Search Documents

Jan 1, 1927

Jan 1, 1950

Jan 1, 1934

Jan 1, 1957

MR. D. HARRINGTON (U. S. Bureau of Mines) : I happen to be a member of the Safety Committee, and the men on the Committee, I believe are the ones who will find the most fault with the report; but I am absolutely not in accord with the last recommendation. (The use of the "Self-Rescuer.") I do not think it safe. I do not think you are always sure you are going to have a sufficient amount of oxygen; in fact I know there are occasions in mines when there is not enough oxygen to make a man safe in a gas mask or self rescuer. At one mine fire, workers using open oil and carbide lights experienced quick reversal of air which extinguished the lights and one of the workers having carbide light was overcome. It took about 45 minutes hard work with Sylvester method of artificial respiration to restore him to consciousness. Fortunately these men were working close to fresh air but had they been far from fresh air base and relying upon self-rescuers or gas masks they would undoubtedly have perished. I was at a mine fire in Wyoming. A bunch of men were working and the air turned on them, and if they hadn't oxygen breathing mine rescuing apparatus I think there would have been at least a half dozen men killed they would have been killed before you could say, "Jack Robinson." PRESIDENT PRYDE: I would like to ask if the self-rescuers are nut approved by the Bureau of Mines? MR. HARRINGTON: They are not; absolutely not.* Furthermore, the Bureau of Mines' Engineers have opportunities to go around in mines, and in mine cars as much as anybody else in the country, and I have in mind but one who is in the slightest degree in favor of allowing self-rescuers to go in a mine. MR. BEVAN: Mr. Chairman, I would like to ask the Safety Committee if it would be of any use to the fire boss traveling through the mine? PRESIDENT PRYDE: Mr. Chairman, I think we should finish up the discussion on the self-rescuer before we take up any other discussions.

Jan 1, 1924

Jan 1, 1932

Jan 1, 1957

Jan 1, 1941

Jan 1, 1969

[Mr. Houston T. Aars Carter Mining Co PO8 3007 Gillette, WY 82716 Mr. Jay Abbott Union Supply Co 7458 S Jackson St Littleton. CO 80122 Mr. Ronald H. Achziger Midwest Rbr & Sply Co 6404 E 39th Ave Denver, CO 80207 Mr. Randy Acre Dorchester Coal Co 9350 E Arapahoe Rd Englewood, CO 80112]

Jan 1, 1983

[ACC, Inc. Bucyrus-Erie Company CINCO (Coal Industry Consultants, Inc.) Coal Magazine Colowyo Coal Company Coors Ceramic Company Crane & Hoist Sales, Inc. Cummins Power. Inc. Cummins Southwest, Inc. Cyprus Coral Company Denver & Rio Grande Western Railroad Company Energy Fuels Corporation FMC Corp.- MHE Division Ford. Bacon & Davis Inc. T.J. Gundlach Machine Company Hemscheidt American Corp. GH Hensley Industries Honnen Equipment Company Jennmar Corporation Soy Technologies, Inc. K&P Sales Engineers, Inc. Kennametal, Inc. Kerr McGee Coal Corp. McLanahan Corporation National Mine Service Company Peabody coal Company Pitrsburg & Midway Coal Mining Co. Pyramid Parts, Div. American Alloy Ramsey Technology. Inc. Roberts & Schaefer Company Santa Fe Pacific Coal Corporation Scandura. Inc. Tamarron Resort TIC (The Industrial Company) Tribol Utah Power & Light Western Energy Company]

Jan 1, 1988

By Richard Woodward

Presentation Outline ?What types of coal analyzers are there? ?What do they measure? ?How do they work? ?How accurate are they? ?Most common applications ?Sorting ?Blending ?Prep plant optimization ?Boiler Control

Jan 1, 2006

Jan 1, 1929

Jan 1, 1935

Jan 1, 1948

By D. C. McKeehan

The importance of properly bonded rail joints has received the attention of The National Research Council, whose committee will investigate several methods now used and determine the merits of each as applied to street railways. The results of this investigation should be appreciated no less by the mining industry. Literature on the subject of bonding mine tracks agrees, as a rule, "that the work is poorly done." With present day facilities there is little excuse for inadequate track conductivity, and a job well done must be maintained in order to realize results. Many years ago The Union Pacific Coal Company installed their first haulage locomotive, and at that time used the channel pin bond for joining the rails. The system utilized 500 volts and the, relatively small current for a large amount of power, undoubtedly, contributed to the success of the system. The bonding of both rails was considered imperative in those days, while now the bonding of one, rail is considered sufficient in most instances. The recent installations utilizing 250 volts and correspondingly heavier currents required a more effective method of joining the rails for use as an electrical conductor. The company has used the arc-weld bond since its introduction in 1919. The art of electric welding found great favor for various methods of doing the work. The first arc-weld bonds were placed on the outside of they ball of the rail, but the bonds were ill-adapted to rails lighter than sixty pounds per yard, and the results were that grooved locomotive wheels or derailed cars removed the bonds. Familiarity with the process of electric welding brought forth numerous schemes for joining the rails. In one, instance the rails and splice-plates were welded together and with excellent results for a short time. Track movement and vibration finally broke the welds and the method was dis¬carded. Another scheme consisted of placing a channel pin over each end of an annealed copper wire about twenty inches long. The idea was to develop some way of using short lengths of scrap wire. The pin and wire were then welded to the base of the rail. Numerous joints made in this way are still intact, but successful welds were so exceptional that the practice was abandoned. Some of these bonds were welded to the web of the rail, with the result that practically all rails broke at the weld; however, this is our only record of broken rails with arc-welded bonds. At one time a quantity of No. 2 bare iron wire wasp available and was tried as a bond and proved very satisfactory. Two or three strands twenty inches long were used and were welded to the base of the rail. The method was cheap and effective and of some merit for light rails on temporary track. The use of iron wire was criticized because it did not give a balanced circuit; that is, one having equal carrying capacity for trolley and track circuits; and I am of the opinion that this is not always necessary. The total length of bond that is in circuit is so small that it contributes very little additional resistance to the complete circuit consisting of trolley wire, rails and bonds.

Jan 1, 1923

Jan 1, 1951

John P. Thomas, President. B. W. Snodgrass, Secretary-Treasurer. San Andrews, mine boss, Morley. Richard Bickerton, Tabasco. E. P. Bayles, superintendent, Cokedale. Clyde Campion, parting tender, Valdez. O. C. Cook, 406 East Seventh, Street, Trinidad. James Cameron, superintendent, Hastings. Charles Chambers, superintendent, ,Sopris. Arthur Dennison, Trinidad. Samuel Dean, mine inspector, Delagua. F. S. Dunlevy, assistant engineer, Hastings. L. R. Douglas, assistant engineer, care Danford & Sanderson, Trinidad. W. E. Danford, superintendent, Segundo. M. O. Danford, superintendent, Cedar Hill Coal & Coke Co., Trinidad. John Dougherty, mine foreman, Morley. J. C. Davidson, timberman, Valdez. William Easton, fire boss, Valdez. George Fortune, electrician, Primero. D. J. Griffiths, chief mine inspector, Trinidad. J. E. Hanes, assistant engineer, Hastings. Joseph Haske, superintendent, Primero. O. C. Erwin, electrician, 714 Pine Street, Trinidad. R. J. Jinkins, superintendent, Morley. Thomas jolly, superintendent, Gray Creek. James Jamieson, assistant mine boss, Valdez. James Kilpatrick, fire boss, Tobasco. L. M.. Kuhns, first-aid miner, care Mine Safety Car No. 2, Trinidad. William B. Lloyd, 404 East Seventh Street, Trinidad. J. C. Lawrence, machinist, Starkville. R. A. McAllister, mine inspector, Trinidad.

Jan 1, 1913

By George A. Brown

Flexoid tubing for ventilation and some of the reasons for its use in re-opening old workings at the Union Pacific Coal Company's mines at Cumberland, Wyoming. , These mines are located on a branch line off the Oregon Short Line Railroad, about sixteen miles south of Kemmerer. The seam averages from 16 feet to 20 feet thick and is split about six feet from the bottom with from six inches to four inches of fire, clay; and is covered by a heavy sandstone roof about 45 feet thick and a fire clay floor about 15 feet thick. Pitch of seam 21 degrees. These mines were opened up with 5 openings on the pitch to the west, with main slope, north and south manways and north and south aircourses on 50-foot centers with parallel entries driven north and south at right angles to the slope and rooms turned on 50-foot centers up the pitch ; entries being 350 feet apart and chutes used in the rooms. Several years ago there was a heavy, squeeze came on these mines which necessitated shutting down all of No. I Mine below the third entry, the slope being down to 12 entry; also shutting the lower end of No. 2 Mine down from the twelfth entry to fifteenth entry and from the third entry down to the tenth entry, so as not to work too much territory at the one time. These mines are very gassy and were subject to heavy bumps during the squeeze ; also at the present time. In reopening these slopes, aircourses and entries for the recovery of the pillars, ventilation was quite a problem, as the squeeze had caused them to be practically tight; also the rooms for about 50 feet from the entry and the face of the rooms for about fifty feet. These rooms in the open space being either filled with Methane or depleted air. It was found in opening up these entries that in driving back entries parallel with the top entries for ventilation. which had to be skipped along the barrier pillar left from the face of the rooms of the entry below, that we had more bumps or bounces which made it a dangerous proposition to nine, as it will be noted as stated that the entries, room necks and face of rooms were more or less squeezed tight, showing that all the weight was centered on these points and the more they were disturbed the more it relieved the overlying pressure and something had to give; hence the bumps or bounces which have filled slopes, aircourses, entries and rooms with coal from the ribs and face, for hundreds of feet, throwing cars off the track, both loads and empties, and throwing track up to the roof and discharging timbers. We found it necessary to abandon driving back entries and have used Flexoid tubing with small blower fans to open up these slopes, aircourses and entries which has proved a success. We have carried air for distances that would have been impossible with brattice cloth or with

Jan 1, 1921

Jan 1, 1952