longest (7.7 km) railway tunnel in Taiwan. Due to heavy railway traffic, a pass-by station will be built inside the tunnel to increase the traffic flow. Since the concentration of toxic gases released by the locomotives may reach dangerous levels, a research program was conducted for the purpose of designing a ventilation system which could dilute and/or remove the toxic gases to maintain an acceptable pollutant level. The program consisted of two parts. The first part was field measurement during which the concentrations of pollutants and wind velocities were measured at various points inside the tunnel to acquire basic data regarding ambient air quality, piston effects for the different types of trains, and existing ventilation conditions. Weather data (temperature, humidity, atmospheric pressure, wind direction and velocity) were gathered at many stations, both on the surface and inside the tunnel. The amount of pollutants released by each type of locomotive for various conditions were also measured. The second part of this study involved establishing mathematical models for predicting the air quality of the various proposed ventilation systems. Three different models were used for this work. The first one is a piston effect model which assumes that the gases and air undergo immediate mixing inside the tunnel. The second one is also a piston effect model which assumes that the diffusion ability of the gases is zero. The third one is a conventional ventilation model which was used for natural and mechanical ventilation conditions. From the result of field measurement and mathematical model studies, a ventilation system was chosen with consideration of both ventilation effects and construction costs.

Jan 1, 1987

By C. Cigna, M. Patrucco, D. Savoca, E. Lovera

The paper deals with the activity program and the preliminary results of a research work commissioned by IReR Research Centre and Regione Lombardia to the Department of Land, Environment and Geotechnologies of Politecnico di Torino. The aim is to define measurement, analysis and control criteria for the emission of chemical and physical pollutants from non-metal mining industries, with particular reference to noise and airborne particulates. Such emissions are related to health risks and annoyance problems, both for the working crews and the neighbouring population, and so, in order to get an effective sustainability of the industry, suitable reduction methods and assessment tools are required. A simple technique for the evaluation and forecasting of both the emission levels and deriving impact has been tested at different mining and quarrying sites, considering their differences in terms of layout and exploitation method, the latter ascribed to a series of main typologies as present in Lombardia region.

Jan 1, 2005

By L. E. Allen, J. F. Abel, D. R. Morgan

The Waste Isolation Pilot Plant (WIPP) is a geologic repository for disposal of transuranic waste and is operated by the U.S. Department of Energy (DOE). The repository is located at a depth of 655 m in the Permian age salt beds of the Salado Formation, 40 km east of Carlsbad, NM. A key component in the design of the WIPP repository is the installation of concrete structures as panel seals in the intake and exhaust drifts after a panel has been filled with waste containers. The DOE has proposed several panel closure design modifications to the EPA. EPA approval of the changes is required since the details of the designs are specified in EPA’s final rule as a condition for WIPP certification. The Environmental Evaluation Group, in its role of providing technical oversight on the WIPP project, has evaluated the proposed modifications. An analysis of this evaluation is discussed.

Jan 1, 2003

By P. C. Kapur

The hierarchical relationship between three broad kinds of grinding models for a spatially homogeneous, linear, time-invariant batch grinding system are first established. Limiting and asymptotic arguments for arriving at approximate but simpler models are employed in all three cases. These parsimonious models -provide alternate and, in some respects, more incisive and convenient tools for the analyses of grinding processes and simulation of comminution circuits. In the discrete-size, discrete- time class of models, a reduced mill matrix is derived, which is seemingly adequate for those grinding circuits whose identification otherwise is difficult because of limitations on the quantity of data and its quality. In discrete-size, continuous-time types of models, parameter lumping has been employed for obtaining a G-H solution which is quite accurate and exceptionally useful for graphical display of data, model verification, and parameter estimation and simulation. In continuous-size, continuous-time models, a similarity transformation is used for solving the integrodifferential equation of grinding. This solution provides a unified framework for a number of apparently diverse empirical grinding phenomena such as self-preserving behavior of ground particle size distributions and energy laws.

Jan 1, 1987

By I. K. Kapageridis

Digital photography combined with three dimensional models of topography, mining operations and restoration plans can lead to extremely realistic images and animations of the current and future states of a mine or quarry. The amount of work and the time required for the successful modeling of a mine and its restoration plan are surprisingly low nowadays. All this means that the visual impact of mining and quarrying operations can be easily assessed using common computer hardware and some dedicated software packages. LAVA Mining and Quarrying SA is a company committed to strive continuously for the highest possible environment protection at the company?s quarries. The pozzolanic rock quarry located at Xylokeratia is one of the company?s quarries on the island of Milos and the subject of the study presented in this paper. A thorough restoration plan of the Xylokeratia quarry is being completed by the company. For its purposes, a complete visual impact assessment study was performed at the Department of Geotechnology and Environmental Engineering of the Technological Education Institute of Western Macedonia. The procedures used in this study and the produced visual results are presented in this paper.

Jan 1, 2006

By L. R. Moore

The World Health Organization (WHO) considers contamination from oxyanions, such as selenium and arsenic, a global concern. While their elemental forms are toxic, the aqueous oxyanions are more so. These aqueous forms, which exist at a higher oxidation state, are the most common forms released during mining processes. Many technologies are capable of meeting the governmental discharge criteria for oxyanionic contaminants, but may possess limitations due to redox chemistry as well as the water matrices. An innovative technology was developed that can successfully reduce such aqueous forms generated during mining processes to a level below the discharge criteria. This paper discusses how an understanding of the sensitivities of this novel adsorbent towards these variations in water matrices and redox chemistry can be used to optimize its application.

Feb 27, 2013

By Raja V. Ramani, Wilson Miola

The potential health effects of quartz-bearing airborne dust in mine and mill atmospheres point to the need for the quantification of quartz content in the source material for determining the source-sink relationships and for choosing applicable control measures. While a standard method exists from a regulatory point of view for the sampling of coal mine atmospheres for determining (i) respirable dust concentrations and (i) the amount of quartz in thesamples, there is no generally accepted standard method for quartz analysis in bulk samples of coal and host rocks. Generally, the bulk sample is reduced to a powder for producing quartz analysis samples. Extensive controls are necessary to ensure representativeness of the analysis samples when these are very minute fractions of the bulk samples. Since the amount of analysis sample is not limited, alternative methods for quartz analysis may also be tried. It is, however, necessary to adopt a procedure which will satisfy several statistical requirements to guarantee representativeness of the quartz analysis samples. In this paper, the important factors in the preparation of quartz analysis samples from the host rocks and bulk samples are discussed. The method developed to prepare the analysis samples is outlined. The results of application of the procedures are presented. The procedure developed for quartz analysis sample preparation is based on sound statistical foundations. The procedure has been validated for reproducibility and homogeneity.

Jan 1, 1991

By J. Richard Kyle

Salt domes, their cap rocks, and the adjacent sedimentary strata represent a major economic resource in the Gulf of Mexico basin. Gulf Coast salt diapirs formed in response to sediment loading of the "mother" Louann evaporite sequence of middle Jurassic age, an effect that is caused by the buoyant nature of the lower density salt. Halokinesis progresses from nonpenetrative deformation that creates broad "pillow" structures into discrete high-amplitude diapirs. Because of its buoyancy, the top of the salt diapir remains near the land surface or the seafloor during much of its history as the basin floor subsides. The salt within the Gulf Coast diapirs is deformed complexly and commonly shows subvertical banding that represents modified sedimentary layers with different contents of nonhalite components. The most abundant impurity is anhydrite, which occurs as individual millimeter-scale crystals or as deformed clasts that generally form about 5% of most salt stocks. Many mature salt diapirs are mantled by a "cap rock" that consists of a lower anhydrite zone and an upper calcite zone, commonly separated by a discontinuous gypsum-bearing zone. The anhydrite zone forms as accreted layers of anhydrite grains and clasts that are left after episodes of halite dissolution. The calcite zone is a product related to petroleum destruction accompanying bacterial reduction of aqueous sulfate. Calcite-cemented siliciclastic strata occur above or alongside diapirs. The mineral resources of the salt-dome setting are remarkably diverse. Major economic products of the salt-dome environment are salt and cap-rock-hosted native-sulfur deposits, as well as petroleum resources that occur on the dome flanks and in the cap rock. Native sulfur forms as a result of bacterial sulfate reduction accompanying petroleum destruction to form hydrogen sulfide, which is subsequently oxidized to elemental sulfur, major amounts of which have been produced by the Frasch process from Gulf Coast salt-dome cap rocks. Some cap rocks have produced limestone, gypsum, and anhydrite for a variety of construction uses. Although traditional industrial-mineral resource production from Gulf Coast salt domes is shrinking, some cap rocks host potentially commercial concentrations of celestite and barite, as well as the metals Zn, Pb, and Ag. Furthermore, caverns, excavated within the salt stocks, serve as major storage facilities for crude oil (including the Strategic Petroleum Reserve), liquefied petroleum gas, and natural gas. These resources are products of fundamental geologic processes that are integral to the evolution of the Gulf of Mexico basin. Whereas production of some industrial-mineral resources, such as elemental sulfur, has declined in recent years, ample reserves of salt will allow production to continue into the foreseeable future. Further, there is potential for other mineral-resource production from cap rocks under favorable economic circumstances. Expanded use of caverns, excavated in the salt masses for material storage and disposal, is likely to continue into the next century.

Jan 1, 1999

By William C. Grady

The environmental and economic problem created by pyrite in coal are well documented. The removal of pyritic sulfur prior to, or during, utilization has been the object of considerable research, however, much of this research has proceeded without a proper knowledge of the microscopic occurrences of pyrite in coal. This paper investigates the forms, occurrences, and variations in the distribution of pyrite in major West Virginia coal scan. Twenty-nine samples from twenty-two major west Virginia coal scans were selected for this study (see Table I). The samples were selected so as to be representative of the major coal producing areas of the state. All samples, except five, were collected at active surface mines, as indicated in Table I, and all except one were channel samples. The time interval between sampling and preparation of polished microblocks varied from two months to two years, though most were prepared within three months of collection. Grinding, screen¬ing, and riffling of samples to obtain 250 grams of -20 mesh coal for microscopic analysis strictly followed ASTM procedure D2013-72.

Jan 1, 1976

By R. C. Bunge

The selective flotation of semi-soluble salts with fatty acids is often negatively affected by the interaction of the potential determining cation with the ionic surfactant in bulk solution. This problem can be avoided by floating at low pH which involves the emulsification of the collector. The research presented here focuses on the influence of the Ca2+ ion on the flotation of fluorite with palmitic acid at low pH. Our results show that the surfaces of collector emulsions are dominated by precipitation phenomena similar to those encountered in bulk. In turn, fluorite in palmitic solution at intermediate pH displays surface properties similar to those of the collector by itself. This may be due to two alternative mechanisms (i) adsorption of bulk precipitate on the fluorite surface or (ii) the formation of a bilayer of surfactant ions on fluorite. Possibly, both mechanisms occur simultaneously.

Jan 1, 1993

By John T. Awald

The Bradshaw Mountains of west-central Arizona cover an area of 1600 square miles and contain numerous old mines and prospects. The area has been geochemically sampled on a reconnaissance basis to relate mineralized areas to regional structure and rock types. Copper analyses of stream sediments have been classified and contoured to show the distribution of low background, high background, and low, intermediate and highly anomalous areas. Contoured results are compared to geology and known mines. Several prospecting areas are indicated.

Jan 1, 1970

By Joel K. Waterland

GENERAL DESCRIPTION Open cut-and-fill stoping for many years was prob¬ably the most widely used mining method in under¬ground metal mines. Then for a time this method was largely supplanted by the blasthole stope. It again be¬came popular as many mines reached depths or grades where methods requiring large open voids to remain open for extended periods of time became unsuccessful, often as a result of excessive dilution. The open cut-and-fill method is very flexible and is readily adaptable to almost any ore body. The standard application requires that a slice of ore usually 2.4 to 3 m (8 to 10 ft) thick be removed from the back of the stope, and as the ore is taken down, the back is dressed and rockbolted. After the back is secured, the broken rock is removed through rock passes to the level below. When the rock has been removed, the rock passes are extended upward the height of the ore removed, the stope is backfilled, and another cycle is mined. This method is best employed in plunging ore bod¬ies with considerable vertical extent, ore areas that re¬quire selective mining, ore areas where weak wall con¬ditions exist, and ore bodies that have an ore value that will carry this relatively expensive mining method. Blast¬hole stoping, shrinkage stoping, and other mining meth¬ods that do not employ rock passes in a stope are not efficient in plunging or flatly dipping ore bodies because the footwall makes ore removal quite difficult. Since mining is accomplished by taking down slices of the back, only small areas of the wall rock are exposed at any one time, and these only for short periods. Due to limited back height, areas of uneconomic rock may be left in place, or they may be mined and the material gobbed in the stope. Because the miners in the stope must work under freshly blasted areas, the amount of ground control is usually great. The volume of rock that is broken during one section of mining is relatively small and the amount of nonproductive work required is high. This results in limited productivity for the scope and, be¬cause of the nonproductive work that must be done on a regular basis, the production from the stope may be quite cyclical. SUITABLE ORE BODIES The open cut-and-fill method may be adapted to al¬most any type of ore body with a relatively high vertical extent. The ore body must be accessible at both top and bottom as well as at regular intervals throughout its vertical extent. Although adaptable to most ore bodies, the method is probably best employed where the ore has poor con¬tinuity and where most types of bulk mining would pro¬duce excessive dilution. In areas of poor ore continuity, the capability of continuous and extensive sampling dur¬ing the mining of each cycle makes this method very desirable. This capability also minimizes the amount of evaluation sampling that must be done before mining is started. Because of the extractive system used, the size and shape of the stope may be as readily changed as the sampling mandates. Probably the only ore characteristic demanded is that the ore has strength enough to be sup¬ported through the use of rockbolts or cable bolts dur¬ing the mining and backfilling cycles. Good planning, systematic sampling, and careful supervision will pro¬duce a product with less dilution than any other open stoping method. PLANNING Evaluation Planning Once it has been decided that the open cut-and-fill method would be the most efficient for mining a par¬ticular ore body, the next considerations would probably be the availability of an economical backfill material and the selection of an efficient transport system for this material. Although hydraulically transported mill tail¬ings are the most widely used product, this is not always practical due to mill location or the quality of the tailings. In such cases, backfilling may be used. The type of backfill and the type of equipment used will determine if a floor or capping on the backfill is required to minimize dilution during ore removal. The early selection of rock removal equipment is im¬portant since equipment usually determines the amount of development work required to bring a stope into pro¬duction and the size of the openings needed. The size and continuity of the ore body will usually determine the type of loading equipment. The use of slushers or load¬haul-dump (LHD) equipment captive in the stopes will minimize the amount of development. If the ore con¬tinuity is such that a ramp system for extraction can be used, the cost of development will be increased but the flexibility of continuous mining will minimize the cycli¬cal nature of the production. The height of the mining section usually is deter¬mined by the strength of the wall rock and the amount of back bolting required. Once this has been decided, the appropriate drilling equipment can be chosen. The number and sizes of the rock passes employed depends upon the type and size of the extractive equipment and the type of backfill that is to be used. Since the miners must enter and leave the stope each shift, the level inter¬val is usually maintained at approximately 45 m (150 ft). Access from the level above into the stope must be main¬tained at all times. The employees perform all the work in the stope and adequate ventilation must be provided. Stope Planning Due to the flexibility of the method and the vari¬ability of the ore zones, layout is usually done on a stope basis. In areas where continuity is a problem, the size of the stope is usually determined by the boundary of the ore (with all of the ore within that boundary being removed). In areas of good continuity where ramps are to be used, the length of the stope may be determined by the length of time each of the cycles (preparation, back¬fill, mining, and ore extraction) requires. The ramp work is then laid out so that access to the various parts

Jan 1, 1982

By H. Beecher (Original by) Charmbury

Water is a most remarkable substance, essential for life of all kinds. As well as needing water to survive, man has always used it for agriculture, transportation, recreation, and many other things. When our country was young and inhabited by few people, the streams, rivers, and lakes were able to provide all the clean water needed by man and take away all the wastes created. However, with our growing population and an ever-increasing demand for goods and services, the public, industry, and government at all levels have become acutely aware of the need to manage the nation's water resources more efficiently. Abundant energy from many sources has helped this nation to become the greatest industrial nation in the world. Coal has contributed a major portion of this energy, generating electricity, running railroads, and maintaining national security during wartime. The result has been the highest standard of living in the world and a time of widespread economic prosperity. The use of water in coal mining is somewhat different from its use in most industries. With the exception of water used in cleaning plants, for underground dust control, and for fire protection, most of the water en- countered in coal mining operations serves no useful purpose. In other words, it is an undesirable element and must be removed, otherwise it will interfere with operations, cause potential water quality problems, and may even stop operations by flooding. In the past, removing water from working areas of most mines was usually a fairly simple matter. Pumps with piping were installed at sumps or low spots in the mine and the water was pumped to the surface or to drainage control facilities constructed for the operation. Ditches were often used to collect and drain the water by gravity to the outside or to main sumps for pump discharge. In either case, the water was allowed to flow into the nearest stream or river. The concept of "water is water' was generally accepted without too much concern for what was in the water since low-cost products and services, rather than clean water, were the public demand.

Jan 1, 1981

By O. D. Christensen

The Carlin Trend is a 60 km (38 mi) long northwest alignment of epithermal, sediment-hosted, disseminated gold deposits. Collectively, these orebodies contained more than 620 t (20 million troy ounces) of gold. The Carlin deposit, located near the center of the Trend, has become the "type" deposit of this class. There are, however, significant differences between the individual deposits. Six subdistricts can be distinguished, based upon geographic, structural, lithologic, alteration, mineralization style, and geochemical characteristics. They are, from northwest to southeast, the Bootstrap, Bluestar-Goldstrike, Lynn, Maggie Creek, Rain and Bullion (Railroad) subdistricts. Regional Geologic Setting The Carlin District is located centrally within the Great Basin Geologic Province. Host rocks for the deposits include sedimentary units that range in age from Ordovician to Mississippian, as well as a Jurassic-Cretaceous granodiorite stock. During the Early Paleozoic, the area that is now Nevada lay along the western margin of the North American continent. A westward-thickening wedge of sedimentary units was deposited offshore in a eugeoclinal basin; these vary from continental shelf carbonates toward the east to fine-grained siliceous clastic and cherty units to the west. Tectonic activity associated with the Antler Orogeny in Late Devonian to Early Mississippian time resulted in the eugeoclinal Western Assemblage rocks being thrust as much as 140 km (90 mi) eastward over time-equivalent transitional to miogeoclinal Eastern Assemblage rocks along the Roberts Mountains Thrust fault system. The leading edge of the Roberts Mountains Thrust plate formed the emergent Antler highland from which siliceous clastic sediment, eroded from the overriding eugeoclinal rocks, was shed eastward into the adjacent foreland basin. Erosional products derived from the overthrust plate are termed the Overlap Assemblage.

Jan 1, 1987

By Timothy Batchler, Khaled Mohamed, Morgan Sears

The National Institute for Occupational Safety and Health (NIOSH) initiated a testing program to assess the effects of lateral loading on various standing supports used in underground coal mines. This study is not intended to endorse a particular type of standing supports nor to provide a comparison between different types of standing supports. This paper aims to measure the lateral loading capacity of two types of standing supports and evaluate how it affects their vertical loading capacity and yielding mechanisms. The study utilizes the Mine Roof Simulator (MRS) at NIOSH Pittsburgh. Type-1 support is characterized by telescopic tubes made from ASTM A-513 steel with a specified locking mechanism, and Type-2 support comprises a single component constructed from ASTM A500 Welded Grade C pipe. Vertical load tests were carried out to assess the designed performance of Type-1 and Type-2 props. Type-1 props demonstrated a "constant yielding" behavior, achieving an ultimate capacity of up to 140 kips. Type-2 props showed a "load shedding" behavior, reaching peak verti- cal loads of up to 191 kips. Buckling analysis revealed that Type-1 props were not designed to buckle, and Type-2 props failed due to buck- ling rather than material yielding. Under vertical pre-loading, lateral loading tests showed that Type-1 props can withstand about 9 kips, and Type-2 props can withstand about 10.79 kips of lateral load. This represents roughly 6% of their vertical loading capacities. Testing props under lateral loads in addition to their intended vertical loads showed that the lateral loads could influence their loading mechanisms. Type-1 props did not exhibit the expected "constant yielding" behavior under lateral load but instead showed "load shedding" decreasing their rated vertical capacity by 70%. At high vertical pre-loading, Type-2 props demonstrated "constant yielding" behavior instead of the anticipated "load shedding," leading to a 60% reduction in their rated vertical capacity. These findings provide valuable insights into the behavior of these props under different loading conditions, aiding in their efficient use and design in underground mining operations.

Jun 25, 2024