Search Documents

By Nick Katsikaros, A H. Gray

Gold concentrates are produced at many mines by a variety of centrifugal and gravity machines, such as Knelson and Falcon concentrators, however the subsequent recovery of gold is relatively inefficient and subject to security problems. The InLine Leach Reactor (ILR) offers a new method to recover over 95% of gold in concentrates using a simple, secure leaching process. The InLine Leach Reactor is of particular benefit in treating slow or difficult leaching sulphide concentrates and its performance can be reliably predicted from simple laboratory tests. The InLine Leach Reactor is now successfully operating in two gold mines providing benefits of high gold recovery, low operating costs, high security and ease of operation.

Jan 1, 1999

By M. E. Poad

The Research and development review arrived too late to appear in the May issue. The competitiveness of the US mining industry in a world market depends on many factors. The introduction of new and innovative methods, though, can have a significant, long-term impact. As industry cuts back its own long- term research and development efforts, the federal government continues to provide the major support for mining and minerals research. The US Bureau of Mines works with the mining industry and the academic community to develop innovative concepts for the mining and processing of non-fuel minerals. The Bureau’s research focuses on exploration and mining technology, minerals and materials science, processing technology, health and safety and environmental technology. Mine design A conical caving system, being designed by the Bureau, would allow the development of low-grade ore bodies, early startup at lower initial capital costs and increased safety and versatility in development and production. This method is a form of mass caving that allows the ore to be drawn from a central loading point at the bottom of the cone- shaped caving zone (Fig. 1). A simulation laboratory model and computer analysis show initial promise for predicted performance. For tabular, flat-lying ore deposits, the Bureau is investigating a version of the Finnish slot-and-fill system. For this total extraction method, a pattern of rectangular panels is laid out. One panel is extracted in a series of parallel slots and is replaced by alternating-row pillars of backfill. After one panel is mined, equipment and operations are transferred to another panel. By transforming this rectangular layout to a curvilinear geometry, one continuous spiral can be mined without re positioning equipment. Instead of parallel slots and pillars aligned in a rectangle, the slots and pillars are arranged in a spiral.

Jan 1, 1992

By T. Simpson

European industrial policy seeks to provide the right framework conditions to allow companies to develop and innovate and to make the EU an attractive place for job creation. This includes providing the basis for a competitive manufacturing industry which provides around 20% of EU economic output and employment for about 34 million people. The EU non-energy extractive industry with an annual turnover of around ?40 billion and a direct workforce of about 270,000 people is considerably smaller, but it plays a vital role in providing much of the manufacturing sector with raw materials. It also supplies very large quantities of minerals such as aggregates and natural stone to the construction industry, facilitating the development of modern infrastructure such as roads, railways, houses, schools and hospitals. However, despite an active extractive industry, Europe is increasingly dependent on imports of raw materials and particularly metallic ores and concentrates. In 2005, the trade deficit for minerals was in excess of ?11 billion, of which ?10 billion related to metallic minerals. Such import dependency is not a new phenomenon, but the rapid industrialisation of developing countries such as China and India has significantly increased global demand, resulting in large price increases for downstream industries and at times, bottlenecks in supply. The impact of this and other competitive pressures on some sectors of the European manufacturing industry, including the possibility of them being lost to lower cost countries outside Europe, has moved the issue of industrial policy and access to raw materials up the political agenda. A number of measures have already been announced by the European Commission to address these issues including: - The analysis of the competitiveness of individual industrial sectors, in order to understand their specific needs and take account of the particular opportunities and challenges they face.

Jan 1, 2006

By John P. Albers

During the 1950's and 1960's a program of geologic mapping of counties has been underway in Nevada by geologists of the U. S. Geological Survey and the Nevada Bureau of Mines. The aping has been done principally at reconnaissance scales, with more detailed work in local areas. Geologic maps are either published or open-filed for about a dozen counties at scales of 1:200,000 or 1:250,000. One by-product of the geologic mapping has been the recognition of about 80 Tertiary volcanic centers from which large or very large volumes of volcanic material ranging from rhyolitic to andesitic in composition have been erupted. For purposes of this discussion these are regarded as the major centers; the tally does not include hundreds and perhaps thousands of small rhyolitic domes and plugs and basaltic vents. About 15 to 20 of the 80 major centers are believed to be calderas ranging in diameter from 3 to 25 miles. Some have been described in the literature by geologists of the Nevada Test Site and others. However, the vast majority of the 80 centers have not been described in print, and we are indebted to our colleagues for locating them for us in many of the counties. Briefly, we would like to express our appreciation to the following people all members of the USGS unless identified otherwise: Robert Coast, who has identified the centers in Elko County; Ron Willden, Robert Yates, and

Jan 1, 1968

By George A. Desborough, David L. Fey, Stanley E. Church

About 100 mine-waste dumps from past metal exploration and mining in Colorado and Montana were sampled using surficial-sampling methods for laboratory studies of the minus-2-mm fraction. In the laboratory, the composite samples were split into l00g samples that were leached to assess their acid-generation potential and associated release of potentially toxic metals that may degrade water quality in the headwaters of the Animas River watershed in Colorado and the Boulder River watershed in Montana. Two leach methods were studied: a passive leach using de-ionized water, and a more aggressive leach following the EPA-1312 method. The resulting pH values of the leachates using both methods are comparable. The concentrations of sulfate and several, but not all, dissolved or water-soluble metals are higher in the EPA-1312 leachates than in the passive leachates; however, the overall trends of the data are very similar. The passive leach method is less labor intensive and may be more representative of the natural weathering process occurring on the mine-waste dumps, simulating the natural precipitation and snowmelt. Three chemical characteristics of mine wastes studied here provide a relative ranking of mine-waste dumps for the purpose of determining priority for removal or remediation. These characteristics are: net acid production (NAP), sum of dissolved toxic metals (?As+Cd+Cu+Pb+Zn), and dissolved iron in leachates. Ranking can be done evaluating plots of NAP versus the sum of dissolved toxic metals, and NAP versus dissolved iron. These two plots serve as a basis for relative ranking of polymetallic-vein and acid-sulfate mine wastes studied. This ranking scheme may apply to mine wastes from production of other deposit types in other watersheds.

Jan 1, 2000

By Ian Sheppard, John J. Chen

This paper describes the development of the underground mining methods employed for narrow silver-lead-zinc orebodies at the Isa Lead Mine. Cut-and-fill methods were the chief underground mining methods for the narrow orebodies at the mine over 35 years ago. Benching methods were introduced approximately two decades later, and quickly replacing the cut-and-fill methods. The cut-and-fill methods and the benching methods are briefly reviewed in the paper. The benching methods and technologies have been continually evolving and one of the recent achievements is a multi-lift benching method. The multi-lift benching method is described in detail.

Jan 1, 2001

By Heinrich H. Becker, Vladimir L. Konyukh, Sergey P. Koltsov, Valery A. Davidenkol

Ramifide conveyor transport of the biggest russian coal mine "Raspadskaya" is simulated by Petri nets. There are 6 longwalls with accidental output. 12 belts, and 5 transfer bunkers at this mine. It is necessary to coordinate transport links for recon- structed conveyor system. Many tasks were solved by dynamic simulation, such as estimation of transport lateness, influence of transfer bunkers on an unevenness of total coal flow, maximum filling of each bunker, maximum time of main conveyor refusal, co-ordination of unloading for dependent bunkers, choice of main conveyor. The problem of mine-wide conveyor transport animation for dispatcher is formulated in reference to mine "Komsomolets". OBJECT OF SIMULATION The biggest russian coal mine "Raspadskaya" is situated on a south part of Kusnetski coal basin (West Siberia). One mines about 20.000 tons of coal out of flat seams by 2.2-4.5 m thickness in a day. There are 6 fully- mechanized longwalls by output 720- 3600 tons in a shift in mine. Coal haulage to surface is carried out by 12 belts having 1.6 - 4.3 km length. For a smoothing over un- evenness of coal flows 5 transfer bunkers to 300 tons were intro- duced. The designed conveyor system is divided into two parts (Figure 1). In the upper part some coal from Face 1 comes through belt road C, into transfer bunker 8,. From the opposite side that bun-

Jan 1, 1996

By C. D. Breeds, F. E. Valencia, J. H. Pye

The "FIRST AUTOMATIC SHOTCRETE TECHNIQUE" (F.A.S.T.) system, provides safe, efficient methods of remotely lining, shafts/raises. Two systems are available; one system will be used to shotcrete a 3.04m (10-ft.) diameter ventilation raise at a mine in Mexico; the other system incorporating remote control and sensing devices will to used to shotcrete ventilation raises from 2.75-4.9m (9-16 ft.) in diameter. This paper describes development of the system, from idea to field use.

Jan 1, 1981

By M. K. Gangal, E. D. Dainty

CANMET/MRL has been contributing to an industry/government program to assess the quality of air in mines, and improve the working environment for Canadian miners. The ultimate aim of this program is to recommend a sampling methodology and appropriate concentration limits for both the soot (diesel particulate matter - DPM) generated by diesel equipment, and respirable combustible dust (RCD) as measured underground. The program was conceived by the Canadian Adhoc Diesel Committee, which consists of representatives from seven major Canadian mining companies, three provincial inspectorates, one union representative, two manufacturers of diesel equipment, and CANMET, a Federal Canadian research agency. This paper describes the modification and laboratory confirmation of an existing methodology for the sampling and analysis of DPM/RCD, including: sampling problems, filter selection, filter efficiency, DPM size distribution, the approximate performance of fractionating devices, and it reports the results of current ambient measurements of exposure levels in Canadian underground mines. Because of the concern about the health impact of DPM/RCD on mine workers, North American agencies are in the process of establishing limits for these aerosols. So far, the Province of British Columbia is the only jurisdiction in North America to legislate the maximum exposure level of RCD in its underground mines, i.e. 1.5 mg/m3 interim level recommended by the Adhoc Diesel Committee. It has also recommended the use of the CANMET/ADHOC RCD sampling protocol.

Jan 1, 1993

By John C. Edwards, F. Friel, John J. Opferman, Robert A. Franks

A series of diesel fuel fire experiments were conducted in the Pittsburgh Research Center's Safety Research Coal Mine (SRCM) to determine products-of combustion (POC) spread rates along a single entry under zero imposed airflow conditions. Six experiments with an average fire intensity of 330 kW and three experiments with an average fire intensity of 30 kW were con- ducted in a 180 m long entry which had an average 2 m height and 4 m width. POC spread rates were measured by the response time of diffusion type CO detectors, positioned at 30 m intervals, to CO concentrations 5 ppm above ambient. For the 330 kW fires, average POC spread rates of 0.22, 0.1 3, and 0.06 m/s were determined at 30, 60, and 90 m distances from the fire. For the 30 kW fires these average spread rates were reduced to 0.08, 0.04, and 0.04 m/s. The measured maximum roof layer temperature 30 m from two of the 330 kW fire was 30 and 36"C, which is less than the 57°C alarm point of a typical mine thermal sensor. It was determined that smoke detectors can be more effective for mine fire detection than CO detectors. The experimentally determined POC spread rates can be used to provide guidance for specification of sensor spacing to improve early fire detection at zero or very low air flows.

Jan 1, 1997

By S. G. Malghan, W. H. Moyer

In reference to the section "Excess pyrite," the author discusses difficulties in separating chalcopyrite from pyrite. A technique does exist, and has been used commercially, for the flotation, separation, and recovery, if desired, of both chalcopyrite and pyrite. The method was described in Mining Engineering, March 1966, "An Improved Flotation Method for Cornwall Sulfides." While it was not used on a porphyry copper ore, it was used on a chalcopyrite- pyrite-containing ore and might well have application. Both sulfides, chalcopyrite and pyrite, were floated simultaneously using xanthate as a collector and MIBC frother to produce a cleaned sulfide product. This concentrate was then thickened and conditioned at high solids with aeration and lime to a pH above 12.0 for a period of 1.5 to 2 hr. A supplemental suppressant, such as cyanide, could be used if necessary to sharpen the subsequent separation; however, it was not required at Cornwall. The conditioned sulfides were floated with two stages of cleaning to produce a high- grade chalcopyrite froth product and a pyrite sink product barren in copper. The separation at Cornwall gave a 28.6% Cu grade chalcopyrite product and a pyrite analyzing 0.06% Cu. A desliming step on the raw ore initially used at Cornwall for a period of time was later discontinued. Advantages to be found in using a strong sulfide collector, such as a xanthate, is the rapid flotation it induces and, generally, an ability to float at a coarser grind. A following regrind circuit could be used to give maximum liberation and produce a clean sulfide concentration. The "differential" separation is concerned primarily with grade and with assuring a barren pyrite for maximum recovery.

Jan 1, 1987

By Jon Holder, Brann Johnson

Pore-fluid/rock chemical interactions on both short and long time scales can produce significant pore structure and mineralic changes that can markedly alter transport properties, such as fluid permeability. The introduction of the chemical factor requires modification of experimental systems and methodologies developed for measurements in which chemical effects are minimal. Particular attention must be given to temperature effects, fluid chemistry, fluid/rock reactions and kinetics, fluid flow rate, and fluid/experimental-system reactions. The ability to obtain very low, steady flow rates at constant fluid pressure is important for study of some fluid/rock systems. Minimization of metal corrosion is of paramount importance and requires choice of proper metals, such as titanium, and certain Ti-alloys and Ni-alloys. In this paper, we briefly discuss the relevant chemical factors affecting system and experimental design. The primary focus, however, is on the characteristics of highly corrosion resistant metals, thermal and chemical resistant jacketing materials, and the attributes and limitations of various flow-rate and back-pressure control systems and flow-rate measurement systems.

Jan 1, 1986

By Lit-Mian Chan, David H. Carlson, John H. Johnson

This paper presents an apparatus and procedures to implement a methodology for controlling ambient air quality in a confined working environment, such as an underground mine, an underground storage area, or a tunnel. The air quality control methodology is directed at limiting the quantities of exhaust pollutants emitted by diesel-powered vehicles into the confined space by identifying vehicles that are excessive polluters. The methodology is based on tailpipe and ambient air measurements in the confined space, and the ambient air threshold limit values (TLVs) for the various diesel exhaust pollutants. The methodology consists of two computational methods; a deterioration criteria computational method to identify excessive polluting vehicles, and an engine performance computational method to determine engine performance and to provide information needed to diagnose engine faults. The methodology is designed for implementation in conjunction with a preventive maintenance program. The first part of the paper describes the mine air and tailpipe emissions measurement apparatus and techniques used to obtain data. This is followed by sections discussing the deterioration criteria and the engine performance computational methods. A section discussing some common engine emissions-related faults is also presented. Lastly, a proposed procedure to implement the methodology including a possible hierarchical structure for mine personnel involved to implement the procedures is presented.

Jan 1, 1993

By Mike Irish, Deb Mukhapodhyay

It has been demonstrated by Arrowhead Industrial Water that a proprietary reverse osmosis technology can be used efficiently, effectively, and economically to reduce the levels of cyanide species, heavy metals, and other ions as shown in Figure 1 to allow safe discharge of a permeate solution to the environment. A simultaneous benefit of this process was the cost savings of reduction in quantities of cyanide requiring destruction by hydrogen peroxide and recovery of a concentrated gold and silver value in the concentrate solution.

Jan 1, 1992

By Dennis Dolinar

Improperly designed support systems have led to unplanned roof falls in longwall tailgates. To prevent such falls requires appropriate support and adequately designed support systems. The National Institute for Occupational Safety and Health (NIOSH) is currently developing a standing support design methodology based on the ground reaction curve. To design the support system with this methodology requires a quantitative assessment of the ground and support interaction, which is developed from instrumented test sites installed in longwall tailgates. To compliment and expand the field data results and to optimize the support design, numerical modeling is also conducted. The models are calibrated from the test site data. In the present study, data was obtained from a longwall tailgate in the Illinois basin. The test site was located in the Herrin No. 6 coal seam at a depth of 500 ft. At the site, the immediate roof was a weak shale overlain by a competent limestone. Above the limestone, sandstone formed the intermediate roof. The floor consisted of a weak underclay. In the study, the performance and interaction with the surrounding rock mass of two different standing supports, an engineered crib and a conventional 4-point wood crib were monitored. The two cribs have similar load-displacement characteristics at least through 6 in of displacement. Beyond 6 in, the engineered crib becomes unstable and begins to strain soften and shed load. The measurements and developed ground reaction curves indicated that the tailgate at the mine was a low convergence environment until well inby the face. Because the convergence was well below their capacity, both supports provide more than adequate levels of support to the tailgate. Significant convergence and support loading did not occur until 90 to 100 ft inby the face. The results of this study were also compared with results from similar studies conducted in the Pittsburgh seam to further advance the development of the ?ground reaction curve? based support system design.

Jan 1, 2009

By Carl R. Peterson, John Herrick

INTRODUCTION The need for substantial advances in underground excavation technology has produced considerable research activity on a wide variety of concepts under a variety of Government funded programs. One goal of this "Rapid Excavation" effort has been the development of a means to apply the well-known virtues, both technical and economic, of the drill and blast method in a continuous process. The spiral blast concept, aimed at this specific goal, has been funded for initial studies (1) by the ARPA Rapid Excavation Program and, for the experimental work reported herein, by the Department of Transportation (2). The economy enjoyed by the drill and blast method stems from two factors: explosive energy is relatively cheap; and this energy is released so as to cause rock fragmentation largely through tensile failures. The relative ease and efficiency of tensile rock failures have long been recognized. The drill and blast process of course cannot be truly continuous since drilling and blasting (and other necessary functions) simply are separate, distinct operations. Although some surface explosive work has been done to avoid the need for drilled blast holes (3) it does appear that the high performance associated with explosive excavation requires placement of the explosive beneath the rock surface. This paper describes studies of blasting pattern which, in simplest terms, replaces the occasional heavy blast of conventional practice with frequent, much smaller blasts. The objective, of course, is to reduce the size of individual blasts

Jan 1, 1974

By N. S. P. Kumar

INTRODUCTION Development work at Carr Fork Mine of Anaconda Copper Company in Tooele, Utah commenced in August 1974. A decision to install an underground gyratory crusher for primary crushing run-of-mine ore and waste was made in 1976. Higher throughput rates, larger reduction ratios and greater flexibility in terms of meeting immediate and expanded production needs were the main reasons for selecting the gyratory crusher over the jaw crusher. UNDERGROUND MATERIALS HANDLING Underground crushing and conveying system was designed for a capacity of 16,300 mtpd of ore and waste on a 2-shift, 5-day week basis. Engineering and design of crusher complex was performed by Anaconda engineers at Carr Fork. Figure 1 represents the longitudinal section of mine showing the general materials handling system. Mine area is trackless except for materials and production haulage which is run on rail track on both 1200 and 970 levels. Ore from stopes and waste rock from development headings are handled by 3.8 cu m (5 cu yd) Jarco scoops and dumped into 2.4 m (8 ft) diameter ore and waste passes at the 1200 level. The material gravitates down to the 970 level where it is loaded into 12 cu m (420 cu ft) ASEA mine cars using side loading chutes. The muck train, consisting of 15 to 18 cars and two 27 mt General Electric trolley locomotives, is hauled over a distance of 2,300 m (7,550 ft) to

Jan 1, 1981

By Thomas de Lange

Extensive test work performed on the Coalscan 3500 ash analyzer at the Grootegeluk Coal Mine has led to the successful implementation of on-line ash monitoring to control the quality of coking coal and power station coal. Test work results are given and the advantages of on-line bias compensation discussed. Some details of the quality control systems subsequently implemented are also highlighted. Finally, the economic benefit of on-line ash monitoring based on the Mayer curve is demonstrated.

Jan 1, 1992

By J. Pflieger

The International Iron and Steel Institute (IISI - http://www.worldsteel.org) has initiated the development of a comprehensive freely-available, internet-delivered package of highly interactive e-learning resources for undergraduate students and steel industry employees. The resulting e-learning environment (http://www.steeluniversity.org) creates a ?one-stop? shop covering all aspects of steelmaking, steel products and applications, the underlying scientific and engineering principles, industrial and academic collaboration, as well as environmental and sustainability issues relevant to the steel industry. The module entitled ?Sustainability, Steel and the Environment? of the steeluniversity.org provides interactive e-learning resources on the following topics - Sustainability. - Principles of Life Cycle Thinking. - Environmental Life Cycle Assessment. - Application of Life Cycle Assessment. The aim of this particular module is to enable the learner to identify relevant environmental parameters over the life cycle of steel products as well as to learn about the resulting environmental effects and impacts. Furthermore he/she will be enabled to explain the basic idea of Life Cycle Thinking and Life Cycle Assessment (LCA) in terms of Goal and Scope definition, System Modelling, Life Cycle Inventory (LCI), Life Cycle Impact Assessment (LCIA) and Interpretation. In addition, the learner can explore selected LCA scenarios facing the steel industry and its customers in the automotive and construction sectors.

Jan 1, 2007

By J. W. Leonard

Breakage, handling and treatment techniques that result in the placement of greater quantities of coal in fixed volume haulage units such as ships, railroad cars, trucks, mine cars, shuttle cars and scoops can do much to increase productivity by improving bulk density to reduce delivered cost, surprisingly enough, only in steel industry by-product coking has this subject been investigated and applied to practice, where as much as 20% or more productivity has been achieved. Research at UK Mining using popular coal mine loading cycle simulators shows that for typical Central Appalachian mining conditions a 10 to 20 percent gain in bulk density can produce a 15 to 30 percent increase in the loading cycle time of fixed volume shuttle-car/scoop based mining systems.

Jan 1, 1989