Search Documents

By D. Yu, Y. Thibault, D. Paktunc

"Prereduction and flux-aided direct reduction of chromite provide significant advantages in reducing energy consumption and greenhouse gas emissions during ferrochrome production. In this investigation, a comparative evaluation of the influences of several alkali fluxes was carried out based on experimental observations supplemented by advanced material characterization and thermodynamic predictions. Direct reduction of a chromite ore with alkali fluxes at 1300°C for 1 hour produced (Cr,Fe)7C3 type alloys with Cr/Fe mass ratios from 0.7 to 2.3. Among the alkali fluxes, reduction aided by NaOH resulted in a high degree (85%) of Cr metallization with the ferrochrome alloy being Cr4.2–4.6Fe2.4–2.8C3. The formation of liquid slag, which facilitated Cr metallization, was limited by the formation of NaAlO2 between 800 and 1300°C. This, in turn, restricted the collection and transport of the charged ionic Cr species (i.e. O2–) to graphite particles. Under the conditions studied, ferrochrome particles were often small and largely unliberated, which would make the physical recovery of ferrochrome challenging. At 1400°C, the amount of liquid slag increased, enabling the growth of alloy particles. Direct reduction of chromite aided by NaOH is promising as an alternative technology to conventional flux-based smelting in electric arc furnaces. IntroductionConventional smelting processes are energyintensive (Riekkola-Vanhanen, 1999) with the energy requirements greater than 4 MWh/t (Naiker and Riley, 2006; Beukes, van Zyl, and Neizel, 2015), and the greenhouse gas emissions can be significant, exceeding 10.5 t CO2 per ton Cr in ferrochrome produced (International Chromium Development Association, 2016). These include emissions occurring on-site (smelter), emissions due to electricity production, and emissions due to upstream processes. Overall energy requirements are influenced by the degree of prereduction and smelter charge temperature. Significant reduction in electricity consumption can be realized if the charge is prereduced before feeding to the submerged arc furnace (Niayesh and Fletcher, 1986). This consideration has led to the development of several prereduction technologies, with the most important example being the Premus process. In comparison to the conventional smelting processes, this prereduction process lowers the overall energy consumption and greenhouse gas emissions by about one-third (Naiker, 2007)."

Dec 1, 2018

By E. Córdova, A. Anani, W. Nyaaba

Optimization of panels, haulage fleet, and waiting area involves deterministic and low-fidelity methods and experiential knowledge. The process is challenging because coal recovery and operational capabilities must be considered in the solution. The approach in this manuscript comprises the development of an integrated stochastic simulation model of a coal room-and-pillar system that addresses these challenges. The decision variables evaluated are panel width, number of shuttle cars, and change-out time (COT). The results show that the mine should implement the shortest possible COT, decreasing the cycle time and thereby increasing productivity and continuous miner (CM) utilization. The highest productivity and CM utilization for a fleet size of three shuttle cars is found in the 15-entry panel width. For the evaluated fleet sizes, the 19-entry panel width is optimal for the four and five shuttle cars. Among the three variables studied, panel width and fleet size had the most significant effects (5% increase) on the CM productivity, cycle time, and utilization.

Apr 2, 2022

By M. Onifade, O. S. Otuogbai, A. F. Mulaba-Bafubiandi, O. D. Eniowo, H. Grobler

Artisanal and small-scale miners in Nigeria struggle to attract formal financing to upgrade their operations to a more sustainable form of small-scale mining operation. Literature shows that for an investment to attract formal sources of financing; the business must be considered creditworthy by potential lenders. This means that the credit risks associated with the investment must be bearable for the potential lender. This study looks at how artisanal and small-scale miners can attract formal funding, which will help them take the leap from artisanal state to a form of sustainable small-scale mining operation. This study evaluates the creditworthiness of artisanal and small-scale mining operators using key credit risk parameters identified in the literature and through primary investigation. A quantitative study is conducted on a sample of 100 artisanal and small-scale miner establishments in Nigeria to evaluate the effect of these identified credit risk parameters on creditworthiness. It is shown in this study that being a member of a mining cooperative society, which is a form of social collateral, best improves the chances of access to formal financing for miners within the sample group. This underpins the role of social collateral, in both the formal and informal economy, and its influence in improving the creditworthiness of a typical artisanal and small-scale miner.

Jul 23, 2025

By T. Z. Sehume, J. R. Bunt, J. C. van Dyk, C. A. Strydom

"SynopsisCo-pyrolysis of four biomass samples (hardwood chip, softwood chip, pinewood chip, and sugarcane bagasse) with an inertinite-rich medium rank C South African coal was investigated. Proximate and ultimate analyses of the chars prepared using a heating rate of 10°C/min up to 1100°C in a nitrogen atmosphere were used to compare the properties of the biomass and the coal chars. Similar gross calorific values (28.5–29.1 MJ/kg) for the woody biomass-coal blended chars were observed, which were slightly higher than that of the coal char sample (26.5 MJ/kg). CO2 surface areas of the chars of the woody biomass samples (328.1–329.4 m2/g) and of the blends (238.5–271.5 m2/g) were higher than that of the coal char sample (94.2 m2/g). Thermogravimetric (TG), differential thermal analyses (DTG), and calculated weighted averaged TG curves indicated that the influence of the biomass on the pyrolysis rate of the coal is small and vice versa. The CO2-producing reactions of the coal were slightly enhanced during co-pyrolysis.IntroductionCoal utilization has led to rising concerns about adverse impacts on the environment (global warming) caused by toxic gases (H2S, SOx, NOx, and CO2) and remaining waste. Biomass is considered to be CO2-neutral with regard to the greenhouse gas balance, and is regarded as a renewable source that assists in reducing CO2 emissions when compared with coal (McGowan, 1991; McKendry, 2002). Biomass currently makes up approximately 14% of the world’s energy sources (McGowan, 1991; McKendry, 2002). Coal combustion and gasification are prominent processes in South Africa (in producing synthesis gas and energy) due to the abundance of coal in the country. Some of South Africa’s coal resources are, however, high in ash content and also are inertinite-rich, which renders them more difficult to use industrially than vitrinite-rich low-ash coal (Jeffrey, 2005; Strydom et al., 2011). There is a need to investigate the properties and behaviour of the inertinite-rich high-ash South African coals and especially their interaction with local biomass sources. The gasification process occurs through various stages, of which pyrolysis of the char residue forms an integral part (Bunt and Waanders, 2009). Currently, particular interest is shown in the co-utilization of coal and biomass to produce synthesis gas via the gasification process (Usón et al., 2010; McGowan, 1991; McKendry, 2002). Investigating the co-pyrolysis of the South African coal and local biomass material is thus the first step in evaluating the use of local biomass sources for co-gasification purposes."

Jan 1, 2015

By S. Combrink, N. Naude

Hydrocyclones are widely used in wet mineral classification applications and can be notoriously prone to wear. The methods currently used for quantifying hydrocyclone wear profiles are mostly twodimensional. In this paper it was attempted to quantify and monitor wear in three-dimensions, using a micro-CT scanner (Nikon XTH 225 ST). Hydrocyclone wear and, more specifically, spigot wear was investigated on a Multotec HC250 (Dc 250 mm, barrel diameter) hydrocyclone. The hydrocyclone is lined by a vulcanised natural rubber compound within a metal shell, with a thermosetting polyurethane spigot and vortex finder. Tests were conducted on the hydrocyclone in a pilot-scale recirculating test setup. The wear rate of the spigot was quantified by measuring the volume change within the spigot over 122 days in operation, using the micro-CT scanner. After 122 days in operation (recirculating feed materials) the wear in the hydrocyclone led to only a 13.67% loss of spigot volume. The relatively low wear rate could be related to the fact that material recirculation led to particle smoothing and a reduction in size, thereby decreasing the wear rate. This also shows the enormous influence that particle shape and size have on wear. The research was conducted with the support of Multotec, NECSA and the University of Pretoria. Keywords: Wear, hydrocyclone, micro-CT

Jan 1, 2020

By I. A. Mwamba

Titanium aluminide of composition Ti-47.5 at.% Al was prepared by melting titanium and aluminium of commercial purity with additions of precious metals of 0, 0.2, 1, 1.5 and 2 at.% content. The microstructure, hardness and oxidation properties were assessed. It was found that at 47.5 at.% Al, the microstructure of plain TiAl alloys was duplex, consisting of duplex lamellar grains and ? grains. The lamellar grains consisted of alternating lamellae of ? (TiAl) and a2 (Ti3Al), with overall aluminium content in the range of 43?47 at.%. The ? grains had a aluminium content above 50 at.%. The addition of precious metals to the TiAl alloy resulted in the formation of a new phase, with a high precious metal content, occurring mostly in the ? phase, without any major change to the microstructure. Increasing the amount of precious metals resulted in an increase of the new phase amount, at the expense of the ? phase. The hardness of the different alloys was around 300HV10. Overall, the research has shown that addition of precious metals to TiAl resulted in a slight increase in hardness and a significant improvement of the oxidation resistance. This shows that alloying TiAl with precious metals, at the addition levels investigated, does not alter the mechanical properties very much, but improves oxidation resistance.

Jan 1, 2012

By K. Dagdelen , S. K. A. Owusu

Uncertainty with regard to estimated grades and tonnages of a mineral deposit demands risk assessment in order to build investor confidence and attract the interest of other stakeholders in the success of a project. Uncertainties associated with Mineral Resource estimates can lead to unreliable production schedules and unpredictable cash flows. However, the techniques used in the mining industry to determine these uncertainties are inconsistent, because the important decisions taken in the process are solely dependent on the responsible Competent Person (CP), without limitations. This leads to disparities between different CPs’ results, using data-sets from the same drill-holes. The various standard codes for public disclosure provide guidelines and recommendations for the classification of Mineral Resources and Reserves but do not provide details on, for example, the amount of geological and geostatistical information needed to qualify for each category of Resources and Reserves. The parameters used to generate the classification categories are subjectively assumed by the responsible CP. In this paper we investigate the impacts of different CPs’ judgements on resource classification, using the same data-sets. The results underpin the need for the mining industry to develop a uniform Mineral Resources and Reserves classification framework that can minimize or avoid significant discrepancies that lead to potential misleading public disclosures.

Aug 8, 2024

By D. N. Golenkov, N. I. Lomaka, A. V. Kozub, T. V. Ignatova, E. V. Shelepov, D. O. Sharkovskiy, A. V. Chanturiya, R. I. Ismagilov

The modern Russian iron ore mining industry is faced with multiple challenges from everincreasing requirements of steel-making, the value of iron ore concentrates, depletion of high-grade ore reserves and complications of the mining and geologic environment’s necessity to process low-grade ores with complex material composition and low valuable mineral content; with finely disseminated aggregates of metal and non-metal minerals responding similarly to processing. The upgrade of the existing operations’ fine wet screening was implemented by Metalloinvest; as well as the design of a process flowsheet for concentration oxide ferruginous quartzites with low concentrating ability. The scientific basis for improvement of low grade ore concentrating efficiency and the upgrade of market product quality is supported by an in-depth study of ore characteristics, application of high performance equipment for separation of fine-grained mineral aggregates and use of depressor selective to ferruginous minerals in the flotation process. The benefits of wet fine screening have been proven by industrial scale tests; as well as the feasibility of significant upgrades in product quality which have been confirmed as a result of the tests. A road-map for the upgrade of an existing process for the concentration of unoxidised ferruginous quartzites deposited in the Mikhailovskoye ore field was developed, based on the industrial scale test of a fine screening process. With reference to the ability for concentration, three major ore types oxidised ferruginous quartzites were defined as a result of comprehensive geological mapping and process sampling: oxidised ferruginous quartzites with good concentrating ability: over Fe67% grade of concentrate with ca. 80% iron recovery; oxidised ferruginous quartzites with moderate concentrating ability: Fe65-67% grade of concentrate with 70-72% iron recovery oxidised ferruginous quartzites with low concentrating ability: below Fe60% grade of concentrate (cannot be processed into desired grade market product). A process flow diagram combining magnetic separation and flotation has been designed and recommended for implementation based on the in-depth research of defined Mikhailovskoye deposit iron oxide types, including grain size, chemistry, petrographic, mineralogy, hematite and magnetite grain size distribution and liberation analysis.

Jan 1, 2020

By L. Petzold

The demand for stainless steel is ever-increasing. As an essential element in stainless steel-making process, so is the demand of chromite concentrate. At the same time, the industry proven technologies for beneficiation of chromite are limited. Chromite is only crushed, screened and jigged to produce a concentrate. However, for ultrafine and low-grade material, no satisfactory beneficiation methods for the enrichment of chromite fines exist in industrial operation. This poses a clear challenge for the industry, which Primetals Technologies has addressed with the development of a new beneficiation process. The aim of this process was to enrich low grade chromite tailings to a quality suitable for the smelting process. Required concentrate grades are different over the world, concentrate grades of Cr2O3=40% and lower are found at the Bushveld Complex, South Africa. The target for the present study was a Cr2O3-grade in the area of 49%. Three different chromite tailings with Cr2O3 grades between 16 % and 29 % were part of a study, executed by Primetals Technologies. All three tailing materials were characterised by Mineral Liberation Analysis (MLA). Based on the physical, chemical and mineralogical findings, process flowsheets were developed. The process flowsheets included grinding to ensure a full liberation of the chromite. The liberated material was classified at a cut size of 63 μm to a coarse and fine fraction. Gravity separation and flotation processes were tested with the coarse particle fraction. Due to the limitations of gravity separation with fine particles, only the flotation process is suitable and was tested with the fine fraction < 63 μm. A Design of Experiment (DoE) with six factors, each three levels, was conducted to identify optimal parameters for the fine chromite flotation. Two different collectors were tested: a phosphoric acid ester and a fatty acid type collector. In small scale test work a chromite concentration suitable for the smelting process was achieved. On this basis Primetals Technologies will develop a pilot-scale test program to research recirculation effects and upscale potential of the process. Keywords: Mineral processing, tailings beneficiation, flotation, density separation, process development, chromite

Jan 1, 2020

By B. P. Watson, T. J. Maphosa, D. P. Roberts, L. J. Gardner

The results of FLAC3D modelling on chromitite Upper Group 2 Reef pillars from the Bushveld Complex of South Africa are described. The model input parameters were determined from laboratory triaxial tests with post-failure measurements. These geomechanical tests were performed on rock materials within the pillars and the immediate pillar foundations. In the models, postfailure behaviour was simulated using the concept of cohesion softening. Models were built to determine the strength and behaviour of pillars with a width-to-height ratio of approximately two. The original research aimed to find a suitable depth below the surface where Impala Platinum Ltd could safely introduce crush pillars; however, the paper only describes the model results: the ideal depth of the crush pillar introduction is not discussed. The results of the modelling are compared with the PlatMine formula for peak pillar strength and with an underground instrumented pillar located elsewhere on the same reef. Some insight into the effects of grid size on strength is also provided. Further underground measurements are recommended to verify the model results

Sep 9, 2024

By K. C. Sole, M. Makonese

Bushveld Belco is commissioning a plant for production of electrolyte used in vanadium redox flow batteries. Owing to the source material, the electrolyte is contaminated with Fe, at concentrations up to 140 mg/L, which negatively affects battery performance. This study examined the use of ion exchange to reduce the Fe concentration to the target value of < 100 mg/L from a feed solution containing 100 g/L V in 4 M H2SO4. Four resins with possible application were identified: Puromet MTS9570, Puromet MTX7010, Puromet MTS9500, and Puromet MTC1600H. Puromet MTS9570 outperformed the other three resins in all batch experiments with respect to loading capacity and selectivity over V, and was evaluated for Fe removal in fixed-bed column loading tests. Based on these data, preliminary sizing and design of a full-scale column was undertaken. Owing to the difficulty of eluting this resin, a philosophy of discarding the resin on loading to full capacity was considered. These data revealed that, despite the high selectivity of this resin for Fe over V, it would be too expensive and impractical to use this resin for full-scale operation under such conditions. It is recommended to remove iron earlier in the flowsheet prior to generation of the 4 M H2SO4 electrolyte.

Dec 11, 2024

By C. N. Eze, C. K. Ezeh, O. Nnabuife, N. M. Ugwoju, S. C. Enemuor, V. Okechukwu

In this study, the efficacy of Providencia vermicola KUBT-1 in the leaching and beneficiation of Agbaja iron ore was evaluated under varying conditions of temperature, ore particle size, and pH. Agbaja iron ore is a Nigerian low-grade ore containing about 43%–52% iron and a high amount of gangue materials, including phosphorus (1.4%–2.0%) and sulphur (0.12%). The study was organised in triplicate in shake flasks with 48 samples. One millilitre of washed cells of Providencia vermicola KUBT-1 suspended in normal saline at 0.5 McFarland standard (108 cells ml-1) was introduced into each flask containing 50 g of sterilised ore in 100 ml of bioleaching medium, and the samples incubated at room temperature for eight weeks. The levels of upgraded iron, mobilised sulphur, and phosphorus were determined by atomic absorption and ultraviolet spectrophotometric analyses, respectively. Results showed that a particle size of 0.8 mm was optimal for iron upgrading and sulphur mobilisation while 1.0 mm ore size was optimal for phosphorus mobilisation. Up to 89.60% of the iron was upgraded while phosphorus and sulphur were mobilised, leaving residual values of 0.223% and 0.02%, in the ore, respectively. The organism produced best beneficiation results at a pH of 2.5 and a temperature of 3ºC. Correlation analysis with the Pearson’s correlation model showed a positive correlation between iron upgrading and sulphur-phosphorus removal (r =1.000, and r =0.967), respectively. These results present Providencia vermicola KUBT-1 as a promising candidate for large scale leaching and beneficiation of Agbaja iron ore.

Dec 15, 2025

By C. R. Royal, B. E. Friedland

Energy & Densification Systems (EDS) has developed patented new technology crushing/milling equipment. The EDS Multishaft Mill is a compact vertical mill – utilising high-speed impacts to break down particles with large reduction ratios, low energy consumption and improved liberation. The milling action combines several processes to provide a multitude of output products to satisfy various specifications. Comminution often accounts for more than 60% of the total power consumption on a mine. Two of the key problems to be solved in comminution is to bring down the specific energy required to reduce particle sizes; and to improve liberation or improve the efficiency of the beneficiation and recovery of the required elements. The EDS Mill has shown extensive improvements in both these areas with energy efficiencies up to 75% better than conventional milling equipment and improving liberation beyond the standard beneficiation processes. Conventional comminution equipment requires massive, heavy parts to be moved or rotated, consuming a lot of energy in doing so and not inputting that energy into the breakage of particles. In the EDS Mill, ramping up the relatively small shafts to speed is all that is required. Once at speed, the momentum, together with the minimal amount of constant drive required, means that the energy can be transmitted directly and efficiently into breaking down the particles. The high-speed impacts allow for a shattering effect of the particles and this quickly generates a high ratio of fines. Furthermore, the single impact force breaks particles in a very different manner to conventional compressive force breakage. With compressive force breakage, the particle breaks from point to point. With high-speed impact force breakage, the force tends to migrate through the weakest areas of the particle, which tend to be the mineral boundaries. This, therefore, means that when the particles break, the various minerals are exposed and hence liberated. Keywords: Comminution, high-speed impact, liberation, energy efficiency, novel comminution

Jan 1, 2020

By R. Rumpold

The platinum group metals (PGMs) palladium, platinum, and rhodium represent the key materials for automotive exhaust gas treatment. Since there are currently no adequate alternatives, the importance of these metals for the automotive industry is steadily rising. The high value of PGMs in spent catalysts justifies their recycling. The state-of the-art technology is to melt the ceramic carrier and collect the precious fraction in a liquid metal bath. As the feed material has quite high melting points, huge amounts of energy are required for this process. Hydrometallurgical treatments of the spent catalysts offer the possibility to recycle the PGMs with less energy and time demands. Moreover, automotive catalysts contain further valuable materials to improve the exhaust gas treatment. These compounds, like cerium oxide, cannot be recovered in pyrometallurgical processes. This paper deals with a special process that uses hydrometallurgical principles to recycle the valuable metal fraction from spent automotive catalytic converters. Hydrochloric acid in combination with hydrogen peroxide is used as leaching agent. This combination selectively dissolves the PGMs and the cerium, which can be recovered in separate steps. As the leaching solution is regenerated and reused, wastewater generation is minimized. Furthermore, the process residues constitute potential byproducts.

Jan 1, 2012

By R. Kuyvenhoven, A. Parbhakar-Fox, X. Prieto, J. Quevedo, L. V. Danyushevsky

This paper presents the results of a study focussed on determining the distribution of cobalt in different types of pyrite of the La Estrella IOCG deposit in Chile. In the IOCG mineral deposits, where copper is the main product, the quantification and distribution of cobalt is required to correctly define the technical and economic viability of recovering cobalt as a by-product. In the La Estrella mineral deposit, seven alteration and mineralisation events were recognised through both optical and automated electronic mineralogical analysis. Of these seven events, five different types of pyrites were identified, each with unique characteristics of the pyrite crystals. Through advanced elemental analysis of these five types of pyrites, it was determined that the concentration and distribution of cobalt within the pyrite crystal is dependent on the mineralisation event. The results indicate high cobalt concentrations in the early pyrite mineralisation events, associated with relatively fine pyrite grains, and cobalt generally occurring in a solid form in the pyrite core. The late pyrite mineralisation event exhibits the lowest concentrations of cobalt, with cobalt predominantly present along the outer periphery of the pyrite. These results are relevant from a metallurgical point of view because the preferential location of cobalt within the pyrite crystal will influence the maximum metallurgical recovery of cobalt. For this, a cobaltiferous pyrite concentrate must be formed which, according to the characteristics of pyrite, must be processed with the optimal solubilisation method. The overall objective is to ensure both good cobalt recovery and a high concentration of cobalt in the leach solution resulting from pyrite leaching. Keywords: Cobalt, pyrite, IOCG, copper, metallurgical recovery, solubilisation, Chile

Jan 1, 2020

By J. L. Havenga, L. J. van der Walt, J. T. Nel, H. Bissett

"SynopsisNew technologies used to manufacture high-quality components, such as direct laser sintering, require spherical powders of a narrow particle size distribution as this affects the packing density and sintering mechanism. The powder also has to be chemically pure as impurities such as H, O, C, N, and S causes brittleness, influence metal properties such as tensile strength, hardness, and ductility, and also increase surface tension during processing.Two new metal powder processes have been developed over the past few years. Necsa produces zirconium powders via a plasma process for use in the nuclear industry, and the CSIR produces titanium particles for use in the aerospace industry.Spheroidization and densification of these metal powders require remelting of irregular shaped particles at high temperature and solidifying the resulting droplets by rapid quenching. Spherical metal powders can be obtained by various energy-intensive methods such as atomization of molten metal at high temperatures or rotating electrode methods. Rapid heating and cooling, which prevents contamination of the powder by impurities, is, however, difficult when using these methods for highmelting- point metals. For this reason plasma methods should be considered.Thermal plasmas, characterized by their extremely high temperatures (3000–10 000 K) and rapid heating and cooling rates (approx. 106 K/s) under oxidizing, reducing, or inert conditions, are suitable for spheroidization of metal powders with relatively high melting points. Thermal plasmas for this purpose can be produced by direct current (DC) plasma arc torches or radio frequency (RF) inductively coupled discharges. In order to obtain chemically pure spheroidized powder, plasma gases such as N2, H2, O2, and CH4 cannot be considered, while Ar, Ne, and He are suitable. Neon is, however, expensive, while helium ionizes easily and it is therefore difficult to obtain a thermal helium plasma at temperatures higher than 3000 K. Therefore argon should be used as plasma gas. Residence times of particles in the plasma region range from 5–20 ms, but this is usually sufficient as 7–8 ms is required for heating and melting of titanium or zirconium metal particles in the 30 µm size range at 3500 K. In this study the melting and spheriodization of titanium powders was investigated by DC non-transferred arc and RF induction plasma methods. The powders were characterized before and after plasma treatment by optical microscopy and scanning electron microscopy (SEM) to observe if any melting or spheroidization had occurred."

Jan 1, 2015

By K. C. Sole, M. E. Mitshiabo

Although surfactants have proven to increase metal extraction by improving solution flow in porous media, these reagents have not been widely adopted in heap leaching operations because of potential incompatibilities with downstream processes that are subject to surface properties. The BASF leaching aid, LixTRA 118, was previously found to have no significant effect on post-leach operations. This study evaluated its performance in ores of different particle size distributions and the impact on acid consumption and metal recovery. Column leach studies, carried out on a copper oxide ore and mixed oxide–sulfide ore, showed that the effect of LixTRA 118 was more pronounced in ores with wider particle size distributions than in those with more uniformly sized particles. Solution percolation rates increased by up to 18% in the presence of leaching aid, and increased copper recovery and acid consumption. Improved wetting facilitated the kinetics of acid diffusion at macroand micropore level. There was no significant effect on iron recovery

Jan 1, 2023

By F. Rosenblum, K. E. Water, J. A. Finch, S. Moon, Y. H. Tan

Previous work has shown that sulphide self-heating occurs in three distinct stages referred to as Stage A, Stage B and Stage C. In this paper the focus is on the transition from Stage A to Stage B, which occurs at ca. 100OC. Background literature hints that the transition corresponds to the transformation of the rhombic form of elemental sulphur to the more reactive monoclinic form that occurs at 96OC. A test apparatus is modified for adiabatic heating to track the transition. The results support this transformation of sulphur as being key to the transition, and the transition temperature is thus modified to 96OC. Variations in a sample’s response under adiabatic conditions are observed and possible reasons are discussed. Testing in adiabatic mode provides new insights into the sulphide self-heating process that complement the test designed to identify propensity to self-heat. Keywords: Self-heating; Stage A/Stage B; transition; rhombic/monoclinic elemental sulphur; adiabatic heating

Jan 1, 2020

By D. F. Malan, J. A. L. Napier

This paper describes some important aspects associated with historical underground measurements in South African gold and coal mines. Deformation measurements were used to confirm the use of elastic theory to simulate the rock mass behaviour in the Witwatersrand gold mines in the 1960s. Although a prominent time-dependent component of stope closure was measured as early as the 1930s, it was ignored owing to the benefit of adopting elastic theory. Neglecting the time-dependent response of the rock for many decades resulted in important aspects such as the effect of mining rate, the effect of advance per blast, and the need for enhanced design criteria not being explored. Recent work is only now starting to address this gap in knowledge. In-situ measurements of large coal specimens in the 1960s and 1970s indicated that a linear formula may possibly be a better approximation of coal pillar strengths. This alternative formulation was never adopted, however, as the power law strength formula was already deeply entrenched in the industry at that stage. In spite of these apparent failures to continuously generate and adopt new knowledge, a key lesson learnt is that major advances in rock mechanics will not be possible without careful monitoring of the rock mass behaviour in experimental sites. Areas requiring further research, such as pillar strength formulae for the Bushveld Complex and enhanced design criteria for the gold mines, can only be developed using extensive undergroundmonitoring programmes.

May 1, 2021

By F. Magweregwede, S. Khan

Circular economy opportunities for the mining sector are presented in this paper. A literature review was undertaken, followed by qualitative data gathering through survey questionnaires and unstructured interviews, and stakeholder engagements through workshops. The circular economy opportunities were identified and categorised according to the three circular economy principles of designing out waste and pollution, keeping products and materials in use, and regenerating natural systems. Opportunities aligned with the first principle include increased ore extraction efficiency processes, water recovery and recycling, substitution of raw materials, technology and waste utilisation for carbon capture and biotechnology. The second principle includes opportunities such as zero waste-to-landfill strategies, repurposing of mine waste, re-mining of tailings, recycling metals and processing of residues, and urban mining of electronic waste. Opportunities aligned with the third principle include the adoption of renewable energy, green hydrogen production, repurposing of post mining landscapes, and eradication of alien invasive vegetation. Furthermore, the challenges of implementing circular economy in the mining sector are discussed. The current rate of waste generation from mining activities far exceeds the rate of reuse and repurposing. Recycling of large tyres and characterisation of hazardous electronic waste also pose challenges. The most implementable circular economy opportunities in the mining sector are those aligned with the second principle of keeping materials in use. The high impact opportunities aligned with the first principle of designing out waste and pollution, and the third principle of regenerating natural systems, are more difficult to implement as they require large investments.

Dec 15, 2025