Search Documents

By M. F. Wells

The method used to salvage South Deep?s Main Shaft after it was flooded by an inrush of water at about 450 m below collar on 1 May1996 is described. The individual techniques employed in the salvage were all proven technology, but the combination in which they were applied is considered to be novel. The operation involved the following activities in order of occurrence. ?the dewatering of the shaft with submersible pumps ?the placement of a French drain on the shaft bottom muck pile ?the positioning of large diameter heavy walled draft tubes, and smaller tightening up, grout intrusion and reverse flow pipes ?the casting and curing of a structural concrete plug; the capping of the draft tubes; the intrusion of several thousand tons of cement grout into the aquifer by pressure induced reverse flow ?the sealing of the aquifer ?extensive probe drilling and sealing of the zone around the inrush point with cement and other specialized grouts ?the mining out of the plug and the re-establishment of normal sinking routines.

Jan 1, 1999

By C. Righi, R. Carli

In modern steel continuous casting technologies mould fluxes are well-known to assure lubrication required by tribological system of mould-solidifying strand shell, and to provide crystalline phase solid film, contributing to control heat extraction between strand and mould wall. Actual cooling rates during normal continuous casting mould operations are far higher than critical cooling rate of the liquid slag. Indeed, DTA measurements point out that even relatively small cooling rates of 30?50 K/min are high enough to give exiguous formation of crystals. In this paper, contribution of devitrification in defining crystalline phase formation of industrial basic mould slag, used in continuous casting of crack-sensitive steel grades, has been investigated by means of non-isothermal experiments study. Devitrification has proved to play a major role in mould flux crystallization in a working environment explaining the higher amount of crystalline phase formed in plant sample in comparison with lab sample from DTA analysis with typical cooling rate of 5?20 K/min. The amount of crystalline phases formed ranks as follow: Cuspidine > Combeite > Gehlenite. Kinetic analysis of DTA non-isothermal experiments has provided kinetic parameters through Kissinger and Ozawa methods, as Avrami constant resulting to be n ?2 and activation energy of Cuspidine crystallization resulting to be EC= 315 kJ/mole. The effect of addition to the parent material of oxides as MnO, TiO2, ZrO2, Al2O3 and Fe2O3near to saturation point has proved to affect, in certain cases, crystallization behaviour of mold flux. In particular, MnO, TiO2, ZrO2oxides produce a relevant dump of crystallization of Combeite and Gehlenite phases, while Al2O3and Fe2O3do not appreciably affect crystallization. Key words: Mould flux, crystallization, devetrification, DTA non-isothermal analysis, Kissinger and Ozawa methods.

Jan 1, 2004

We present a novel hybrid algorithm for quantifying the ore grade variability that has central importance in ore reserve estimation. The proposed algorithm has three stages: (1) fuzzy clustering, (2) similarity measure, and (3) grade estimation. The method first considers data clustering, and then uses the clustering information for quantifying the ore grades by means of a cumulative point semimadogram function. The method provides a measure of similarity and gives an indication of the regional heterogeneity. In addition, grade estimations can be obtained at different levels of similarity using a weighting function, which is the standard regional dependence function (SRDF). Keywords: Grade, fuzzy clustering, similarity measure, point madogram, weighting function.

Jan 1, 2008

By C. S. Chenga

Sustainable development is currently an extremely relevant concept worldwide, especially in developing countries like South Africa. Mining and metals companies are also directly affected by the sustainable development agenda. The Mining Charter?s requirements as well as new legislation (Mineral and Petroleum Resources Development Act) expect, among others, for mines to support infrastructure and poverty eradication projects in the communities surrounding the mines. The aim of this paper is to, against the background of a qualitative study of mining communities in the North-West Province of South Africa, put forward some critical factors for the sustainability of social development projects in the mining sector.

Jan 1, 2006

A comprehensive review of ore pass records, from ten Quebec underground mines, indicated some of the limitations of available design tools to predict the occurrence of ore pass interlocking hang-ups in metal mines. The Distinct Element Method was used to perform a series of numerical experiments in order to investigate the influence of ore pass geometry, rock fragments shape and size distribution on material flow in an ore pass. Guidelines have been developed to help limit the occurrence of interlocking hang-ups in an ore pass. The proposed guidelines were evaluated with respect to field observations. Ein kompletter Bericht der Erzrollezeichnungen, von 10 Quebec unterirdischen Gruben, hat einige der Beschränkungen der vorhandenen Designwerkzeuge angezeigt, um das Auftreten Erzrolle der blockierenhang-ups in den Metallgruben genau vorauszusagen. Eine Reihe numerische Experimente mit der eindeutigen Element-Methode, wurden aufgenommen, um den Einfluss von Erzrollegeometrie, Partikelform nachzuforschen und Felsenkorngrößenverteilungen auf Materialfluss in ein Erz überschreiten. Dieses hat zu die Entwicklung der Richtlinien geführt deren Implementierung das Auftreten der blockierenhang-ups in eine Erzrolle begrenzen sollte. Die vorgeschlagenen Richtlinien wurden in Bezug auf Labor- und Feldbeobachtungen ausgewertet. Une revue de la performance actuelle des cheminées à minerai dans 10 mines souterraines du Québec a indiqué les limites des outils de conception servant à dimensionner les cheminées pour minimiser le nombre d’accrochages par enchevêtrement rocheux. Des séries de modélisations numériques, utilisant la méthode des éléments distincts, ont été réalisées afin d’évaluer l’influence de la géométrie des cheminées, de la forme des fragments rocheux et de la distribution granulométrique sur l’écoulement du matériel dans les cheminées. Cet exercice a permis de développer des lignes directrices pour le dimensionnement des cheminées afin de limiter l’occurrence d’accrochage par enchevêtrement rocheux. Les lignes directrices proposées ont été évaluées en fonction des observations effectuées sur le terrain.

Jan 1, 2003

By R. J. Pine, J. M. Rance, J. S. Coggan

ABSTRACT: The safe design of excavations created in a fractured rock mass is of paramount importance in rock engineering. Depending on the nature of the stress regime acting on an excavation, and the associated deformational behaviour of the rock mass surrounding the excavation, a number of potential failure mechanisms exist. These involve a combination of shear failure on existing joints, extension of critically oriented joints and propagation of new fractures through previously intact rock. Conventional numerical codes usually adopt either a continuum or discontinuum approach; this often results in significant over simplification and kinematic limitations particularly when modelling complex rock mass behaviour in the close vicinity of excavations. This paper describes the results from several case examples using a combined finite element-discrete element code, ELFEN that incorporates a crack propagation mode. Through the use of selected rock engineering examples, the authors demonstrate the potential of the code in the realistic simulation of complex rock failure both in underground and surface excavation applications. RÉSUMÉ: La conception sûre des excavations créées dans une masse de roche fracturée est d'importance primordiale dans la géotechnique. Selon la nature du régime d'effort autour d’une excavation, et le déformation associé de la masse de roche autour de l'excavation, il exsite un certain nombre de mécanismes potentiels d'échec. Ceux-ci comportent une combinaison d'échec de cisaillement sur les joints existants, la prolongation des joints d’orientation critique et la propagation de nouvelles ruptures dans la roche précédemment intacte. Les codes numériques conventionnels adoptent habituellement l’approche, soit d’un continuum, soit de discontinuum; ceci a souvent comme conséquence une sursimplification significative et les limitations cinématiques en particulier en modelant le comportement complexe de la masse de roche très proche des excavations. Cet article décrit les résultats de plusieurs exemples de cas en utilisant un code qui s’agit d’une combination d’élément discret et d'élément fini, ELFEN qui incorpore un mode de propagation de fissure. Par l'utilisation des exemples choisis géotechniques, les auteurs démontrent le potentiel du code dans la simulation réaliste de l'échec complexe de roche pour les applications aux excavations soit au fond soit à l’extérieure. ZUSAMMENFASSUNG: Das sichere Design der Aushöhlungen, die in einer zerbrochenen Felsenmasse verursacht werden, ist vom paramount Wert in der Felsentechnik. Abhängig von der Natur des Druckregimes, das auf einer Aushöhlung und dem dazugehörigen deformationalen Verhalten der Felsenmasse umgibt die Aushöhlung fungiert, bestehen eine Anzahl von möglichen Ausfalleinheiten. Diese beziehen eine Kombination des Scherausfalls auf vorhandenen Verbindungen, Verlängerung der kritisch orientierten Verbindungen und Ausbreitung der neuen Brüche durch vorher intakten Felsen. Herkömmliche numerische Codes nehmen normalerweise entweder ein kontinuum oder discontinuum Annäherung an; dieses ergibt häufig bedeutende Übervereinfachung und kinematische Beschränkungen, besonders wenn es kompliziertes Felsenmasseverhalten in der Nähe der Aushöhlungen modelliert. Dieses Papier beschreibt die Resultate von einigen Fallbeispielen mit einem kombinierten begrenzten Element - getrennten Elementcode, ELFEN, das einen Sprungausbreitungmodus enthält. Durch den Gebrauch von vorgewählten Felsentechnikbeispielen, demonstrieren die Autoren das Potential des Codes in der realistischen Simulation des komplizierten Felsenausfalls bei Anwendungen für beide Tagebaue und Untergrundsaushöhlungen.

Jan 1, 2003

By A. W. Diedericks

Rosh Pinah Zinc Corporation (RPZC) identified implementing a Mineral Resource Management (MRM) programme at the mine as a strategic incentive. The purpose of the programme is to optimize the economic value of the RPZC mineral resource, over the total value chain of the mine, taking expected macro economic conditions into consideration as well. With Mineral Resource Management still being a relatively young drive in the mining industry, information on the concept is relatively scarce. RPZC had several successes and problems with implementing such a concept and also still has a way to go before a complete Minerals Resource Management approach is implemented at the mine and entrenched as a working culture. The purpose of this paper is to: ?define a systems approach to implementing a Mineral Resource Management programme at a base metal mine ?indicate the specific MRM approaches taken at RPZC ?indicate the expected advantages of implementing a MRM approach ?measure the actions already taken against the systematic MRM approach, and indicate the advantages already captured ?indicate the way forward taking lessons learned into consideration ?indicate proposals to implement the MRM approach in the macro mining environment in South Africa.

Jan 1, 2003

By S. V. Rungan

Since 1994, South Africa has been the subject of international attention, especially in regard to its transformation initiatives, which aim to redress the post-apartheid imbalances. Mining, as a major employer and one of the major industries in South Africa, has been the focus of the government?s Black Economic Empowerment initiative with the introduction of the Minerals and Petroleum Resources Development Act and the Broad?Based Socio?Economic Empowerment Charter for the South African Mining Industry. The historical background to South Africa?s transformation and the role of the mining industry are pivotal to an appreciation of certain aspects of the Minerals and Petroleum Resources Development Act and the Broad?Based Socio?Economic Empowerment Charter for the South African Mining Industry. The issues around Black Economic Empowerment and the enabling of a smooth transition to the South African mining industry of the future are explored in this paper.

Jan 1, 2005

By Simon St J Tose

The objective of this paper and presentation is to review the different criteria and methodology used by AEL and other organisations to create a pre-split design which delivers a stable highwall for the life of that part of the mining operation. It will look at the need to adapt and change the way, size and direction of the production blasts as the mining phase approaches the highwall position for which a pre-split has been created. Key Words: Pre-split: Design; Highwall; Perimeter

Jan 1, 2006

By Michelle Mouton, Johanna van Deventer, Jussi Vaarno

Mintek has been involved in numerous projects to remove Fe and Mn from dilute Co sulphate solutions by means of oxidative precipitation using air/SO2. Test work was done using a gas induction system, designed and supplied by Outotec. Various aspects, such as SO2 concentration, SO2 flowrate, impeller rotation speed and pH were investigated on a 2 m3 scale. Batch tests were performed using a residence time of 5 hours. Mintek has been involved in numerous projects to remove Fe and Mn from dilute Co sulphate solutions by means of oxidative precipitation using air/SO2. Test work was done using a gas induction system, designed and supplied by Outotec. Various aspects, such as SO2 concentration, SO2 flowrate, impeller rotation speed and pH were investigated on a 2 m3 scale. Batch tests were performed using a residence time of 5 hours. Impeller rotation speeds of 0-220 rpm were tested, and it seemed that speeds of between 80 and 220 rpm gave similar Fe and Mn removal rates. Co and Cu losses were generally below 1% and 5% respectively at pH 3.

Jan 1, 2007

By R. M. Spang

Abstract Between the German city of Dresden and the Czech capital Prague a 4-lane highway is under con-struction. At the outskirts of Dresden it will cross the narrow and deeply eroded Weißeritz Valley by a bridge. Two twin tube tunnels under oblique angles join the bridge out of the rocky valley flanks. The different geotechnical conditions of these 4 tunnel portals, their design and construction are described within this publication. The two southern portals of the tunnel Dölzschen are situated within a vertical 65 m high former quarry slope, 25 m above the valley floor. The slope proved instable due to toppling failure and exposed serious rockfall risks. Systematic anchoring, scaling, rock bolting, netting and filling under extreme access conditions eliminated these risks. Tunnel excavation started from the slope surface without any pre-cut or conventional portal construction. The opposite northern portals of the tunnel Coschütz are situated in more gentle rock slopes. After removal of debris, excavation of the eastern tunnel started in a 30° slope striking oblique to the driving direction, without any precut, too. Because of the gentle slope inclination the cross section was not earlier completely covered by rock than 30 m behind. The western tunnel started from an optimized short, narrow and steep precut. Its flanks were stabilized by reinforced shotcrete and rock bolts. Because of the small distance between the tubes rock bolts were drilled into the cross section of the neighboring tunnel. Tunnel excavation was made by drill and blast operation, preliminary support consisted of steel arches, reinforced shotcrete and radial rock bolts. Thorough survey of the bolt’s coordinates and direction prevented them from meeting each other. Rock bolts were of the permanent type to prevent the final lining from being obliquely loaded. Systematically arrayed measuring devices checked deformations of slopes and tunnels. Zusammenfassung Der Neubau der Bundesautobahn A 17 wird Dresden und Prag miteinander verbinden. Die vierspurige Autobahn quert westlich von Dresden das enge und tief eingeschnittene Tal der Wilden Weißeritz mit einer Brücke. An beide Brückenwiderlager schließen mit schiefwinkligem Anschnitt doppelröhrige Tunnel an, deren Portale in den felsigen Talflanken liegen. Die unterschiedlichen geotechnischen Verhältnisse, die Überlegungen für einen jeweils optimalen Entwurf und der Bau der portalnahen bergmännischen Tunnelabschnitte sind Gegenstand dieser Veröffentlichung. Die Südportale des Tunnels Dölzschen liegen in einer vertikalen, 65 m hohen Felswand, 25 m über dem Talgrund. Die Felswand erwies sich als global kippgefährdet, außerdem lagen flächig verteilte erhebliche Steinschlag- und Felssturzrisiken für Bau und Betrieb vor. Die Kippgefahr wurde durch ein Systemraster aus vorgespannten Felsankern, die Steinschlag- und Felssturzrisiken durch bergsteigerisches Beräumen mit dem Brecheisen, Felsnägel und Steinschlagschutznetze eliminiert. Der Tunnelausbruch begann von einer Vorschüttung direkt in der Felswand ohne Voreinschnitt im Schutz einer kurzen Luftbogenstrecke. Die gegenüberliegenden Nordportale des Tunnels Coschütz befinden sich in wesentlich flacheren Hängen. Nach dem Aushub einer mehrere Meter dicken Abraumhalde begann der Tunnelausbruch der östlichen Röhre asymmetrisch mit einer Luftbogenstrecke in einer spitzwinklig zur Vortriebsrichtung streichenden, 30° mit dem Vortrieb steigenden Felsfläche, ebenfalls ohne Voreinschnitt. Wegen der flachen Neigung der Böschung war der Tunnelquerschnitt erst nach 30 m vollständig überdeckt. Für den Vortrieb der westlichen Tunnelröhre mussten erst eine zwischen den Röhren vorhandene Felsnase teilweise abgetragen, die westlich anschließende zurückspringende Felswand vertikal gestellt und gesichert und Felsaushub in der rechten Flanke getätigt werden. Der damit entstehende Voreinschnitt wurde so kurz wie möglich und ohne seitliche Arbeitsräume ausgeführt. Die Sicherung der Böschungen erfolgte mit bewehrtem Spritzbeton und Felsnägeln. Wegen des geringen Abstands der beiden Röhren wurden die unteren Lagen der radialen Ausbruchsicherung durchgeankert. Der Tunnelvortrieb begann im Schutz eines geankerten Portalkranzes und ebenfalls von einer Luftbogenstrecke aus.

Jan 1, 2003

By O. I. Ostrovski, D. K. Belashchenko

The aim of this paper is the construction of models of systems with ionic and ionic-covalent bonds (molten salts) using experimental diffraction data and the calculation of their structure and thermodynamic and transport properties. Modelling was performed using algorithm BELION, in which the non-coulomb part of interaction potential between ions in the model was determined by the method of iterative simulation which targeted agreement between calculated and experimental partial pair correlation functions (PPCFs). The ionic charges in salts, which can be fractional, were determined by minimization of internal energy. In this paper, the algorithm BELION is applied for chlorides of alkaline-earth metals. Pair potentials, PPCFs, atomization energies, self-diffusion coefficients and electric conductivity are calculated. The charge of alkaline-earth metals was in the range of 2.0-2.1, slightly increasing from Mg to Ba. Partial pair correlation functions and atomization energies of models agree well with experimental data for MgCl2, SrCl2and BaCl2. Keywords: molten salt, molecular dynamics, partial pair correlation function, ionic charge, atomization energy, diffusion.

Jan 1, 2004

By S. E. Olsen, K. Tang

Slag-metal and slag-metal-gas heterogeneous equilibria involving MnO-containing slags have been simulated using recently developed Mn-based alloy and IRSID oxide thermochemical databases. A large number of experimental equilibrium data have been used to verify the calculation results. The experimental slag-metal and slag-metal-gas equilibria in MnO-SiO2binary, MnO-SiO2-CaO and MnO-SiO2-Al2O3ternary, MnO-SiO2-CaO-Al2O3quaternary andMnO-SiO2-CaO-Al2O3-MgO higher-order system can be reproduced within experimental uncertainties. The influence of temperature, CO partial pressure and slag chemistry on the Mn-and Si-distribution equilibria have been quantitatively evaluated. This leads to a sound basis for optimizing the manganese ferroalloy production processes. Key words: MnO-containing slag, manganese ferroalloy, equilibrium simulation, thermochemical database

Jan 1, 2004

By A. Kondratiev

A structurally-based viscosity model for fully liquid silicate slags has been developed and applied to the Al2O3-CaO-‘FeO’-SiO2system at metallic iron saturation. The model links the slag viscosity to the internal structure of melts through second nearest neighbour bonds concentrations taken from the quasi-chemical thermodynamic model. This viscosity model describes experimental data over the whole temperature and composition ranges within the Al2O3-CaO-‘FeO’-SiO2system at metallic iron saturation and can now be applied to other industrial slag systems.

Jan 1, 2004

By A. Beitz, P. Smartt, G. Einicke, G. Rowan, P. Glynn

Coal is Australia’s highest export earner and Australia is the world’s largest exporter of coal. With coal now being extracted from deeper reserves under increased risk profile, and in the interest of aiding the stability of coal supplies, Japan is funding a number of safety projects in Australia and China. The CSIRO, Australia’s premiere research organisation with the country’s largest exploration and mining research group, are currently undertaking a jointly funded Japan-Australia safety project at Anglo Coal’s new Grasstree Colliery in central Queensland. The project, entitled Mine Communication and Information for Real-time Risk Analysis, will deliver step-change capabilities in data integration, decision support, gas monitoring, geo-technical monitoring, emergency response and personnel safety to the Grasstree Colliery. Some key activities include: developing and installing underground coal mine Ethernet LAN components, real-time monitoring of gas and geo-technical sensors, MODBUS serial to TCP/IP converters, e-reporting of underground conditions, emergency guidance systems and underground trials of Internet Protocol telephone and video. The project seeks to integrate (in real time) key data sets from the comprehensive and diversified range of propriety system currently in use at mines (ventilation, strata, operations e.g. haulage, pumps, conveyors etc) into a single integrated risk management interface. This interface will filter the data through a rules-based inference engine that will cross reference the various data streams, compare with past events and outcomes associated with the similar historical data and present this “intelligence” to

Jan 1, 2003

By M. Verri

[ ]

Jan 1, 2009

The current methodology to design stope support systems in South African gold and platinum mines is based upon the tributary area concept. The discontinuous nature of the hangingwall rock is not adequately addressed, and mechanisms leading to rock mass failures between adjacent support units are poorly understood. The work reported here aims to formulate a basis for quantifying support mechanisms and gain insights into the influence of rock discontinuities on stable hangingwall spans. Numerical models are used to qualitatively investigate the stress transfer from the support units to the discontinuous hangingwall. Stable hangingwall spans are quantified by considering two failure mechanisms, namely (i) beam buckling, and (ii) shear failure due to slip at the abutments. The output of the proposed design methodology is appropriate site specific support spacing, based on discontinuity spacing and orientation. The method is particularly suited to mines at intermediate and great depth, where typically the hangingwall is highly discontinuous due to face parallel mining induced fractures. Results of parametric studies show that with increasing in situ compressive hangingwall stress, beam thickness and friction angle, hangingwall stability is increased, leading to wider stable hangingwall spans between adjacent support units.

Jan 1, 2000

By A. F. Lee

A pick-up apparatus capable of yielding quantitative results has been described. Studies of some collector-mineral systems have been presented to illustrate the versatility of the apparatus and prove the validity of results.

By J. J. Bezuidenhout

The waste-heat boiler is used within the Sulphide flash smelting process as the main dust and energy recovery unit. The large volume of off-gas discharged from the flash smelter is at a very high temperature (1350°C) and contains a significant dust load that subjects the downstream waste-heat boiler to tough and demanding conditions. The boiler cavity is especially prone to dust accretions, fouling, and corrosion caused by accumulation of molten particles and precipitation of sulphuric acid. Computational fluid dynamics (CFD) is applied within a qualitative study to model the flow and heat transfer distribution throughout the waste-heat boiler. The commercial CFD package, Fluent 6.2.16, was applied to a modified waste-heat boiler (23 m ×11 m ×5.4 m) within the Outokumpu flash smelting process. This investigation focuses on the geometric modifications to the typical boiler design, which includes elevation of the ceiling, placement of flow-obstructing baffles and radiation plates parallel within the flow path. Also investigated were various boiler operating conditions such as the circulation of process off-gas, air leakage from the dust discharging hoppers and variation in inlet gas composition. The geometric modifications had the desired effect of increasing the volumetric utilization and therefore enhancing heat transfer between the boiler surface and the gas stream and dust segregation. Introducing circulated off-gas at a rate of 20 m/s and at a 45° angle to the front of the waste boiler further enhanced cooling while reducing the high impact of the furnace-uptake gas-stream on the boiler ceiling. The placement of radiation plates was found to be very effective in enhancing the heat transfer surface and distributing gas flow within the boiler. These results present recommendations towards an improved waste-heat boiler design. Keywords: flash smelting, waste-heat boiler, CFD simulation, off-gas cooling.

Jan 1, 2008

By J. M. Font, R. G. Reddy

Jan 1, 2004