Search Documents

By John C. Edwards

A computer code for laminar, steady-state, incompressible, two-dimensional flow developed by Gosman (2)3 was modified by the Bureau of Mines to calculate shock (minor) loss at the intersections of ventilation ducts. Turbulent flow was simulated using laminar flow equations and an appropriate wall shear stress. Results of the calculation showed good agreement with the experiment.

Jan 1, 1977

By J. Wade Watkins

One potential peaceful application of nuclear explosives is stimulating the production of liquid or gaseous hydrocarbons from essentially nonproductive deposits of petroleum, natural gas, oil shale, and tar sands. Within the United States the appreciable difference between producible proved reserves and ultimate reserves and resources of hydrocarbon deposits is of such magnitude that much petroleum, natural gas, shale oil, and bitumen will not be produced unless significant technological progress is made in production techniques. The shattering effect of contained nuclear explosives and, to a lesser extent, the heat produced, have been considered as stimulative forces when the thickness, depth, and nature of such deposits permit considering the use of nuclear devices. Mechanical production problems would be less in an oil or gas reservoir than in an oil-shale or tar-sands deposit. Also, tar-sands resources in the United States may not be adequate to warrant serious consideration of applying nuclear-explosives stimulation. Gas reservoirs should present the least- radioactive-contamination problem. The technical feasibility of using nuclear explosives cannot be evaluated fully at present. Additional information is needed on the effects of pressure, heat, and radioactivity on the solids and fluids of hydrocarbon deposits, the nature and extent of induced fractures in different rock media, and the possibility of isolating and confining or removing radioactive contaminants. Final technical feasibility can only be determined by a field test. If technical feasibility is established, economic feasibility will depend upon the comparative cost of producing hydrocarbons by nuclear explosives and by conventional means. It is probable that an economic comparison would favor nuclear stimulation only where devices of relatively high yield could be used practicably and safely.

Jan 1, 1964

By R. L. Grant

"Carbon dioxide has been used for extinguishing electrical fires of many kinds (1, 3, 4) 3/ and more recently has been applied to some extent in fighting coal-mine fires (5). This report is concerned with the possibility of an electric current being conducted from a live power source, such as a trolley wire, across the impinging spray of carbon dioxide gas, to a metallic discharge nozzle, and then being grounded through the body of the person holding or touching the container. Rose and. Skinner (5) have described a case in which a fall of roof coal had brought down the trolley without creating a dead shot. The current was conducted in part through the loose coal to the rail, causing ignition of the coal. The fire was successfully extinguished with carbon dioxide.Dielectric data on pure carbon dioxide gas and liquid have been reported by Quinn and Jones (2). For the gas, the dielectric constants range from 1.00971 (35°C., 10 atmospheres) to 1.3072 (70°C., 151 atmospheres); for the liquid, 1.6016 (0°C., 50 atmospheres). Compared with the dielectric constant of air (1.0006, 1 atmosphere), these data, indicate that carbon dioxide in both gaseous and liquid forms is a very poor conductor of electricity, of the same order as air. 4/"

Aug 1, 1942

By C. E. Reistle

[In producing crude oils of paraffin base and of mixed base the producer is often confronted with the problem of preventing and removing paraffin that settles out of oil and accumulates in the well. This paraffin consists of heavy waxes with some sand and asphalt, and varies in. consistency from a soft semifluid wax to hard gummy wax. This problem is by no means a new one as troubles have been encountered with it since the earliest days of the industry. However, with the discovery of the panhandle, Texas, field and other large fields in which extensive troubles have been encountered, the problem has assumed added importance. In new fields the most serious trouble with paraffin is in the flowing wells the paraffin accumulates in the casing and tubing of such wells and unless removed will completely plug the well. This condition also develops in wells which are produced by gas lift, and often presents a serious problem when, this method of producing the oil is used. In older fields paraffin is also deposited on the face of the producing sand that on the walls of the hale or within the interstices of the sand near the hole, and this materially affects the amount of oil that can enter the well.]

Jan 1, 1927

By Laurance L. Oden

The Bureau of Mines conducted corrosion tests of 18 commercial alloys in H3 P04 -phosphate rock or A1,03 slurry, in 10 pct HF, and in 25 pct H2 SiF6 to simulate three environments anticipated in a Bureau process to extract fluoride values from phosphate rock. Small alloy coupons were rotated in duplicate tests at 4.4 to 21 fps in the slurry at 170° C to determine rates of erosion-corrosion. At 4.4 fps the lowest rates, in mils penetration per year (mpy), were measured for Hastelloy C-276 (<20), Hastelloy B (30), and Inconel 625 (150);the rates increased at 21 fps to 55 mpy, 45 mpy, and 1,000 mpy, respectively. The corrosion rate for all alloys exceeded 40 mpy in either the equilibrium vapor or liquid phases of aqueous solutions containing 10 pct HF or 25 pct H2SiF6 at 100° C. Uniform corrosion in 10 pct HF at 50° C was observed only for Inconel 625 (22 mpy), Hastelloy C-276 (43 mpy), and Illium 98 (17 mpy). Inconel 625 (0.75 mpy), Hastelloy C-276 (1.3 mpy), Illium 98 (1.7 mpy), and Incoloy 825 (0.45 mpy) were attacked uniformly in 25 pct H2SiF6 at 50° C.

Jan 1, 1974

By Wilbert J. Huff

For the past 8 years the technical studies conducted by. the Explo- sives Division of this Bureau have been summarized in a series of annual reports.3 This report deals with activities from July 1, 1942, to June 30; 1943. Specific problems have been in immediate charge of section or unit leaders, to whom credit is given.

Feb 1, 1944

Develop technology for preparing thick corrosion-resistant coatings and electroforms of iron-chromium-nickel alloys. Approach To reduce the United States&apos; dependence upon foreign sources for supplies of strategic and critical metals such as chromium, cobalt, and nickel, new technology must be devised to conserve these valuable commodities. One approach being investigated by the Bureau of Mines is the use of a modified-aqueous-electrodeposition method to prepare thick (-25 µm), complex alloy coatings (e.g., stainless steel composition) with properties similar to the commercial alloys. An alloy coating on a low-alloy steel or carbon steel substrate would require significantly less strategic and critical metals than those contained in an equivalent mass of the commercial alloy. Coatings applied to appropriate mandrel materials make possible the preparation of intricately-shaped alloy electroforms (near-net-shape parts). As a result, the loss of valuable metals associated with machining finished products would be minimized.

Jan 1, 1986

By J. B. Gayle

Because economic and geographic factors have focused particular attention on the use of anthrafines in blends containing Lower Kittanning coal as the low-volatile component, samples from this particular bed were selected for experimentation whenever practical. Carbonizing tests were carried out in accordance with standard procedures, using the Tuscaloosa and sole-heated ovens. Most of the results are in general agreement with those reported by previous investigators. Specific findings are as follows: (1) The effectiveness of anthrafines in reducing coal expansion is such that even highly expanding, low-volatile coals can be carbonized safely with suitable additions of anthrafines and careful control of charge density. (2) Increases in coke size, resistance to shatter, and apparent specific gravity appear to be characteristic for additions up to approximately 15 percent to a fixed base blend. When anthracite of minus-48-mesh size was used and the proportion of low-volatile coal simultaneously increased, these indexes increased only slightly or remained substantially constant. (3) No increase in breeze formation was noted for additions in amounts up to 15 percent. (4) Abradability of coke was increased by additions of anthracite of No. 5 Buckwheat size, but it either decreased or remained sub¬stantially constant when the inert was ground to pass a 48-mesh screen.

Jan 1, 1956

Improve the performance of waterjet nozzles used for water-jet-assisted cutting to optimize rock cutting efficiency. Approach The performance of a longwall shearer equipped for water-jet-assisted cutting was evaluated during an earlier study (Tech News No. 277). Waterjet nozzles were used to direct the solid streams of water that impacted the rock near the tip bits. The maximum water pressure that could be delivered to the nozzles was about 6,000 psi. Due to the "break up" of the solid stream of water, some of this pressure was lost before the water reached the rock. The pressure could have been increased by moving the nozzle closer to the bit tip but) moving the nozzle too close increases the possibility of damage to the nozzle. Study Results A test apparatus was built to measure water pressure at the location of water jet impact (see illustration). The target, a tungsten carbide plate with a 0.013 inch diameter orifice, was placed at the location of water jet impact. A pressure transducer, used to monitor impact water pressure, was positioned under the plate. Water pressure at the nozzle was maintained at 6,000 psi. The distance between the nozzle and target was varied from 2 to 5 inches.

Jan 1, 1988

Develop new technolgies and techniques which enable recovery of strategic and critical minerals such as cobalt from domestic resources, thereby easing the U.S. dependence upon foreign producers for these valuable commodities. Approach The Bureau of Mines, through research, developed a process which uses mineral beneficiation techniques to recover cobalt-rich products from Missouri lead ores. Before development of this process, cobalt was lost as an impurity in the copper, lead, and zinc concentrates and in the mill tailings because the technology to recover it with minimum impact on present production did not exist.

Jan 1, 1989

By Charles H. Shapiro

[In July, 1924, the Bureau of Mines, through its Petroleum Experiment Station, undertook a field study of methods used in oil-field shops for dressing and tempering fishtail bits. The purpose of this work was to suggest chances that would be helpful to the bit-dresser in turning out better treated, harder, and tougher bits, and thus cut down the excessive loss of time caused by too frequent changing of bits. It was the intention to eliminate as much as possible the guess work connected with dressing and tempering bits under the method of judging temperature by eye, by developing; practical methods of controlling temperature. If there were some possible means of accurate temperature control, then it would be an easy matter to bring all bits to the proper temperature for maximum hardness rued toughness, thus doing away with the source of most of the trouble experienced in the present method of bit tempering. Shortly after the Bureau of Mines began its study, a chop In the Stroud, Oklahoma, oil field announced method for tempering fishtail bits that Would increase the drilling footage of each bit treated. The method accurately regulates, by the use of a bath of molten salt, the temperature to which a bit is heated before being quenched to produce hardness. There is nothing new in using silt baths for the, heat treatment of steel, but this was the first attempt to introduce it into the oil fields for use in hardening bits, and for this purpose it proved to be admirably adapted. In tempering, by the old system it is not possible to measure the temperature of the heated bit by means of an electrical instrument for that purpose, whereas this is an easy matter with the now method. If heating steel to slightly above the critical point rind quenching suddenly will bring out its best properties, their here is a method of accurately bringing the steel to that point.]

Jan 1, 1925

To determine the relative permeability of the soil a series of percolation tests were performed at the three locations of interest at Lanse, i.e., 3C, 03A and strip bank, and KA and KB at Kato. Soil cores were removed to 2, 8, 16, 24 and 32 inch depths with the thin wall sampler tube, each core separated from the next by about fifteen feet. Then two-foot-long thin-wall tubes were inserted into the 2, 8, and 16 inch deep holes and three-foot long tubes were inserted into the 24 and 36 inch deep holes. Each tube was tamped down about one inch further to assure a bottom seal; the tubes were filled with water and the rate of fall was measured. The test is similar to those done for septic tank percolation studies 6; but is not quantitatively related to Darcy&apos;s coefficient of hydraulic conductivity because the water can flow in three dimensions from the bottom of the tube. The measurements are dependent on the length of test, since the rate of fall is a function of the head. Therefore, it should be noted that the 24 and 32 inch deep tubes should give faster percolation rates because of the one foot greater head. At locations 03A and 3C the data show a sharp decrease in percolation at increasing depth, Table XV. However, the percolation at 03A and 32 inch depth is much higher than at 3C (0.2 vs. 0.01 inches/hour); the fragipan layer must be deeper at the 3C location since this area does experience a perched water table. On the strip bank the rates of falling head are randomly variable, appearing to be as much dependent on the particular location of insertion as on depth of placement. For example, water drained from the 16 inch tube as fast as it was added, probably into a sub-surface cavity or crevice. At Kato the tubes were more difficult to place because of interference of tree roots. For this reason 2 inch deep tubes were not inserted. These short tests at Kato were inconclusive, varying extensively when the tubes were moved. Field permeability tests were also performed in two (previously described) eight-inch diameter permeater tubes at Lanse and one at Kato. Because the soil is confined inside the tube, hydraulic conductivity can be calculated according to Darcy&apos;s flow equation. The high values reported in Table XVI experienced when the tubes were rewetted from a dry surface condition, enable us to conclude that infiltration is faster than the saturated permeability of the soil. In contrast to the falling head percolation tests, these permeability results do not show a high variation between locations.

Jan 1, 1972

By A. L. Murray, D. Harrington

From 1870 to the end of 1929 the coal production of Utah has been some- what less than 110,000,000 tons. During this period at least three major disasters have occurred with fatalities totaling about 380, establishing a decidedly bad record of approximately 3.5 persons killed by major mine explo- sions per million tons of coal produced. Even during the period when there have been no disasters, such as the years 1914 to 1920, inclusive, the fatalities in ordinary working were about 5.4 per million tons produced, against 3.7 per million tons for the whole United States for the same years. The 5-year period following the World War, 1918 to 1922, inclusive, had 4.7 fatalities per million tons; hence, the fatality record in the coal mines of Utah has uniformly been in excess of the average of the coal mines of the entire country. Notwithstanding this poor record, Utah has given to the coal-mining world many excellent safety methods and practices, and Utah coal mines in general take greater measures toward safe mining than do the coal mines of any other State; if practices and methods allowed and pursued in coal mines of other States were tried in Utah coal mines, there would be a succession of disasters.

Nov 1, 1931

By Joseph A. Sutton

The prospect of utilizing bacteria in mining and metallurgical processes introduces a new and challenging area of investigation. Elements of bacteriology and metallurgy are discussed in connection with possible areas where biological science might be applied in extractive metallurgy. Bacteria may prove important in the selective separation of metals from ores and metallurgical solutions, the production of sulfur from gypsum or pyrites, and the production of sulfuric acid from elemental sulfur. A series of reports concerning the experimental applications of bacteria on minerals and metallic ores will follow this paper. For several years the Bureau of Mines has been investigating the action of bacteria in the oxidation of sulfide minerals and their potential uses in metallurgical processes. Primary attention has been given to the possible utilization of certain strains of autotrophic bacteria that live in industrial leaching solutions or fractures of mineral outcrops. The purpose of this paper is to acquaint the mining and metallurgical engineer with micro-organisms and some of their possible applications in the field of extractive metallurgy.

Jan 1, 1961

By J. Wade Watkins

One potential peaceful application of nuclear explosives is stimulating the production of liquid or gaseous hydrocarbons from essentially nonproductive deposits of petroleum, natural gas, oil shale, and tar sands. Within the United States the appreciable difference between producible proved reserves and ultimate reserves and resources of hydrocarbon deposits is of such magnitude that much petroleum, natural gas, shale oil, and bitumen will not be produced unless significant technological progress is made in production techniques. The shattering effect of contained nuclear explosives and, to a lesser extent, the heat produced, have been considered as stimulative forces when the thickness, depth, and nature of such deposits permit considering the use of nuclear devices. Mechanical production problems would be less in an oil or gas reservoir than in an oil-shale or tar-sands deposit. Also, tar-sands resources in the United States may not be adequate to warrant serious consideration of applying nuclear-explosives stimulation. Gas reservoirs should present the least-radioactive-contamination problem. The technical feasibility of using nuclear explosives cannot be evaluated fully at present. Additional information is needed on the effects of pressure, heat, and radioactivity on the solids and fluids of hydrocarbon deposits, the nature and extent of induced fractures in different rock media, and the possibility of isolating and confining or removing radioactive contaminants. Final technical feasibility can only be determined by a field test. If technical feasibility is established, economic feasibility will depend upon the comparative cost of producing hydrocarbons by nuclear explosives and by conventional means. It is probable that an economic comparison would favor nuclear stimulation only where devices of relatively high yield could be used practicably and safely.

Jan 1, 1964

By A. B. Hooker, R. A. Kearns

Material used for flame safety lamp gauzes should possess the following qualities: (1) mechanical strength, (2) resistance to corrosion under service con- ditions, (3) a relatively high thermal conductivity, (4) a melting point above the ignition temperature of mine gas. Heretofore, three metals have been used for flame lamp gauzes, namely: steel, brass and copper. While each of these has the requisite qualities to some extent, none of them is an ideal gauze material. Copper gauzes lack mechanical strength, especiall, after they have been heated; brass and copper both have comparatively low melting points so that before the gas ignition is reached the gauze metal is attacked and oxidized under the action of the heat. Steel corrodes readily in damp atmos- pheres and if the lamp stands unused under these conditions for some time, the gauzes become unfit for service. Tests of these three materials have shown that steel offers the highest degree of safety. Manel metal, the natural alloy of nickel and copper, is practically noncor- rodible. Its relting point is approximately the same as that of steel. From time to time it has been suggested that this alloy might be a better gauze material than steel, since gauzes made of Monel metal should have all of the good qualities that steel gauzes possess and, in addition, would not corrode appreciably in ordinary mine atmospheres. One advocate of this use for Monel metal, the International Nickel Co., through their development engineer, Mr. Robert J. McKay, cooperated with the Interior Department, Bureau of ines, to the extent of supplying twelve sets of 30 mesh, Monel-metal gauzes for tests. Those gauzes were made up by the same lamp manufactur- er ho rade the steel gauzes used in the previous investigation. Being made by the same processes as the steel gauzes, these Manel-metal gauzes were needlessly given the same anti-rust coating that is always applied to steel gauzes to prevent any corrosion before the gauzes are used. In previous tests the Bureau of Mines had collected data as to the behavior of steel gauzes. In determining the value of Monel metal as a gauze material, it was planned to obtain similar data with Monel-metal gauzes, and thus make a direct comparison with the steel gauzes. In addition, steel and Monel-metal gauzes

Apr 1, 1923

By Motohisa Kanda

The time and amplitude statistics necessary to adequately describe electromagnetic (EM) noise in mines are illustrated through computer software techniques. They are 1) Allan Variance Analyses (AVA), 2) Interpulse Spacing Distributions (ISD), 3) Pulse Duration Distributions (PDD), 4) Average Crossing Rates (ACR) , and 5) Amplitude Probability Distributions (APD) . These statistics are illustrated using data taken from a rather large store of raw analog data recorded in operational mines. The curves generated for the illustrations characterize the noise environment in the mines from which the corresponding data were taken, and should aid in the design of reliable communication systems for such mines.

To develop a simple device for rapidly determining the shearing strength and angle of Internal friction of coal and rock in situ. Approach Use a portable, permissible, hydraulically operated device in boreholes as deep as 100 feet into the rib, floor, or roof of the mine. How it Works The device, called a Borehole Shear Strength Tester (BST), is inserted Into a 3-inch-diameter borehole to the desired depth, locked Into position, and activated to shear the rock or coal in the borehole walls. The normal and shear pressures exerted by the BST, which are recorded during the test, are used to calculate the shearing strength and the angle of internal friction. The BST consists of 3 main components and several minor components. Main components are: ? A shear head with 2 shear plates that bite into the rock when normal pressure is applied. ? A hollow hydraulic jack with RW drill rods that pull the shear head when shear pressure is applied. ? A console with a hand pump and two hydraulic gages to activate the device and to indicate the pressures that apply the normal and shear faces to the shearing plates.

Jan 1, 1981

By Travis Q. Lyday

Ecuador&apos;s economy continued to slow in 1982 due, in part, to declining foreign demand for oil, depressed world oil prices, and high international interest rates. Real growth of the gross domestic product (GDP) was estimated to be in the 2% to 3% range, down from the revised 4.3% recorded in 1981 and the 4.5% anticipated officially. In current prices, the GDP in 1982 was estimated at $12.1 billion.2 Inflation abated slightly from that of 1981 to an estimated 13.9% annual rate. The sucre was devalued in May by 32%, the first time in more than a decade, as a result of the pervasive flow of capital abroad. Ecuador&apos;s production of petroleum increased an estimated 1.9% in 1982 compared with that of 1981. The consortium of Corporación Estatal Petrolera Ecuatoriana (CEPE), the state oil company holding a 62.5% interest, and Texaco Inc. (37.5%) produced an estimated 98%, or approximately 211,000 barrels per day, of the total from the northern part of El Oriente, the eastern jungle region, where a Texaco-Gulf Oil Corp. partnership discovered oil in 1967. Gulf subsequently sold out to CEPE in 1977 for $117 million, Remaining production was from the Santa Elena Peninsula Fields on the Pacific coast where production has been steadily declining for several years.

Jan 1, 1984

By W. A. Cole

As the mines get older and the active workings get Farther and farther away from the original mine openings, it becomes increasingly difficult and expensive to ventilate most coal-mines properly. At the same time, the avenues of escape for those employed underground have become so extended&apos; as often to make it impossible for them to make their way out of the mine in the event of a fire, mine explosion, or other emergency. Where such Conditions exist, the only satisfactory solution is to make new ventilation and emergency-escape openings near the active mine workings. At most mines this would necessitate sinking shafts, which is often slow and expensive.

Jan 1, 1945