Search Documents

By G. T. Newell, J. G. Stone, V. M. Mejia

Introduction Advances in drilling have reached a point where large diameter cores can be recovered from "tight," or weakly indurated placer gravels. In such ground, core drilling can provide more reliable data regarding tenor than can be obtained using churn drilling or similar classical techniques. It can also provide metallurgical and geological information that is not available from samples obtained through alternate methods. In 1985, Coastal Mining Co, a subsidiary of M. A. Hanna, and Western Gold Reserves began to review a Tertiary placer deposit owned by San Juan Gold at North Columbia, CA, about 14 km (9 miles) northeast of Grass Valley. The deposit is one of the largest remaining unmined portions of the formerly extensive early Tertiary ancestral Yuba river system. It has been known since the 1850s, has been the subject of much technical literature, and has been the object of at least four previous drilling programs. The eastern one-third of the 6 km (3.7 mile) stretch of the channel between North Columbia and Badger Hill was partially stripped by large scale hydraulic mining in the late 1870s and early 1880s. Mining ceased in 1884 when the Sawyer Decision prohibited further discharge of hydraulic tailings into the Sacramento and San Joaquin Rivers. By that time, about 30 to 45 m (100 to 150 ft) of relatively low grade upper gravels had been removed over some 81 hm2 (200 acres). About 90 to 105 m (300 to 350 ft) of higher grade middle and lower gravels were left at least partially stripped. In 1914, a few churn holes were drilled along a widely-spaced line. In 1938-1939, Selection Trust conducted an extensive drilling campaign to evaluate the deposit. Particular attention was directed toward the partially stripped eastern portion. In 1968, the US Geological Survey drilled three churn holes in the eastern part of the deposit. The US Bureau of Mines conducted experimental mining and drilling in the Badger Hill area. In the late 1970s, Placer Service Corp. acquired a lease on the deposit. Between 1979 and 1984, Placer Service drilled 28 large diameter BADE (a German-manufactured machine) drill holes on the eastern portion of the deposit. The surviving records from the widely-spaced 1914 drilling program are fragmentary and the reported grade not well substantiated. The 1968 holes were drilled for scientific purposes. Again, drilling details are not available. However, detailed records for both the churn drilling program and the BADE program were available and formed the basis for the initial evaluation of the property. Geology The geology of the auriferous Tertiary gravels of California have been described by Whitney (1880), Lingren (1911), and, more recently, Yeend (1974). In general, the Tertiary gravels in the North Columbia area occupy a broad channel cut into pre-Tertiary igneous and metamorphic rocks. The upper, or white gravel is overlain conformably by volcanic tuffs and volcaniclastic rocks. A middle gravel is characterized by the presence of silicified and carbonized wood. A lower blue gravel unit has relatively coarser cobbles and contains a higher proportion of igneous and metamorphic cobbles than the other units. The upper gravel consists of interbedded pebbly sand and silty, or clayey sands with prominent cross bedding. Most of the pebbles are well rounded and consist mostly of white vein quartz and quartzite. The upper unit is moderately well compacted. Exposures in the walls of the old hydraulic mine pits stand at 45° and 50° angles. The gold content of the unit is well below an economic cutoff. The middle gravel - included with the upper unit by Yeend (1974) - is coarser grained, with carbonized wood, and 75 to 100 mm (3 to 4 in.) cobbles of metased-imentary and metavolcanic rocks in a sandy matrix containing abundant lithic fragments. The upper contact appears to be conformable, but the lower portion of the unit appears in places to consist of reworked lower gravels. The unit contains less clay than the upper unit and is somewhat more friable than the underlying lower gravels. The gold content, while somewhat higher than the upper level, is too low to be of ore grade. The lower gravel averages between 30 to 45 m (100 to 150 ft)

Jan 9, 1988

By R. M. Williams

Introduction Ring roller mills are efficient size reduction machines embodying the following machine functions: 1) Size Reduction: from a feed size of 2 in. to various size products as fine as 400 mesh, or granulation from 2 in. to 6 mesh containing a minimum of fines. 2) Drying: fluid bed drying of wet feed materials. 3) Conveying: negative pressure air system results in dust-free conveying. 4) Beneficiation: liberation and removal of foreign materials from the auxiliary bottom discharge simultaneously while grinding. Operation Operation of the roller mill system, Figs. 78 and 79, is completely automatic. A feeder introduces raw material into the grinding chamber in the base of the roller mill at a rate determined by pressure variations within the roller mill as material is ground and air conveyed away. The feeder will be activated by the reduced static pressure and introduce unground material into the system, thereby maintaining a constant differential pressure. Plows located ahead of each grinding roll direct the material upward and between the grinding rolls and the bull ring where it is ground to size. The grinding rolls are free to swing out centrifugally, which forces them to bear upon and grind the raw material. Being free to pivot axially, the rolls automatically assume the proper position for grinding and need no adjustment to compensate for wear. Rotation of the rolls is by rolling contact. Once ground to size, material is swept out of the mill by the controlled air flow from the centrifugal main mill fan. Air suspended, the ground material passing through the adjustable spinner separator. In the separator, an accurate size classification is made which allows product-size material to be conveyed away from the roller mill while oversize material is returned internally for additional grinding. By varying the speed of the separator drive, more or less cyclonic action is achieved at this location, effectively controlling product size. Product sized material is removed from the airstream by the cyclone collector. Typically, a conveyor or product storage bin will be located to accept the product as it exits from the bottom of the cyclone collector.

Jan 1, 1985

By Nora M. Hutt, Kevin A. Morin

There is currently some pessimism over mixing of net-acid-neutralizing (NAN) and net-acid-generating (NAG) rock to obtain indefinite near-neutral seepage from mined-rock piles. This is due in large part to the lack of well- documented, successful cases of blending and layering, and to the knowledge of unsuccessful attempts. Past work often defined a potentially successful mix in terms of the ratio of net-acid-neutralizing rock to net-acid-generating rock. For example, one case study indicated the bulk pile-wide ratio was approximately 3: 1. Since this exceeded a common ratio used in acid-base accounting, no acidic drainage was predicted. However, acidic drainage appeared within two years. A large part of the ambiguity in mixing arises from attempts to predict success based on a ratio. This paper looks in detail at simple discrete-zone mixing, where at least one truckload of NAG rock is placed in a particular location with no further rehandling or dozing. The lack of acidic drainage in this scenario is dependent on the intervening distance between the discrete NAG zones, along flowpaths occupied by NAN rock. Calculations show that the bulk mixing ratio of a mined-rock pile is not an accurate indication of whether near-neutral drainage can be maintained. For example, a pile with a bulk ratio around 300: 1 could still release some acidic drainage. Calculations also show that the minimum separation distance of the NAG zones (L) can be so great, even with typical NAG and NAN rock, that the mixed pile could safely contain only a few percent of NAG rock, which would not be sufficient for many minesites with NAG rock. The comparison to a more elaborate, computer-based statistical model shows that the simple discrete-zone approach will provide a reliable yes-no indication of whether any acidic drainage will leave a pile. However, predictions of whether combined downstream drainages will be acidic depend on numerous site-specific physical and geochemical factors within and below a pile that cannot be modelled in a general way, like the number of flowpaths and the nature of their intersections.

Jan 1, 2000

By P. R. La Pointe, H. C. Ganow

The production of both over- and undersized coal fragments is a constant problem to open pit operators in the Powder River Basin. Operators strive to achieve production blasts that economically minimize the weight percentage of over- and undersize coal. However, natural fractures influence blast fragmentation, and can impose limits on the final fragment size distribution. ARCO&apos;s Anaconda Minerals Company studied the limits placed by natural fracturing as part of a wider geotechnical study of the Wyodak Coal in the eastern Powder River Basin, Campbell County, Wyoming. Measurements of fracture orientation, size and spacing were made at ARCO&apos;s Black Thunder Mine. These data were used to form statistical distributions for natural fracture size, spacing and orientation. An algorithm was created to select fracture properties at random from these distributions and to form hypothetical blocks. The blocks were then numerically "sieved" to derive pos- sible particle size distribution curves. These curves are compared to fragmentation results from samples taken from three test blasts. All test blasts yield very similar lognormal fragment size distributions. The median particle size varies from 1.25 to 2.0 in.(3.2 to 5.1 cm), the mean from 4.0 to 8.5 in. (10.2 to 21.6 cm). The standard deviation was about 1.6 in. (4.2 cm). Coal fines (fragments < 0.25 in. or 0.64 cm) are about 15%. Calculated fragment distributions for the natural fractures predict the median size well but underestimate the variance. Algorithm modifications to account for processes known to occur in the comminution zone near the blast hole significantly improve the match in the fine coal size range. The match suggests that spacing of fractures, rather than fracture length, controls the formation of fine- and medium-sized fragments. On the other hand, the oversize coal is controlled by the fracture lengths, rather than the spacing. Data from subsequent test blasts support this idea. By increasing delay times from 8 msec to 17 msec, engineers were able to reduce fines to 7% - 10% but could achieve no further improvement, despite changes in shot pattern geometry, decking and hole size. The hypothetical fragment distributions show that, even without blast enhancement, about 5% of the natural coal blocks are fine-sized.

Jan 1, 1986

By O. A. Bascur

The problem of setting the proper control objectives and/or having several objectives to be met in the implementation of grinding control strategies can be resolved. The design and implementation of a distributed control system for safe operation of a grinding circuit while maximizing profit is presented. An optimal recovery/throughput target for a desired grind is accomplished by advanced control strategies at the DCS level. A mill load constraint control technique provides stable operation with a substantial increase in throughput, while the desired grind index is maintained by an inferential grind control technique without using a particle size analyzer. The integration of crushing/grinding and flotation in the overall design was the key to the success of the project. This synergistic effect was obtained by implementing a computer -plant management system in the concentrator. The overall philosophy of keeping the implementation simple but not simpler was used.

Jan 1, 1989

By P. Hornby, S. Henley

INTRODUCTION The project described in this paper is designed to provide a standard and flexible method by which data can be exchanged among different systems and packages in common use for geo- logical modelling and mine planning, with substantial savings in ad hoc programming which is expensive and produces interface software that is difficult to maintain. Such packages include specialised applications such as Vulcan, Surpac, Datamine, and Gemcom software, and the Whittle pit optimisation programs, and more general products such as AutoCad, Microstation, and Maplnfo, and database management systems through a generic SQL interface. The data translator is built around the CSIRO Data Model and GeoEditor, and will make widely available the benefits of the Data Model by adding functionality to its implementation in an industry- standard language and style, with interfaces to important geological and mining software products used by the industry, while including also the visualisation and editing capabilities of the GeoEditor which provides the functional framework within which the Data Translator is developed. The Data Translator is intelligent in the sense that it is not a black-box solution but allows visualisation and validation of data during transfer; furthermore it provides a means for changing abstraction levels during the transfer operation. There have been few similar efforts to address this problem. It is not a problem which is likely to be solved in any general or long- term way by any individual commercial software vendor. THE CSIRO DATA MODEL A wide variety of software tools have entered the exploration and mining industries via different pathways. Examination of these pathways and the origins of the software illuminates the types of data transfer problems and difficulties which might occur in the day to day life of exploration and mining operations. In exploration, the focus is normally on a large area (>5000km2) which is explored primarily in two dimensions. For 20 exploration purposes, geographical information systems (GIs) software, image processing software, and, in some cases, 20 computer aided design (CAD) software have been employed. Typically, GIs soft- ware is used the most by lands and tenements personnel and government geological survey organisations, image processing software is used the most by geophysicists, and 20 CAD software is used the most by drafting and geology personnel. In contrast, within the mining environment, almost all activities have 3D character. In this realm, 3D CAD software and specialised mine planning and design software are important. Specialised mine planning and design software is similar to 30 CAD software, but typically has additional capabilities such as specialised modules for surveying, drill hole data operations, open pit design and optimisation, underground mine design, mining block model creation, and/or ore reserve calculations. Unfortunately, the different origins of the software in exploration and mining lead directly to problems in data exchange and the design of seamless software systems. These problems result from the different data management strategies employed by the different classes of software. In order to address these problems, CSIRO Exploration and Mining and CSIRO Division of Information Technology have been investigating the structure, character, and syntax of data and soft- ware present in computer-aided exploration and mining activities since early 1993. The goal of this effort is to 1) systematically ex- amine the breadth and depth of the data in use within exploration and mining, and to 2) promote a data organisation strategy which is broad enough and comprehensive enough to enable wiser soft- ware design and easier data transfer. In the short term a data model can be used to improve data transfer; in the longer term it is hoped that a data model framework will help object-oriented concepts to enter the next generation of geoscientific software. The data model is described in more detail by Power et al., 1995. THE DATA TRANSLATOR PROJECT The CSIRO Data Model provides a basis for a very wide range of applications in geology and mining. It has been developed over the past two years by a joint team from the Division of Exploration and Mining and the Division of Information Technology, and its principal purpose is to provide a comprehensive and self consistent model of the geometric and topological properties of geological and mining data. The project is being carried out by CSIRO with the support of Australian mining companies through AMIRA (the Australian Mining Industries Research Association). Eight companies are sup- porting the project : • North Ltd Minenco • MIM Exploration • Fractal Graphics • BHP Australia Coal • Pacific Coal • Gencor CRA Exploration The systems to be interfaced have been decided by comparing the priorities of the various sponsors, to produce a final combined priority list as follows : • Vulcan • Minescape • Micromine • Mapinfo INTRODUCTION The project described in this paper is designed to provide a standard and flexible method by which data can be exchanged among different systems and packages in common use for geo- logical modelling and mine planning, with substantial savings in ad hoc programming which is expensive and produces interface software that is difficult to maintain. Such packages include specialised applications such as Vulcan, Surpac, Datamine, and Gemcom software, and the Whittle pit optimisation programs, and more general products such as AutoCad, Microstation, and Maplnfo, and database management systems through a generic SQL interface. The data translator is built around the CSIRO Data Model and GeoEditor, and will make widely available the benefits of the Data Model by adding functionality to its implementation in an industry- standard language and style, with interfaces to important geological and mining software products used by the industry, while including also the visualisation and editing capabilities of the GeoEditor which provides the functional framework within which the Data Translator is developed. The Data Translator is intelligent in the sense that it is not a black-box solution but allows visualisation and validation of data during transfer; furthermore it provides a means for changing abstraction levels during the transfer operation. There have been few similar efforts to address this problem. It is not a problem which is likely to be solved in any general or long- term way by any individual commercial software vendor. THE CSIRO DATA MODEL A wide variety of software tools have entered the exploration and mining industries via different pathways. Examination of these pathways and the origins of the software illuminates the types of data transfer problems and difficulties which might occur in the day to day life of exploration and mining operations. In exploration, the focus is normally on a large area (>5000km2) which is explored primarily in two dimensions. For 20 exploration purposes, geographical information systems (GIs) software, image processing software, and, in some cases, 20 computer aided design (CAD) software have been employed. Typically, GIs soft- ware is used the most by lands and tenements personnel and government geological survey organisations, image processing software is used the most by geophysicists, and 20 CAD software is used the most by drafting and geology personnel. In contrast, within the mining environment, almost all activities have 3D character. In this realm, 3D CAD software and specialised mine planning and design software are important. Specialised mine planning and design software is similar to 30 CAD software, but typically has additional capabilities such as specialised modules for surveying, drill hole data operations, open pit design and optimisation, underground mine design, mining block model creation, and/or ore reserve calculations. Unfortunately, the different origins of the software in exploration and mining lead directly to problems in data exchange and the design of seamless software systems. These problems result from the different data management strategies employed by the different classes of software. In order to address these problems, CSIRO Exploration and Mining and CSIRO Division of Information Technology have been investigating the structure, character, and syntax of data and soft- ware present in computer-aided exploration and mining activities since early 1993. The goal of this effort is to 1) systematically ex- amine the breadth and depth of the data in use within exploration and mining, and to 2) promote a data organisation strategy which is broad enough and comprehensive enough to enable wiser soft- ware design and easier data transfer. In the short term a data model can be used to improve data transfer; in the longer term it is hoped that a data model framework will help object-oriented concepts to enter the next generation of geoscientific software. The data model is described in more detail by Power et al., 1995. THE DATA TRANSLATOR PROJECT The CSIRO Data Model provides a basis for a very wide range of applications in geology and mining. It has been developed over the past two years by a joint team from the Division of Exploration and Mining and the Division of Information Technology, and its principal purpose is to provide a comprehensive and self consistent model of the geometric and topological properties of geological and mining data. The project is being carried out by CSIRO with the support of Australian mining companies through AMIRA (the Australian Mining Industries Research Association). Eight companies are sup- porting the project : • North Ltd Minenco • MIM Exploration • Fractal Graphics • BHP Australia Coal • Pacific Coal • Gencor CRA Exploration The systems to be interfaced have been decided by comparing the priorities of the various sponsors, to produce a final combined priority list as follows : • Vulcan • Minescape • Micromine • Mapinfo • Medsystem

Jan 1, 1996

By Kalle Hakalehto

Automation and mechanization in mining has no value of its own. It has to be measured in economic terms or in Increased safety or in the utilization of deposits which otherwise were unavailable. The mechanization and automation of workphases in the mining and rock construction process has led to the decrease of manual work. This has had a very essential importance in the countries where the labor is expensive or where there has been difficulties in the availability of labor. The work has become much more efficient. We would like to argue that the need of mechanization has been initiated mostly from the above mentioned reasons. The origin has seldom been the "process" approach or the real need or will to change the way mining is done. Through mechanization bigger unit sizes of machines and operations have become possible and better efficiency is achieved. This has led to new problems as well, but in most cases they have been solved so that better and more economic outcome than before has been the end result. The changes have thus been justified. It is perhaps feasible to state already at this stage that we see that the mechanization andautomation steps in the difficult conditions of mining have been remarkable. There is not a slightest underestimation of the achievements and importance of this development in our mind. Where we are to- day is the result of the experience, know-how and technological excellency of all the parties involved. The natural approach to automation has been through mechanization and automation of individual unit operations and machines. This has been the way as well in manufacturing industry as in mining. There may not have been any other way. The other presentations in this session tell us very clearly of the approach .which the machine manufacturers have taken. They have not done it alone but &apos;most of the initiatives have come from them. A good use of their present achievements gives many possibilities to increase the, efficiency in mining. We would, however, like to extend the view one step further to the future:

Jan 1, 1989

By D. M. Milne, H. H. Kanduth

INTRODUCTION The past few years has seen an increased interest in the determination of statistically valid properties of a rock mass. The increased use of computer modelling for the study of rock excavation behaviour has created a need for upper and lower statistical bounds for the properties of a rock mass being modelled. Obviously, to determine the statistical properties of a large volume of rock, many samples must be tested - an expensive proposition when using conventional testing facilities and procedures. As a result of high costs per sample, sufficient tests for statistically valid results are rarely done. In an effort to reduce both sample preparation and test facility costs, an instrument called the Bemek Advanced Rock Tester (BRT) was developed in Sweden. With a total weight of approx. 35 kg, the BRT is portable and sells at a small fraction of the cost of a conventional testing machine. It is comprised of a small 65 KN loading frame with attachments for a variety of tests (see Table 1) , a hand operated hydraulic pump, an electronic balancing unit and a programmable microprocessor. The microprocessor is capable of storing data, performing arithmetic operation on, and printing signals from, a transducer and two strain gauges. A detailed description of the apparatus is given by G. Swan et al. (1). The proposed test strategy involves first a 3-point flexure test on a notched core specimen, followed by a 4-point flexure test on the separated specimen halves. Finally, point load and Brazilian tests can be carried out on the quarter parts of the original specimen. Thus specimen preparation is kept to a minimum. These and other perceived advantages have prompted the purchase of this machine and an evaluation of its suitability to provide data on mechanical properties of intact rock for numerical modelling and rock mechanics design at Noranda&apos;s underground mines. Details of its performance evaluation and experiences with the unit are discussed in the following sections. [ ] INITIAL OPERATING EXPERIENCE During the commissioning stage the BRT had, or developed, a series of problems, some of which seriously affected its operation. Below are some examples. Poor documentation was the most serious problem encountered. Confusing instructions for the 4-point bend test installation and its microprocessor programing, as well as poor and ambiguous information on the calculation of gauge factors, are some of the difficulties which had to be overcome. Meehan~cal problems occurred, including failure of the hydraulic pump, as well as electronic difficulties with the microprocessor. Other problems with the printer, requiring its replaceqent, were fortunately covered under warranty.

Jan 1, 1986

By Thomas R. Kuesel

In simpler times, construction was a cooperative undertaking. The frontier tradition of barn-raising is the construction equivalent of the academic ideal of a single student seated on a log with Horace Greeley. In a more complex world, ideals become more elusive. Still, it was only a generation ago that toll revenue bond financed projects generally involved a team composed of investment bankers, engineers, and construction contractors, who all shared a common objective -- to create something useful, at minimum cost and in minimum time, with fair compensation to all involved. In an increasingly contentious public climate, the team has too frequently been splintered into separate camps of owners, engineers, and contractors, who have lost the old objective of creation and have, under the guidance and control of the lawyers, substituted two new primary objectives: 1. To protect one&apos;s own skin. 2. To detect and punish culpable negligence of one of the other parties. This process has become so ludicrous that a number of thoughtful observers from all of the camps (including even some lawyers) have come to recognize that there must be a better way to undertake construction works than to use them as wrestling arenas. The road to improved contracting methods starts with mutual understanding of each other&apos;s problems and viewpoints. To this end, discussions such as this RETC session make a useful contribution. To

Jan 1, 1983

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

10.1 I~RODUC1&apos;ION In order to understand the effects of surface subsidence due to underground mining on the ground water hydrology, a brief introduction to the rate, direction, and general pattern of ground water movement in aquifers is necessary. Ground water movement in an aquifer is controlled by aquifer lithology, structure, permeability, water levels, topographic set¬ting, and pumping patterns (Sgambat et al., 1980). Fig. 10.1 shows an idealized flow pattern of ground water in a hilly terrain (Coe and Stowe, 1984). The hill is made up of a series of interbedded permeable aquifers (mostly sandstone) and confining units (mostly shale). Since sandstone is porous and permeable, ground water moves through it downward and laterally until it reaches the interbeddings of the confining unit immediately below. The ground water then moves laterally along the interbeddings, be¬cause the confining unit is less permeable, and comes out as springs on the surface at the intersection of the aquifer and the confining unit. If there is a ground water table in each aquifer, it is a perched water table (e.g., right side of Fig 10.1). On the other hand, if the ground water recharge is larger than can be drained out, the interbedded permeable aquifers and confining units will be filled with water and a ground water table will exist only at the uppermost permeable aquifer. This is the semi-perched water table (e.g., left side of Fig. 10.1). There are three ground water flow systems: shallow, interme¬diate, and deep. Shallow flow systems occur near the land surface and the surface drainage system. The flow depth ranges from a few to several hundreds of feet with a resident time of a few weeks to a few years after entry, depending on the permeability of the rock strata. In a shallow flow system, the drainage coincides with sur¬face run-off water divides. Intermediate flow systems occur in minor hills some distance away from surface drainage. The travel distance ranges from several hundreds to several thousands of feet, the travel time from several months to tens of years. These systems are less dependent on seasonal recharge or discharge. In deep flow systems, the ground water travels from thousands of feet to miles, and transfers between surface basins. The travel time ranges from several tens to several hundreds of years. The systems generally receive recharge over a large area on major mountains and dis¬charge into major stream systems. 10.2 CASE STUDIES There are two ways of monitoring water wells for studying the effects of dewatering due to underground mining, i.e., water level and piezometric level. The water level is the water elevation in a water well that has penetrated two or more aquifers. Thus it indi¬cates the combined flow of all the aquifers that the water well intersects during the time of measurement. The piezometric level is the level to which water rises in a piezometer cased to a specific aquifer, and coincides with the pressure level of water in that aquifer. Therefore piezometric level reflects the water condition in that particular aquifer to which it is confined, while the water level represents the total yield of a water well without regard to the source of water. For instance, if a water well intersects two aqui¬fers, and if the lower aquifer is affected by undermining and goes dry while the upper aquifer does not, the water level in the well will drop, but may never go dry. Under this condition, the data obtained by monitoring the water level do not indicate the true behavior of the individual aquifers, especially if they are located at widely separated heights. 10.2.1 WATER LEVEL EFFECTS The effects of underground mining on ground water flow have been the subject of many investigations (Booth, 1984; Coe and Stowe, 1984; Owili-Eger, 1983; Rauch et al., 1984). However, the problems are very complicated, as have been exemplified by the conflicting conclusions reached by various investigators in var¬ious case studies. The most dramatic examples were described by Coe and Stowe (1984). In the first case (Fig. 10.2), the coal seam was 5 ft thick with cover from 400 to 800 ft deep. The majority of water supplies came from a sandstone aquifer in most ridge tops. When the face of the Panel No. 3 passed under it, dug well WW-1, which was approximately 670 ft above the coal, went dry, while the water level in Borehole B- 1, which was located at the center of Panel No. 4 with the bottom reaching the coal seam, also dropped about 160 ft. In Panel No. 5, the developed spring DS-2, which originated from the surface of the sandstone/shale contact and was approximately 750 ft above the coal seam, stopped when the face passed under it. The water level in the dug well W-2, which was dug into the shale about 700 ft above the coal seam dropped about 22 ft, but the well did not go dry. Therefore, nearly every spring or well located above or near the active panels was affected by longwall mining. In the second mine (Fig. 10.3), the seam was 5 ft thick with cover from 200 to 400 ft thick. Dug well DW-2, the bottom of which was 35 ft deep and approximately 330 ft above the coal seam in a perched sandstone aquifer, went dry right after the longwall passed under it. Drilled well W-3, in the sandstone aquifer, about 220 ft above the coal seam, experienced a 75-ft drop in water level when the face was under it, but showed some re¬covery after the face had passed under it. Ponds P- I and P-2 were developed in shale bedrock and were spring fed. They were not affected by longwall mining. Pond P-3 was developed in the sand¬stone aquifer, and its water table showed some decline when the face passed under it. Spring ST-1, which originated from Pond P-1 and was fed from several tributary valleys, was affected by longwall mining, probably because it passed across the panel edges where tension cracks drained off the water. Although the overbur¬den in case 2 was about half of that in case 1, the majority of water resources were not affected by longwall mining. Coe and Stowe (1984) attributed this discrepancy to: (1) a higher percentage of clays, shales, and claystones, resulting in a lesser degree of inter¬connected fracturing, and (2) a less rugged topography resulting in a less localized ground water flow system. Therefore, in order to assess the effects of underground mining, the premining ground water flow patterns, topographical, lithological, and meterological conditions must be known. Booth (1984) also monitored the ground water effects of a longwall mine (Fig. 10.4) in a seam 5 ft thick and 300 to 800 ft deep. There were three major aquifers: Morgantown sandstone approximately 30 ft thick and 630 ft above the coal; Saltsburg sandstone of up to 50 ft in thickness and 520 ft above the coal; and

Jan 1, 1992

By L. Yuan, J. Soles, D. Bahrami, W. Tang, R. Thomas

Mine equipment fires remain as one of the most concerning safety issues in the mining industry, and most equipment fires were caused by hot surface ignitions. Detailed experimental investigations were conducted at the NIOSH Pittsburgh Mining Research Division on hot surface ignition of liquid fuels under ventilation in a mining environment. Three types of metal surface materials (stainless steel, cast iron, carbon steel), three types of liquids (diesel fuel, hydraulic fluid, engine oil), four air ventilation speeds (0, 0.5, 1.5, 3 m/s) were used to study the hot surface ignition probability under these conditions. Visual observation and thermocouples attached on the metal surface were used to indicate the hot surface ignition from the measured temperatures. Results show that the type of metal has a noticeable effect on the hot surface ignition, while ventilation speed has a mixed influence on ignition. Different types of liquid fuels also show different ranges of ignition temperature. Results from this work can be used to help understand equipment mine fires and develop mitigation strategies.

Mar 2, 2022

The Mesquite mine is being operated by Gold Fields Operating Co.-Mesquite, a subsidiary of Gold Fields Mining Corp. The mine Is located in southeastern California about 56 km (35 miles) east of the farming community of Brawley, California. The mine has been in commercial production since early 1986 and Is a conventional open pit mine developed on 6.1 m (20 foot) benches. The gold is recovered by heap leach using permanent heaps built in multiple 6.1 m (20 foot) lifts. This year&apos;s gold production will be in the range of 5,600 kg (180,000 troy ounces). Current ore production is about 18,140 tonnes (20,000 tons) per day while the total tons mined Is averaging 65,000 tonnes (72,000 tons) per day. The climate at the mine is extremely arid with rainfall of 7.6 cm (3 inches) per year. From early May until late October daytime temperatures generally exceed 37.8 degrees Celsius (100 degrees Fahrenheit) and can be as high as 37.9 degrees Celsius (120 degrees Fahrenheit).

Jan 1, 1989

By G. Robert Moorehead, Peter T. Luckie, Harold L. Lovell, David J. Akers, James K. Kindig

Jigging is a process of particle stratification in which the particle re- arrangement results from an alternate expansion and compaction of a bed of particles by pulsating fluid flow. The vertical direction of fluid flow is reversed periodically. The rearrangement results in layers of particles that are arranged by increasing density from top to bottom of the bed. This response, developed from the many and continuously varying forces acting upon the particles, permits a solid-solid separation more related to particle density and less to particle size than any other "hydraulic-type" process. The stratification is usually carried out in a rectangular, open-top container called a jig, in which the mass of particles (termed a "bed") is supported on a perforated base through which the water flows in alternating directions. The coal particles, in addition to the vertically expanded and compacted bed motion, move continuously, horizontally across the supporting screen. Following the particle stratification, the particle bed is physically "cut" at a desired horizontal particle density plane to separate the desired clean coal product from the more dense refuse. The jig system includes means for continuously introducing the raw coal and for moving the water through the coal bed in a controllable manner, as well as for separating and removing the stratified particles from the system as two or more product streams. In coal preparation, this highly versatile unit operation is applied preferably to a wide size range of particles with top sizes up to 8 in. (20 cm) rather than to a closely sized fraction. In gravity ranges, the process has been applied to gold particles with a density of 19.3 and to coal particles having densities less than 1.30. Single jig washers have capacities from 5 (4.6) to greater than 700 tph (637 t/h) of feed coal. The separation results attainable by jigging have favored this unit operation as optimum for creating a clean coal product as required by steam coal specifications. Al- though the jig is used in preparing coals which are difficult to separate, its limitations to achieve both quality products and high recovery are being recognized in comparison with heavy media-based processes which make sharper separations from feeds having high "near-gravity" contents. The accu- racy of the densimetric stratification in the upper portions of the jig bed are less precise. It follows that coals with more than 10% near-gravity material

Jan 1, 1991

By M. Murphy

The multibillion dollar cost of cleaning up thousands of environmentally contaminated sites across the country created by decades of inadequate disposal of hazardous waste has led to a search for "deep-pocket" sources of cleanup funds. The resul1:: is the emergence of a growing body of law that could have a profound impact on commercial financing transactions and other investment activities when present or past owners of contaminated property are involved.

Jan 1, 1988

By Kenneth S. Johnson

Oklahoma is a region of complex geology where a mobile belt of Paleozoic geosynclines and uplifts on the south abuts against the margin of the North American craton to the north. The state contains many classic areas where fundamental concepts of sedimentation, stratigraphy, structural geology, historical geology, mineral investigation, and petroleum exploration have been formulated through the years. In the southern Oklahoma mountain belts, there are exposed a great variety of igneous and sedimentary rock units seen at few other places in the Midcontinent area. Major geologic provinces of Oklahoma (Fig. 1) include: (1) the cratonic and relatively stable northern shelf areas, including the Ozark uplift; (2) the Ouachita geosyncline (now the Ouachita Mountain belt) and associated Arkoma basin in the southeast; and (3) the southern Oklahoma aulacogen (geosyncline), comprising the area of Anadarko, Ardmore, Marietta, and Hollis basins, as well as the Arbuckle and Wichita Mountain uplifts. The three principal fold belts, the Ouachitas, Arbuckles, and Wichitas, all originated from a series of Pennsylvanian orogenies (about 300 million years ago) in the two Paleozoic geosynclines.

Jan 1, 1999

By D. V. Professor Keller

The production of premium coal-based fuels (<3% ash) and ultra clean coals (<1% ash) using the process of selective agglomeration requires proper selection of raw coal, rough preparation procedures, milling equipment, product coal size distribution, water purity, agglomerants, agglomeration equipment and operational procedures. Each of the variables can contribute a small fraction to the impurity load in the product coal or limit the ability of the process to separate mineral matter-free coal. Each of the variables and their importance will be examined from data produced at the bench by batch and continuous agglomeratons as well as the results from pilot plant and tonnage production units. The results are discussed which have indicated that some standard commercial coals can be produced with ash contents as low as 0.2 % ash (batch/bench) and several tonnage lots of 0.6% ash in as 200 lb/hr pilot plant. In most cases iron pyrite released from the coal matrix and with proper pH control is rejected from the product coal agglomerates.

Jan 1, 1995

By Hetland Donald L.

Regional Tertiary formations and basins of local sedimentation which contain uranium deposits west of the Rocky Mountains are mainly of Oligocene, Miocene, and Pliocene age (fig. 1). The host rocks have been derived mainly from intrusive and extrusive igneous rock. The major host formations which cover broad geographic areas include the Esmeralda, Truckee, Humboldt, Thousand Creeks, Payette, Panaca, Cedarville, Coso, and San Joaquin Formations. Local areas of Tertiary sedimentation containing uranium deposits occur near Yuma, Safford and Artillery Peak, Arizona; Dillon and Canyon Ferry, Montana; Spokane Indian Reservation and Pend Orielle River, Washington; Topaz Mountain, Utah; Stanley Basin, Idaho; and Sonora Pass, California. Uranium deposits in these sediments have been classified into five categories based on environment (fig. 2). They are: (1) Deposits in lake sediments consisting mainly of water-laid tuffs; (2) Deposits in lake sediments intruded by volcanic plugs; (3) Deposits in lake sediments interbedded with arkoses near batholiths; (4) Deposits in coarse volcanic sediments in local sedimentary basins; (5) Deposits in arkosic conglomerates in local sedimentary basins.

Jan 1, 1969

By Gülhan Özbayoglu, Yusuf Ziya Akgök

The effect of cooling rate on the flotation behaviour of copper slags of flash smelter plant in Samsun was investigated. Fresh molten slag was solidified in laboratory scale in three different ways. All the samples were characterized by chemical and mineralogical analyses. The chemical analyses showed that samples prepared from fresh slag had 0.9 to 1 % Cu with 40 % Fe and 30 to 32 % SO2. Old pit slag samples contained between 1 to 3% copper. Microphotographs showed that rapidly cooled slags showed fine size distributions, e.g. the copper grains in granulated slag had sizes in 1-2 microns. On the other hand, the size of copper grains in slowly cooled slags increased above 40 microns. Flotation tests carried out by using potassium amyl xanthate and Flotanol-C showed that slowly cooled slag reduced the copper losses in the tailing and improved the grade of concentrate. Under the light of laboratory investigation, the pit dimensions of Samsun Plant have been modified which resulted in a pronounced improvement of the grade and recovery of concentrate produced at Samsun slag flotation circuit.

Jan 1, 1995

By B. J. Arnold, F. F. Aplan

Prior laboratory work has demonstrated that much of the fine ash forming minerals entering a flotation froth are there as a result of water carryover- from the bulk contents of the flotation cell (Arnold and Aplan, 1986a). Using a bank of four 8.5 m3 (300 cu ft) Wemco flotation cells cleaning a well-liberated Lower Kittanning seam coal, test results show that the sulfur and ash content of the froth is directly related to the water content of the froth (or inversely related to the percent solids in the froth). Reagent changes that result in a watery froth produce a higher ash content in the froth. A direct comparison of laboratory and plant results show that the standard laboratory flotation test produces a product higher in sulfur and ash than that produced in the plant. Caution should be exercised when extrapolating laboratory test results to the plant situation. A method of estimating coal flotation product quality in the plant based on laboratory tests is given.

Jan 1, 1991

By A. G. Mayton, L. Adler

The paper under discussion provides an excellent and concise study of compartment ergonomics for thin seam equipment. However, in accomplishing this, some very important operational aspects were ignored. Since these are likely to be determinant, the authors&apos; response is solicited. The novel shuttle car with its cross-car, end-mounted compartment is operationally very different from the current one. The latter can be considered a highly mobile extension of the continuous miner or loader, with a pass-through conveyor, dump boom, and extra storage. As such, the vehicle&apos;s kinematics are the simple "I," or shuttle pattern, bent for going around pillars, with an intermediate stop at the "change-out point" (Adler, 1986 ). The action of the cable reel adjusts well to this pattern. The proposed shuttle car&apos;s motion either superimposes a "Y," time is lost (5 seconds) for each cycle, space is needed, line of sight is compromised, and a cable anchor is probably required at the dump. A chute is almost prohibitive in construction time and cost. The lack of a dump boom further curtails flexibility in the proposal. The value of a standard hand and opposite standard hand configuration also needs consideration. Many front-end loaders have a rocker (overshot) capability that is designed to achieve an "I” pattern. And crawler loaders sometimes use a side dumping bucket variant for the same purpose. These examples indicate the pattern&apos;s importance. For underground, thin seam application, the ram car has become popular. This is an articulated truck, battery-powered, and with an ejector dump. Its operational patterns would be similar to the novel shuttle car, except without the loading flexibility provided by a conveyor. Since the cab location of the proposed shuttle car largely obviates some of the major advantages of the present shuttle car, the question arises whether this configuration could be adapted to the current ram car and scoop

Jan 1, 1991