Search Documents

By Gordon H. Dechman

This Bureau of Mines report presents an iterative approximation method for microseismic source location that was developed to adapt microseismic techniques for rock structure analysis to investigations of surface problems, such as slope failure in an open pit mine. The source location method and two derivative location algorithms are described in detail, and the speed and accuracy of the two algorithms are compared.

Jan 1, 1977

Provide a machine for economically drilling probe holes in coal mines (required where there's a possibility of unmapped, abandoned workings) to check for possible water flood or gas hazards ahead of the face. Approach A lightweight air-powered drill, that mounts on a light-weight frame anchored to the face with an expandable packer, is used to drill one or more probe holes. The anchor installs quickly and will lock the drill in any desired position. How It Works The drill is portable and can be broken down to small components for ease of transportation. One man can carry these sections through restricted access routes to the working place. Components that are separable are the anchor assembly, drill frame assembly, and drill motor assembly. The drilling sequence is as follows: A 2-inch-diameter anchor hole is drilled 2 feet deep. The fixed anchor tube is rubber packer is expanded. A second anchor hole is drilled through a bushing in the anchor frame. The removable anchor tube is inserted and its rubber packer expanded. (This anchoring system withstood pulls of up to 14,000 pounds.) Next, the frame is attached to the anchor with two screw knobs, and the motor is attached to inserted in the hole and the rubber packer is expanded. A second anchor hole is drilled through a bushing in the anchor frame. The removable anchor tube is inserted and its rubber packer expanded. (This anchoring system withstood pulls of up to 14,000 pounds.) Next, the frame is attached to the anchor with two screw knobs, and the motor is attached to the frame with a single locking pin. Installing the anchor and drill takes less than 12 minutes.

Jan 1, 1981

By George E. Fasching

The Bureau of Mines has developed a pulse counting system with improved energy resolution and having dual channels to process pulses at different rates and a pulse pileup detector for channel selection. Pulse input is delayed until the detector determines if any pulse is so closely followed by a second pulse as to constitute pulse pileup. If no pulse pileup is detected, the slower channel is selected; this clips the pulse to a wide pulse width to retain good energy resolution. If pulse pileup is predicted, the fast channel, with correspondingly shorter pulse width, is selected to improve resolution with respect to time. Output of the two channels is transmitted to a pulse height analyzer for interpretation. The pulse processing system can process count rates above 300,000 counts per second with little loss in energy resolution.

Jan 1, 1974

By J. M. Singer

Approximate equations were used to compute the radiant heating of float coal dust by approaching flames for various combinations of particle size, dust path length (flame travel distance), flame temperature, dust concentration, flame speed, and flame length. The computed values of degree of radiant heating and flame travel distance for preheating the coal dust should be useful for estimating the increased fire hazard of different coal dust-flame parameters. Some findings relating to coal mine disaster control are-- 1. Coal dust clouds cannot be preheated to ignition temperatures by flame radiation alone when deflagration speeds are greater than about 10 m/sec. Thus it appears unlikely that radiation alone will cause flames propagating in dust clouds to accelerate to detonation velocities. 2. Small particles in the radiation flame zone caused by burnout and soot formation increase the degree of preheat significantly. 3. The concentration of float coal dust (radii = 3 to 40 microns) for maximum radiant heating usually peaks in the range 50 to 200 mg/liter of air.

Jan 1, 1970

Develop a full-length-anchored roof bolt that is economical, nontoxic, nonflammable, and non-allergenic. Approach Grout roof bolts with a storable mixture of ultra-fast setting inorganic cement and water. How It Works A loose mixture of dry cement powder, and pinhead-size water droplets encased in waxy globules, are pack-aged in sausage shaped cartridges for storage and use. After the cartridge is inserted Into a drilled hole, the roof bolt is thrust In and rotated to mix the cement and water. The cement hardens in seconds, providing usuable anchoring strengths in minutes. Prior to filling of the sausage shaped cartridges, the microcapsules of water are Intimately mixed with the dry cement. The currently used grouting consists of a mixture of one part water (minimum) with three parts alpha-type gypsum cement and a minor amount of accelerator.

Jan 1, 1978

By John C. Edwards, Gerald S. Morrow

The U.S. Bureau of Mines has constructed a smoke chamber and developed sensitivity tests for smoke detectors. Response of ionization- and optical-type commercially available smoke detectors have been investigated. Six smoke detectors were measured with respect to visually obscuring smoke characterized by a corresponding optical density for smoldering and flaming coal combustion in the smoke chamber. It was determined that for one type of ionization smoke detector the alarm time was nearly equivalent to that of an odor monitor's alarm for smoldering coal combustion experiments and earlier for flaming coal combustion experiments. The experiments showed that an average CO concentration of 5 ppm corresponded to an optical density of 0.022 m for smoldering and flaming-1coal combustion. Two of the commercially available ionization-type smoke detectors were more responsive to flaming than smoldering coal combustion at an optical density of 0.022 m, whereas the optical smoke detectors-1showed the opposite trend. The responsive characteristics of the detectors evaluated with respect to known smoke conditions in the smoke chamber shows their potential for use as mine fire sensors or part of a mine atmospheric monitoring system to improve mine safety.

Jan 1, 1995

Generate less respirable dust during mining by reducing the clogging and downtime of the water sprays on mining machines, especially on continuous miners. Approach An improved filtering system, having commercially available components, has been designed and tested. How It Works The improved filtering system shown opposite is mounted on the mining machine, where It traps particles of coal and pipe scale which cause most clogging of the water sprays. Water entering the system first flows through a ?Y" strainer, which screens out particles larger than 1/8 inch diameter. Next, the water whirls through a small hydrocyclone. Most of the remaining smaller particles are removed and pass Into the accumulator compartment built into the hydrocyclone. The water also flows through a final filter. This filter catches particles that might pass the hydrocyclone, especially during water spray start-up and shut-down, when the speed of the water flow is not sufficient for

Jan 1, 1976

By J. B. Littlefield

The term "konimeter" is used generally to designate a type of dust-sampling instrument that collects the dust from a small volume of air by impingement on a glass plate prepared aced with an adhesive film. The konimeter was first developed by Sir R. N. Kotze about 20 years ago and was followed a few years later by the circular-type konimeter, by which a number of samples may be collected on a glass disk. The present discussion will be confined to the circular type, as it is used most. Various techniques have been developed for using the konimeter, and many materials, such as petrolatum, mineral oil, and glycerine jelly, have been used in preparing the adhesive film. In South Africa, Australia, and Canada, where the konimeter has been employed most widely, dust samples are treated by ignition and washing before being counted. In Canada the dust samples are collected on a disk of special heat-resistant glass prepared with a film of mineral oil; the disk is then heated to a dull cherry-red in a muffle-furnace to remove the film and organic matter, cooled, and washed with a few drops of 50-percent hydrochloric acid followed by distilled water and alcohol, and then heated again to remove residue left by evaporation of the alcohol. After this treatment, the dust samples are counted under a magnification of 150 diameters with dark field illumination.

Jan 1, 1938

By Launa G. Mallett, Charles Vaught

This report is intended to help mine safety trainers better prepare to teach the influx of new underground coal miners who are entering the industry. This is done by identifying two different approaches to instruction and discussing the ways they may affect how well prepared new hires are to deal with a dynamic and hazardous workplace. One approach is based on the use of a syllabus. Those using a syllabus are more likely to rely on lecturing or direct instruction. This is a good way to get across factual information, but does not provide a context within which miners can fit the discrete facts so that they form an integrated whole set of concepts, principles, and skills. The other approach is based on the use of a curriculum. Those using a curriculum may be more likely to help miners integrate concepts and skills that give them an overall picture of the complex mining environment and how they fit into the workplace. This will better prepare them for the decision-making and problem-solving activities that will help them work safely and productively

Jan 1, 2008

By D. R. Tesarik, F. M. Jones, J. B. Seymour

As part of safety and stability studies at three underground mines in the United States, researchers installed earth pressure cells and embedment strain gauges in cemented rockfill to measure stress and strain changes as mining progressed and the rockfill was loaded. Data from these instruments were used to calculate the in situ modulus of the rockfill for two of the mines. A three-dimensional numerical model of a cemented rockfill cap was validated with data from extensometers anchored in the mine roof and sill; this model was then used to estimate deformation modulus at the third mine because the earth pressure cells and embedment strain gauges recorded negligible changes. Rockfill binder used at these mines ranged from 4 to 8 per cent of the dry components by weight, the water-to-cement ratio was from 0.42 to1.0, and the largest aggregate size in the three mixes ranged from 5 to12 cm (2 to 4.7 in). The range of the calculated in situ deformation modulus values was large, but as expected, it was bracketed by modulus values for cemented tailings and roller-compacted concrete with similar cement contents and water-to-cement ratios. Dans le cadre d’études sur la sécurité et la stabilité de trois mines souterraines situées aux États-Unis, les chercheurs ont installé des palpeurs de pression des terres et des extensomètres d’encastrement dans les remblais cimentés afin de mesurer les variations relatives à l’effort et à la déformation des terrains durant l’exploitation minière et le chargement du remblai. Les données recueillies à l’aide de ces instruments ont servi au calcul du module in situ du remblai dans deux de ces mines. Le modèle numérique tridimensionnel de la semelle d’un remblai cimenté a été validé à partir des données recueillies par les extensomètres ancrés dans la voûte et dans la semelle de ces mines; ce modèle a ensuite été utilisé pour estimer le module de déformation à la troisième mine, étant donné que les palpeurs de pression des terres et les tensiomètres enfouis avaient relevés des variations négligeables. La matière d’agrégation de l’enrochement utilisée dans ces mines comportait entre 4 % et 8 % des composantes sèches par poids; le rapport eau-ciment se situait entre 0,42 et 1,0; et la taille des agrégats les plus gros dans ces trois mélanges était de 5 cm à 12 cm (2 po à 4,7 po). L’écart entre les valeurs calculées des modules de déformation in situ était grand, mais comme on s’y attendait, cet écart a été compensé par les valeurs modulaires des résidus cimentés et du béton tassé au rouleau avec des teneurs en ciment et des rapports eau-ciment semblables. [Als Teil der Sicherheits- und Stabilitätsstudien an drei Bergwerken in den Vereinigten Staaten von Amerika installierten Forscher Erddruckgeber und Einbindungsdehnungsmesser in zementierter Steinschüttung, um Spannungs- und Dehnungsveränderungen während der fortlaufenden Bergarbeiten und der Belastung der Steinschüttung zu messen. Daten von diesen Instrumenten wurden dazu verwendet, das In-Situ-Modul der Steinschüt-ung für zwei Gruben zu berechnen. Ein dreidimensionales numerisches Modell einer zementierten Steinschüttungsschwelle wurde mit den Daten von den im Grubendach und in der Schwelle verankerten Extensometern validiert; dieses Modell wurde dann dazu eingesetzt, um das Deformationsmodul in der dritten Grube zu schätzen, da die Erddruckgeber und Einbindungsdehnungsmesser nur geringfügige Messabweichungen feststellten. Das in diesen Gruben verwendete Steinschüttungsbindemittel variierte zwischen vier und acht Prozent an Trockenkomponenten nach Gewicht, der Wasser-Zementfaktor betrug zwischen 0,42 und 1,0 und die größte Zuschlagstoff-größe in den drei Mischungen schwankte zwischen fünf und zwölf Zentimetern. Die Reichweite der berechneten Werte des In-Situ-Deformationsmoduls fiel etwas breit aus, aber es fand erwartungsgemäß eine Klammerung der Modulwerte zwischen den Zemen-trückständen und dem durch Walzen verdichteten Beton mit ähnlichem Zementanteil und Wasser-Zementfaktor statt.]

By R. H. Grau

Improving the air quality in metal/nonmetal mines is important in protecting the health of miners. Air quality can be improved in metal/nonmetal mines by developing proper ventilation techniques. Mine ventilation systems require stoppings to direct the airflow and establish pressure differentials throughout the mine. Due to their large size, stoppings in large-opening mines are cumbersome and costly to construct and maintain. As part of its mining health and safety program, the National Institute for Occupational Safety and Health (NIOSH) designed and tested two novel stoppings (Super Stopping and the EZ-Up Curtain Stopping) at its Lake Lynn Laboratory (LLL). The Super Stopping is designed as a long-term permanent stopping for use in the main entries of the mine, while the EZ-Up Curtain Stopping, although very durable, is designed more for portability and ease of installation. This paper describes the design, materials, and construction methods used for these stoppings as well as their performance and durability when subjected to tests simulating actual production face blast pressures.

Jan 1, 2006

To enhance safety and efficiency when moving large mining equipment under energized trolley lines, and to assist in compliance with Section 75.1003.2, 30 CFR. Approach A system was designed, using established technology, that permits a remotely located circuit breaker to be controlled from the cab of a mine locomotive moving large mining equipment under energized trolley lines. This control consists of setting the desired trip current, automatic or manual tripping, resetting, and voice communications between the locomotive and a remote Circuit breaker location. How It Works According to 75.1003.2, 30 CFR, whenever a piece of off-track equipment (such as a longwall chock or a continuous miner) is moved by rail under energized trolley or feeder lines, power for the locomotive that is moving the equipment must come from only one' circuit breaker. This circuit breaker must be adjusted to permit no more than one-half its rated short-circuit current to flow. The intent is to lessen the danger if an accident should occur, and if the equipment contacts the trolley line. Even so, the danger is great. This half setting can still represent many hundreds or even thousands of amperes, enough to endanger personnel, the equipment, or the mine. The Remote Control System reduces this danger substantially by giving the personnel associated with the move total control over the associated circuit breaker. The system as designed, is intended to be used with portable circuit breakers that are pulled on a small flat car by a mine jeep, and either precede or follow the equipment, depending on the direction of the power. This portable circuit breaker is equipped with a commercially available solid state overcurrent relay and associated shunt. This circuit breaker is connected via heavy duty clamps around an open trolley line tie breaker such that the current through the shunt is also the current in the trolley line. A receiver, interfaced with the overcurrent relay and shunt, completes the remote system.

Jan 1, 1981

Control respirable dust in underground coal mines through selection of optimum water spray pressures. Approach Through underground trials at longwall and continuous mining operations, the relationship between operating water spray pressure and respirable dust levels at the machine operator's location was determined. Defining the Application Water sprays are used for two significantly different control applications. On longwall mining machines, sprays are commonly installed both on the body of the machine and on the cutting drum. Sprays on the body of the machine are used to redirect dust which has already become airborne away from the machine operator. Each spray acts as a small fan, directing the primary airflow over and around the machine and towards the face, away from the operator. The energy of this system is directly related to the spray pressure. Higher pressures move more air, but care must be taken not to cause turbulence and boilout into the walkway. Sprays mounted on the drum are, effective at suppressing the respirable dust at the bit/coal interface and preventing it from becoming airborne. Again, these sprays must not impart excessive energy to the dust particles thus stirring up more dust than they suppress. While mounting sprays on the shearer drum is standard industry practice, there is no reliable technology available to successfully mount water sprays on the cutting drum of continuous miners. Instead, sprays are mounted on the machine body, close to the drum, and directed at the cutting head. This allows the water to reach the bit/coal interface and mix with the cut material. Here again, care must be exercised to prevent these sprays from imparting excessive energy to the dust particles and stirring up more dust than they suppress. These sprays can also cause dust "rollback" from the face, toward the operator, if operated at too high pressures.

Jan 1, 1986

To improve efficiency in producing clarified water from mineral and metallurgical processing streams containing suspended particles. Approach Particles suspended in mineral and metallurgical processing streams are filtered out by granular magnesium oxide (MgO) used as the medium in deep bed filters. How It Works MgO is substituted for the silica sand or garnet sand currently used in conventional deep bed filters. These filters presently consist of a 24- to-48-inch-deep layer of either silica sand or mixed media, consisting of a stratified combination of anthracite coal, silica sand, and garnet sand. As waste water containing fine solids is percolated through the granular bed, the suspended particles become attached to the filter grains. When MgO replaces sand as a filter medium, the overall filter capacity is generally increased 50 to 80 percent, and no equipment modifications are necessary for filter operation. MgO is unique because it has a positive surface charge in water while most suspended materials are negative. The attraction of these negatively charged suspended particles to MgO enhances filtering performance. As is necessary for all good media, MgO is insoluble and nontoxic.

Jan 1, 1983

"Fire fighting in metal mines under the best of conditions is a dangerous, a slow, and a difficult task. Certain gases generated from combustible material burning in restricted areas are poisonous, even in small quantities, and can not be breathed without serious and often fatal results. In addition to poisonous gases, smoke is given off which obscures the vision of the fire fighter and frequently prevents him from gaining access to the fire area. Many fire-fighting crews have had to turn back because their vision was so impaired by the dense smoke that the fire area could not be located and there was danger of them becoming lost in the mine.In mines having mechanically controlled ventilation - that is, mines not dependent entirely upon natural air currents - the gas and smoke can be forced ahead of the fire-fighting crews, thereby facilitating exploration of the mine and saving the time, energy and oxygen of the mine rescue apparatus crews.Where currents of fresh air can be circulated up to points near the fire without danger of seriously spreading the fire, fresh air bases can be established in the immediate vicinity, and a more intelligent campaign for fighting or controlling the fire can be mapped out.Positive air currents through forced ventilation may also result in saving the lives of miners who otherwise might have been trapped in smoke and poisonous gases.It is generally known that comparatively few metal mines have attempted to regulate or control air currents, with the result that when a fire occurs underground, the normal ventilation may be reversed, short circuited, or the air current may be in one direction one minute and in the opposite direction the next; or, generally speaking, the ventilation can not be depended upon, and smoke and poisonous gases may accumulate in any part of the mine or ""drift"" on the fire-fighters or on the miners endeavoring to escape."

Apr 1, 1921

By A. B. Hooker

Investigations at the Pittsburgh Experiment Station have shown that the satisfactory operation of aflame safety lamp depends not only upon proper design and assembly of the lamp but upon the kind of fuel used, and that much of the trouble experienced with permissible flame safety lamps at mines is due to the common use of motor gasolines, none of which is suitable in the present types of permissible flame safety laps. This report gives the results of a limited study to determine what satisfactory fuels are available, the specification limits of such fuels, and to suggest modifications of assembly and care of the lamps to improve performance with any satisfactory fuel.

Jan 1, 1938

By M. S. Seehra, R. S. Pandurangi

"A comparative study of the intensities of the IR modes in the pjlotoacoustic and. FrIR spectroscopy of amorphous and crystalline SiO2 particles is presented. It is observed that in photoacoustic spectroscopy of amorphous SiO2, IR modes of surface species are enhanced by over an order of magnitude compared to the bulk IR modes of SiO2. This effect, though not yet understood, may find applications in surface science.Since the publication of the Rosencwaig-Gersho theory of the photoacoustic effect in solids in 1976 [1], a great deal of attention has been paid to the development .of photoacoustic spectroscopy (PAS) into an analytical technique for condensed matter studies, especially when combined with the modern Fourier transform infrared (FTIR) spectrometer [2-8]. PAS has now been applied to a variety of experimental situations [2, 3] and it is particularly suitable for opaque powders and for cases where ~ample preparation (e.g. mixing with KBr as is usually done in FTIR spectroscopy) is not desirable. Another area of interest is the depth profiling feature of PAS, which is studied by varying the modulation frequency of the incident radiation [2-8]. The one-dimensional Rosencwaig-Gersho theory for non-porous samples has been extended to other cases [9-12]. Recently it has become known [11, 12] that for porous samples with porosity the IR modes are enhanced by a factor proportional toe. This enhancement is due to the pressure wave set up in the interstitial gas in the porous sample and this enhancement has been reported by a number of groups [12-14].In this Letter we report the observation of anomalously large enhancement of the PAS signal for certain surface IR modes on the surface of amorphous silica particles. This observation differs from the previous reports in that certain surface modes are enhanced by over an order of magnitude compared to the bulk IR modes. Although the reasons for this enhancement of the surface IR modes in PAS are not understood at present, this observation may open up new approaches to the study of surfaces. Results of these initial observations are given in this Letter. ·Experimental studies reported here were carried out on an FTIR spectrometer (Mattson Instruments, Model Cygnus 100) equipped with an MCT detector. The same instrument was used for PAS studies in conjunction with an MTEC (Model 100) PA cell. The sample cell and the spectrometer are continuously flushed with dry, CO2 free air obtained by the use of Balston Instruments Air Dryer Filter System (Model 75-60). Usually data were collected for 32 scans at 4 cm-I resolution, although both scan and resolution can be varied. For FTIR studies, samples were mixed with IR-grade KBr and pelletised. For PAS, no sample preparation is necessary and data are ratioed against dry carbon black [4, 5]."

Jan 1, 1989

By Robert L. Lagace, N. Albert Moussa

The objective of this project was to perform a preliminary study to determine the desirability/practicality of burying the communication cables in underground mines in order to protect then from the effects of fires and explosions We conducted discussions with Government and industry specialists on the physics of mine fires and explosions, mine disaster fighting, rescue, and investigation activities, and on nine operations. In addition we examined published experimental work and selected detailed NSHA accident reports on fires and explosions in underground mines. We found the overall desirability /practicality of cable burial must be regarded at this time as highly questionable, because of its benefit limitations to special sceneries, its practical operational shortcomings, and the availability of alternative cable protection options.

Jan 2, 1982

By Edward F. Divers

The Bureau of Mines recently tested a sideboard device that is designed to act as an extension of conventional brattice, thus improving face ventilation of developing room-and-pillar-type coal mining. In these laboratory tests, an 8-foot-long rigid sideboard was mounted vertically along the left fender of a full-scale-model ripper-type continuous mining machine, rising to the mine roof to provide an air seal. It extended from the auger support frame pivot point outby along the fender. A novel water spray manifold was used to form an air seal between the sideboard and brattice. Tests showed improvement in face ventilation with the prototype device, and also demonstrated that water sprays can form an effective air seal over a fairly wide pressure range. Based on this preliminary study, subsequent improvements may make the sideboard concept much more effective, thus affording a simple, inexpensive technique to improve the effectiveness of face ventilation.

Jan 1, 1979

Simplify the spraying of sealants onto coal mine roofs. Approach A nonclogging system in which dry-fed sealant is mixed with water down-stream of the spray nozzle, has been developed and tested. How It Works The two-channel nozzle of this spray discharges two separate flows, a mixture of air and dry sealant from a central cylinder, and an encircling spray of water from a concentrically mounted water ring (a ring-shaped manifold). Downstream of the nozzle, the water mixes with the air and sealant to form a wet sealant spray that adheres to mine surfaces with very little rebound. (See photograph.) Extensively modified commercial spray machines are used to feed the sealant to the spray nozzle smoothly, without raising dust. Plugging of the nozzle is practically eliminated by two self-cleaning design features of the nozzle. These are the air gap and the tapered bore of the cylinder, (See drawing.)

Jan 1, 1979