Search Documents

By Jr. Dubaniewicz, Gregory M. Green, Kenneth L. Cashdollar

Laser-based instruments are used in areas where coal dust ignition presents a safety hazard. The National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory ~NIOSH, PRL! is conducting a study to help determine when an optical beam may be considered a potential ignition source in underground coal mines or coal storage facilities. Researchers conducted experiments to determine threshold igniting powers for Pittsburgh seam bituminous coal dust clouds using an 803 nm continuous wave laser. For fine sized coal dust dispersed in air, concentrations ranging from 600 to 2000 g/m3 were the most easily ignited. A heated layer of coal dust that deposited on the fiber tip during dispersion ignited the dust clouds. Minimum observed igniting powers for laser beams delivered by 200, 400, and 800 mm core fiber optic cables and directed into coal dust clouds were 2.0, 3.0, and 5.0 W, respectively. Threshold igniting power was proportional to beam diameter, and threshold igniting power density decreased with larger fiber diameters. Ignition delay times averaged 0.6 s and did not vary significantly with laser power under initially turbulent test conditions and with flammable targets. Comparisons are made with the results of other researchers.

By G. M. Martinez

A cell concept adaptable to large-scale electrowinning of zirconium metal from zirconium tetrachloride was investigated by the Federal Bureau of Mines. Tests were made in twin cells, each 12 inches in diameter by 33 inches long. Electrowinning was performed in one chamber from which the electrolyte was transferred after electrolysis to the other chamber where it was renewed by the introduction of ZrC14 by direct sublimation. The formation of a salt plug in the connecting pipe provided a seal between the chambers. Optimum electrolyte composition, with respect to quality of the metal product (91 pct meeting ASTM standards except for the oxygen content) and current-carrying capability (about 350 amp) was determined to be 16.7 wt-pct NaF-83.3 wt-pct NaCl mixture plus ZrC14 equal to about 3 wt-pct zirconium. A twin-cell design incorporating the unit operations covered by this investigation is proposed.

Jan 1, 1976

By Will H. Coghill

Recent work on beneficiation of the .Alabama red iron ores and ferruginous sandstones has brought out interesting new facts on particle-size reduction that axe a valuable supplement to what is already known.4/ The work was done by the Southern Experiment Station of the Bureau of Mines in cooperation with-the University of Alabama, University, Ala., on two samples from the Birmingham district. One was an oolitic red iron ore containing about 35 percent iron; the other was a ferruginous sandstone containing about 25 percent iron, particularly attractive because of its low phosphorus content. In both samples rounded quartz (sand) grains were embedded in an oolitic, "onion skin" matrix of hematite. The hematite carries varying amounts of clay, which limits the grade of concentrate that can be made. The clayey hematite is soft, so that the rock crumbles readily under pressure. The sand grains shell out like corn,, and without much exaggeration the mill used for differential grinding might be called a "sheller,"

Jan 1, 1940

Predict the spontaneous combustion potential of a coal, using an expert system computer program. Background Approximately 15% of underground coal mint fires in the United States are attributed to spontaneous combustion. These spontaneous combustion fires frequently occur in worked-out or abandoned areas of a coal mine, This makes the control and extinguishment of the fire difficult and often requires large sections of the mine or even the entire mine to be scaled for long periods of time. A prior knowledge of the self-heating potential of the coal can be useful in preventing spontaneous combustion fires through the use of aggressive monitoring and control measures at existing coal mining operations, and in the planning oh new mines. Many factors can affect the spontaneous combustion process in a mine, including the self-heating potential of the coal, ventilation, geologic factors, and mining conditions and practices. Various test methods have been used to evaluate the relative self-healing potential of coals, including crossing point temperature and adiabatic heating methods, and oxygen adsorption techniques. However, these tests arc usually time-consuming and difficult to conduct, limiting their use to laboratories.

Jan 1, 1992

By E. S. Longfellow, S. H. Katz

Poisonous hydrocyanic acid gas (HCN) is sometimes evolved in dangerous quantities from cyanides used in metallurgical and chemical operations. This gas is much used for fumigating buildings, ships, greenhouses, and such commodities as grain and cotton to destroy rats, mice and insect pests. Wherever cyanide fumes are evolved, thorough ventilation is necessary in order to render the sur- rounding air safe to breathe. Many persons have been killed by entering tanks and fumigated places too soon, and a simple test for this gas would promote safety. In view of the need for an easy method for quantitatively determining HCN in air, the three color reactions used originally for testing HCN in solution tions *** were modified and adapted. The reactions employ (1) picric acid (CH(NO2)3OH) which is yellow but combines with hydrogen cyanide to form a red- purple dye, isopurpuric acid****; (2) phenolphthalin (CH1604), which is a reduc- tian product of the phenolphthalein (CH4) used for acid indicator, this colorless substance is oxidized***** by presence of HCN to pink colored phenolph- thalin; and (3) guaiacum which oxidized from colorless to blue******. Phenolph- thalin and guaiacum require the presence of copper compounds which catalize the color formation by reduction of cupric cyanide. The chemical processes involved *Associate physical organic chemist, Bureau of Mines, Department of the Interior. **Assistant gas chemist, Bureau of Mines, Department of the Interior. 2014 20 *** Kohn-Abrest, E., Notice toxicologique sur les gas: Arnales des Falsifica- tions, vol. 8, 1915, pp. 215-35. (Tested air with picric acid and guaiacum papers). **** Élasiwietz, H., Ueber eine neue Zersetzungsweise der Trinitrophenylsaure: Anal. der Chemie, vol. 110, 1859, pp. 289-303. ***** Weehuizen, F., Phenolphthalin as reagent for HCN: Pharmaceutrisch weekblad, Utrecht, vol. 42, 1905, pp. 271-2. Abstract, Jour. Chem. Soc., vol. 88, part 2, 1905, p. 489. ****** Schonbein, C. F., Ueber den thatigen Zustand der Helfte des in dem Kupfer- oxydenthaltenen Sauerstoffs und ein darauf beruhendes hochst empfindliches Reagens auf die Blausaure und die loslichen Cyanmetalle: Jour. fur. Praktische Chemie, vol. 106, 1869, pp. 263-70.

Jun 1, 1923

By Hillary W. St. Clair

The effective coefficient for rate of reduction of a sample of granular iron ore may be determined by passing the reducing gas through a bed of the are at constant flow rate and periodically analyzing the effluent gas, The method of analyzing the data is based on a mathematical model that takes into account the variation in composition of the gas and solids with time and position in the bed. A method is described for determining the value of the rate coefficient that gives best agreement between the observed and calculated analyses of the effluent gas.

Jan 1, 1967

By R. V. Lundquist

Lime-soda sinters, made and processed for recovering alumina and soda, consisted of several types of compound structures differing from the ideal dicalcium silicate and sodium aluminate. Many or these compound structures were causes for low alumina recovery and contributed to the relation or leach slurries. Presence or free lime, whether in the sinter or released by hydrolysis of sinter compounds, contributed to relation of leach slurries. Free lime tends to establish the initial viscosity assumed by a leach slurry. Previous investigations by the Bureau of Mines (1, 4)4/ and by other laboratories (5) have demonstrated the technical applicability of the lime-soda sinter process to the recovery of alumina from aluminum silicate materials. The basic concept of the process is sintering aluminum silicate materials with limestone and soda ash for the production of dicalcium silicate and sodium aluminate and then extracting the sodium aluminate by leaching the sinter in causticized liquors. Alumina is precipitated from the pregnant liquors by carbonating with carbon dioxide. Reaction in the sintering operation may be represented by the following simplified equation: A1203?SiO + 2CaCO3 + Na2C03 = 2Ca0?SiO + Na20?Al203 + 3C02

Jan 1, 1960

By C. I. Pierce

The Bureau of Mines conducted laboratory tests to determine if ultrasonic energy could reduce either the residual water or oil content of petroleum reservoir-rock samples from Appalachian area oilfields. Brine-saturated core samples were flooded with oil to residual brine saturation and subjected to 20 kilocycles per second ultrasonic energy. Then they were flooded with brine to residual oil saturation and again subjected to ultrasonic energy. Additional water displaced as a result of the application of ultrasonic energy to the flow system ranged from 0 to 4.3 percent of the original brine and averaged 1.9 percent. The increase in oil recovery as a result of the ultrasonic energy ranged from 0 to 9.0 percent of the original oil and averaged 3.1 percent. On the basis of the tests, it appears that 20-kcps acoustic waves would not have field application for oil recovery.

Jan 1, 1968

By Thomas E. Marshall, Timothy Batchler, Anthony T. Iannacchione

As the amount of new fractured surfaces or "damaged rock layers" within roof rock increases, the stability of the rock mass decreases. While direct measurements of this phenomenon are not easily made, there is good circumstantial evidence to support this hypothesis. For example, it is common to observe increased cracks or fractures in the immediate mine roof rock before a roof fall. Likewise, roof drill holes placed in areas that later fail often reveal increased numbers and/or separations of fractures within the rock column through time. And finally, the frequency of microseismic activity, representative of rock fracturing, increases before a roof fall. For this study, more than 700 microseismic emissions were collected from two underground limestone mine roof fall areas in southwestern Pennsylvania. Microseismic events were located and magnitudes determined using the moment magnitude technique. Moment magnitude is based on the event seismic moment, which is a measure of the seismic deformation. The amount of new fracture surface length was calculated based on the stored strain energy within the rock prior to fracture. In the two case studies presented, a significant amount of microseismic activity was observed as much as two days before the first signs of failure in the roof fall areas. Additionally, results from this analysis reveal much about the behavior of strata prone to failure and allows for the construction of hazard maps based on microseismic emissions. The potential use of this technique as a means of anticipating roof falls is analyzed and discussed.

By Robert R. Stein, Roy C. Bartholomae, William W. Aljoe

This Bureau of Mines report describes in detail the design and operation of a test apparatus for measuring the sound power levels of drills used by the mining industry. The two major components of the test apparatus are a computer-controlled automated drill test fixture (ADTF) and a large (45,000-ft3) reverberation chamber that houses the ADTF. Design specifications and performance capabilities of the ADTF and the reverberation room are given. Initial test results for three types of drills--a pneumatic percussion drill, a hydraulic percussion drill, and a pneumatic rotary drill--are given to illustrate the types of experiments that can be conducted with the test appartus.

By Alan G. Mayton

A prototype end-cab shuttle car (SC) design has been developed to improve protection and address ergonomic concerns of the SC operator in low coal mines. The new design features an end cab transversely mounted to the SC and equipped with a closed-circuit video system. The end cab was retrofitted to a low-coal SC and evaluated in surface trials at the U.S. Bureau of Mines. During surface trials, test operators evaluated the end-cab SC relative to visibility; cab features-space, seating, controls, and operator position; tramming-inby, outby, and turning corners; and dumping. Trials were conducted using 12 test subjects; 6 were experienced SC operators. Results of the trials were promising. Of the experienced operators, the only operator with low-coal experience gave the new design the highest rating. Four experienced operators rated the end-cab design "better" to "much better" than a standard center-driven, side-cab SC for visibility when tramming, protection from roof and rib hazards, and no change in seat position with direction of travel. This report discusses research to modify a used 21SC JOY SC, retrofit the SC with the Bureau-developed end-cab, and evaluate the retrofitted end-cab SC in surface trials.

Jan 1, 1993

By C. H. Elder, Fred N. Kissell, S. D. Maksimovic

The Bureau of Mines evaluated the hydraulic stimulation of a gob-degasification borehole to determine if this procedure would aid in degasifying a longwall panel. The stimulated borehole did not degasify the longwall panel as expected either before or after mining of the panel started. It reduced the underground methane emission only 11 pct, considerably less than the reductions effected by two unstimulated boreholes in the same panel. Some probable reasons for the reduced methane flow from the hydraulically stimulated borehole are very low reservoir gas pressure, location of hydraulically stimulated zones within the grouted casing, a casing break caused by lateral shifting, possible vertical movement of rock strata during caving, grouting of a 4-inch pipe blocking three stimulated zones, plasticity of shales, and possible hole damage by swelling of water-sensitive minerals. The borehole was also located between two second-mined areas, which may have allowed partial degasification of the overburden and the coalbed in advance of mining. Finally, a period of 3 months is probably not long enough for the borehole to degasify the overburden before mining.

Jan 1, 1977

By E. R. Cole

Bench-scale research at the Bureau of Mines has resulted in the successful development of a combination electrorefining-electrowinning method for recycling all the lead in scrap batteries. The method reduces energy consumption and eliminates toxic emissions, in contrast to present pyrometallurgical smelting, and the lead produced is pure enough for use in maintenance-free batteries. Anodes cast from molten lead scrap were electrorefined in 1-and 2-liter plastic cells using an electrolyte composition of 70 g/l Pb and 90 g/l free H2SiF6 (fluosilicic acid). Both reagent-grade and waste H2SiF6 were used. Cathode starting sheets were made from refined lead. Aloes, and later bone gelatin, and calcium lignin sulfonate addition agents were employed. The sludge remaining after separation of the lead metal was treated in a two-step leaching operation to solubilize the lead for recovery by electrowinning. Conditions for electrowinning were essentially the same as for electro-refining, except that insoluble Pb02-Ti (lead dioxide-coated titanium) anodes were used. The best results for both electrorefining and electrowinning were obtained with a current density of 170 amp/m2 and a cell temperature of 25° to 35° C. Cathode purity ranged from about 99.9 to 99.99+ pct Pb. Maximum energy consumption after 3 days, for electrorefining and electrowinning, was 90 and 700 kwhr per metric ton of refined lead, respectively.

Jan 1, 1981

By H. G. Iverson

An investigation was conducted on the conditions affecting the precipitation of aluminum by autoclaving synthetic solutions containing Na2SO4, Al2(SO4)3, H2SO4, and H2O. Virtually all of the alumina could be precipitated as natroalunite (NaAl3(SO4)2 (OH)6). This product could be readily filtered and dried. Results are reported in terms of alumina precipitated in this compound and not in terms of alumina itself. Solutions of ~ 0.30, ~ 0.60, and ~ 0.80 mole/liter A1203 and various concentrations of H2SO4 and Na2S04 were investigated. The optimum time and temperature for autoclaving were 20 to 30 minutes at 200° C. The highest yields of natroalunite were obtained from solutions containing little H2SO4 and ~ 2 moles Na2SO4 per mole A1202. Acid in quantities of 0.3 to 0.5 mole/mole of alumina in solution depressed the yield to 90 percent or less. In differential thermal analysis, at 1,000° C the natroalunite precipitate decomposed without melting to yield SO, and SO2 gases, a solid composed of Na2SO4, and gamma and alpha Al203. Continued heating to 1,200° C produced No SO, and alpha A1303. Water-leaching of this product removed the Na2S04 and left a final residue of alpha A1203.

Jan 1, 1968

By Andrew B. Cecala

This U.S. Bureau of Mines report provides a detailed description of the Bureau-designed modified shearer clearer system. Engineering drawings are provided for all major components of this system. The modified shearer clearer system is a revised version of the original system and is intended to improve the ventilation around both cutting drums. The original shearer clearer technique was solely a dust control technique that has been effective in lowering shearer operators' dust exposures. The technique uses a series of water sprays that not only knock down a portion of the dust cloud but also act as small fans that move a substantial amount of air and keep the dust cloud from dispersing over the shearer body. The modified version is composed of two additional spray blocks for improved air movement around both cutting drums, thus lowering methane levels and the likelihood of an ignition. A laboratory study performed with the modified version in a full-scale longwall gallery resulted in a 73-pet reduction in methane concentrations at the shearer machine for both cut directions. The air-moving capabilities of the system provide more turbulence at the cutting drums and reduce methane levels.

Jan 1, 1994

By Robert M. Doerr

In a process being investigated by the Bureau of Mines for recovering alumina from domestic nonbauxitic resources, calcined kaolinitic clay is leached with hydrochloric acid. Iron impurity in the clay is coleached and is removed in a solvent extraction step prior to crystallization of aluminum chloride hexahydrate, which is subsequently thermally decomposed to alumina. The FeCI3-HCl stripping liquor from the solvent extraction step is unsuitable for discharging to the environment; furthermore, economics requires recovery of the contained chloride values. In the present research, it was shown that the stripping liquor can be reacted with calcined clay to yield AlC13 in solution, plus precipitated iron oxides, residual silica, and unreacted excess clay as mixed solids. For the recovery of the AICl3 solution, the slurry could be separated or returned to the clay-HCI process stream at the solids washing step that follows primary HCI leaching of the clay. For the range 20° to 99° C, the time (t) (103 sec) required to react the waste liquor with excess clay, for essentially complete iron precipitation, depends on the absolute temperature (T) chosen, according to the expression t = e[(9.000/T) -23.5J. (1) Alumina was tried as a reagent alternative to clay but was not very effective, even under pressure and at high temperatures.

Jan 1, 1982

By T. A. Klinefelter

"INTRODUCTION During the development work on sponge iron by the Bureau of lines it was desired to produce a product of maximum density for the furnace. One means of doing this would be to make a plastic mixture of the ground ore and extrude as pellets or large slugs or brick shapes.If a pelletizing Process is employed, the pellets must be strong enough to resist breaking when rolled and tumbled in going through the rotary kiln. If a brick-making process is employed, the brick must be strong enough to withstand handling and considerable pressure when stacked in the kilns.The study had two objectives: first, to find a binder of sufficient strength throughout the early stages of curing and heat treating and, second, to determine the degree of curing and heat treatment necessary to prevent disintegration under normal working conditions.Although the investigation had as its primary objective the processing of sponge iron, the data should interest other industries in which non plastic or poor-bonding slimes are a problem."

Jan 1, 1946

By Bertrand L. Johnson

Fertilizers are indispensable to national preparedness and defense. Production of adequate supplies of nourishing food for sustaining life in the United States is absolutely dependent in many parts of the country on the use of artificial fertilizers of various types. Only by using fertilizers can we maintain our present volume of production without great additional expense. Otherwise we would have to increase crop areas constantly to compensate for declining yields, we would have to lower the quality of food marketed, and standards of farm living and rural civilization would decline. About 60 million of the 360 million acres of crops grown annually in the United States Vow require fertilizing each year, and between 7 and 9 million tons of commercial fertilizers are consumed annually for this purpose.

Jan 1, 1941

Provide a means to (1) rapidly disconnect a multifunctioning signal channel from a multichannel data collection system, (2) protect electronic devices from damage while causing the minimum amount of data collection disruption, and (3) operate electronic devices under gassy mine conditions. Background Data collection system instrumentation and cables are often located in hazardous areas of underground coal mines. As a result, frequent damage to the instrumentation cables occurs from roof falls, heavy equipment, and the relocation of air, water, and power lines. A similar problem exists in surface areas where cables and instrumentation can be damaged by animals and by vehicle traffic. Without a circuit-breaking feature, the damaged cables could cause instrumentation to be ruined, cause power supply failure, and otherwise disrupt data collection in some situations the lack of a circuit-breaking feature might cause an ignition in a methane atmosphere.

Jan 1, 1990

By Peter Kovalchik, Ed Kwait, T. Michael Durr

1. BACKGROUND Many research projects on engineering controls for noise reduction in mining were conducted by the former U.S. Bureau of Mines, mostly under contracts from 1972 through 1986.1 Contracts were awarded to determine which mining equipment was responsible for worker noise exposure over the permitted Federal Regulation level of 90 dBA for 8 hours. Dominate noise sources, for each piece of equipment was also determined. The final goal was to develop engineering noise controls for those pieces of equipment and then evaluate them. This was the general approach taken in each research project or contract. This paper deals with what is known about the control of noise from continuous miners, one of the most commonly used underground mining machines. A literature review on continuous miners revealed that the relevant noise sources were divided into four categories: conveyor, cutting head, drive train, and motor noise. The dominate noise sources reported were the conveyor noise and the cutting noise.2 Conveyor noise consists of impacts and scraping at various locations on the conveyor structure. These impacts are associated with discontinuities on the top and bottom decks, impacts between the chain and the tail roller, impacts on the sidewalls at path points of discontinuity under horizontal pivot, and impacts on the flex plate.3 Scraping occurs along the entire length of the chain conveyor. The other dominate source, the cutting of coal, has also been addressed in past research.4, 5, 6 The research presented in this paper only addresses the controls associated with the conveyor. The literature suggests several effective treatments for noise control: retrofitting the chain conveyor with a urethane coating or a urethane sleeve on the chain flights, using a urethane coating or urethane sleeve on the tail roller, constrained layer damping of the decks, and the use of a modified take up plate.7, 8 However, the in-mine durability of these concepts has yet to be proven for the conveyor system. This paper analyzes extensive noise and urethane durability testing on a Joy 14CM9 continuous miner’s conveyor assembly, tail roller, and bottom plate conducted at the Pittsburgh Research Lab facilities. It will also discuss the initial underground testing results for the urethane-coated conveyor flights and tail roller.