Search Documents

By L. A. Johnson

The Bureau of Mines analyzed three cores from the south Seep Ridge area of the P. R. Spring tar sand deposit of northeastern Utah. Four tar sand zones are indicated in the area. The zones range in average thickness from 13 to 24 ft. The total net thickness of the tar sand in the three coreholes ranges from 71 to 112 ft. The tar sand occurs between the depths of 27 and 254 ft. It has good porosity, 25.6 pct of bulk volume; high permeability before and after oil extraction, 819 and 2,218 md, respectively; but a relatively low oil saturation, 36.5 pct of pore volume. Gravity of the oil ranges from 8.20 to 16.5° API.

Jan 1, 1975

Develop methods of enhancing and measuring the high-temperature softening and melting properties of iron oxide pellets reduced under simulated blast furnace smelting conditions. Approach Add dolomite and Limestone flux and a low-cost organic binder, such as starch, carboxyl methylcellose (CMC), or waste papermill sludge, to the iron oxide concentrate to produce hematite (ferric oxide) pellets with superior high-temperature metallurgical properties. Simultaneous increases in softening temperature, gas permeability, and enhanced metallization rates are sought to improve blast furnace productivity and energy efficiency. Background In the past, bentonite, an inorganic binder, was the only additive (binder) used in the production of pellets made from iron ore concentrate. Research has shown that the reducibility of conventional (acid) pellets can be increased by the addition of flux or an organic binder. The increase in pellet reducibility results in less wustite in the center of the pellet at high temperatures, such as those obtained in the cohesive zone of the blast furnace.

Jan 1, 1990

By Robert C. Hickman

"INTRODUCTION Two holes were drilled on the G. S. Stiner zinc prospect, in the Lead Mine Bend area of Union County, Tenn. The holes were drilled in the vicinity of an area of gossan float and were bottomed in the Maynardville formation of the Nolichucky shale. Drilling was started January 24 and completed February 16, 1947. The total footage drilled was 421.2 feet.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, does the actual investigative Work, and prepares the final report. The Metallurgical Branch, Cliver C. Ralston, chief, analyzes samples and makes beneficiation tests.The project was under the general supervision of Mitchell H. Kline, chief, Raleigh Division, Mining Branch, Raleigh, N. C.LOCATION AND ACCESSIBILITYThe prospect is located approximately 20.5 miles southwest of Tazewell, Tenn. It is reached from Tazewell by driving 13.8 miles southwest on State route 33, thence 6.8 miles over graveled roads in a northwesterly direction to Stiner's general store. The drill holes are located in the bottom land northeast of the store (fig. 1 and 2)."

Feb 1, 1948

Reliably measure stress chan¬ges in order to assess stability of mine openings. Approach: A durable, permissible, sensor and readout system have been developed and tested. How It Works: The stress sensing element is a taut steel wire which is, vibrated at its natural frequency, If the tension on the wire is changed because of deformation of the sensor housing, the natural frequency of the wire changes. This effect is similar to decreasing or increasing the pitch of a violin string by loosening or tightening it. Because the stress sensor electrical output is a frequency signal, rather than an amplitude signal, its accuracy is unaffected by the resistance of the signal wire, or other attenuation. Signal wires can be a mile or longer without affecting accuracy. When a button is pushed on the readout box, the sensor wire is electromagnetically excited and vibrates at its natural frequency. That signal causes a readout in illuminated digits. (By referring to calibration chart and the previous reading, the user knows the change in stress.) This system is permissible. To install the sensor, a slightly oversize hole is drilled into the mine pillar. Next, a special tool is used to both position the sensor and wedge it in place. Figure 1, shows the sensor and its integral wedge and hole-fitting piece.

Jan 1, 1976

By J. K. Whyatt, B. G. White

Various methods of monitoring slip movements on bedding planes, as well as examination of rock burst damage in stopes, suggest that many rock bursts in the Lucky Friday Mine are closely associated with these movements. Slip displacements along bedding simultaneously reduce the physical dimensions of stopes and increase compressive stress along stope margins. Such changes, in turn, contribute directly to sudden failures of rock and cemented sandfill surrounding stopes. We believe that the reduction of rock burst hazards must be based on a clear understanding of the basic mechanisms involved. The current work emphasizes the mechanical role of wall rock movement and seismicity in generating conditions that promote rock burst damage. Based on our interpretations of these mechanisms, we briefly address several hypothetical practices that could influence rock burst hazards in similar mining situations. The overall goal of this research is to advance the NIOSH mission of improving the health and safety of the nation’s workers.

Reduce the noise levels to which operators of double-drum longwall shearers are exposed without compromising the operational effectiveness of the shearer. The Problem Noise produced by double-drum longwall shearers can be harmful to machine operators. Typical noise levels at the lead-drum operator position range from 100 to 105 dBA, and Federal noise regulations allow only one to two hours of exposure per shift at these levels. Noise radiated by the shearer cutting drum is the primary contributor to the overall noise level. However, test of a noise-controlled cutting drum developed by the Bureau of Mines reduced the operator noise level to 95 dBA, thereby increasing the allowable operating time to four hours per shift. Approach The key design aspect of the noise-controlled shearer drum is its reduced vibration-al response to coal-cutting forces. Laboratory studies have shown that these forces are concentrated in the low-frequency region (500 Hz and below). Since the cylindrical core and the cantilevered I plate-like helix of the standard shearer drum are easily excited by these forces (natural vibration frequencies be-

Jan 1, 1985

Reliably detect fires by sensing sub-micrometer-sized particles released into the air by smoldering or burning materials. Approach An extremely sensitive, ionization-type fire detector has been built that continuously draws air samples through its ionizing field and collects the ionized smoke particles downstream, thereby generating a proportional electrical output signal. (An offshoot instrument measures the size distribution and number of sub-micrometer particles in air.) How It Works Mine air to be monitored is drawn through the instrument assembly by a small pump. A pre-filter and cyclone remove dust particles and other particles larger than 0.6 micrometer diameter. The air and remaining aerosol-sized particles flow through a gastight tube which contains the detector. See diagram. Smoke and other sub-micrometer-size particles moving Into the detector, pass through an Ionizing field, and are struck by alpha particles released from radioactive source located on the axis of the tube, The alpha particles move radially outward until they strike smoke particles or molecules of air or water. When struck, a smoke particle or molecule loses an electron and becomes positively ionized.

Jan 1, 1979

By Launa Mallett

This training material focuses on the content of emergency warning messages. Research has shown that when an emergency occurs, people often do not get the information they need for the purpose of taking appropriate action. This safety talk presents a procedure, using mental cues that can be used by senders and receivers of emergency warnings.

Jan 1, 1999

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

The program MFIRE consists of four files MFIRE0 EXE, MFIRE1 EXE, MFIRE2 EXE, and MFIRE BAT The batch file, MFIRE BAT, controls the operation and cooperation of the three executable pro¬gram files and the output Networks of up to 500 air¬ways and 350 junctions can be modeled in the PC version of MFIRE Larger data sets can be accommodated by increasing array dimensions and compiling the program again. Input for MFIRE is in the form of a data file The data file contains fines of numerical data describing the physical mine, the ventilation parameters present, the fans, and the proposed thermal or mechanical disturbances

Jan 1, 1990

By Joseph E. Chilton, Robert J. Timko, Charles D. Taylor

No regular monitoring of methane is required in areas of gassy coal mines outby the mining face. Methane ignitions that have occurred in mine outby areas indicate the need to provide better protection to workers. Handheld methane monitors are now used by some miners to make periodic measurements of methane at the working face. The IYONI II gas detector which is incorporated into a miner’s cap lamp and worn on a miner’s helmet can continuously provide an alarm signal whenever methane levels exceed a set level. Tests were conducted to evaluate the performance characteristics of this methane detector by measuring response times with methane gas supplied through a calibration fixture or adaptor. Other response time tests were performed with the detector in an environmental test box. Performance was also evaluated in a full scale test gallery where face methane emission and underground ventilation were simulated. Procedures for calibration by response time measurement of the IYONI II detector have been developed. In limited testing, the IYONI II detector was found to reliably detect the presence of 1 percent by volume methane.

By Lewis V. Wade

Barrett EA, Kowalski KM [1995]. Effective hazard recognition training using a latent-image, three-dimensional slide simulation exercise. Pittsburgh, PA: U.S. Department of the Interior, Bureau of Mines, RI 9527. NTIS stock number: PB95-170379. Beus MJ, Orr TJ [1995]. Computer modeling and analysis of the Greens Creek mine, Admiralty Island, AK. Spokane, WA: U.S. Department of the Interior, Bureau of Mines, RI 9530.NTIS stock number: PB95-176418. [ ]

By Fred C. Turin, Kim M. Cornelius

Work in underground coal mines is repetitive and physically demanding. Workers commonly report a wide range of aches and pains. Management at one mine was concerned about increased reporting of aches and pains by roof bolting machine operators. An analysis of roof bolting tasks was conducted at this mine to identify early warning signs of cumulative trauma. Health and safety risk factors were identified and recommendations to reduce cumulative trauma exposure were provided. Recommendations addressed job procedures, equipment design, and worker awareness of risk factors.

Continuously monitor air-borne radon daughters that are a hazard to underground miners. Approach A beta detector continuously counts beta activity collected on a filter paper to allow calculation of exposure in working level units. How It Works At each Site a constant flow pump draws mine air through a fiberglass filter located in front of a beta detector (pancake type Geiger Mueller tube), Radioactive particles (products of the radon 222 gas emanating from the mine walls) collect on the filter and decay, releasing alpha and beta particles as well as gamma rays. A portion of the beta particles penetrate the Geiger tube window and create electrical pulses in the tube. These pulses are then amplified and sent by a coaxial type or shielded electrical cable to a central monitor located some distance from a working level detector. At the central monitor incoming Signals are amplified and fed into two channels, (See the block

Jan 1, 1979

The extrapolation of results from reconstructed laboratory soil columns to field conditions is difficult because of the limitations of laboratory experiments. Permeability and elution tests performed in the laboratory differed from the natural state in that the soil was sieved through 1/4 inch screen to remove large stones and roots, its density was controlled by tamping the soil into two-inch I.D. tubes instead of normal weathering, and water and latex were applied with a constant head of liquid. Tube wall effects are important in interpreting data. Conversely, interpretation of field results were confounded by non-homogeneities within the sample tested, a soil profile with gradation of permeability and density with depth, and uncontrolled weather conditions and seasonal changes that affected the results. Nevertheless, both laboratory and field tests showed that a specific latex did perform as a soil sealant. In view of these facts a soil box experiment was designed to overcome some of the disadvantages associated with the small laboratory soil columns and the field experiments. Two wood soil boxes 5 ft x 5 ft x 5 ft were built in the greenhouse at the Uniroyal Research Center. They were lined with plastic PVC sheeting provided with tubes every six inches of depth on one side of each box to measure water removal rates under saturated conditions. Tensiometer gauges were placed at depths of 6, 12, 18, 24, 36 and 48 inches and Bouyoucos blocs and resistance thermometers were positioned at 6, 24 and 48 inch depths. Each box was filled with a uniform sub-soil obtained from Ogdensburg, N. J. The texture of this soil was determined to be a sandy loam by the ASTM Hydrometer method, as shown below: [ ] The boxes were thoroughly wetted by sprinkling to abet settling and allowed to dry by draining to check seepage ports and functioning of tensiometers.

Jan 1, 1972

By Stephen W. Lambert, Michael A. Trevits

The Bureau of Mines examined the wellbore of a vertical gas drainage well in the Mary Lee coalbed to determine the results of specific completion procedures in coal. A jet-slotting tool was used to cut four vertical slots through the casing about 1 ft below the coalbed. Even though stimulation treatment pressure was excessive, hydraulically induced channels were contained entirely within the target coal zone. Sand-filled, induced channels were horizontal, inclined, and vertical, and were propagated in directions similar to bedding planes, rock joint, and coal cleat directions measured in the mine. Variable gas flow rates, recorded during the productive life of the well, were attributed to chronic downhole pump malfunction and the slotted casing below the production zone.

Jan 1, 1978

By R. Larry Grayson

Barrett EA, Kowalski KM [1995]. Effective hazard recognition training using a latent-image, three-dimensional slide simulation exercise. Pittsburgh, PA: U.S. Department of the Interior, Bureau of Mines, RI 9527. NTIS stock number: PB95-170379. Beus MJ, Orr TJ [1995]. Computer modeling and analysis of the Greens Creek Mine, Admiralty Island, AK. Spokane, WA: U.S. Department of the Interior, Bureau of Mines, RI9530. NTIS stock number: PB95-176418. [ ]

By E. C. Lane

The motor gasoline that is being marketed in the United States this winter (1928-29) is slightly more volatile than that gold a year ago. This characteristic is shown by a slight lowering of the distillation temperatures, particularly at the average initial and 20 per cent boiling points. Daring the past mine and a half years the Bureau of Mines has made semi annual surreys of the gasoline marketed in the United States; the Survey just completed is the nineteenth in the series. The 12 cities in which samples have been collected were chosen as representative of the more important marketing territories, as it was obviously impracticable to obtain a sample of every gasoline sold in the entire country.

Jan 1, 1929

By E. O. Binyon

The Blue Metal corundum-andalusite deposit, in the Buckskin Mining district, Douglas County, Nev., was explored by the Bureau of Mines in 1945. The results of that work were presented in Report of Investigations 3895, exploration of the Blue Metal Corundum Property, Douglas County, Nev. published in August 1946. That report also describes the property in detail, giving location, ownership, history, geology, and data on beneficiation tests. Further exploration was carried on in April and Way 1947, the results of which are presented in this report. The work consisted of 175 feet of drift and crosscut, bringing the total to 398 feet of underground working, as shown in figures 1 and 2. The 23-foot drift, which was the last work of the initial project, was extended 99 feet northward along the shear zone, and three crosscuts, spaced at approximately equal intervals along the drift, were driven to country rock on the hanging and foot walls of the zone.

Jan 1, 1948

By Yael Miron

Ammonium nitrate-fuel oil (AN-FO) mixtures are used as blasting agents in mining pyrite-bearing ores. The temperature of these ores can increase by the continuous, though at times slow, oxidation weathering of the pyrites. At elevated temperatures, AN-FO reacts exothermally with pyrite, and the reaction becomes self-sustained at 120° C ± 10° C. The Bureau of Mines has conducted an investigation to determine the reactivity of mixtures of AN-FO with pyrite containing ferrous sulfate. The results of tests in a heated vessel simulating a hot borehole demonstrate that small amounts of ferrous sulfate, a major product of pyrite weathering, initiate a self-sustained exothermic reaction with AN-FO at 80° C. Five pct by weight of urea was found sufficient to prevent a reaction among the three ingredients, at least within the limits of the test, which reached 180° C. Smaller amounts of urea and of potassium oxalate slowed down the reaction and delayed its onset to higher temperatures, but did not prevent it.

Jan 1, 1979

By Fred Baldassare, Marcia Harris, Kenneth K. Eltschlager

Surface mine blasting was recently investigated as a potential source of high concentrations of stray gases found in nearby residences of western Pennsylvania. In one incident carbon monoxide was detected in a home and in the other, high concentrations of carbon dioxide were found in a home. Both carbon monoxide and carbon dioxide are by-products of blasting. However, other potential sources of these gases may also exist in a residential setting. In each case, gas chromatography (GC) and carbon isotopic analyses were used to define atmospheric concentrations inside the homes, and to determine the source of a stray gas. Molecular and isotopic analyses provide geochemical evidence as to the origin and source of the stray gas. This paper discusses elements of a stray gas investigation and the analyses necessary to identify the source of a stray gas.