Search Documents

By William H. Schiffbauer

The Bureau of Mines has developed a passive encoder for range knobs, a device that automates the task of obtaining the range settings from devices or instruments to be input to microcomputers. It is easily constructed and installed and will not disrupt the device to which it is being attached. It consists of a custom knob and a small printed circuit board that has light-emitting diodes and magnetic reed switches attached. A ribbon cable connects it to a microcomputer. This encoder eliminates one source of human error in an automated process.

Jan 1, 1983

By H. L. Anthony, A. C. Richardson, G. D. Coe

"INTRODUCTION The Warrior View mine of the Seaboard Coal Corporation is located in Tuscaloosa County on the Warrior River about 14 miles northeast of Tuscaloosa, Ala. The Brookwood bed at this point yields a coal with fair coking qualities, and the product from neighboring mines on this bed has been used for the manufacture of blast furnace coke. The output of the Warrior View mine, however, is used exclusively for domestic and steam-raising purposes.This paper continues the series° of reports on the washability of Alabama coals which are based upon the study of coal preparation in Alabama now being conducted by the U. S. Bureau of Mines and the University of Alabama with the cooperation of the different coal mining companies. This paper contains screen-sizing and float-and-sink tests of a representative sample of run-of-mine coal, and flakiness and crushing tests on certain sizes.Published information on the Brookwood bed is very meager. Fieldner6 gives the proximate and ultimate analyses for a number of seam samples taken from representative mines working this bed. Gandrud and Britton7 show sections of this bed taken at Searles, Ala. They also give the specific gravities of the coal, the bone, and the shale partings.Table 1 give the proximate and ultimate analyses for the 3/4 to 3/16 inch size of raw coal. Table 2 gives the sulphur content and the ash fusibility temperatures of the float-and-sink fractions for this same size. The character of the coal is very uniform throughout the range of sizes produced and, as it was not convenient to have these analyses on all sizes, this size was chosen as being representative of the coal. From the information available it is evident that the coal preparation problem is restricted to one of ash reduction.SAMPLING AT THE MINEAt the Warrior View mine the run-of-mine coal is dumped from the mine cars upon a 3-inch grizzly. The oversize is crushed in rolls set at 24 inches and joins the undersize before being elevated to the raw-coal bin ahead of the jig. The sample was caught at the point where elevates discharges into the raw-coal bin, by taking a proportional amount of the coal at 10-minute intervals over the period of a day's run, The total sample amounting to 2.7 tons was shipped to the laboratory at Tuscaloosa for the washability studies."

May 1, 1932

By T. M. Barczak, S. C. Tadolini

Pumpable roof supports provide an alternative approach to secondary support in underground mining. Unlike all other supports that are either partially or fully prefabricated prior to being transported into the mine, the pumpable support is fabricated in place in the mine entry. This reduces the underground material handling efforts and thus the injuries historically associated with in-mine support construction. On-site fabrication also facilitates application of the support in areas that are inaccessible to transportation equipment such as scoops or rail cars, making it ideal for many bleeder applications. One of the main advantages of the pumpable support is that it fully bridges from the mine floor to the roof, thereby eliminating the requirement of “topping off” the support with wooden wedges or crib blocks that soften most other support responses. This report examines the development of modern pumpable roof support technology and provides a full description of the performance capabilities of each of the support products now on the market.

By Frank H. Reed

This report is one of a series written by members of the Solid Fuels Mission to Germany describing wartime developments in the mining , preparation , and utilization of coal . This mission was organized early in 1945 under the auspices of the Technical Industrial Intelligence Committee , which cooperated with a counterpart British committee . The Solid Fuels Mission operated under the direction of a steering committee headed by Dr. C. J. Potter , Deputy Solid Fuels Administrator . The personnel of the mission consisted of H. F. Yancey, in charge , J. W. Buch, Thomas Fraser , L. L. Newman , and L. D. Schmidt of the Bureau of Mines ; H. H. Lowry , Director of the Coal Research Laboratory , Carnegie Institute of Technology; H. J. Rose , Vice - president and Director of Research , Bituminous Coal Research , Inc .; and F. H. Reed , Chief Chemist , Illinois State Geological Survey . Over 50 reports were written by the members of the Solid Fuels Mission . These , together with microfilms of supporting data obtained in the course of the investigations , are on file at the Bureau of Mines , Washington , D. C. , where they are available for public examination . The Office of the Publication Board in the Department of Commerce is prepared to furnish photolith copies , photostats , or microfilm reproduction of all declassified reports . A Bibliography of Scientific and Industrial Reports is issued weekly by the Department of Commerce , Office of the Publication Board , and is sold by the Superintendent of Documents , Government Printing Office , Washington 25 , D. C. , on a subscription basis . An initial payment of $ 10 will provide for approximately 9 months , and subscribers will be notified when additional remittance is necessary . All subscriptions will begin with volume 1 , No. 1 , unless ordered otherwise . The Bibliography, covers all materials and subjects and gives instructions for obtaining the desired items . The reports of the Solid Fuels Mission relate to the following general subjects : Mining methods in the Ruhr district of Germany , with special reference to mechanical cutting and loading equipment , pneumatic packing , and Diesel mine locomotives ; activities of industrial research laboratories supported by the German coal and coke industry ; coal preparation in western Europe ; low- temperature carbonization processes ; metallurgical coke from

Jun 1, 1948

By Guthrie. R. K., H. B. Hill

"INTRODUCTION During the early 1920's world-wide attention was attracted to a group of oil fields (Mexia, Wortham, Currie, Richard, and Powell) later known as Mexia-Powell fault-line fields in Limestone, Freestonne, and Navarro Counties, Tex. Enormous yields of high-gravity oil from the wells in these fields resulted in drilling campaigns that quickly surpassed all previous records for rapid, intensive development of productive areas. The discovery of oil in the Mexia filed in September 1921 was followed quickly by the finding of oil in the Currie field in October. In January 1923 oil was discovered in the Powell field; in February 1924 the Richland field, midway between Currie and Powell fields, was brought in; and in November 1924 oil was discovered in the Wortham field, situated between Mexia and Currie fields. Each of the fileds was developed rapidly: wells were spaced closely and had high initial production; production peaks were reached early in the producing lives of the fields; subsequent decline was rapid, and there was early and rapid encroachment of edge water.In 1927 Bureau of Mines engineers, in their investigations a engineering conditions in oil,completed a preliminary study and published a mimeographed report 4/ on underground conditions in the Wortham field, and in 1928 they reported on production and development problems in the Powell Field. 5/ field."

Aug 1, 1943

By David S. Yantek

Miners in underground coal mines experience prolonged exposure to high noise levels, often with A-weighted sound levels in excess of 90 dB. Field tests have shown that the continuous miner conveyor is a dominant noise source. This paper will identify the most significant noise-radiating surfaces on the continuous miner tail section using vibration levels and surface areas to estimate the sound power levels of each surface. In addition, using five test cases, this study will examine the effects of three engineering noise controls on the surface-averaged vibration levels and average sound levels measured with four microphones located two meters from the tail section. The noise-radiating surfaces of the conveyor’s tail section include the top and bottom decks, the sideboards, and the flex plates. Emphasis is placed on the changes in the estimated sound power levels in the 500 – 2500 Hz 1/3-octave bands since this frequency range accounts for 80-85% of the sound energy near the tail section. The results show that the bottom deck is the most significant noise radiator for the untreated miner. Installing a coated bottom deck reduces the estimated sound power level radiated from the bottom deck by 11 dB and the average sound level by 2 dB. Using a coated tail roller results in reductions of the estimated sound power levels for individual components from 1 to 4 dBand reduces the average sound level by 2 dB. Coating the slide plate has little effect on both the estimated radiated sound power levels and the average sound level. The test results indicate that modifications that reduce flex plate vibration and reduce energy transfer from the tail roller into the tail section will be effective in reducing noise when combined with a coated tail roller and coated return deck.

Humankind's interest in measurement of human physical strength probably dates to the first humans. At that time, life was truly a struggle in which the fittest survived. To a great extent, fittest meant strongest. Interestingly, current interest in human physical strength in the workplace stems from 1970-1980s vintage research demonstrating that persons with adequate physical strength are less likely to be injured on physically demanding jobs. Survival in many modem workplaces may still be a case of survival of the strongest. There is, however, a flip side to this issue - that persons with limited strength are more likely to be injured on "hard" jobs. To address this problem, we can apply what we know about physical strength to job design. "Hard" jobs can be redesigned to be within the physical strength capability of most people. Since physical strength is important to these jobs, we must find ways to quantify it through testing. This publication concerns human physical strength testing. Its purpose is not to recommend any particular type of testing, but rather to describe the types of testing available and their uses. It is up to each individual user of strength testing to decide which testing technique is most appropriate for his or her particular application. This booklet discusses four types of strength testing: isometric, isoinertial, psychophysical, and isokinetic. Human Strength Before describing the different types of strength measurement, we must define the term "strength" and explain the concept of strength measurement. Strength is defined as the capacity to produce force or torque with voluntary muscle contraction. Maximum strength is defined as the capacity to produce force or torque with a maximum voluntary muscle contraction.(1,2) These definitions include some key words that must be explained. A voluntary muscle contraction is "voluntary." When a person's physical strength is measured, only the effort the person willingly puts forth at the time is measured. Thus, when we test a person's "maximum strength," we are not measuring his or her actual maximum, but some lesser value representing what he or she is comfortable expressing at the time with the existing equipment and environmental conditions. Interestingly, when researchers startled persons being tested (e.g., by setting off a starter's pistol behind them), they have found significant increases in measured strength.(3) It has been hypothesized that the lower strength displayed during normal testing provides a margin of safety against overloading and damaging muscle tissue. The test equipment and the tested person's familiarity with the process also influence the "voluntary" strength output. The interface between the tested person and the test equipment is particularly important. A poorly designed interface induces localized tissue pressures that vary from uncomfortable to painful. In this situation, testers are measuring voluntary discomfort tolerance - not strength. It is important for strength researchers to keep the "voluntary" nature of their data in mind when they are designing their equipment and protocols.

Jan 1, 1998

By William J. Campbell

Three types of X-ray analytical instrumentation were compared for applications in the secondary brass and bronze industry. The instruments were a conventional X-ray spectrograph, a portable X-ray spectrograph, and a radioiso-topic X-ray analyzer using balanced filters. The following two general applications were considered: Rapid identification for sorting scrap metals and quantitative analyses to provide guidance in the melting and casting of alloys. Twenty-three analyzed copper-base alloys were used as standards. Although the alloys varied widely in composition, matrix correction procedures were not necessary except for copper. The conventional X-ray spectrograph provides positive identification of the alloys and quantitative values for the six elements investigated--aluminum, copper, iron, lead, tin, and zinc. Equivalent results were obtained with the portable X-ray spectrograph for those elements whose characteristic X-rays are in the wavelength range of the instrument. The radioisotopic X-ray analyzer distinguishes certain groups of alloys and provides quantitative determinations for copper, lead, tin, and zinc. The sensitivity of the analyzer was marginal for the determination of small concentrations of elements of atomic number 26 or lower.

Jan 1, 1972

By D. Harrington, M. W. Von Bernewitz

"Introduction In studying the mine disaster files of the Bureau of Mires for preparation of a bulletin on coal-mine explosions, a table was compiled covering various features of fan installations and the handling of air currents at the time of and after the disasters. As a sidelight on this discussion, there was tabulated the loss of life and number of men injured.Discussion of collected dataOf the 164 disasters tabulated, 148 were explosions, 14 were fires, and 2 involved both fire and explosion. The total loss of life was 4,158 and 412 were injured. There were 145 disasters in bituminous coal mines, 13 in anthratice mines, 2 in lignite mines, 1 in a cannel coal nine, and 3 in metal mines. By States, 35 took place in Pennsylvania; 17 in West Virginia; 16 in Oklahoma and Alabama; 15 in. Kansas and Illinois; 12 in Indiana; 7 in Colorado; 6 in Kentucky; 3 each in Ohio Tennessee and Wyoming; 2 each in Arkansas, Montana, Washington, Virginia, New Mexico and Utah and 1 each in Iowa, Missouri, Maryland, and California."

Sep 1, 1924

By William R. Barton

COLUMBIUM (niobium) and tantalum are similar refractory metals with closely related properties and uses and close association in ore deposits. Until recently both metals, particularly columbium, were essentially laboratory curiosities. However, since the beginning of World War II, applied technology, under the impetus of national security requirements, has realized many chemical, electronic, nucleonic, and missile and rocketry applications, where high temperature or corrosive environments require the use of columbium or tantalum. At the same time, advances in these fields have resulted in intensive research on the geological distribution, resources, metallurgy, and properties of these two metals; their alloys and compounds; and the development of a full-fledged columbium-tantalum industry. The future appears to promise continued acceleration in such studies and ever-increasing demand for these elements. The raw material supplies of columbium are abundant, and the extractive metallurgy of columbium is well enough advanced to assure adequate supplies of the element at reasonable prices to meet any projected demands. Although the extractive metallurgy of tantalum is similarly well developed, raw material supplies are so limited that, lacking new ore discoveries, an increase in demand to five times the 1959 level would severely tax ore-production facilities. Approximately 120 tons of tantalum and about one-half as much columbium was produced in 1959. Additional quantities are consumed as compounds or additive alloys such as ferrocolumbium and ferrotantalum columbium (55).3

Jan 1, 1962

By J. L. Howell, D. E. Pollock, A. B. Cecala, A. D. O’Brien

Dust from worker,s clothes has been shown to be a problematic source of personal dust exposure. A recently completed effort between NIOSH and the Unimin Corporation has resulted in a quick and effective way to clean worker clothing. The process involves a booth under negative pressure with an air spray manifold to supply compressed air to blow off the dust from the clothing. The overall system is designed to meet MSHA and OSHA requirements. Results of field testing indicated that the manifold cleaned the clothes 10 times faster and removed 50% more dust than cleaning methods used by workers today.

By David A. Lipton

In the summer of 1985, at the request of the U.S. Forest Service, the U.5. Bureau of Mines examined the 109,000-acre West Big Hole study area to evaluate its identified mineral resources. The study area is in Beaverhead County, about 50 mi west of Dillon, MT. Four lode properties within or adjacent to the study area contain an estimated 452,000 tons of identified subeconomic gold-silver resources. Resources ranged from 900 to 302,000 tons, with estimated grades between 0.02 and 0.23 oz/ton gold and as much as 4.8 oz/ton silver. Gold, silver, and base-metal content in samples of poorly exposed mineralized structures indicate that exploration may identify resources on 18 additional lode properties within the study area and 5 properties adjacent to it.

Jan 1, 1988

By Nicholas Kyriazi, John P. Shubilla

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory, has undertaken a study to determine how well self-contained self-rescuers (SCSRs), deployed in accordance with Federal regulations (30 CFR 75.1714), hold up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSRs in the sixth phase of testing from mid-1996 to early 1998. The SCSRs were tested on human subjects and on a breathing and metabolic simulator. These results indicate that most of the apparatus, if they pass their inspection criteria, perform satisfactorily. However, the deployed CSE SR-100s exhibited significantly higher inhaled CO2 levels than new units, as in the previous phase. This will cause higher ventilation rates in most users, which will, in turn, result in higher breathing pressures, possibly causing users to prematurely remove the apparatus. CSE Corp. has developed a noise test that can identify apparatus suffering from chemical-bed degradation causing the early CO2 breakthrough. This test was added to the inspection criteria for the SR-100. In addition, several of the MSA Portal-Packs that passed their inspection criteria were found to have KO2 dust in their mouthpieces. Further investigations by NIOSH and the Mine Safety and Health Administration confirmed these findings, which resulted in the decertification of the apparatus and their removal from service.

Jan 1, 2000

By Sidney Katell

Covering the period from January 1961 through December 1961, this report is a continuation of the series that began with the publication of Information Circular 7516 in October 1949. It is also the third report in the series to be prepared as a cooperative effort by the Bureau of Mines and the American Association of Cost Engineers. The cooperative agreement between the two groups provides for the publication of an annual cost bibliography with the work load involved in the preparation shared equally. The abstracted articles, concerned with all facets of cost engineering in the field of chemical and petroleum plants and related facilities, came from the following sources: 1. A.A.C.E. Bulletin. 2. Bureau of Mines Information Circulars. 3. Bureau of Mines Reports of Investigation. 4. Chemical Engineering. 5. Chemical Engineering Progress. 6. Chemical Week. 7. Coal Age. 8. Coal Utilization. 9. Cost Engineering. 10. Industrial and Engineering Chemistry. 11. Nucleonics 12. Oil and Gas Journal. 13. Petroleum Engineer for Management. 14. Petroleum Refiner. 15. World Oil.

Jan 1, 1962

By L. J. E. Hofer

THIS BULLETIN analyzes and summarizes research at the Bureau of Mines dealing with the preparation, properties, and reactions of iron carbides in the period 1948-60, part of which was sponsored by Wright Air Development Laboratories. The objective was to develop better catalysts for the synthesis of methane and higher hydrocarbons from hydrogen and carbon monoxide. The investigations resulted in the first adequate characterization of epsilon iron carbide, which later proved to be an important intermediate in the tempering of martensite in steel. At temperatures near 170° C, the carbon in carbon monoxide reacts nearly quantitatively with finely divided alpha iron to form an iron carbide in which the metal atoms occupy the positions of the close packed hexagonal arrangement with lattice parameters of ao=2.754 A and co=4.349 A. The carbide has a composition within 2 atomic percent of that required for the formula Fe2C, a Curie point of about 370° C, a specific magnetization of 160.4 ergs per gauss-gram Fe at 50° C, and a ferromagnetic moment of 1.70 Bohr magnetons. Epsilon iron carbide can be converted to chi iron carbide by thermal treatment at 343° C for about 70 hours. The chi iron carbide so formed has a Curie point of 247° C, a specific magnetization of 142.5 ergs per gauss-gram Fe at 50° C, a ferromagnetic moment of 1.72 Bohr magnetons per iron atom, and a paramagnetic moment of 5.5 Bohr rnagnetons per iron atom. Direct synthesis of this carbide from carbon monoxide at 240° C indicates a composition within 7 atomic percent of that required for Fe2C. Chi iron carbide can be converted to cementite at 550° C in about 315 minutes. The theta iron carbide so prepared has a Curie point of 210° C, a specific magnetization of 147.3 ergs per gauss gram Fe at 50° C, a ferromagnetic moment of 1.72 Bohr magnetons per iron atom, and a paramagnetic moment of 3.9 Bohr magnetons per iron atom. Pure chi iron carbide reacts to form theta iron carbide by the elimination of free carbon. In the presence of an excess of free iron in intimate contact with the carbide, chi iron carbide reacts with the free iron to form theta iron carbide. The second reaction proceeds at an appreciable rate at 320° C and can be used to snythesize finely divided theta iron carbide with no free-carbon impurity at low temperatures. The ease of the reaction in the presence of free iron suggests that chi iron carbide is an intermediate in the tempering of epsilon iron carbide to theta iron carbide as it proceeds in steels. Experiments on carbon steel show that the magnetic moment of the iron atoms in martensite is about 2.2 Bohr magnetons per atom, a value approximately the same as that of the iron atoms in alpha iron. The Curie points of epsilon iron carbide, chi iron carbide, and theta iron carbide were found -in various specimens of tempered steel to be 10° to 20° C lower than normal values. This shift is probably the result of manganese in solid solution. Preparations of various compositions of epsilon iron carbonitrides show many effects of extensive isomorphism between epsilon iron carbide and epsilon iron nitride. The action of carbon monoxide on finely divided alpha iron at 400° C results in free carbon deposits containing filaments about 0.1 micron in diameter and several times as long. The filaments are characterized by nuclei of dense material located midway from each end of the filament. Although carbiding to near completion at 240° C over periods of about 300 hours produces a preparation containing no appreciable percentage of epsilon iron carbide, very brief periods of carbiding of the order of a minute result in the formation of detectable epsilon iron carbide even at temperatures as high as 325° C. The data indicate that epsilon iron carbide is an intermediate in the formation of chi iron carbide during its formation from carbon monoxide in the gas phase. Attempts to convert cementite to chi iron carbide by cold work increased the Curie point but did not change the X-ray powder diffraction pattern.

Jan 1, 1966

Many USBM research and information products are available through the systems or formats listed below: Mines FaxBack: Return fax service. 1. Use the touch-tone handset attached to your fax machine's telephone jack. (ISDN [digital] telephones cannot be used with fax machines.) 2. Dial 202/219-3644 3. Listen to the menu options and punch in the number of your selection, using the touch-tone telephone 4. After completing your selection, press the start button on your fax machine. Mines Data: Computer bulletin board. Log on via modem through 202/501-0373, or call 202/501-0406 for technical assistance. CD-ROM: This USBM disk is updated quarterly and sold by GPO's Superintendent of Documents. For information on the latest product, please contact Rodger Wedgeworth, 202/501-9557. Internet/World Wide Web: Text and graphics. Access via PC-based browsing software such as Netscape or Mosaic. Universal Resource Locator (URL) is: http:/www.usbm.gav Internet/Gopher Server: Text and tables only. Using Gopher client software, access via port 70 as follows: gopher.usbm.gav Internet System Administrator: webmaster®usbm.gov (or contact your local System Administrator).

Jan 1, 1995

By Gordon T. Austin

The combined production value of natural abrasives, which consist of tripoli, special silica stone, garnet, and emery, decreased in 1986. Shipments of processed tripoli increased slightly in quantity and 20% in value. Production of garnet, a common iron- aluminum-silicate mineral, decreased 12% in quantity and value. There was a 4% increase in the quantity and an 11% increase in the value of refined garnet shipped when compared with 1985 shipments, a new record high. Production of crude special silica stone decreased 7% in quantity and slightly in value, and shipments of finished special silica stone products decreased slightly in quantity and increased 229% in value. Production of emery, an impure aluminum oxide, increased 77% in quantity and increased 269% in value of product mined and shipped. [ ]

Jan 1, 1988

By Horst Peter Wölfel

The goal of biodynamic models is to simulate the vibration behaviour of the human body. In combination with experimental studies biodynamical models can be a powerful tool for the analysis of the effects of vibration exposure on health [1] and comfort. This paper gives an overview of the state of the art of biodynamic whole-body vibration models of humans, addressing both numerical models and hardware dummies. Method Two approaches are distinguished, the phenomenological and the anatomical, as illustrated in Figure 1. [ ] Phenomenological models aim to reproduce the vibration behaviour of humans with respect to particular physical quantities, chiefly the driving-point impedance at the interface to the seat, and partly with respect to other transfer functions. Discrete systems of masses, springs, and dampers with several degrees of freedom whose topology and parameters are determined by structure- and parameter identification methods are used in the sense that the functions derived from measurements are reproduced as well as possible. This paper provides an evaluation of this methodology and defines its range of application as well as its limits.

Jan 6, 2006

Research personnel from the Bureau of Mines, a representative of the Mine Safety and Health Administration, and research contractors for the Bureau of Mines met with other Government and industry representatives at three seminar locations in December 1980 to discuss the findings and products of Bureau research on mine safety training. The research program is aimed at providing assistance to the mining community in its efforts to reduce industrial-type, human-error accidents through research establishing performance based methods and media for employee training. Research emphasis is directed toward development of baseline materials and instructional models; development of methods for structuring and evaluating health and safety, supervisory, and occupational training; and the continued investigation and application of current learning and simulation technology that could significantly enhance the effectiveness of training opportunities.

Jan 1, 1981

By R. Stefanko

In this report, the use of Penn State Ventilation Simulator (PSU/MVS) for planning and evaluating new coal mine ventilation systems is demonstrated. The simulator's application to evaluate the ventilation system of a coal mine currently under development is discussed. The ventilation system is evaluated for representing development of the mine at the end of 12, 24 and 36 months after mining has begun. The report describes the necessary steps of data input preparation, ventilation network development, analysis of results, modifications to the network, and methods to expand the computer program for networks larger than 550 branches.

Jan 1, 1977