Search Documents

By D. Grgic, A. Giraud, F. Homand

RESUME : Le comportement mécanique partiellement saturé du minerai de fer a été étudié à partir d’essais de compression simple sur des éprouvettes à pression capillaire imposée par les solutions salines. Les échantillons restent peu saturés (32 %) même pour une humidité relative de 94 %, du fait de la présence de mésopores. Jusqu’à 90 % d’humidité relative la résistance diminue régulièrement. De 90 % à 94 % une forte chute est observée et pourrait être liée à la fois aux effets capillaires et à l’hydratation de certains minéraux. Le cycle hydrique subit par la roche dans la mine a été modélisé en 1D à l’aide d’un code de calcul entièrement couplé pour les milieux poreux partiellement saturés. Les calculs ont montré notamment une diminution importante en paroi des contraintes totales au cours de la phase de désaturation et une augmentation importante au cours de la phase de resaturation. Ces variations pourraient induire un endommagement du massif et être à l’origine d’instabilités, et soulignent l’intérêt d’une modélisation avec une géométrie plus adaptée. MOTS-CLEFS : mines de fer, partiellement saturé, pression capillaire, résistance, modélisation. ABSTRACT : The partially saturated mechanical behavior of iron ore has been studied from uniaxial compression tests on samples in which the suction is imposed with aqueous solutions. Samples are little saturated (32 %) even for a 94 % relative humidity because pores are too large. Up to 90 % relative humidity the strength decreases regularly. From 90 % to 94 % a great decrease is observed ; it could be explained by the capillary effects and the moisturizing of some minerals. The hydrous cycle imposed to the rocks in the mine has been modeled with an 1D fully coupled code for partially saturated porous media. The computations have shown an important decrease in the total stresses at the wall during the desaturation stage and an important increase during the re-saturation stage. These variations could induce a rock mass damage and instabilities, and highlight the necessity of a modeling with a well-adapted geometry. KEY-WORDS : iron mines, partially saturated, suction, strength, modeling. ZUSAMMENFASSUNG : Das mechanische Verhalten von teilweise gesättigten Eisenerz wird durch einachsige Druckversuche untergesucht. Die Prüfkörper haben einen durch Salzlösungen gestimmten kapillarischen Druck. Sie bleiben kaum gesättigt (32 %), sogar bei einer relativen Feuchtigkeit von 94 %, aufgrund der Anwesenheit von Mesoporen. Bis eine relative Feuchtigkeit von 90 % verringert sich gleichmässig die Druckfestigkeit und zwischen 90 % und 94 % merkt man eine starke Abnahme in Verbindung, möglicherweise, mit kapillarischen Effekten und Hydratation von bestimmten Mineralen. Die nümerische 1D Modellisierung des gezwungenen Wasserzyklus im Stein der Mine ist mit einem für porösen Medien ganz vernetzten Rechnungcode geführt. Sie zeigt besonders ein bedeutendes Sinken der Gesamtspannung während der Entwässerung und eine bedeutende Steigerung während der Sättigung. Diese Veränderungen könnten die Beschädigung des Gesteines herbeiführen und die Grundlage von Unstabilität sein. Sie unterstreichen die Wichtigkeit eine Modellisierung mit einer gut geeigneten Geometrie. STICHWÖRTER : Eisenminen, teilweise gesättigt, kapillarischer Druck, Druckfestigkeit, Modellisierung.

Jan 1, 2003

By R. W. O. Kersten, J. D. Austin

A questionnaire was circulated in 1986 that had the objective of establishing the type of material that members would like to see featured in the Journal of The South African Institute of Mining and Metallurgy. The questionnaire contained five main questions involving the following:

Jan 1, 1987

A diverse selection of rockbolt designs and resin anchors are available for use in underground mines. Research in recent years at the UNSW Mining Research Centre led to the construction of a rockbolt pull-testing facility. This facility has subsequently been upgraded, commissioned and initial test work has been completed to verify the pull-test process. A test program has been completed with the objective to understand the load transfer mechanism and improve the general performance of rockbolts. This paper describes the results of this research. Une sélection diverse de dessins du rockbolt et ancres de la résine est disponible pour usage dans les mines de métro. Faites des recherches ces dernières années à l'UNSW que le Centre de la Recherche Minier a mené à la construction d'une facilité de l'essai de la traction du rockbolt. Cette facilité a été améliorée par la suite, le travail de l'épreuve en commission et initial a été complété pour vérifier le processus de la traction-épreuve. Un programme de l'épreuve a été complété avec l'objectif comprendre le mécanisme du transfert de la charge et améliorer la performance générale de rockbolts. Ce papier décrit les résultats de cette recherche. Eine verschiedenartige Auswahl an rockbolt-Designs und Harzankern ist dafür verfügbar, benutzen Sie in unterirdischen Bergwerken. Forschung in letzten Jahren beim UNSW-Bergbau Forschung Zentrum führte Ruckerprobung-Einrichtung zur Konstruktion eines rockbolt. Diese Einrichtung ist anschließend befördert worden, ist beauftragt worden und wird abgezeichnet, prüfen Sie, die Arbeit ist vervollständigt worden, um den Ruckprüfung-Prozeß zu verifizieren. Ein Prüfungsprogramm ist mit dem Objektiv vervollständigt worden, den Lastübertragungsmechanismus zu verstehen und die allgemeine Aufführung von rockbolts zu verbessern. Dieses Papier beschreibt die Ergebnisse dieser Forschung.

Jan 1, 2003

By R. Romano

Some topics, which difficult the effective use of RMR for dam foundations, are reviewed and a new geomechanics classification system, DMR (Dam Mass Rating), is proposed -as an adaptation of RMR- giving guidelines for several practical aspects in dam engineering and appraisal of dam foundation. On revise quelques problems qui ont fait difficile l’application du RMR pour les fondations des barrages. On propose un nouveau classification système, DMR (Dam Mass Rating)-comme un désarroi du RMR-qui donne recommendations pour quelques problèmes pratiques dans le projet et construction des barrages, et de ses fondations. Es werden einige die praxisgerechte Nutzung des RMR (Rock mass Rating) erschwerende Themen betrachtet und ein neues Geomechanisches Einteilungssystem, das DMR (Dam Mass Rating), eine Anpassung des RMR, vorgeschlagen. Daraus resultieren neue Richtlinien für verschiedene praktische Aspekte beim Dammbau und bei der Beurteilung von Dammunterbauten

Jan 1, 2003

The use of a time series variogram as an aid in controlling the quality of a product was pioneered by Pierre M. Gy and is described. The ability to analyse and interpret covariance relationships time series data is possible using the variogram. The concept of stream heterogeneity allows sources of variability in process streams to be identified and isolated. Principally this is distributional heterogeneity that is due to a short range effect of segregation in the process stream related to size or composition distribution of the material on a local scale and due to a long-range change in the size and grade of the material stream. The variogram is simply a tool for representing these sources of variability in a way that is explicit, allowing identification of the source and providing important insights to temporal continuity between samples. This paper describes the chronologically related large-scale variability in an iron ore process stream (%Fe), and illustrates the control and mitigation of variability at various stages within the process using a variogram. Three main sources of variability are identified including the random variability V[0], the process variability V[1], and the variability due to cyclical phenomena V[cyclic], arising from human routine or mechanical defects. These sources of variability can be represented on the control chart that provides the plant superintendent with insights as to the sampling capability of the systems in place. Maintaining levels of variability within customer specification limits requires that production systems be controlled without overcorrecting for the trends in changing quality. This can be done only by representing the limits of control relative to the limits of specification on a control chart. Where the specification limits encroach on the control limits, one or the other, or both, may need to be changed; specification limits that constrain the control limits lead to reactive decision making that is expensive and stressful for plant operators.

Jan 1, 2008

By M. Le Roux

Fine coal (-500 µm) is notoriously difficult to dewater. It is not uncommon for a dewatered product to have a moisture content as high as 30 per cent after vacuum filtration. This poses several handling and financial problems to such an extent that a lot of fine coal is discarded onto slurry waste ponds. A novel way of dewatering fine coal was developed at North-West University. It entails deliberately damaging the filter cake during dewatering to allow for an increased flow of air through the cake at the expense of the applied pressure differential. This method resulted in an average improvement in final cake moisture of between 3 per cent and 5 percent when executed in the laboratory under controlled conditions. A device was designed that could be fitted onto existing belt filters that would damage the filter cake as it passes by. This device was tested on a vacuum belt filter installation at a coal beneficiation operation in the Waterberg coal field in South Africa. The results showed a 3 per cent reduction in final moisture of the cake, proving the validity of the method at full industrial scale.

Jan 1, 2012

By M. Le Roux

Fine coal (-500 µm) is notoriously difficult to dewater. It is not uncommon for a dewatered product to have a moisture content as high as 30 per cent after vacuum filtration. This poses several handling and financial problems to such an extent that a lot of fine coal is discarded onto slurry waste ponds. A novel way of dewatering fine coal was developed at North-West University. It entails deliberately damaging the filter cake during dewatering to allow for an increased flow of air through the cake at the expense of the applied pressure differential. This method resulted in an average improvement in final cake moisture of between 3 per cent and 5 percent when executed in the laboratory under controlled conditions. A device was designed that could be fitted onto existing belt filters that would damage the filter cake as it passes by. This device was tested on a vacuum belt filter installation at a coal beneficiation operation in the Waterberg coal field in South Africa. The results showed a 3 per cent reduction in final moisture of the cake, proving the validity of the method at full industrial scale.

Jan 1, 2012

The annual general meeting of the Branch was held at the St. Helena Club on Thursday, August 21, 1969. Mr J. G. Kirchner (Chairman) was in the Chair. Also present were Mr R. C. J. Goode, President of the S.A. Institute of Mining and Metallurgy; Nine Members: Messrs N. A. Honnet, W. R. Lawrie, J. N. Saunders, D. D. Waterman (Committee Members), M. G. Cullen, G. C. P. Labuschagne, H. A. G. Slater, I. G. Thomas, T. Zadkin and Nine Associate Members: Messrs R. Campbell, D. E. Couperthwaite, T. M. Espach, J. M. Ferguson, G. W. Futcher, A. G. C. Merson, E. R. Penny, R. B. Sutherland, J. W. van den Munckhof and One Visitor: Mr D. J. McLaren. The Chairman declared the meeting open and, on behalf of the Branch, thanked the President for coming from Johannesburg to attend. MINUTES OF THE PREVIOUSGENERALMEETING As the Minutes of the General Meeting held on June 18, 1969 had not yet been published in the Journal, the Chairman moved that their adoption and the discussion thereof be deferred to the next General Meeting. This motion was adopted unanimously. CHAIRMAN'S ANNUAL REPORT 1968/69 At Mr Kirchner's request, Mr. R. C. J. Goode took the Chair during the presentation of the Chairman's Annual Report. (This report was published in the August 1969 issue of the Journal.) OFFICE BEARERS AND COMMITTEE MEMBERS FOR THE YEAR 1969/70 The Chairman announced that the outgoing Committee had elected the following office bearers for the coming year: Chairman: N. A. Honnet; Vice-Chairman: J. N. Saunders; Immediate Past Chairman: J. G. Kirchner. The Chairman then read a letter from the scrutineers reporting that the following had been elected to the Committee: M. S. Grobler, W. R. Lawrie, L. O. W. Leimer, A. T. Lewis, R. S. Pearson, T. Zadkin. The Chairman thanked the scrutineers for their services, and congratulated Messrs Lawrie, Leimer and Zadkin on their re-election and Messrs Grobler, Lewis and Pearson on their election to the Committee. The Chairman announced that he had heard, with regret, that Mr. T. Zadkin would be leaving the O.F.S. at the end of August, 1969. Mr Zadkin had served on the Committee continuously since the inception of the O.F.S. Branch and records showed that he had only failed to attend three General Meetings in over nine years. The Chairman expressed the gratitude of the Branch for Mr Zadkin's invaluable services to the Institute, congratulated him on his well earned promotion and wished him well in his new position. INDUCTION OF CHAIRMAN The Chairman introduced Mr N. A. Honnet to the meeting by briefly outlining his past career and, after congratulating him on his election, called upon him to take the Chair. In congratulating the out-going Chairman on a very successful term of office, Mr Honnet said that due to the absence of many Committee Members for a large portion of the year Mr Kirchner had carried a heavy burden, and he moved a vote of thanks and appreciation for Mr Kirchner's efforts. This was carried unanimously. GENERAL BUSINESS There were no points raised under this heading. MINING AND METALLURGICAL CONGRESS The Chairman called on Mr W. R. Lawrie to give his talk on aspects of the Mining and Metallurgical Congress recently held in Britain. This presentation was illustrated with photographic slides and proved of great interest to Members. Mr D. D. Waterman proposed a vote of thanks to Mr Lawrie and the Chairman then asked Mr R. C. J. Goode to contribute to Mr Lawrie's address. Mr Goode thanked Mr Kirchner for his efforts during his very successful term of office and congratulated the in-coming Chairman and Vice-Chairman on their election. He then gave a brief talk on aspects of the Congress not dealt with in Mr Lawrie's address. These included the industry's requirements of graduates, the necessity of their rapid advancement and the desirability of sending such young men to attend future Congresses. Mr Goode announced that two symposiums will be sponsored by the Institute next year, one on Tunnelling and the other on Open Cast Workings.

Mr G H Park was born and brought up in Zimbabwe, in mining from the University of the Witwatersrand. Starting as a Learner Official at Rand Mines, he went Mr D J van Niekerk was educated at Helpmekaar Boys' High School in Johannesburg and the University of Pretoria. Mr C J C Janse van Vuuren was educated at Klerksdorp High School, Pretoria Technical Colege, the University of Pretoria, and Unisa. He holds the folowing degrees: BSc (I&S), BSc Hons (Met Pta), ND (Met Tech), AEP (Unisa). Prof. R F Sandenbergh was educated at the Afrikaanse Hoerskool Germiston and the University of Pretoria. He holds the degrees of B Ing (Chem), M Ing (Chem), and D Ing (Metal). President's Award Professor Jannie van Deventer, Head of the Department of Metalurgical Engineering at the University of Stelenbosch, has been honoured with one of the five President's Awards for 1990. These awards are made by the CSIR's Foundation for Research Development. G R Bozzoli Awards* Prof. Alan Kemp, Dean of the Faculty of Engineering at the University of the Witwatersrand, has appealed to industry not to cut bursary funding during recessionary times.

Jan 1, 1990

By V. Coetzee

In 1992, a paper was compiled highlighting a common-sense approach to electric smelting at Impala Platinum. Since then, the smelter complex has undergone considerable changes. Mineral economics, UG2 exploitation, and changing environmental legislation have enforced numerous process upgrades, yet a common-sense approach has always been adopted. This document details the major changes in the smelter complex at Mineral Processes (Minpro) over the past 15 years, and provides the rationale for the changes. Keywords: Pyrometallurgy, furnace, PGM, platinum, nickel, copper, electric smelting, six-in-line, Peirce-Smith, Impala Platinum.

Jan 1, 2006

By J. T. Jordaan

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree This paper addresses the critical parameters that need to be considered when designing a mechanized bord-and-pillar mining layout for a narrow tabular steep dipping orebody. These parameters are : ?Reef dip ?Reef width ?Geological structures within the orebody ?Physical dimensions of the selection of machines ?Gradeability of the selection of machines. The main objective in designing such a layout is to maximize machine efficiencies whilst minimizing dilution. This methodology was then applied in the design of a mechanized bord-and-pillar mining layout for a given piece of ground (Vlakpoort and Moddergat) using a given selection of machines. This piece of ground contains the PGM bearing UG2 Reef with an average thickness of 124 cm and dipping at 18°withadverse strike and dip changes. Two bord-and-pillar layouts were designed for this area. Layout 1 is characterized by the use of strike conveyors to convey ore on strike with an average LHD hauling distance of 35 m. Layout2 uses LHDs for all on strike conveyance of ore with an average hauling distance of 75 m. These two layouts were then technically and financially compared. It was concluded that layout 1 is theoretically superior but layout 2 was chosen due to its greater flexibility and probability of operational success. Layout 2 was also compared to conventional mining and it was concluded to be more economically feasible. However the latter is a proven mining method in these conditions and has a lower risk operational failure. Bord-and-pillar mining has some favourable promises such as improving labour difficulties, lowering operating costs and providing safer working conditions. The success of mechanized bord-and-pillar mining in narrow tabular steep dipping orebodies will depend on the extent of the research and development efforts which need to create and innovate technologies to overcome some of the current limitations stated in the above-mentioned parameters.

Jan 1, 2003

By G. J. van Tonder

The use of Molecular Recognition Technology (MRT), a highly selective separation technology using specifically designed ligands (such as macrocycles), has been demonstrated to be an effective treatment process for removal of several ions that are commonly found in many hydrometallurgical circuits as well as in environ-mental treatment operations. Ions removed by MRT include base, heavy and transition metals, precious metals, halides, and alkali/alkaline earths. A MRT pilot plant run was conducted at Zincor to demonstrate the cobalt/nickel purification of zinc electrolyte, and to recover saleable pure cobalt/nickel sulphate solution. The MRT process holds various advantages, which include the elimination of a catalyst such as arsenic trioxide, conventionally used in cobalt and nickel cementation. SuperLig® 138 can be used to remove cobalt and nickel from120?170 g/l Zn-solutions at pH 1?2. The Zincor MRT application demonstrated its capability of concentrating large volumes o copper barren impure solution at low cobalt and nickel concentration levels in the feed, to small solution volumes at high cobalt and nickel concentrations. Around 99.5% of the cobalt was removed from solution with cobalt impurity levels in feed varying between 10 mg/l and 26 mg/l.

Jan 1, 2002

By N. Ragoonanthun

Paper written on project work carried out in partial fulfilment of B.Sc. (Mining Engineering) degree This report investigates the optimization of a raiseline in order to open up the ore reserve quicker. The project was carried out at Mponeng Mine (an Anglogold shaft formerly known as Western Deep Levels 1 Shaft and South Mine, in Carletonville). The project was divided into two focus areas namely: ?To design an optimum layout of a raiseline, which includes the scheduling of all activities for the establishment of the infrastructure. Consideration was given to the blasting practice, mining cycle, orepass placement and slusher positioning. Two designs were carried out on the above basis. ?The design of a ledging operation/practice to match the optimized layout of the raiseline. The ledging cycle design involved a thorough investigation into the possible use of drill rigs, Electronic Delay Detonators (EDD) blasting technology, longer drilled holes, Threshold Blasting (THROB),and water jet cleaning.

Jan 1, 2003

By D Reddy

Rosh Pinah Zinc Corporation is a zinc-lead mine located in southern of Namibia. It is currently considering the development of a low grade ore body containing about 2.8% zinc. This ore can be utilised by the concentrator if it could be upgraded prior to the ball mill. Preliminary work indicated that the ore may be upgraded in a pre-beneficiating stage by using dense medium separation, X-ray sorting or a combination thereof to a feed grade of minimum 9% zinc. This paper describes the process followed in evaluating the technologies for pre-beneficiation. The results from test work indicated that the low grade ore is amenable to pre-beneficiation by both dense medium separation and X-ray sorting. A comparison between the two technologies showed that dense medium separation marginally outperformed X-ray sorting on grade and recovery. The results for the X-ray sorting were achieved by tuning the calibration curve specifically for the samples tested.

Jan 1, 2008

By W. Robert, J. Wirth, G. Grasselli

ABSTRACT: Strength, deformability and fluid flow properties of rock joints are to a great extent controlled by the surface roughness. The hydraulic conductivity of a rock fracture depends on the aperture distribution, the surface roughness and the contact area, each of which depend on the stresses that act on the fracture plane. However, despite much recent work, a complete understanding of the relationship between void space geometry, contact areas, applied stress, and hydraulic conductivity has yet to be achieved. Moreover, although in situ rock joints are subjected to both normal and shear loading, few studies have been conducted to investigate the effect of shear displacements on fluid flow through a single rock fracture, and which have addressed the issue of flow anisotropy induced by shearing. Experimental flow tests show that with increasing shear displacement, the fracture becomes heterogeneous and anisotropic, and becomes more permeable in the direction parallel to the displacement (Yeo et al., 1998). On the other hand, dry shear tests show that the surface fails in areas facing the shear direction (Grasselli and Egger, 2003). Moreover, the experimental results confirm that the shear strength of rock joints is direction-dependent. In this paper, a three-dimensional morphological description of several a natural fractures that have undergone shear displacement were generated using the Automated Topographic System at the University of Basel. The data analysis method of Grasselli (Grasselli et al., 2002a) is used to determine the surface parameters that are known to control the shear strength. Simulations of fluid flow through this fracture, in various directions relative to the direction of shear, are conducted using an FEM flow simulator. The results constitute the most detailed analysis yet undertaken of the relationship between shear displacement, shear strength, and fracture transmissivity. RESUME: La rugosité des joints en roche joue un rôle primaire sur la réponse hydromécanique du massif fracturé. En effet, la conductivité hydraulique des discontinuités en roche est influencée par la rugosité, et par la distribution des ouvertures et des zones de contact, dont chacun dépend de l’effort normal et du cisaillement qui agissent sur la surface du joint. Les essais d'écoulement en laboratoire montrent que si cisaillée, la fracture devient anisotrope, et plus perméable dans la direction parallèle au déplacement (Yeo et al., 1998). D'autre part, les essais de cisaillement indiquent que seules les zones de la surface qui font face à la direction de cisaillement sont impliquées dans le cisaillement (Grasselli et Egger, 2003). D'ailleurs, les résultats expérimentaux confirment que la résistance au cisaillement des joints de roche est dépendante de la direction. Dans cet article, plusieurs fractures en roche ont été analysées en utilisant un système de mesure topographique à l'Université de Bâle. La méthode d'analyse de données proposée par Grasselli (Grasselli et al., 2002a) a été employée pour calculer les paramètres de la surface qui déterminent la résistance au cisaillement. Plusieurs simulations du coulage, dans diverses directions relativement à la direction du cisaillement, ont été faites à l’aide d’un programme de calcul à éléments finis. Les résultats constituent une des analyses les plus détaillé sur le rapport entre le déplacement pendant le cisaillement, la résistance au cisaillement, et la transmissivité spécifique de la fracture. ZUSAMMENFASSUMG: Die Festigkeit, Verformbarkeit und Hydromechanik von geklüftetem Fels wird hauptsächlich von der Oberflächenrauhigkeit der Bruchflächen bestimmt. Die hydraulische Leitfähigkeit einer Kluft hängt von der Verteilung der Rissbreiten, der Oberflächenrauhigkeit und den Kontaktflächen ab, die ihrerseits von dem auf die Bruchfläche wirkenden Druck beeinflusst werden. Obgleich in letzter Zeit viel in dieser Richtung geforscht wurde, kann der Zusammenhang zwischen Porenraumgeometrie, Kontaktflächen, wirkendem Druck und hydraulischer Leitfähigkeit noch nicht vollständig erklärt werden. Obwohl Klüfte in situ sowohl Normal- als auch Schubspannungen ausgesetzt sind, wurde der Einfluss von Scherverschiebungen auf den Kluftwasserfluss und die daraus resultierende Fliessanisotropie in einer einzelnen Kluft bisher kaum untersucht. Experimentelle Untersuchungen des Durchflusses zeigen, dass die Kluft für größer werdende Scherverschiebungen heterogen und anisotrop wird wobei die Permeabilität parallel zur Verschiebungsrichtung ansteigt (Yeo et al., 1998). Andererseits zeigen trockene Scherversuche, dass die Oberfläche an Stellen versagt, die gegen die Verschiebungsrichtung anstehen (Grasselli und Egger, 2003). Des weiteren bestätigen die experimentellen Ergebnisse eine Richtungsabhängigkeit der Kluftscherfestigkeit. In diesem Artikel wird eine dreidimensionale morphologische Beschreibung mehrerer natürlicher, durch Scherspannungen verschobener Klüfte vorgestellt, die vom Automated Topographic System der Universität von Basel erstellt wurde. Das von Grasselli (Grasselli et al., 2002a) entwickelte Datenanalyseverfahren wird zur Feststellung der die Scherfestigkeit bestimmenden Oberflächenparameter herangezogen. Mittels einer FEM-Simulation wird der Durchfluss durch eine solche Kluft in verschiedenen Richtungen simuliert. Die Ergebnisse stellen die bisher ausführlichste Analyse des Zusammenhangs zwischen Scherverschiebung, Scherfestigkeit und Durchlässigkeit (Transmissivität) einer Kluft dar.

Jan 1, 2003

By H. Ogasawara

Information on rock stress is important for safe mining in seismically active ground. On a major gold mine, a few tens of crews are continuously conducting geological drilling with small pneumatic machines. However, stress measurements are not often carried out in South African deep-level gold mines. One of the reasons is the drilling diameter that overcoring requires, which is much larger than the diameters used in regular geological drilling, e.g. Boart Longyear Metre Eater, which drills A[O] or B[O] holes. Larger diameter holes result in slower drilling advance, more load in transportation and handling at sites, and higher cost. In order to enable overcoring in BX size (60 mm diameter), we modified the compact conical-ended borehole overcoring (CCBO) technique that has been suggested by International Society for Rock Mechanics (ISRM) and was originally designed for NX drilling (76 mm diameter). With a single overcoring, the 3-D stress tensor can be determined. We tested this modified method at a depth of about 3 km at Moab Khotsong mine in South Africa. We worked with drilling crew who usually work at geological drilling with the Metre Eater. In January 2011, we tried using regular geological drilling tools (a sequence of a normal BX bit, reamer, and rod) without success. In August and September 2011, introducing stabilizers and thin BX bits, we succeeded. We could complete a cycle of procedures necessary for an overcoring, including shaping the borehole-end conically, glueing a 16-element strain cell, and overcoring, within 2.5 hours. Only 10 cm overcoring is needed, which increases the chance of successful overcoring in heavily fractured conditions. This modified method is suitable for up-dip holes to depths of 10-15 m from tunnels, and has the potential to be widely used at the initial stage of geological exploration drilling at many localities.

Jan 1, 2012

By D. Nag, J. Fernando

Hazelwood Power Mine is one of the largest open pit brown coal mines in Australia. The removal of overburden is the first step in coal winning operation. The primary aim of construction of overburden dump is to provide an effective stable working surface for stacker. The paper discusses site investigation techniques used to determine dump soil properties, stability analysis method using GALENA and GWEDGEM, results of stability analysis. The paper concludes with recommendation for a safe dumping strategy for level 2 stacker dumping.

Jan 1, 2003

By Frank Johnson

Between 2000 and 2006, platinum production from the South African mines expanded from 206 to 307 tonnes (DME, 2007). Most of this additional metal has come from traditional ?narrow? reef stoping, generally taken to mean stoping in working places with a mining height of less than 1,5 metres. It is well known that narrow-reef stoping presents safety, technological and ergonometric challenges (Pickering, 2007). In planning for the expansion, which is still continuing, the platinum mining industry realized that it could not simply continue with traditional methods of narrow-reef mining. Particular issues identified were: ? High labour-intensivity: caused by use of hand-held rock drilling machines, labour-intensive support installation and stope cleaning; ? Dependence on rock-drillers: this occupation is no longer an attractive one and there is a reducing flow of new recruits; ? Safety: most of the work is performed close to the new faces, where there is the greatest exposure to the hazards of falling rock.

Jan 1, 2008

By E. Munnik

The Chambishi Metals Cobalt Plant in Zambia has recently installed a novel oxidation/precipitation pressure leach process as part of the COSAC (CObalt from Slag And Copper as by-product) Project. Aniron-cobalt-copper alloy, produced by the carbothermic reduction of slag, is atomized and pumped to the COSAC Leach Plant, where cobalt and copper are recovered as dissolved sulphate salts, andiron is rejected primarily as hematite. Cobalt and copper are subsequently recovered as cathode metal in the existing Chambish ioperation by conventional electrowinning. This paper examines the challenges faced during the design and subsequent successful commissioning of the COSAC Leach Plant. The challenges discussed include alloy handling, autoclave design, autoclave cooler design, residue liquor recovery and the water balance design. Keywords: Chambishi, Avmin, COSAC, Zambia, Copperbelt, cobalt, copper, alloy handling, pressure leach, autoclaves, cooling, filtration.

Jan 1, 2003

By I. Hague

Support liners for underground applications include steel and timber sets, meshing and lacing, screen/mesh, shotcrete and thin support liners (superskins). Over the past few years, major advances have been made in the design and application of liners; especially shotcrete and thin support liners. For shotcrete in mines these advances include the common use of slick-lines to solve logistics problems, the design of alkali free accelerators, the use of synthetic fibres and the new generation application equipment. The field of thin support liners is a new one but advances have been dramatic. This paper discusses the progress made and the need for standardization in definitions and testing for thin support liners. It concludes that the newer technologies have a huge potential positive impact on the industries, from both safety and cost points of view. Le chemisage de soutènement pour extraction souterraine comprend des cadres d’acier ou de boisage, mailles et chapeau, cribles/mailles, béton projeté et des chemisages minces de soutènement (super-peaux). Dans les dernières années, des progrès considérables ont été fait dans la conception et application des chemisages, en particulier les chemisages de soutènement en béton projeté et les chemisages minces. Pour le béton projeté dans les mines, ces progrès comprennent l’utilisation courante de lignes de minerais broyés fin pour résoudre des problèmes de logistique, la création d’accélérateurs sans alcali, l’usage de fibres synthétiques et d’une nouvelle génération d’outillage. Le domaine des chemisages minces de soutènement est très récent mais les progrès ont été rapides. Cette étude présente les progrès accomplis et discute du besoin de standardisation dans les définitions et les tests pour chemisages minces de soutènement. La conclusion est que les technologies nouvelles présentent un énorme impact potentiel positif sur les industries, du point de vue à la fois de la sécurité et de la rentabilité. Unterstützungsverkleidungen für Untertaganwendungen inkludieren Flecht und Seilwerk, Gitter/Geflecht, Spritzbeton und dünne Unterstützungsverkleidungen (superskins). Während der letzten Jahre wurden grosse Fortschritte im Design und in der Anwendung der Verkleidungen gemacht; besonders bei Spritzbeton und dünnen Unterstützungsverkleidungen. In Bezug auf Spritzbeton in den Gruben schließen diese Fortschritte den allgemeinen Gebrauch von Rutschbahnen ein um Logistikprobleme zu lösen, das Design von alkalifreien Akzeleratoren, den Gebrauch von synthetischen Fasern und die neue Generation von Anwendungsausrüstung. Der Bereich der dünnen Unterstützungsverkleidungen ist neu, aber die Fortschritte sind drastisch gewesen. Diese Arbeit behandelt den erzielten Fortschritt, die Notwendigkeit der Normierung in den Definitionen und in der Prüfung dünner Unterstützungsverkleidungen. Sie kommt zum Schluß, daß die neueren Technologien, sowohl vom Gesichtspunkt der Sicherheit als auch der Kosten, eine sehr große potentielle positive Auswirkung auf die Industrien haben.

Jan 1, 2003