Search Documents

By Edward D. Thimons

The Bureau of Mines conducted in-mine tests to determine correction factors applicable to low-velocity airflows (below 150 fpm) measured by the smoke cloud, vane anemometer, and oil of wintergreen tracer gas techniques 0 The average correction factors found for these methods of measurement were lower than those reported in the literature for use with higher velocity measurements. All tests measured airflows with controlled average velocities ranging from 50 to 100 fpm. Correction factors averaged about 0.75 for readings taken by the centerline smoke cloud method, remotely controlled and stickheld center" line anemometer, and split traverse stick-held anemometer. For hand-held centerline anemometer and oil of wintergreen tracer gas readings, correction factors averaged about 0.67. Since special anemometers are needed to measure airflows in this low-velocity range, and since proper calibration of these anemometers is difficult and expensive, the use of anemometers for low-velocity measurement is imprac-tical. On the other hand, smoke and oil of wintergreen give results as con-sistent as those obtained with specially calibrated, low-velocity anemometers. Furthermore, they are easy to use and inexpensive.

Jan 1, 1979

By Michael D. Fenton

Bauxite resources were primarily in Africa, Asia, Oceania, and South America. Only five countries combined, Australia, Brazil, Guinea, India, and Jamaica, contained most of the total world reserves available for extraction under current economic conditions and accounted for nearly 80 % of world production of bauxite. World bauxite and alumina production declined and prices for smelter-grade alumina remained below the $200/mt level during 1993 because of growing aluminum inventories on international markets and declining worldwide demand. The United States imported bauxite primarily from Australia, Brazil, Guinea, and Jamaica. U.S. alumina plant capacity remained essentially unchanged throughout 1993, but apparent capacity utilization decreased by the close of 1993. Chromium Most of the world's known resources and reserves of chromite are located in India, Kazakhstan, South Africa, and Zimbabwe. India, Kazakhstan, and South Africa accounted for 73 % of world production of chromite. The two largest producers of chromite, Kazakhstan and South Africa, were in the process of major economic and political change during 1993. South Africa's production and exports of chromite continued to fall during 1993, because of weak international demand and a flood of cheap metal from the former U.S.S.R. and China into world markets. Despite a significant increase in production, South Africa's ferrochrome producers continued to operate below capacity in 1993. Prior o the dissolution of the U.S.S.R., Kazakhstan was a major internal supplier of chromite ore to the U.S.S.R. consumer, but subsequent decline in demand led to a downward trend of chromite production in Kazakhstan and increasing exports to Europe during 1992 and 1993. The United States consumed, about 10% of world chromite ore production in various forms of imported materials. The United States imported nearly one-half of its required chromium contained in chromite ore and chromium ferroalloys and metal from South Africa; the remainder was from the minor producers Turkey, Yugoslavia, Zimbabwe, and others.

Jan 1, 1995

By William C. McBee

Prompted by forecasts of a sulfur oversupply, the Bureau of Mines, U.S. Department of the Interior, is conducting research on potentially large-scale uses of this commodity to extend or replace such construction materials as asphalt, cement, and mineral aggregates. Through these efforts, paving materials have been developed in which sulfur replaces up to 50 pct of the asphalt normally present and which can be prepared and placed with existing mixing and paving equipment. Laboratory properties and design methods for this direct mixing process are described along with properties obtained on small-and large-scale field demonstration projects. These properties are compared with those obtained from control materials prepared without sulfur additions. Monitoring for toxic gases during laboratory and commercial mixing and paving operations is discussed also.

Jan 1, 1978

By T. R. Taubert, D. H. Carlson, J. H. Johnson

The U.S. Bureau of Mines and Michigan Technological University (MTU) are collaborating to develop an apparatus for measuring diesel tailpipe emissions in underground mines. A tailpipe emissions measurement apparatus (EMA) is described that dilutes diesel exhaust and measures the concentrations of diesel particulate matter (DPM), CO, CO, NO, and NO, at known dilution ratios. The EMA was evaluated by side-by-side comparison of its measurements with those by laboratory- grade instruments. Concentrations of CO and CO, measured by the EMA were usually within + 14 pct of concentrations measured by laboratory-grade instruments for CO and 220 pct for CO,. EMA- measured DPM concentrations were, on average, 29 pct lower than those measured by laboratory-grade instruments, with the differences being fairly consistent. The CO and CO, differences are related to the method of calculating the EMA's dilution ratio, and the difference in DPM concentrations is attributed to thermophoretic and/or condensation losses related to the EMA's unheated sample probe. Preliminary analysis of data obtained with a heated sampling probe and modifications in the sampling procedures have indicated reduced variability in DPM and in the calculated dilution ratios.

Jan 1, 1992

By Donald A. Wilson

As part of a continuing effort to maximize metal recovery from domestic secondary resources, the Bureau of Mines investigated a process for recovering the metallic portion of scrap alkaline batteries. A pyrometallurgical method for recovering nickel and cadmium from Ni-Cd scrap batteries previously developed on a laboratory scale, was scaled up to 25-and 43-pound charges. The method employed reduction and/or decomposition in a retort using a minimum of 2.5 percent carbon as a reductant. Metallic cadmium was distilled at atmospheric pressure and a minimum of 900° C. Purity of the recovered cadmium was 99.8 percent minimum and the nickel-iron residue contained less than 0.02 percent cadmium.

Jan 1, 1981

Accurately measure time of detonation and explosive detonation velocity in a blasthole for analysis of explosive performance and delay intervals. Approach A blasthole-monitoring fiber optic probe was developed consisting of filer optic cable to carry the fight and a sensor to detect and convert the light signals into electrical signals. Events can then be recorded on an oscilloscope, tape recorder, digital computer, or start-and-stop timer. This method is simpler to use and more immune to electronic noise than existing resistance techniques. The fiber optic material,, are inexpensive and easy to obtain, and the recording devices, such as storage oscilloscopes, arc available or easy to obtain. The probe provides the mining industry, explosive manufacturers, and those studying blasting, with a practical alternative to complex and expensive coaxial cable reflectometry, resistor strings, or resistance wire methods for determining explosive and detonator performance. How It Works The fiber optic cable is a plastic light guide consisting of sixteen 0.01-inch-diameter optic strands having an overall outside diameter of 0.087 inch. The receiver module incorporates a photodiode to detect the signal and an integrated circuit receiver for signal amplification into one package about 1/2 by 5/8 by 7/8 inch.

Jan 1, 1989

By D. R. Tesarik, M. K. Larson, J. P. Dunford, E. G. Zahl

Western coal mines are operating under increasingly challenging ground conditions. Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are cooperating with mines to evaluate how these conditions affect mine opening stability and related miner safety. A system was developed to monitor rock and coal stresses during mining of an entire longwall panel. The system was designed to generate data in near real time to evaluate rock behavior in roof strata and the onset of hazardous conditions as overburden stress was redistributed over working entries during gob formation. Computer simulations and in-mine evaluations were used to optimize instrument placement. A prototype packer assembly was designed and tested for installing sensitive instruments in a mine roof. This paper provides background information on the stress monitoring concept and focuses on the development of instrument placement techniques and the prototype packer assembly.

Predict the cumulative hydrologic impact of mining on the environment. Approach A comprehensive set of computer models has been developed to predict the impact of mining on ground water. Mine inflows, drawdowns in aquifers, and ground water quality can be predicted. How It Works The Prickett-Lonnquist finite-difference groundwater model was specially modified for the hydrologic problems of mining. This model, developed at the Illinois Water Survey in the 1960's,

Jan 1, 1982

By R. D. Saltsman

Under contract with the Federal Bureau of Mines, Bituminous Coal Research, Inc., performed a statistical study to find less expensive and time-consuming methods of monitoring the noncombustible content of coal mine dust. Calculations based on thermodynamic considerations verified the reasonableness of Federal rock-dusting requirements. The results of extensive sampling in southwestern Pennsylvania mines indicated that, at the 95-percent confidence level, the present system of sampling at 200-foot intervals may be replaced by sampling at 500-foot intervals, and that a 1-inch scoop floor sampler may replace the standard 6-inch scoop for floor sampling. Further field testing is recommended.

Jan 1, 1975

By John Gross

The modern practice of grinding ores so that often 80 per cent or more of the product is finer than 200 mesh makes it desirable to supplement sieve sizing so as to extend considerably the range of sizing. Moreover, the fact that the material finer than sieve size represents the major part of the work done in grinding emphasizes thick need in can investigation of crushing efficiency. A method based on the settling rate of particles in grater appeared to be most practical for sizing; finely ground ores. There are two possible methods of utilizing this principle: one based on free settling or sedimentation; and the other on separation by means of a rising; current of water, or elutriation. In sedimentation, mechanical entanglement causes material at the start to settle in a mass, and this persists throughout. As this feature is largely eliminated by elutriation, which permits a comparatively clean separation of the various sizes, the elutriation method was adopted.

Jan 1, 1929

By Linda L. Chasko, Charles P. Lazzara, Ronald S. Conti, William J. Wiehagen

Fire has long been a concern for underground mine workers. A mine fire can occur at any time and can result in a partial or total evacuation of mine personnel and the loss of lives. Fires can grow rapidly. Time is the critical element. Prompt detection, timely and accurate warnings to those potentially affected, and a proficient response by underground miners can have a tremendous impact on the social and economic consequence of a small underground fire. Fire preparedness and response have components of technology and people. These components can work synergistically to reduce the time it takes to bring the system back in balance. This report deals with the preparedness of miners to respond to underground mine fires. It is intended to aid the mining industry in understanding the various roles of emergency responders and the training techniques used to increase their skill levels. The report also presents a technology overview to assist in effective response to mine fires.

By M. R. Geer, H. F. Yancey

"INTRODUCTION The increased use of coal as pulverized fuel has focused attention on the grindability of coal and on the necessity of evaluating this property by a method suitable for use in the usual coal-testing laboratory. Without some knowledge of how various coals behave in the grinding operation, that is, how their use affects mill capacity and power requirements, the selection of coals for pulverized-fuel plants cannot be made on the same critical basis used in selecting coals for other types of burning equipment. The grindability of a coal, serves principally as an indication of the mill capacity attainable in grinding it - not as a direct index of the total cost of grinding. Although the grindability of coal may play a minor role at some plants, it is a decidedly important factor where pulverizer capacity limits the ability to carry high loads.Purpose Standardized tests for determining the grindability of coal are relatively new, so that the information now available on the grindability of various coals is limited in comparison, for example, with that available on proximate analyses. Published information is restricted to determinations on many important Eastern coals by the Fuel Engineering Co. of New York, 4/ a bulletin giving the results of numerous tests by the Babcock and Wilcox Co. 5/, and a comprehensive report on. Alabama coals by the Bureau of Mines. 6/This report presents the results of grindability tests of 34 samples of coals from Illinois, Kentucky, Pennsylvania, Utah, Virginia, Washington, West Virginia, and British Columbia at the Northwest Experiment Station of the Bureau of Mines, Seattle, Wash., in cooperation with the College of Mines of the University of Washington. In the future, as the laboratories of the Bureau make grindalility tests of other coals, additional reports will be issued."

Jul 1, 1938

By J. E. Zeilinger

The technical feasibility of using energy from explosive ignitions of coal dust to pump water was .demonstrated in an exploratory investigation. Ignition of small amounts of pulverized coal that were dispersed in air over columns of water pumped up to 5.3 gallons of water per cycle when operated against a head of 30.75 feet. Water displacement was accomplished by either manual or automatic operation through a single cycle, and by automatic operation through a continuous series of cycles of I-minute duration. Operating through single cycles, slurries containing up to 3 pounds of coal and 4.6 gallons of water were also pumped. Possible uses of an efficient coal-fired pump would include pumping water for irrigation purposes, removing water from mines, transporting coal from mines in the form of a slurry, and pumping water to elevated reservoirs at electric powerplants so that it could be used to generate electricity during peak periods of demand.

Jan 1, 1966

By L. Prosser, A. Iannacchione, G. Esterhuizen

The potential for roof falls in underground mines remains a clear and present danger for mine workers. An investigation of ground conditions in nearly 50% of the nation’s underground stone mines found that the state of roof stability is primarily determined in a limited and subjective manner. These large opening mines, with roof heights typically of 7 m or more, make physical observation difficult. Although some mines use monitoring techniques to gain additional information on roof stability, this practice is usually short-term and localized to address ground conditions in a particular section or part of the mine. A methodology to assess the risk for a roof fall is proposed in a preliminary fashion based on engineering judgment acquired from extensive underground stone mine experience and examination of related literature. The proposed method utilizes an observational technique to identify the risk of roof falls in three categories. Case study scenarios provide a realistic picture of model implementation. Providing the mine level decision maker with an accurate assessment tool to ascertain the level of risk related to ground conditions is expected to reduce mine worker injuries and fatalities. Moreover, the presences of danger can be overcome with a clear picture of quantified ground conditions.

This Volume documents the Phase 111 effort on the Seismic Detection and Location of Isolated Miners on Contract H0122026 undertaken during the fall of 1972 by a task team composed of ADL staff and several seismic consultants. The team was assembled specifically to work together on complementary tasks, at an accelerated level of effort for four months, to meet the Bureau of Mines' time schedule for obtaining independent, objective, technical judgments regarding seismic methods and systems for detecting and locating isolated miners. The impetus for this work resulted from a compilation and analysis, during the first half of 1972, of new experimental data obtained from a series of in-mine field tests conducted by Westinghouse Corp .+ using the CMRSS* interim seismic location system. The Bureau of Mines took advantage of the availability of these new data to reassess the potential and limitations of various seismic methods and systems, and to direct its seismic system improvement program accordingly. ADL assisted the Bureau in this reassessment by drawing on the skills of seismic consultants from industry, universities and government, to supplement the skills of the ADL project team. The consultants were principal resources of broadly-based and detailed technical expertise in the areas of seismic signal-source and signal-propagation characteristics, natural and cultural seismic noise, seismic sensors and field instrumentation, seismic signal and data processing for detection and location, and overall seismic system utilization in the field under operational emergency conditions. Specifically, the participating consultants were: F. Crowley, Air Force Cambridge Research Laboratories ; W. Dean, Teledyne Geotech, Alexandria Laboratories; R. Greenfield, Pennsylvania State University; J. Kuo, Columbia University; D. Peters and R. Crosson, University of Washington; and F. Pilotte, U.S. VELA Seismological Center. The principal ADL participants were J. Ginty, R. Lagace, M. Roetter, and R. Spencer.

Jan 1, 1974

By Ann G. Kim

Gas samples containing 02, N2, H2, He, CO2, CO, CH4, and trace amounts of C 2 to C6 hydrocarbons are analyzed by a gas chromatographic method that utilizes both thermal conductivity and flame ionization detectors. A porous polymer support and molecular sieve columns are used with argon as the carrier gas. A column selector valve makes it possible to perform a complete analysis either on one 1-ml sample in 40 minutes or on two samples in 20 minutes, one sample for each detector. Samples are introduced either by on-column injection or through a gas sampling valve. By varying operational parameters, the speed, sensitivity, and accuracy of analysis may be modified to suit a particular situation.

Jan 1, 1974

By M. A. Trevits, S. W. Lambert

In this Bureau of Mines investigation, production was monitored for 1 year at over 30 coalbed gas-drainage boreholes located in Alabama, Pennsylvania, and West Virginia. Results indicate that the quality of data gathered from such wells can be improved greatly if potential problems are anticipated and prevented in the early stages of well production. Major water-monitoring problems include solids buildup, freezing, the presence of gas in surface waterlines, and improper pumping interval settings. Such problems may be avoided by incorporating in the original well design waterline filters, sand screens, separator tanks, and systems to automatically control pumping intervals. Problems related to measurement of coalbed gas flow include large quantities of water vapor contained in the gas, especially during winter months; freezing and subsequent obstruction of flow; sudden, uncontrolled release of gas pressure; and solids buildup in metering equipment. The installation of commercially available items, such as filters, separators, and insulation, and the thoughtful application of a basic knowledge of coalbed gas reservoir characteristics will prevent most production-monitoring problems.

Jan 1, 1978

By Travis Q. Lyday

The Other South Pacific Island states extend from Palau, also called Belau, near the Philippines in the west, to French Polynesia in the east. However, a number of countries and territories have been omitted, from this chapter because their mineral production was insignificant to the local economy. These include the French over-seas territories of French Polynesia and Wallis and Futuna Islands; independent states, including Kiribati, Marshall Islands, Micronesia, Palau, Tonga, Tuvalu, and Vanuatu; the New Zealand freely associated state of the Cook Islands, and the New Zealand dependency of Niue. What mineral production existed in these islands was limited to construction materials such as coral reef limestone, crushed stone, and sand and gravel in minor quantities solely for domestic consumption. FIJI The mineral industry of Fiji continued to be dominated by gold, although this sector contributed less than 1 % to the gross domestic product (GDP) of the country. Gold and silver together ranked second in value among the country's exports. Fiji's economy contracted 11% during the 8-month period following the first, on May 14, of two military coups. Although the island nation had been a member of the British Commonwealth of Nations since its independence on October 10, 1970, Fiji's membership terminated with the emergence of the Republic or Fiji on October 15.

Jan 1, 1989

By D. Harrington

"The recent discovery and exploitation of petroleum territory have resulted in the enactment of new petroleum laws in most of the South American Republics. The activities in the discovery of these new fields were engendered by the knowledge of the fact that present producing fields must within well defined periods be exhausted. Oil operators were willing to take the initial steps in exploitation in the absence of legislation that applied strictly to petroleum operations. The enactment of modern legislation in many of these Republics encouraging and protecting exploitations may cause tremendous oil activities in these countries, and the results may be comparable with the magnitude of the undertakings and the prestige of the companies now entering this territory.These, oil fields are admirably located for convenient distribution of petroleum by water to all the Nations using oil as fuel for shipping and industrial concerns. The oil markets of the western coast of South America will derive immense benefits from the Panama Canal. This navigation route brings these markets into direct ocean shipment with the Atlantic coasts of the Western and Eastern Hemispheres.One deterrent to oil production in the Republics of South America is the want of inland. transportation facilities, but the recent laws of these Republics without exception provide for acquiring rights of way for pipe lines and other modes of transportation; and doubtless the great interests and. syndicates already operating in these regions will, as production increases, provide ample pipe line transportation sufficient to convey to the coast the oil produced. It way be assumed, from the legal guarantees afforded, and from operating equipment and machinery that are now being concentrated that refineries will be erected at shipping points for the purpose of making these petroleum products accessible to the world."

Jun 1, 1921

By C. B. Manula, R. L. Sanford, R. A. Rivell

The large amount of computer code required for this simulation model dictates that reasonable limitations be placed on some of the input variables. The program permits the following maximum sizes: 1. Ten mine car stations 2. Twenty track intersections 3. Three hundred mine cars 4. Eight motors 5. One hundred profiles 6. Twelve intersections between stations 7. Forty-five profile changes between stations 8. Thirty station pairs (routes) These may be changed by the user providing the particular computer in use has available core storage. Major Array Descriptions This section is a detailed description of four of the major arrays used in the rail haulage simulator for data storage and logical control. Other arrays are used; however, they may be considered sub¬servative to the major ones. These major variables are explained on the following pages. Motor Control Array (XXXDEF). The first 99 locations in this array are arranged according to and are developed by data input. Unit conversions are made at input time which include: 1. Tons to pounds. 2. Rolling resistance in pounds/ton to percent/100. 3. Miles per hour per second (mphps) to feet per min. per minute. 4. Miles per hour to feet per minute. The following information is stored for each motor at the array

Jan 1, 1974