Search Documents

By B. D. Sartwell

Multiple-charged beams originating from a 300-kv ion accelerator are important tools in the study of metal surfaces and thin films. A knowledge of the particle range is necessary for an understanding of the interaction processes of the ions with the targets. Utilizing a theory developed by Lindhard for determining the range of low-energy ions in solids, the ranges of H, He, C, N, 0, and Ar ions in A1203, Al, Fe203, Fe304, CuO, Cu20, Fe, Cu, Sn, and W were calculated for the energy range 60 to 400 kev using a computer program written in BASIC. The range, presented in graphical form, is given in both µg/cm2 and angstroms. In addition, heavy ion ranges were calculated for comparison with published experimental values. For ions with Z > 5, the discrepancy between the calculated values and published experimental values generally ranged from 2 to 40 percent; the largest deviations were probably due to experimental error.

Jan 1, 1970

By W. E. Miller, G. S. Scott, G. W. Jones

"INTRODUCTION One of the major activities of the Bureau of Mines is the promotion of safety in mining and the mineral industries. Research is undertaken in connection with these problems to determine the explosion and ignition hazards of combustible gases, liquids, and solids and to investigate means of reducing them.Occasionally the Bureau is asked to determine inflammability or ignition temperatures to enhance safety in nonrnineral industries. From time to time it has complied with such requests when no other agency was available to do the work and the investigation could be conducted with a minimum of time and expense. The present investigation is one of this class.Nicotine (C10H14N2), a colorless combustible liquid having a boiling point of 246°C, is usually obtained from tobacco and its products by extraction processes. When heated to its boiling point it decomposes; the purified product is obtained from tobacco extractions by distillation at reduced pressures or is distilled in a current of inert gas.It has an unpleasant odor, a burning taste, and in the undiluted state is highly toxic. Under certain conditions it can be oxidised to nicotinic acid and in the near future may therefore become of considerable economic importance. Nicotinic acid is a component of the vitamin B complex now commonly used to fortify white flour and other foods that normally are deficient in these vitamins."

May 1, 1942

By Robert M. Becker

A multistage probability model for assessing the reliability of mineral samples following any number of stages of sample reduction is presented. Sample reduction is the process of alternately crushing or grinding and sampling mineral particles prior to assaying. The final multistage model developed accurately describes the ideal sample reduction practice. This model is based on previously developed and experimentally tested models for a single stage of sampling. The problem is approached through the probability distributions for the various stages of sampling. The probability distribution, moments, and moment relationships for a single stage of sampling are first reviewed, and the useful concept of unit moments is defined. In presenting the models for two stages of sampling, emphasis is placed on the physical description of the sample reduction process which leads quite naturally to its mathematical representation. In this representation, crushing or particle-size reduction between the stages of sampling is viewed as a random process with respect to the number and proportion of particles of the various kinds produced. The physical and mathematical description is extended to more than two stages of sample reduction, and the first three moments for any number of stages are developed. In common sample reduction practice the effects of a finite population (finite amount of material) at each stage of sampling appear to be important in describing the variance contribution of each stage. This is also true for the third moment about the mean. An example is cited in which the skewness increases by more than an order of magnitude when several stages of sampling are considered. This is largely due to the dependence of the multistage third moment about the mean on the variance. In general the model and results should be useful in helping to understand, control, and reduce the random errors that arise in the sample reduction process.

Jan 1, 1968

By A. L. Engel

Many western ores containing ;old, silver, and copper can be mined and concentrated at a profit only when the recovery of those metals is high and treatment costs are low. Usually, ores containing easily dissolved copper minerals, or copper minerals that become soluble to some extent through oxidation during treatment, present a real problem in cyanidation. Copper cyanide compounds are formed that tend to 'precipitate and that cannot yield regenerated cyanide and metallic copper on contact with zinc. This results not only in some loss of copper through solution in cyanide, but in excessive consumption of cyanide above the amount required for the extraction of Gold and silver. Any moans, therefore, of minimizing the: loss of cyanide while at the same time effecting high recoveries of the several values contained in the ore is of wide interest. A sample of typical low-grade ore of gold, silver, and copper, containing copper-sulfide minerals, was obtained from the MacLaren Gold Mines Co., Cooke, Park County, Mont., for laboratory investigation by flotation and cyanidation.

Jan 1, 1950

By William O. Vanderburg

This paper describing the practice at the Wolf Pongee concentrator at Federland, Colo., is one of a series on similar subjects being published by the United States Bureau of Mines. The author acknowledges the assistance of Loach, manager of the Wolf Tongue Mining Co., and of W. G. Roseborough, superintendent of the golf Tongue mill, in the preparation of this paper.

Jan 1, 1933

By Jr. Hardy, H. Warren Shen

"A study is presently underway by the authors to investigate the character of the bit-coal interaction during coal cutting and its influence on the size and shape distributions of the generated dust. An important aspect of this on-going project is the development of acoustic emission (AE) criteria which would make it possible to carry out remote monitoring of coal cutting operations. The on-going AE studies are fundamental in form and were undertaken to evaluate the general feasibility of AE monitoring techniques using simplified coal breakage and cutting procedures. The present paper will focus on the test facilities, experimental techniques, and results associated with linear, single-bit cutting. An AE-transducer, attached directly to the bit, detected AE signals during the cutting process.Experiments have been carried out on seven specimens of coal obtained from the USBM experimental mine at Bruceton, Pennsylvania. Three separate cuts were made for each of two bit angles (10 and 45 degrees) and two bit velocities (0.085 and 0.169 cm/sec), for a total of 12 separate cuts. Data associated with resulting particle size distribution and AE characteristics (major dominant frequency components) will be discussed. Data analysis has also been underway using a computer-based pattern recognition system known as ICEPAK (Intelligent Classifier Engineering Package). This program is able to evaluate over 100 features of an AE event and to make objective comparisons between AE signals associated with different loading or cutting parameters. The results to date show that AE generated during some of the test conditions can be recognized by ICEPAK with a recognition rate of 90% and higher while other conditions cannot at present be separated with a suitable recognition rate. Further analysis of the experimental data is presently underway.The reduction of the severity, and eventual elimination, of Coal Workers' Pneumoconiosis (CWP) depends on gaining fundamental understanding in a number of major areas. These include dust generation and entrainment, transportation, suppression, medical effects of dust, and possible treatment. At present a project is underway by the authors to investigate the character of the bit-coal interaction during coal cutting and its influence on the size and shape distributions of the generated dust. An important aspect of this on-going project is the development of acoustic emission (AE) criteria which would make it possible to carry out remote monitoring of coal cutting operations. Suitable on-line analysis of monitored AE data would allow engineers to evaluate factors such as shearer bit conditions and cutting efficiency, and to quantify the particle size and shape distribution of the generateddust. The on-going AE studies are fundamental in form and were undertaken to evaluate the general feasibility of AE monitoring techniques using simplified coal cutting procedures. To date experiments have been carried out on coal under uniaxial compression, linear single-bit cutting, and cutting using a laboratory-scale, single-bit shearer. A brief outline of the overall study has been presented in an earlier paper (Hardy, Shen and Kimble, 1995). This paper will consider the linear single-bit cutting studies in more detail.It is generally accepted today that most solids emit low-level seismic signals when they are stressed or deformed. In this paper this phenomenon will be referred to as acoustic emission (Hardy 1972, 1981, 1989). In essence, the measurement of AE activity in a field or laboratory structure is relatively simple. A suitable transducer is attached to the structure, the output of the transducer is connected to an associated monitoring system, and the AE signals occurring in the structure, due to internal or external stress, deformation, and failure are suitably acquired, pre¬processed and recorded."

Jan 1, 1998

By A. L. Murray, C. A. Allen

"In the Spring of 1919, the Industrial Commission of Utah undertook the assembling of safety orders covering metal mining operations Just at that time there appeared several articles in the mining papers advocating the licensing of hoisting engineers, so this subject was given careful consideration,The licensing of hoisting engineers means that they must pass an examination covering the mechanical features of hoists and boilers, and must have a certain amount of experience. This undoubtedly serves to get a class of hoisting engineers that are better informed about the mechanical operation and theoretical considerations in hoisting and the only room for argument against it is that it is difficult to give an examination that will determine whether or not a man is a competent hoisting engineer.A man might pass an excellent examination yet be absolutely unqualified to operate a hoist and the judgment of the mine super- intelligent would have to be depended upon to choose the right man from among those who were licensed. This difficulty of properly determining, by ordinary examination, a man's qualifications to run a hoist caused the idea of licensing' in the ordinary sense of the word to be abandoned; but, as there was no question that a hoisting engineer should be physically fit, it was decided to require a medical examination, and at the same time to require the hoist engineer to state his experience, so the State would better knowledge of his general qualifications.The orders covering the question were therefore issued as follows;"

Jan 1, 1920

By Je M. Oh

The Bureau of Mines is conducting research to determine the high temperature oxidation resistance of substitute stainless steels (SS) containing two less strategic elements, Al and Si, instead of Cr. Chromium is considered to be a critical and strategic metal. Although the Cr content was reduced to 8 wt pct, the alloys showed better oxidation resistance than did 304 SS containing 18 wt pct Cr. Specifically, the alloys that contained Fe-8Cr-16Ni with combinations of Al and Si showed excellent oxidation resistance even at temperatures up to 1,000° C. In this study, the effects of the alloying elements on oxidation kinetics and morphology of oxides were investigated using a Cahn Rg electrobalance, scanning electron microscopy, an energy-dispersive X-ray analyzer, X-ray diffraction, and an electron microprobe. Aluminum and silicon additions in combinatin were more effective in providing oxidation resistance than either element was alone.

Jan 1, 1986

By R. V. Ramani, R. Bhaskar

"An airborne dust cloud is an ensemble of particles of varied size, density, shape and states of aggregation. An understanding and quantifying of the dispersion and deposition of the dust generated in mines is essential to the development of measures for reducing worker exposure to dust. In coal mining, the major portion of the dust is generated during the cutting of coal using a shearer or a continuous miner.The major phenomenon affecting ambient concentration is the deposition of dust. Particle deposition may take place due to the effect of gravitational, inertial, electrostatic, and thermal forces, and mechanisms such as Brownian and eddy diffusion and inertial impaction, The three major mechanisms of deposition in turbulent flow in mines are diffusion (Brownian and eddy), sedimentation and inertial impaction. The mechanisms determining particle deposition are size depend,From a review of the literature, there appears to be a knowledge gap in the understanding of the deposition phenomena in mine airways. In order to obtain a better understanding of the deposition of dust for various particle sizes, and to develop a set of data for evaluating predictive mathematical models for dust-flow in mines, a series of dust flow experiments was performed under controlled conditions in mine airways. It appears that the deposition data generally follow the theoretical behavior of dust based on the combined effect of diffusional and gravitational deposition. In this paper, the findings of the study on the deposition of dust in mine airways and its dependence on size, velocity and concentration are discussed. A set of deposition equations that could be used to determine the approximate deposition at various points in a mine airway are presented.The major factor affecting ambient dust concentration in mine airways is the deposition of dust. Particle deposition may take place due to the effect of gravitational, inertial, electrostatic, and thermal forces, and mechanisms such as Brownian diffusion, eddy diffusion and inertial impaction. The major mechanisms of deposition in turbulent flow in mines are diffusion (Brownian and eddy), sedimentation and inertial impaction. Inertial impaction is significant only during changes in direction, but the change in direction of flow with resultant powerful eddies may cause increased re-entrainment of the particles, thus having a compensating effect. While the literature in aerosol sciences contain several references on deposition, most studies were done in small diameter tubes for diffusional deposition (Liu and Agarwal, 1974). The deposition data from small diameter, short tube experiments may not be applicable to studying deposition in mine airways that have large areas and extend several hundred meters. Further, the change in concentration along the length of a mine airway may significantly affect the deposition, an aspect that may not be easily determined in short tubes in laboratory experiments."

Mar 1, 1992

By F. F. Hintze

In the group of minerals used in making this study, the cyanite is associated with quartz, mica, and feldspar in the schist. The amount of quartz is variable, but it is always an abundant mineral. Both large and small crystals of quartz occur in irregular masses, rarely ever showing crystal outline. Mica Is of the clear and dark varieties, the larger crystals being dark as a rule, and the finer crystals of light color. The present mineralogical composition of the mina is rather variable, as most of the original biotite and muscovite have suffered alteration, and much secondary mica is present as a result of alteration of the original mica and other minerals present, especially the larger cyanite crystals. A large part of the mica now found in the ore is chlorite, with varying amounts of Jefferisite and others, especially sericite. These are in the form of aggregates, or felt-like intergrowths filling the spaces between the quartz, cyanite, and feldspar. The feldspar is plagioclase probably mostly albite. It is white, possesses good cleavage, and is one of the hard brittle minerals of the rock. It alters to kaolin, and sericite, and more or less of these alteration minerals are present within the feldspar crystals but not separated from them. The cyanite is of two varieties, distinguished by their colors as blue and white cyanite. The blue color varies in intensity, being a pronounced blue in some crystals and paler in shade in others. Some crystals have been seen which posses the blue color in one-half of their mass and are pure white or clear in the other half. The purity of the cyanite is probably not affected by the color, but it is difficult to detect the white cyanite in the ore by macroscopic examination, so that great care has to be exercised in the selection of the ore in the field. Of the above minerals, cyanite is the heaviest, having a specific gravity of 3.6; none of the others approach it in specific gravity. The usual as opiates of cyanite in the mica schists are garnet, magnetite, and tourmaline, but these have not been noted in the group of minerals treated, and their absence is a point of great value in favor of this ore, as they possess high specific gravities and interfere in separation processes, and if not separated they are detrimental because of their easily fusible character. Small amounts of apatite and titanite have been noted, but not enough to cause trouble.

Jan 1, 1931

By Thomas E. Marshall, Patrick A. Kinek, Gerald L. Finfinger

The purpose of this investigation was to evaluate the integrity of the existing shutoff valves and actuators used under high-temperature conditions in the Bureau of Mines' horizontal borehole methane drainage pipe- line system and to determine the potential for improvement in the system. In the field tests, both fire-safe ball valves and standard brass ball valves were initially subjected to a 30-min pan fire without thermal protection. Neither valve could maintain line pressure beyond 11 min in a fire that reached temperatures between 500° and 700° C. Based on the test results, it was concluded that the brass ball valve used in the Bureau's methane drainage pipeline system can be retrofitted with an inexpensive "fire bag" to substantially increase its integrity under mine fire conditions.

Jan 1, 1986

By L. C. IlsLey

The service given by a flame safety lame is twofold: It provides a safe light and it gives evidence of the condition of the mine atmosphere relative to the presence of methane and the deficiency of oxygen. Since the development of portable electric mine lamps, flame safety lamps are little used for lighting,but their use as detectors is as extensive and important as ever. A flame safety lamp in the hands of a trained user will definitely how methane concentrations as low as 1 percent, which in well below the lower explosive limit of methane and air. However, this does not always suffice, especially when making studies of mine ventilation, where it may be desireable to detect concentrations below 1/2 of 1 percent.

Jan 1, 1936

By L. C. IlsLey

[The service given by a flame safety lame is twofold: It provides a safe light and it gives evidence of the condition of the mine atmosphere relative to the presence of methane and the deficiency of oxygen. Since the development of portable electric mine lamps, flame safety lamps are little used for lighting but their use as detectors is as extensive and important as ever. A flame safety lamp in the hands of a trained user will definitely show methane concentrations as low as 1 percent, which in well below the lower explosive limit of methane and air. However, this does not always suffice, especially when making studies of mine ventilation, where it may be desireable to detect concentrations below 1/2 of 1 percent.]

Jan 1, 1936

By Frank E. Cash, Max S. Petersen

"INTRODUCTION Explosives have been used in ever—increasing amounts since gunpowder was invented. For hundreds of years only low explosives of the deflagrating type were used, and they were fired by means of a flame or hot object. Ben¬jamin Franklin first ignited gunpowder from a distance in 1751 by means of an electrostatic spark. Further efforts to develop a satisfactory electrical method to ignite explosives from greater distances were overshadowed by the invention of safety fuse in 1831, as this offered a relatively simple and inexpensive means of firing explosives.The discovery and introduction of high explosives of the detonating type and the invention of the fulmitate of mercury blasting cap about the middle of the nineteenth century provided the needed impetus for inventors to develop means of firing the cap by electricity. The original high-tension igniter, following Benjamin Franklin's experiment in which the detonating compound was ignited by a spark, was discarded in favor of a low-tension igniter, in which the detonating compound was ignited by a heated wire. The past 2 decades have seen considerable improvement in the design and construction of electric detonators to make them safer and more efficient, yet in spite of the improvement it is estimated that less than 50 percent of the explosives used in industry today are ignited or detonated electrically. The trend, however, is toward the use of electric methods. In recent years numerous-mining companies have introduced electric blasting exclusively at their mines as a means of improving safety and efficiency."

Sep 1, 1946

By R. L. Schmidt

The Methane Control and the Respirable Dust Groups at the Twin Cities Mining Research Center (TCMRC) cooperated recently in obtaining production samples of approximately 1 ton each, from the loading conveyors of a ripper, a borer, and a loading machine in conventional development headings. These samples were sized, in four stages, from plus 4 in to minus 10 µm. The conventional product had the least fines of the three production methods. The borer product had more fines than did the ripper product, but it also had a greater amount of large pieces. All three products, as sampled, had essentially the same amount of minus 10-µm particles. Photomicrographs and surface?-area comparisons were made. Gas -adsorption, surface-area determinations on particles under 37 µm give essentially the same value. Surface-area calculations, assuming spherical particles and no porosity, give a smaller area to the conventional product.

Jan 1, 1972

By M. G. Pelipetz

High-pressure, high-temperature hydrogenation of coal has been known and practiced for many years. A full' understanding of the mechanism in this process by which coal is converted to oil and gas must rest on a critical interpretation of the manner in which external variables influence the rate and the course of the coal-hydrogenation reactions. Same Bureau of Mines studies on the effect of temperature, catalyst, and rank of coal on these reactions have been published. The effect of pressure was not studied in this earlier work, and the effect of reaction time was complicated by the interruption of long reaction periods in order to refill the autoclave with hydrogen. It is the purpose of this paper to present data from more recent autoclave experiments that extend the results of Storch, et al, on the kinetics of coal hydrogenation. These data must be explained by any comprehensive theory of coal hydrogenation; their detailed evaluation, however, will be deferred until a later publication.

Jan 1, 1949

By D. A. O'Keefe, M. M. Wong

To obtain beryllium metal of higher purity , flakes produced from electrorefining scrap metal were used as cell feed for a second cycle of electrore fining at 500 ° C in an electrolyte composed of 51.7 mole - percent LiCl , 36.9 molepercent KC1 , and 11.4 mole - percent BeC¹ · Metallic impurities in the flakes totaled more than 108 ppm , the metallic impurities in the metal obtained from the two - cycle electrorefining were , with the exception of 35 ppm of calcium , below the spectrographic determination limits .

Jan 1, 1964

By Kevin A. Rider, Bernard J. Martin

Reaching movements are planned and subsequently executed [1] using visual and somatosensory feedbacks [2], where absence of visual feedback is known to increase endpoint variability [3]. Visual occlusion decreases the ability to make rapid online compensatory movements, which results in initial radial deviations that are highly correlated with radial dispersion at the target. Perturbations of rapid, visually-guided reaches are compensated on-line and result in endpoint dispersions poorly correlated with initial deviations, emphasizing the strong effect of visual feedback in temporally-constrained reaching tasks. In control conditions (no vibration), these uncompensated, rapid reaches serve as estimates of the individual’s intended trajectory. When ride motion is present, trajectories of rapid, visually-occluded reaches provide a measure of the natural biodynamic response of the cantilevered spine-arm-hand linkage. These intended movement trajectories and the biodynamic response (vibration feedthrough) are used to predict the effect of ride motion on the performance of rapid reaching tasks. Goals of this study are to investigate the influences of vehicle motion on human reaching and pointing, and to reveal movement strategies used in visually-occluded reaching tasks. Methods A six degree of freedom human-rated Ride Motion Simulator (RMS) was used to generate a dynamic vehicle environment. Participants performed discrete, rapid pointing tasks to targets presented on three touchpanel displays under stationary and random whole-body vibration. Reach instructions included successfully reaching identical circular targets (Ø = 0.25”) with the right index fingertip as fast as possible. Targets were presented on resistive-touch displays mounted approximately 60 cm from the participant’s nasion. The touchpanel displays were located in the forward and lateral directions at eye level, and forward at 45° of elevation. These displays measured the spatial error of the reach destination. A ten-camera VICON motion capture system recorded the upper body kinematics of the participant. Reflective markers were placed on the participant’s torso, head, and arms. Initial kinematics of the fingertip (i.e. time and magnitude peak tangential velocity) and tangential velocity at target were used to estimate the planned endpoint of the reach. Results and Discussion Ride motion resulted in increased endpoint variability compared to reaches performed in the stationary condition. Reaches to the elevated touchpanel consistently resulted in the largest variability across all motion conditions, suggesting that a vehicle occupant would not be capable of accurately activating a control in that location. Principal axes of endpoint ellipses were along and perpendicular to the direction of fingertip movements. Example graphs of endpoint variability with ellipses containing 95% of the data points are shown in Figure 1. These ellipses

Jan 6, 2006

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

CALCULATION OF MINE HEAD LOSSES FROM ALTIMETER SURVEY DATA USBM PENNSYLVANIA STATE UNIVERSITY - MINERAL ENGINEERING DEPARTMENT USBM USBM USBM THIS PROGRAM CALCULATES PRESSURE LOSSES USING THE USBM METHOD GIVEN USBM IN USBH IC 7809 BY MCELROY AND KINGERY.1957. THE MAJOR DIFFERENCE USBM BETWEEN THIS PROGRAM AND THE CITED REFERENCE IS THE TREATMENT OF AIR USBM

Jan 1, 1977

By C. W. Davis

Before listing the laboratories and the work performed there, it is proper to make clear what is done and what is not done by Federal bureaus, States, and Territories, as well as by countries to the north and south of the United States. FEDERAL Bureau of Mines. - The Bureau of Mines does not make assays or analyses for individuals or firms unless the samples are part of the ore-testing and ore-dressing investigations of the Metallurgical Division on representative ores from mining districts and of possible benefit to the entire mineral industry through published reports. All significant results obtained in this way are made public. Any mineral sample sent to this Bureau for simple identification will be examined.

Jan 1, 1938