Search Documents

By L. H. Wullstein

Bureau of Mines research on methods for reclaiming land disturbed by the minerals sector of the economy has produced a specific procedure for effectively germinating seed of Indian ricegrass, a drought-tolerant plant valuable for reclaiming arid and semiarid sites. This report describes the procedure which consists of acid-treating the seed followed by temperature and light cycling treatments. Use of the procedure resulted in an average germination rate of 29 percent, ranging from 18 to 56 percent. Seed subjected to long cold treatment but with acid treatment yielded an average germination rate of 9.2 percent, ranging from 6.6 to 14.7 percent. Untreated seeds (controls) gave germination rates less than 0.1 percent.

Jan 1, 1979

By A. F. Colombo

The differences in starch demands that occur between ore types subjected to the anionic flotation of calcium-activated gangue and the range of residual starch contents expected to give the best metallurgical response were evaluated on a batch and pilot plant basis. A phenol-sulfuric acid procedure was used to determine the residual starch contents in the iron ore slurries. Three pilot plant campaigns on samples from a group of orebodies located on the Marquette Range, Michigan, showed that in the rougher flotation pulp, a residual carbohydrate range of 25 to 100 ppm, which is equivalent to a 0.5 lb/short ton spread, yielded optimum results. Concentrates assaying at least 65 percent Fe and less than 6.0 percent Si02 and containing more than 80 per-cent of the recoverable iron were obtained. Both batch and continuous research indicated that starch adsorption is calcium modulated and relatively unaffected by the fatty acid additions employed. Residual starch level is not a critical control factor, but the addition must be adjusted to about 25 to 50 ppm residual starch and kept in this range for most effective utilization of the added tapioca flour.

Jan 1, 1972

By R. V. Thurston, Edmund S. Leaver

"During the development of the sulphur dioxide leaching process for the treatment of ""mixed"" copper ores at the Southwest experiment station of the Bureau of Mines*** the pulp from treatment of roasted cupriferous pyrite with sulphur dioxide gases and water showed an unexpected amount of sulphuric acid. After following out several false premises it was found that this was due to iron in the solution, and also that this iron tended to oxidize to the ferric state if the concentration of sulphur dioxide in the roaster gases used did not rise above a certain figure. While the percentage of iron present was email it was enough to cause an entirely different set of conditions from those of the original sulphur dioxide leaching process and to promise a much wider application of the general idea. Sulphurous acid dissolves only certain copper minerals, sulphuric acid solutions certain additional minerals and ferric sulphate solutions certain further additional copper minerals, so this observation was of importance in connection with possibilities in the hydrometallurgy of the so-called ""mixed"" or partly oxidized copper ores.The work has been carried along by a number of experimenters. L. R. Eckman, junior chemist of the Southwest station, contributed largely to the early developments. L. Roberts, W. D. Bonner and C. G. Maier each in turn physical chemists at the Pacific Experiment station, (Berkeley, Calif.) have studied the reactions involved. A complete report of all the work on this process will be prepared later under the direction of O. C. Rolston. The purpose of the present paper is to place a summary of the more practical phases of this seemingly important piece of work before those interested."

Dec 1, 1923

By W. D. Walker

This information circular is offered to the coal-mining industry for use as a guide in selecting, placing, and caring for fire-fighting equipment in coal mines. Its purpose is to suggest minimum requirements for fire protection underground, and it is presented with the hope that it will aid in establishing adequate standards that will provide reasonable protection against underground fires in coal mines. Potentially, a coal mine is a hazardous fire area. Coal itself is a combustible substance, easily ignited. In addition, large quantities of other combustible materials must be present in the area of operations; these include materials for roof support, track ties, doors, ventilation stoppings, lubricants, etc.

Jan 1, 1953

By C. M. McCulloch

As part of the Bureau of Mines methane control program, the Pittsburgh coalbed was studied in Washington and Green Counties, Pa., and in Marion and Monongalia Counties, W. Va., where this coalbed is now being mined at its greatest depth. The coalbed thickness appeared to be structurally controlled; the bed was generally thinner near the axes of anticlines and thicker near the axes of synclines. The overburden isopach shows a similar relationship. Most of the clay veins in coal occur in the synclinal troughs, generally under sandstone roof. Cleat orientations measured in 18 underground mines showed that face cleats are perpendicular to the axial trends of the folds, and the butt cleats are parallel to the axial trends, indicating structural control of the cleat. Measurement and analysis of surface joint orientations provide a method for predicting the cleat orientations of the coalbed, but linears measured from infrared photographs and photoindex sheets helped only to determine regional trends. The results of these investigations provide a geologic framework for rational planning for underground mine development to use the best available technology to cope with methane emissions, coalbed discontinuities, and related ground support problems.

Jan 1, 1975

By Lloyd A. Morley, Robert Stefanko

Table

Jan 1, 1974

By C. W. Owings

When explosions have occurred in mines where rock dust has been used to some extent, generally to a very limited extent, the press has immediately characterized those mines as "rock-dusted." To persons familiar with the method of rock-dusting, it is apparent that if rock-dusting is done properly, if all mine surfaces are rock-dusted to within at least 40 feet of the faces of rooms and entries, and if the incombustible content of the dust is more than 65 per cent, there is little likelihood that an explosion of coal-dust will occur. The report that an explosion has occurred in a "rock-dusted" mine immediately conveys to the mind of the alert safety advocate the information that the mine is inadequately rock-dusted or that either dust sampling of the rock-dusted surfaces has not been done or, if done, the mine has not been redusted with sufficient promptness. Rules for Collection of Samples Collection of dust samples is by no means intricate, but a few simple rules must be kept in mind if the results are to be dependable. A sample must represent the true average conditions of the dust in the section or zone in which it is taken, and therefore 'the point at which the sample is to be collected must be selected with care. During an explosion much if not all of the dust on the ribs, roof, timber, and road in the affected region is blown into the air; the sample, therefore, should contain all loose dust and material on: the surfaces to a depth of about 1 inch, if that amount is present. If there is considerable sand locally along the track, care must be taken not to include enough of this material to vitiate the sale and distort the results; however, if the sand is distributed throughout the region being sampled it should be included. Dust should not be collected from recesses in the ribs, such as hitches cut for timber, as the character of the dust in such places is often different from that on the ribs proper. Samples should not be collected at points where the dusting machine has been loaded or at a point where the machine has stopped and discharged for a longer period than at other points on the entry or in the rooms. In short, the sample must represent AVERAGE CONDITIONS, and if there is any doubt as to the character of the dust it is far better to have too much combustible matter than too much incombustible matter in the sample, as it is best to err on the side of safety if it is necessary to err.

Jan 1, 1929

By R. M. Santmayers

[This paper presents one of a series of digests of foreign mining legislation that is being prepared in advance of a general report relative to the rights of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the mining legislation of Bulgaria was prepared from a copy (in French) of the Mining Laws of Bulgaria, promulgated by Royal Decree No. 33 of I. arch. 31, 1910, and published in the "Journal Official," No. 83, April 14, 1910, and checked against a digest prepared by Maynard B. Barnes, First Secretary, American Legation, Sofia, Bulgaria, dated June 10, 1932, which was transmitted through the courtesy of the Department of State. CLASSIFICATION OF MINERAL SUBSTANCES Mineral deposits are classed either as mines or quarries. (Art. l.) Tunes are deposits, the products from which must be processed. Under this class specific mention is made of the metals (gold, silver, copper, lead, zinc, iron, chrome, titanium manganese, tungsten, tin, mercury, platinum, cobalt, nickel, cadmium, aluminum, molybdenum, bismith, uranium, antimony, arsenic), sulphur and other "analogous" mineral substances, phosphate rock, iron pyrites, sulphates, saltpeter, alum, boracic acid and its compounds, talc, asbestos, amber, graphite, merschaum and precious stories of all kinds, reek salt and other salt, peat, coal, petroleum, ozocerite, asphalt and all other bituminous substances. (Art. 2.)]

Jan 1, 1933

By S. H. Katz

"At the annual meeting of the International Association of Fire Engineers at Kansas City, Mo., in June, 1919, the Bureau of Mines offered to cooperate with municipal fire departments for the purpose of obtaining information regarding composition of the air in burning buildings. (Katz, S. H., Statement made at Convention of International Assoc. of Fire Engineers: Fire and Water Eng., vol. 66, July 16, 1919, pp. 129-30, also Fireman's Herald, vol. 78, July 12, 1919, pp. 48.) The gas-mask laboratory of the Bureau's experiment station at Pittsburgh sent vacuum bottles for taking samples to fire chiefs in twenty-five cities, who had signified their intention to aid in this work. It was hoped to obtain one hundred or more samples, because statistics in quantity are necessary for drawing reliable conclusions concern-in the likelihoods of encountering irrespirable as in burning buildings. This far, eleven samples have been received by the laboratory. Results of analyses and pertinent data regarding these samples are given in the accompanyingEight of the eleven samples contained, no carbon monoxide; seven of the eight were taken above the ground level and one below ground. One sample taken above ground contained 0.03 per cent carbon monoxide, and this quantity is not dangerous to breathe for a limited time. Of the three samples taken below ground, one contained no carbon monoxide; the other two contained 0.10 and, 0.35 per cent, respectively. This indicates that in a burning building, the hazard from carbon monoxide is much greater below the ground level. The cause undoubtedly lies in the poorer ventilation that is usually found in cellars or basements. Abundance of ventilation provides the necessary air for complete combustion, or if incomplete combustion does occur, the carbon monoxide generated by the fire is greatly diluted with fresh air and swept away by the current. It may be noted that the highest proportion of carbon monoxide was found in a cellar where a fire as burning among piled cases. The difficult access of air to the burning parts facilitated the formation and lib ration of carbon monoxide. The smoke here was very light and no difficulty was experienced in breathing. Some of the air containing dense smoke showed little change from normal air by analysis. Thus the density of smoke or the irritation and difficulty it causes in breathing are no indication of the presence of poisonous gas. None of the samples shows important oxygen."

Nov 1, 1920

By Eugene T. Sheridan

The Bureau of Mines annually canvasses the peat producers in the United States and publishes economic data on the industry, based upon reports from producers. This publication lists all producers that reported commercial production to the Bureau for 1959. The companies named herein represent virtually all commercial producers of peat. A few companies, however, may not have been canvassed or failed to respond, as tine survey is voluntary For producers, arid the industry has many small operations that operate intermittently. No consideration was given to the quantities of peat produced and output of the various companies listed ranged from less than 100 tons to more than 50,000 tons, Peat is included in the Bureau's annual surveys of the mineral industries because, technically, peat is a fuel. Although none is used for fuel in the United States, peat is a potential source of energy and one of our large mineral resources. The domestic peat industry produces peat chiefly for use as a soil amendment. The industry has expanded rapidly during the past decade with active operations increasing from 45 in 1947-49 4/ to 105 in 1959. Output during this period has increased 218 percent, rising from 131,782 net tons to 419,460 net tons.

Jan 1, 1960

By Louis A. Panek

This report deals with the combined friction and suspension effects in the reinforcement of horizontally bedded mine roof by bolting. Other reports have treated these two effects separately. Friction effect refers to the reduction of bending in a laminated roof due to the clamping action of tensioned bolts. If the beds tend to have unequal deflections, the bolts oppose this tendency, thus creating a suspension effect, which consists of a transfer of part of the weight of weaker or thinner beds to the flexurally more rigid beds within the bolted unit. The combined effects of friction and suspension on the bending of the beds, whether an increase or a decrease, are difficult to generalize because they depend on the bedding sequence and the bolt pre-tension. Some analysis of the bedding sequence usually is required to determine the critical bed within a set of bolted beds. However, if the suspension effect is substantial and if the bolts are pre-tensioned, then the greatest bending stress is likely to occur in the thickest bed. Findings are based partly on theory and partly on tests of mine-roof models in a centrifuge, which were found to verify the theory. Mathematical formulas are obtained for the change in maximum roof bending stress and for the change of roof deflection due to the combined friction and suspension effects. The maximum bending stress is needed for designing a roof-bolting system and the deflection for evaluating its effectiveness.

Jan 1, 1962

By Charles L. Kimbell

The concept of data availability must be addressed, because there are perceptible changes from year to year, and the availability of accurately reported, precisely defined statistics and nonstatistical information provides the only sound basis for analytical studies required for government policy planning or industry market analysis. As the countries of Eastern Europe and the former U.S.S.R. undergo the transition from centrally planned economies to market economies, there has been a perceptible increase in information availability for rather obvious reasons. Any industrial operation seeking economic assistance from Government and/or private sources outside the country in which the facility is sited must provide some appraisal of its operations at the time it seeks assistance, as well as some information on previous performance to serve as tools in evaluating its potential under the proposed development scheme for which it seeks financial assistance. Additionally, there was growing governmental recognition that concealment of much of the national mineral production, trade, and consumption data for purposes of national military and/or economic security probably never was very successful, never was really necessary for most commodities, and certainly proved unnecessary with the end of the so-called cold war. Indeed, the long-term unwillingness to publish uniform statistical series of reliable,

Jan 1, 1993

By Samuel P. Harteis, Eric S. Weiss

The National Mining Association and the Mine Safety and Health Administration requested that the National Institute for Occupational Safety and Health (NIOSH) conduct full-scale evaluations of a recently developed carbon fiber-reinforced polymer (CFRP) reinforcement technique for upgrading existing mine ventilation seals to withstand an explosion pressure of 50 psi or greater. The evaluation was conducted in the NIOSH Pittsburgh Research Laboratory’s Lake Lynn Experimental Mine (LLEM) near Fairchance, PA. The purpose of the evaluation was to determine the blast resistance of the CFRP reinforcement technique, designed to increase the strength of two types of existing 20-psi-rated in situ mine ventilation seals. Two candidate ventilation seals were selected to represent the 20-psi alternative seal designs typical of those used in mines prior to July 2006. Installed within the LLEM were (1) a 4-ft-thick pumpable cementitious foam seal using material with a designed 150- to 200-psi average compressive strength at 28 days and (2) a 24-in-thick, low-density cementitious block seal with a center pilaster and keyed to the floor and ribs. The materials necessary for the CFRP reinforcement technique were then installed on the outby (active) side of each seal, and the seals were subjected to explosion overpressures. Both seals with the CFRP reinforcement retrofit successfully withstood explosion pressures of 60 psi or greater during the full-scale evaluations in the LLEM.

Jan 1, 2008

By G. Dale Cor, Will H. Coghill, M. F. Williams, I. L. Feld

"INTRODUCTION During the past several years the Southern Experiment Station of the Bureau of Mines, with the cooperation of the University of Alabama, has given attention to hydraulic classification. One of the things this work has revealed is a variability not generally recognized in the conditions of teeter at different depths. This report depicts the passage of material through a teeter column and its emergence as a classified product.The work was made possible through the development of a classifier for several hundred pounds per hour permitting a small quantity of coarse spigot material to be discharged without the usual interruptions caused by stop-pages. Previous designs of small classifiers have been unsatisfactory because the,orifice used to control the quantity of spigot product as subjectto stoppages, particularly when attempting to discharge a small quantity of although the classifier used in this work has been described in detail in a previous publication 6/ its principal features will be discussed briefly herein. The main subject matter of the paper is based upon the three figures that illustrate in panorama the conditions that exist in a classifier during the continuous classification of bituminous coal, anthracite coal, and an iron ore trailing."

Jan 1, 1946

By W. Bruce Montgomery

Manganese oxides occur, with some iron oxides, in small scattered lenses on property controlled by the Columbia Manganese Co. (1943) near Evington, Campbell County, Va. The company mined some manganese ore during 1917 and 1918. A preliminary examination in May 1942 indicated the possibility of finding additional ore. On August 21, 1942, the Bureau of Mines began prospecting to verify the continuity of the ore exposures. Work on this project continued until February 5, 1943. Prospecting and development work included shaft sinking, crosscutting, drifting, trenching, and test-pitting in six separate areas indicating two types of deposits. The most predominant type is a wide brecciated area in which occur lenses or pockets of nodular manganese oxides. The other type is characterized by more of a vein structure, including thin layers of manganese oxides.

Jan 1, 1949

By N. F. LeJeune

For a number of years the Bureau of mines has conducted semi-annual surveys to determine the changes in the characteristics of the motor gasoline being sold in the United States. The Bureau of Mines surveys, from April, 1917, to January, 1943, indicated a progressive decrease in the end point range. The survey for July, 1923 showed an interruption in this progressive decrease. This interruption, as shown in Table 1, in the line marked "Difference," was apparently a definite one, for the data obtained in the surveys of July, 19233, January, 19244, and the present one, apparently substantiate it. The figures in Table 1 were obtained by averaging the end points of the least volatile and most volatile samples of gasoline. For example, of 850 samples analyzed in 1919, the 10 per cent (85 samples) having the highest end points and the 10 per cent having the lowest end points were grouped, and the end points of each group averaged. These averages are represented in the table as the "Maximum 10 per cent" and the ?Maximum 10 per cent," respectively. The same scheme was used on the succeeding surveys.

Jan 1, 1924

By Robert E. Hershey

1. The investigation shows that the Sewanee coal bed is the most important bed in Grundy County arid is the only bed that has had any sustained production. There is no production, at the present time, from any of the other coal beds in the county. The Richland (Lower Sewanee or Coke Oven) coal bed has been prospected but has never been developed extensively. The Angel coal bed has been worked to a very small extent near Beersheba Springs, Tenn., for local consumption. The Battle Creek coal bed has been worked sporadically near Monteagle, Tenn. 2. Known measured and indicated reserves in the Sewaneee coal bed, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 15 millon short tons as of January 1, 1953. Of this total, 10 million tons represents coal 28 inches and more thick. Areas in the bed were omitted from the estimate where available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By J. M. Stuve

Low-temperature adiabatic heat-capacity determinations were made by the Bureau of Mines in the temperature range from 5 to 300 K for the two crystalline modifications of zinc sulfide, sphalerite (ß) and wurtzite (a). The entropy at 298.15 K of sphalerite was evaluated as l4.02±0.04 cal/deg mole and wurtzite, l4.06±0.04 cal/deg mole.

Jan 1, 1974

By N. S. Dalal, V. Castranova, K. Van Dyke, V. Vallyathan

"IntroductionInhalation of crystalline silica is often associated with the development of pulmonary disease (Ziskind et al., 1976). Recently, it has been proposed that freshly sheared silica .may have surface properties that make it more reactive with lung tissue than aged silica, and that this unique reactivity ·of freshly crushed silica enhances its pathogenicity. A recent study in our laboratory strongly supports this theory (Vallyathan, et al., 1988a; 1988b). We found that grinding of silica cleaves bonds in a silica tetrahedral lattice generating reactive free radicals sites on the surface of the silica particles. The presence of surface radicals on freshly ground silica was monitored by electron spin resonance (ESR) spectroscopy. The ESR signal generated from fresh silica in air is characteristic of Si-0 and Si radicals. Evidence, i.e., the ESR signal after the addition of a spin trap (DMPO) and its sensitivity to ethanol, indicates that these silicon-based surface radicals can react with water to form hydroxyl radicals (OH). Results also indicate that these surface radicals make fresh silica more cytotoxic than aged silica; i.e., fresh silica causes more membrane damage as evidenced by hemolysis and lipid peroxidation. Therefore, the presence of reactive sites on the surface of freshly cleaved silica may play a significant role in its pathogenicity.If surface· free radicals are related to cytotoxicity, then screening dusts for the existence of such radicals may predict their relative pathogenicity. Since an ESR spectrometer is not available to many laboratories, the objective of this study was to develop a quick and simple technique to monitor the existence of reactive surface sites on dust. The technique chosen was the measurement of chemiluminescence using a liquid scintillation counter; i.e., an instrument which·would be accessible to most investigators."

Jan 1, 1989

By W. D. Bryson

This paper is one of a series being prepared by the United States Bureau of Mines on tunnel-driving methods. The practices described are those used at No. 11 mine of the Colony Coal Co., Denver, Colo. No. 11 Mine is situated at Dines, some 14 miles north of Rook Springs, in Sweetwater County, Wyo. It is served by a spur off the Winton branch of the Union Pacific Railroad. The Colony Coal Co.'s mines were opened in 1918, and since that time have been among the largest producers of coal for the railroad and domestic markets in the Rock Springs coal district.

Jan 1, 1932