Search Documents

A description is given of a simple, cheap device that enables the intact shear strength of rock to be determined quickly and inexpensively. Thin rock plates, prepared with a diamond saw, are tested in double shear by a linear punching action. By varying the direction of the diamond-saw cut in a number of specimens, the change in shear strength can be measured for different orientations relative to the rock fabric.

Jan 1, 1980

By P. A. Laxen, P. J. van Staden

Alternative procedures for the recovery of gold from old sand dumps are discussed, with emphasis on the use of heap leaching. The modification of material to improve its permeability prior to heap leaching is not currently receiving much attention in South Africa. The channeling of solutions through heaps and the high consumption of reagents sometimes ascribed to heap leaching can, as shown by the results described in this paper, be lessened by desliming of the sand prior to heap leaching and the treatment of the resulting slimes fraction by agitation leaching and carbon-in-pulp. This combined procedure results in a higher overal recovery of gold. Alternatively, the sand can be heap-leached as it is after agglomeration with lime and cement, which improves the mixing and neutralization of the material, as well as lessening the probability of channeling.

Jan 1, 1988

By F. L. D. Cloete

he above article by E. Barnea, which appeared in the January 1978 issue of the Journal (vol. 78, no. 6, pp. 143-145), calls for comment in view of the author's claims for the novelty of his proof. He states in his article that its main purpose is to give a mathematically acceptable proof by induction of the 'recently proposed' equation

Jan 1, 1978

By A. J. Van Rensburg, N. B. Strydom, C. H. Van Graan

The design, construction, and use of a practical ice-jacket for miners by N. B. STRYDOM, Ph.D. (Illinois) (Fellow), D. MITCHELL, Ph.D. (Rand) (Member), A. J. VAN RENSBURG, M.Sc (Poteh) (Visitor), and C. H. VAN GRAAN, M.Sc (Pretoria) (Visitor) Microclimate suits have been shown to be very effective in decreasing physiological strain in hot, wet environments, thus enabling men to work without risk in areas that would normally carry a high risk of heat stroke. In this paper, some design considerations in the development of the frozen jacket are described. Water complied with most of the desirable properties required of a coolant material for use In a microclimate suit. The Human Sciences Laboratory has developed a jacket in which ice is used as the coolant and which is designed according to the most acceptable anthropometrical characteristics. The jacket consists of an inner poncho-type waistcoat containing 28 water compartments. Over this is worn an insulating jacket, which minimizes warming of the coolant by the environment. Suitable refrigeration units have been developed to freeze the jackets underground. Laboratory tests have shown that these jackets are effective for about 2,5 hours, Irrespective of the wet-bulb environment, when men are working at a moderate rate. Jackets should, however, be used only in environments in which the wet-bulb temperature is in the range of 32,S0 to 35,S °C.

Jan 9, 1974

By F. Q. P. Leiding

SYNOPSIS A technique is described for measuring the change in volume in a borehole drilled in a rock mass subjected to stress and strain. It is shown that the volumetric strain or change in volume provides a practical estimate of the the stress in the rock.

By A. M. Thyer

Throughout the history of mining, underground fires or explosions have killed many hundreds or thousands of people. Fortunately, the safety record has gradually improved as a result of many people’s work on improving safety standards and work practices. However, fire and explosion still remains a threat in many situations. As a result the UK Mines Inspectorate commissioned a project to study materials used underground and to develop a fire/explosion risk assessment system. Such a system has been developed, following the study of incidents, specified fire resistance criteria, and fire safety practices. The final methodology uses a series of check sheets to identify potential fuels and ignition sources, preventative measures, fire/explosion mitigation systems, and items for inclusion in emergency plans.

Jan 1, 2003

By A. García-Gutiérrez, A. Aragón-Jerónimo, R. Salazar-Mendoza

A theoretical analysis of a two-region solid-liquid flow system in horizontal pipes is presented, which considers a stationary bed of drill cuttings as a porous medium (-region) below of a two-phase dispersed flow (-region).The method of volume averaging was applied in this study to derive a rigorous mathematical model in which each variable is precisely defined. This model includes the volume-averaged transport equations for both the two-phase dispersed flow and the porous medium regions and terms from a macroscopic forces balance. The solution of the two-region model allowed evaluation of the behaviour of pressure gradient as a function of velocity, total volume fraction of cuttings and the relationship of the height of the stationary bed and pipe diameter. The solution is based on a backward finite difference explicit scheme. The simulated physical system is a pipe of 4.135 m in horizontal length and 0.0508 m in diameter. A one-dimensional, mesh-centred grid, consisting of 100 nodes, is used. The numerical results were compared with experimental data on slurry flows and a good agreement was found. Keywords: two-phase, cuttings transport, solid-liquid flow, drilling modelling, volume averaging.

Jan 1, 2007

By R. G. Votteler, A. C. Brent

"The first in this series of two papers, on the potential of renewable electricity sources for mining operations in South Africa, investigated the internal structure of mining corporations to evaluate feasible alternative electricity sources that were identified as through earlier research. The purpose of this paper is to combine current knowledge about the external macroeconomic and the internal environments to produce a clear picture of how renewable sources of electricity could perform from the perspective of mining corporations in South Africa. The multi-attribute value theory (MAVT) approach was adapted to structure the research and results. The model was fed with real-time data provided from five different energy companies and four mining corporations operating in South Africa. The results show that the performance of hybrid versions of the currently used electricity sources (diesel generators and Eskom grid connection) with solar PV and onshore wind is favourable compared with the current sources alone. The advantage of diesel generators is significantly greater than that of the Eskom grid connection. By combining the macroeconomic influences with the MAVT results, hybrid solar PV versions are identified as having the greatest potential. In second place are hybrid wind solutions, which have the shortcoming that good wind conditions occur only in coastal regions where there are fewer mining activities. Geothermal hybrid versions are the least favourable owing to the lack of service infrastructure and high initial investment costs.IntroductionRecent developments in the macroeconomic environment necessitate an investigation of the internal structure of mining corporations to evaluate possible alternative electricitygenerating sources (Roehrl and Riahi, 2000). To be able to combine current knowledge of macroeconomic factors and the internal structure of mining corporations, the research process is presented in two papers. The first paper (Votteler and Brent, 2016) investigated the internal structure and argued that a strategic tool should be used to evaluate electricity sources from the perspective of mining corporations. The multi-criteria decision analysis (MCDA) approach was selected as the most appropriate strategic tool. Based on a literature review of previous similar MCDA approaches in energy planning, it was concluded that no adaptation of MCDA methods could be found from a corporate, mining, or South African perspective. Finally, the paper investigated the internal evaluation structure in collaboration with mining corporations, by identifying the criteria they use to evaluate electricity sources."

Jan 1, 2017

By P. S. Turner

After a brief account of the differences between the control of underground fires and those on the surface, the paper describes the analogue detection system used on the mines of the Anglo American Corporation of South Africa Limited. The system comprises Spanair gas analysers, Becon combustion-particle detectors, a telemetering system, a surface signal-recording and-processing system, and an alarm system. The use of the system is described and illustrated.

Jan 1, 1982

By J. E. Robinson, W. Pilkington, J. L. Taylor, B. J. Bluhm, E. B. Viljoen, P. Le Grange

The Chemwes uranium plant was designed and constructed within fifteen months; commissioning started during. June 1979, and the plant was producing at design capacity four months later. This account highlights the procedures and methods adopted to bring the plant Into production. The description of the various phases includes some details of the early evaluation, and the feasibility and optimization studies; of the financing, project management, design, construction, and commissioning of the plant; and of the training of personnel. Some of the mistakes made and the factors that contributed to the success are also listed.

Jan 1, 1981

By I. Zh. Bunin, M. V. Ryazantseva, V. A. Chanturiya

The paper proposes a new method for selective calciferous separation. The effect was achieved through the application of the combination of high-power electromagnetic pulses (HPEMP) and a specific reagent regime of the flotation. The combined application of HPEMP with the special reagent regime allowed for the improvement of the scheelite floatability: the recovery of CaWO4 rises from 41.2 % (untreated sample) to 58.5 (sample treated at 103 pulses). In contrast, the floatability of calcite decreases significantly: the recovery of calcite drops from 74.7% (untreated sample) to 41.1 % (sample treated at 103 pulses). The conditions were found for the selective separation of the minerals with very close flotation properties. Keywords: Calcite, scheelite, flotation, high-power electromagnetic pulses, DRIFT, XPS

Jan 1, 2020

By A. C. Wingrove

The paper outlines the selection of a dewatered tailings backfill system for the Johannesburg Consolidated Investment Gold Division, and covers the following aspects: (i) 16 Shaft pilot testwork; (ii) engineering design problems relating to the Cooke 3 Shaft backfill operation; (iii) in-line mixing - applications with respect to the Randfontein Estates Gold Mine and Western Areas Gold Mine backfill operations; and (iv) pipeline friction losses.

Jan 1, 1988

By J. D. Austin, D. G. Kringe

Rates of return realized on investments in the gold mines of the newer goldfields outside the Witwatersrand were calculated and analysed over various time intervals and on various bases. It is shown that these rates of return are strongly correlated with changes in the gold price and cannot be equated with the returns that are expected when investments are made, and that the changes in gold price also affect the rates of return on the Johannesburg Stock Exchange as a whole. These correlations are used, together with a limited application of the Capital Asset Pricing Model, to suggest the expected levels of threshold returns in real terms for new mining projects, for projects on existing mines, and for share valuations.

Jan 1, 1980

By Axel Schulze

HUGO PETERSEN has developed from the traditional firm of the same name that was established in 1906 in Berlin and is an engineering company specialising in general plant engineering now based in Wiesbaden. HUGO PETERSEN has many years wide-ranging experience in process plant engineering, primarily in the field of Sulphuric Acid Processes and Gas Cleaning. Together with its main shareholder, Chemieanlagenbau Chemnitz GmbH (CAC), a company with over 40 years experience in the international plant engineering business, HUGO PETERSEN implements turnkey new plants from initial consultancy right through to commissioning. In addition, HUGO PETERSEN can offer its clients improvements and revamps of existing plant systems. Initial consulting, planning and implementation take place within the context of a lean company organisation with experienced engineers and specialists. In all respects, many years of experience guarantee expertise over a wide range of possible applications For clients from the chemicals and metallurgical industries, as well as those in metals processing, HUGO PETERSEN GmbH?s breadth of experience means not just an efficient introduction to new methods and processes, but also their full implementation. In addition, along with design and construction for individual components, the company?s range of services also covers supply of complete plants, as well as modernisation projects and revamps in line with local conditions and existing quality requirements With own technologies and patents in the field of gas cleaning and sulphuric acid, supplemented by licences and cooperation projects, HUGO PETERSEN ensures expertise over a wide range of applications. With specialists and expert knowledge in these fields of application, HUGO PETERSEN is your partner of choice, supporting you and bringing your acid, and project to a successful conclusion.

Jan 1, 2009

By R. M. Mashishi, T. Malehase, O. J. Okonkwo

The concentrations of selected trace elements (As, Cd, Hg, and Pb in run-of-mine (ROM) coal, discard, and coal product were investigated to assess the efficiency of beneficiation in reducing trace element concentrations and ascertain any implications regarding environmental compliance to regulatory frameworks. Samples were collected from a colliery in Mpumalanga Province twice a month for a period of 24 months. The samples were ashed to approximately 0.21 mm, then digested in a mixture of 70% HNO3 and 40% HF and analysed using inductively coupled plasma-mass spectrometry (ICP-MS). Except for Pb, the mean concentration of all elements decreased from the ROM stage to the coal product stage. The order in which trace elements occurred from the highest to lowest throughout the production chain was Pb>As>Hg>Cd. With the exception of Cd, the mean trace element concentrations in the discard were above the total concentration threshold (TCT) set for landfill disposal. The As, Hg, and Cd concentrations in the product were well below the thresholds for all land uses. However, Pb concentrations in the product coal were above legal limits, which is of concern with regard to environmental compliance and the performance and marketability of the product.

Dec 13, 2023

By R. o. Cretier, L. A. Cisternas, A. López-Valdivieso, F. Valdes, E. Gálvez, G. Gahona

The size of the particle plays an important role in the flotation of minerals. Comminution allows the release of valuable species and their subsequent recovery. Then, the degree of concentration and recovery will depend on the size of the particle. In this work, we investigated the flotation of coarse particles (-850 +150 μm) of copper ores when using the fluidized-bed separator (HydroFloat® cell) and compared it with the process of conventional flotation with medium size particle (-150 μm) (Metso cell) using seawater. The collector concentration was the main variable studied in terms of copper recovery. The results show that the flotation of coarse particles is feasible using seawater without frother

Jan 1, 2020

By G. Raspa

The paper describes a computer procedure for evaluating and selecting recoverable reserves in a mine worked by sublevel stoping. The boundaries of the volume to be mined are optimally defined by means of the 3-dimensional Lerchs-Grossmann algorithm, separately applied to both sides of the panels. The procedure, which has been developed for Masua Mine (Sardinia), also provides for smoothing the optimized boundaries, positioning the drilling drifts, interactive design of drilling fans and calculation of tonnage and grade of each volley. These tonnages and grades form the input of another procedure evolved for production planning.

Jan 1, 1987

By J. S. Preston

The properties of some recently developed solvent-extraction reagents for the separation of cobalt and nickel sulphate solutions are reported. New commercial extractants based on alkyl phosphonic and alkyl phosphinic acids are described. These reagents show much improved selectivity for cobalt compared with established extractants. Some novel extractants developed at Mintek for the selective recovery of nickel in the presence of cobalt are also described. These reagents, which are based on mixtures of carboxylic acids and non-chelating oximes, are of interest in that no commercial nickel-selective reagents are currently available. Graphs showing metal loading and stripping, and pH-functionality, are presented. together with details of the metal separations achieved in batch countercurrent- extraction experiments with the various reagents.

Jan 1, 1983

By D. J. Adams, R. G. Gürtunca

In situ measurements and numerical modeling based on elastic theory showed that backfill stresses are considerably higher than originally thought. This has led to a change in understanding of rockmass behaviour. After describing previous work on the behaviour of the rockmass, this paper discusses possible reasons for the high stresses measured in backfil, and identifies the rockmass mechanisms possibly generating these stresses. It is concluded that the joints and the geological stratigraphy can lead to increased elastic convergence, and that the inelastic behaviour of the rockmass is also partly responsible for the increased closure measured in backfill. The use of an in situ modulus is suggested as an interim solution until a new computer model that allows for joints, different layers, and inelastic closures becomes available.

Jan 1, 1991

AFRICAN NATIONAL COMMITTEE ON TUNNELLING In 1970, the South African Institution of Civil Engineers, the South African Institute of Mining and Metallurgy, the South African Institute of Mechanical Engineers, and the Geological Society of South Africa held an international conference on tunnelling, known as Tuncon 1970. SUID-AFRIKAANSE NASIONALE TONNELBOUKOMITEE In 1970 het die Suid-Afrikaanse Instituut van Siviele Ingenieurs, die Suid-Afrikaanse Instituut vir Mynbou en Metallurgie, die Suid-Afrikaanse Instituut van Meganiese Ingenieurs en Die Geologiese Vereniging van Suid-Afrika 'n internasionale konferensie in verband met tonnelbou gehou, wat bekend gestaan het as Tonkon 1970.

Jan 5, 1974