Search Documents

By Kenneth R. Farley

The Bureau of Mines developed a rapid and accurate flame photometric procedure for determining cesium and rubidium in ores and in products associated with the extractive metallurgy of these elements. The effect of associated ions is neutralized by addition of buffer solution; alkali metal effects are neutralized by parallel analyses made on standard solutions similar in composition to the sample being studied. The overall accuracy of the method is within 2.5 pct of the amount of cesium or rubidium present; the range from 1 to 25 pct is the most accurate.

Jan 1, 1966

By R. E. Heithecker, Van A. Mills

"Crude oils are capable of dissolving quantities of gas under pressure. This fact has been known for some time, but questions have arisen as to the effects of gas in solution upon the characteristics of the oil. Previous investigations4 show that gas in solution in an oil affects the viscosity and surface tension of the oil, but the effects on the volume and A. P. I. gravity of the oil have not been known. The results given in this report show that there is a decided change both in volume and in the A. P. I. gravity of the oil due to the solution of the gas in the oil under pressure. As gas is dissolved, the volume of the oil and the A. P. I. gravity increase. The converse of this phenomenon is also true: if the gas is released from a saturated oil, there is a shrinkage in volume and a decrease in A.P.I. gravity due to the release of gas from solution. However, various oils show marked tendencies to retain a portion of the dissolved gas upon releasing the pressure to that of the atmosphere. This retained gas has an appreciable effect on the volume and A. P. I. gravity of the oil because the oil does not resume its initial volume or gravity while it retains dissolved gas. In a sense the oil has been ""freshened"" and will not return to its original or weathered volume until it loses some of the lighter fractions. Wiggins5 has shown that a fresh oil decreases both in volume and in gravity because of the weathering of the lighter fractions while the oil is standing in storage tanks.This paper includes data attained during the determination of volume and gravity correction factors to be applied in the oil recovery investigations of the Bureau of Mines. Three oils having a wide range in gravity were used in determining the correction factors. These oils were from the Bartlesville-Dewey field, Oklahoma, the Seminole field, Oklahoma, and the Inglewood field, California. The same gas that was used in the oil recovery experiments was used throughout this investigation. Determinations were made of the volume and A.P.I. gravity increases resulting from the gas going into solution at 200, 400, 600, 800, and 1,000 pounds pressure; also the increases in the volume and gravity of the oil due to retained gas were determined after the dissolved gas was liberated from solution by releasing the pressure to that of the atmosphere.Samples of residual and liberated gas were taken throughout the investigation in order to study the selective absorption and selective retention by the oil of the various constituents of the gas. The analyses of these gas samples showed that there was selective absorption and selective retention of the constituents of the gas. The tests on Inglewood crude gave the most pronounced example of selective absorption and selective retention of the gas.All of the tests were conducted at a constant temperature of 709F."

Oct 1, 1928

By Jalna R. Zatko

The Bureau of Mines has developed and constructed an apparatus that is capable of measuring concentrations of high-molecular-weight polymers in solution at 10 ppm and less. A means for determining low concentrations of polymeric solutions was devised that was independent of slight fluctuations in solvent quality in order to measure polymers in effluent prior to recycling of the recovered solution. The concentrations of polymers ore related to a measured pressure drop observed during turbulent flow of the solution. Low concentrations of polymers of ethylene oxide and acrylamide (frequently used as flocculants for clay waste systems) in aqueous and salt solutions have been successfully measured on the apparatus constructed by the Bureau.

Jan 1, 1981

By Thomas A. Phillips

The Bureau of dines present, an economic evaluation of its process for the ferric chloride leaching of chalcopyrite concentrate. In this process, chalcopyrite concentrate is leached with ferric chloride solution to extract copper, which is precipitated from the solution by electrolysis while leaving sulfur in the residue. Spent liquor from electrolysis is treated with oxygen to regenerate the ferric chloride leach solution and the sulfur-laden residue is processed to recover the sulfur. A cost estimate was prepared for a plant capable of processing 600 tons of chalcopyrite concentrate per day, 330 days per year. The fixed capital cost, on an early 1.975 basis is $27,831,600 and the estimated operating cost is 9.9 cents, per pound of copper product. In comparison, the estimated operating cost of a smelter equipped with a citrate process plant to recover sulfur is about 13.6 cents per pound of copper product. No charge for chalcopyrite concentrate or credit for recovered byproducts has been included in either operating cost. The ferric chloride leach process, therefore, appears to be economically attractive.

Jan 1, 1976

By James C. Cawley

This report presents results of recent Bureau of Mines research to establish the probability of spark ignition as a function of current (or voltage, for capacitor circuits) for resistive, inductive, and ca-pacitive circuits in 8.3% methane-air atmospheres. The data presented quantify the explosion hazard created when low-power electronic devices catastrophically fail in an explosive mine atmosphere. Previous litera-ture dealt with levels of probability between 10-3 and 10-4. This re-port extends the probability data to levels as low as 10-7. This study has verified that when the probability of ignition, PI, is plotted on a log-log coordinate system versus the current (or voltage), a continuous, straight-line relationship is formed. An interesting result that can be statistically hypothesized is that at some low level of igniting current the ignition process ceases altogether.

Jan 1, 1988

By J. I. Paige

The effect of fluoride inclusions on the properties of titanium produced from the Bureau of Mines developed induction slag melting process is of concern to members of the titanium industry. The objective of the research was to determine the effect of CaF2 inclusions on the properties of titanium and its survival rate during melting. The data were obtained from single induction-slag-melted ingots prepared with the normal addition of 4 pct and also with 2- and 1-pct additions of CaF2 slag. The results of this effort showed that the mechanical properties of single-induction-slag-melted Ti-6Al-4V alloy exceed the minimum values specified in Aerospace Materials Specification for Titanium Alloy Bars and Forgings AMS4928H, but these materials are much more notch sensitive in fatigue than normal Ti-6A1-4V alloy titanium. First and second vacuum-arc remelts of single-induction-slag-melted ingots fragmented and increased the number of inclusions, while reductions in the amount of flux resulted in an upward trend in the spatial distance between pores in an x-y plane.

Jan 1, 1988

By H. H. Schrenk, W. P. Yant, P. H. Mautz

"In a study of the chemistry and pathology of chronic benzene poisoning, which was conducted cooperatively by the United. States Bureau of Mines, the Barrett Co., and the producers of benzene, it was necessary to make quantitative determinatious of the abzorption, distribution, and: fate of benzene in the organism. Although methods for determining benzene in relatively large amounts were available no satisfactory method was found for removing and determining the small amounts that are present in the tissues or excretions after exposure to conditions which ultimately cause chronic poisoning. This no doubt accounts for the lack of information in the literature on this particular phase of benzene poisoning.The writers have found in work that will be described in a subsequent publication that the amounts of benzene present in the tissues and excretions under conditions of exposure which produce chronic benzene poisoning arc of the order of a fraction to a few milligrams per 100 grams of tissue. This report describes a method developed and found satisfactory for these determina¬tions.RÉSUMÉ OF PERVIOUS METHODSA method for the determination of benzene in tissue was developed by Joachimoglu. 5 In the Joachimoglu procedure the ground organs are mixed with water and acidified with diluted sulphuzic acid, and the benzene is distilled into a receiver containing carbon tetrachloride. The benzene is nitrated in the carbon tetrachloride, the carbon tetrachloride evaporated, the acid mix¬ture neutralized, and the dinitrobenzene extracted with ether. After removal of the ether the dinitrobeuzene is determined gravimetrically. Joachimoglu reports that this method is about 55 to 60 percent quantitative."

Aug 1, 1935

By R. V. Ramani, R. Bhaskar

"IntroductionThe behavior of dust clouds in mine atmospheres has been a subject of longstanding interest due to both health and safety reasons. Pioneering studies in Germany and SMRE focussed on ambient dust concentration, principally aimed at determining optimum velocities for effective dilution. A summary of studies related to this area is provided by Hall,(l) Efforts to understand dust deposition from the explosion hazard point of view led to experiments in return airways (2-4) followed by experiments in longwalls.(5) Concerted efforts, either experimental or theoretical, were not made until recently to relate ambient concentration with dust deposition in mines. In 1974 Hwang et a1 (6) developed a computer model to predict dust concentration which considered deposition-concentration relationships. Also, experimental studies involving concurrent dust deposition and ambient concentration were conducted in the U.S. by Courtney et al (7 ) in operating mines. Efforts to relate theory with experimental results have been made by Owen (8) and Hwang et al (6 ) for dust deposition. There has been limited work, however, to determine the application of the theories and assumptions from aerosol sciences for modeling dust flows in mine atmospheres. (9 ) This is the objective of the work currently underway in the Generic Technology Center on Respirable Dust since· 1983 under a project titled, ""Prediction of Ambient Dust Concentration in Mine Atmospheres."" The scope of the project activities include:1. Development of a mathematical model to predict dust deposition and concentration in mine atmospheres.2. Experimental studies on dust transport and deposition in mine airways.3. Comparison of the model results with the experimental data."

Mar 1, 1989

By Kevin Ashley

Because toxicities may differ for Cr(VI) compounds of varying solubility, some countries and organizations have promulgated different occupational exposure limits (OELs) for soluble and insoluble hexavalent chromium (Cr(VI)) compounds, and analytical methods are needed to determine these species in workplace air samples. To address this need, international standard methods ASTM D6832 and ISO 16740 have been published that describe sequential extraction techniques for soluble and insoluble Cr(VI) in samples collected from occupational settings. However, no published performance data were previously available for these Cr(VI) sequential extraction procedures. In this work, the sequential extraction methods outlined in the relevant international standards were investigated. The procedures tested involved the use of either deionized water or an ammonium sulfate/ ammonium hydroxide buffer solution to target soluble Cr(VI) species. This was followed by extraction in a sodium carbonate/sodium hydroxide buffer solution to dissolve insoluble Cr(VI) compounds. Three-step sequential extraction with (1) water, (2) sulfate buffer and (3) carbonate buffer was also investigated. Sequential extractions were carried out on spiked samples of soluble, sparingly soluble and insoluble Cr(VI) compounds, and analyses were then generally carried out by using the diphenylcarbazide method. Similar experiments were performed on paint pigment samples and on airborne particulate ?lter samples collected from stainless steel welding. Potential interferences from soluble and insoluble Cr(III) compounds, as well as from Fe(II), were investigated. Interferences from Cr(III) species were generally absent, while the presence of Fe(II) resulted in low Cr(VI) recoveries. Two-step sequential extraction of spiked samples with (?rst) either water or sulfate buffer, and then carbonate buffer, yielded quantitative recoveries of soluble Cr(VI) and insoluble Cr(VI), respectively. Three-step sequential extraction gave excessively high recoveries of soluble Cr(VI), low recoveries of sparingly soluble Cr(VI), and quantitative recoveries of insoluble Cr(VI). Experiments on paint pigment samples using two-step extraction with water and carbonate buffer yielded varying percentages of relative fractions of soluble and insoluble Cr(VI). Sequential extractions of stainless steel welding fume air ?lter samples demonstrated the predominance of soluble Cr(VI) compounds in such samples. The performance data obtained in this work support the Cr(VI) sequential extraction procedures described in the international standards.

Jan 1, 2009

By E. C. Tarpley, H. M. Cooper, R. F. Abernethy

The standard method of employing preliminary air-drying to determine the moisture in coal has been criticized with respect to the loss of heating value from excessive air-drying. By this method, the coal is air-dried at approximately 10-15° above room temperature with the loss in weight being less than 0.1 percent per hour, and then the residual moisture at 105°C is determined. The total moisture is calculated from these two values.

Feb 1, 1948

By J. C. Meeks, C. L. Klingman

An instrument that is sensitive , portable , safe , and low in cost was developed by the Bureau of Mines for detecting helium leaks by comparing the thermal conductivity and flow rate of the atmosphere around the suspected leak against a reference of helium- free air . A vacuum pump pulls the sample gas through a restriction and over thermistor elements , the combined electrical output of which is affected by thermal conductivity and flow rate of the sample gas . Tests showed that the battery - operated Helium Leak Detector was effective and rugged instrument that could be operated safely in explosive atmospheres . The instrument could also detect , but not identify , other gases such as methane , hydrogen , argon , carbon dioxide , and Freon 12 .

Jan 1, 1964

By Daryl R. Tweeton

The Bureau of Mines compared the effects of surface-active chemicals with those of pure water on core-drilling rock and quartz and on fracturing quartz. The objectives were to determine if these chemicals assist drilling and fracturing rock and if zeta potential control was worth pursuing as an aid to full-scale drilling. All tests were performed in the laboratory. No significant increases in drilling rates were observed for 1 to 10,000 ppm Al (as AlC13) in flushing water when drilling microcline or serpentine, nor for 1 to 10,000 ppm Mg (as MgC12) when drilling microcline or marble. Concentrations near those giving a zero zeta potential were used with microcline and marble. A 50-pct rate increase was observed for drilling quartz in 0.7 ppm oleylammonium acetate, which gave a zero zeta potential. No other concentrations were used. No effect on the tensile strength of quartz thread in 0.05 ppm Al (as AlC13), which gave a zero zeta potential, was observed. Heptanol, reported to give a zero zeta potential on quartz, did not reduce the bending strength of small quartz bars below that in water. These generally negative findings raise doubt about the usefulness of zeta potential control in full-scale drilling. The results, combined with previous studies, suggest that controlling physical properties of drilling fluids, such as viscosity, is more useful than altering chemical properties.

Jan 1, 1976

By H. W. St. Clair

In about 1930, Degussa applied for a patent on a process for the of oxides, carbides, sulfides, and other nonmetallic impurities by filtration in the molter state. The filtering media listed were wire screen, coke, and ceramic materials, and quartz. It was also suggested that filtration might be combined with chemical reaction between the metal and the filter medium or that might be added to the system. No patent was granted on the general scheme, but several years later a patent was granted on a continuous process purification of crude light metals, especially or alkali earth and their alloys. The melt was stirred at 1 temperature at which the impurities (such as oxides and salts) remained solid and the metal was drawn through a filter tube. The impurities collected under the filter and were removed by a screw conveyor. Crude sodium was purified by this process in Degussa's Knapsack plant. During the last war, when the refining of scrap became a very urgent Problem in Germany, experimental investigations were extended to separation of other metals and metallic compounds by filtration. Preliminary experiments seemed to confirm the opinion of Dr. L. Weiss that the principles of wet chemical filtration might be applied to a great extent in the purification of metal and alloys.

Jan 1, 1949

By C. E. Julihn

In the fall of 1933 a new discovery of gold was made in the old Mojave mining district of California about 70 miles north of Los Angeles. It led to mining operations that have surpassed in their results all reasonable expectations and are of exceptional promise for the future. In less than 3 years, exploration has opened up a number of veins, from some of which a substantial amount of high-grade ore has been shipped, while a large tonnage of milling ore has been disclosed. Two mills, operating on ore averaging better than $12 a ton, will probably produce more than a million dollars worth of gold in 1936, and a considerable increase of their output in the following year is anticipated. While continuance of these operations for a number of years is already assured by ample reserves of ore, future discoveries of still other veins are reasonably possible, as occurrence of gold throughout the volcanic rocks of the district is widespread and the veins now being mined showed little to attract attention at the surface.

Jan 1, 1937

Objective As mines become safer and disasters fewer, a time may come when no employees in the mining industry have any practical experience in managing a mine emergency. To fill an emerging gap in mine emergency response training, a multidisciplinary team of researchers and computer programmers from the NIOSH Pittsburgh Research Laboratory has developed an intervention for mining personnel who would be in leadership positions in the command center during emergencies. It is called MERITS, a computer-based emergency simulation exercise. MERITS is short for "Mine Emergency Response Interactive Training Simulation." It provides trainees an opportunity to gain command center experience during a simulated underground coal mine emergency. MERITS allows trainees to practice information gathering, situation assessment, decision-making, and coordination skills without risk to personnel or property. Individuals representing mine emergency response personnel, various State safety officials, and private mine management from three States have participated in MERITS training. What Is MERITS? MERITS is an extension of previous work that compiled a knowledge base relevant to mine disaster management via interviews, analysis of literature, reviews of past events, and observations of mock mine disasters. Findings from prior research found a need for an alternative method of command center training. This new computer simulation is being used to train emergency command center personnel to effectively manage an underground mine fire. Modeled after training simulations developed for other industries (e.g., to address nuclear accidents, chemical spills, evacuations, etc.), MERITS simulates underground and surface events related to the disaster. It exposes the user to events that typically occur during a mine emergency, such as lack of information and miscommunication. It also presents trainees with issues that must be addressed, such as making provisions for briefing news media and victims' families, ordering needed supplies, interfacing with Government enforcement agencies, and housing mine rescue teams. The outcome of the scenario is determined by the users' decisions and their emergency response plans. Field Results Field testing of MERITS was conducted with eight full-day training sessions at four different locations in Colorado, Pennsylvania, and West Virginia. These field tests benefited from the knowledge and experience of State of Pennsylvania inspection officials, representatives of the United Mine Workers of America(UMWA), and private mine management who served as trainees for the MERITS training sessions. Trainees self-reported an average of20 years of work experience in the mining industry. All trainees had participated in Mine Emergency Response Development (MERD) training exercises, and many had been involved in real mine emergencies. Trainee evaluation of the MERITS program is summarized below: •Twenty-six of the 27 trainees believed that the MERITS simulation helped them know how to prepare for a real emergency. •Twenty-five of the 27 trainees believed that the storyline for the MERITS simulation was either "very realistic" or "realistic." •All 27 trainees believed that the MERITS simulation helped them learn how to better handle a real emergency. •None of the 27 trainees stated that they were bored during the simulation. After the initial field tests, MERITS was refined and retested during training sessions for individuals from State agencies, the UMWA, and private industry. Mining personnel from underground coal and underground stone mines participated and responded positively to the learning experience. Technology Transfer Industry introduction to the MERITS program will occur throughout 2002. MERITS presentations at the Joseph A. Holmes Safety Association National Meeting in Virginia Beach, VA, in June.

Jun 1, 2002

By Henry J. Kellner, Michael J. Brnich

This U.S. Bureau of Mines report addresses issues involved in using a limited number of training apparatus to give hands-on self-contained self-rescuer (SCSR) training to a succession of miners, and provides guidance regarding methods for minimizing the spread of infectious diseases. Procedures used for preventing the spread of infectious organisms in dentistry, cardiopulmonary resuscitation (CPR) training, and scuba training are examined. The sanitizing methods of three organizations that require individuals to insert the mouthpiece as part of the SCSR donning sequence are discussed. It was found that each of these organizations was able to render their mouthpiece assemblies microbe free simply and inexpensively.

Jan 1, 1989

By Oliver Bowles

This report covers the character, properties, origin, occurrence, and uses of the traprocks and describes briefly the methods and equipment employed in quarrying and preparing them for market. Production of traprock occupies an important place in industry. In 1960 the output in the form of crushed stone reached nearly 58 million tons valued at $87 million. Traprocks are also shaped into blocks of dimension stone for monuments, building construction and decoration, and specialized products such as surface plates.

Jan 1, 1963

By J. Hamilton Duffy

This is the first of, a series of papers describing dredging methods and costs in recovering sand and gravel from the beds of rivers throughout the United States and deals directly with the methods employed and costs obtained by the Ohio River Sand Co. near Louisville, Ky. ACKNOWLEDGMENTS The author wishes to acknowledge the assistance of J. R. Thoenen, mining engineer of the Bureau of Mines, in the collection of data and compilation of this report.

Jan 1, 1931

By Fred N. Kissell

Air recirculation caused by dust scrubbers at coal mine working faces was examined by the Federal Bureau of Mines with regard to the potential hazards caused by a possible buildup of methane gas. A theoretical analysis indicated that there was no apriori way to predict the effect of scrubber recirculation on methane concentration levels. Experiments conducted in a full-scale model of a working face area indicated that methane levels were dependent to a great extent on the location of the scrubber exhaust, but that the scrubber recirculation did not substantially increase the methane concentration above those levels that would have prevailed were the scrubber not in operation. An analysis of two underground scrubber trials showed that the scrubbers had no significant effect on methane levels, and a review of explosions attributed to recirculation showed that these were characterized by a lack of fresh air as well as recirculation. It was concluded that high methane levels are due more to a lack of fresh air than to recirculation.

Jan 1, 1975

By P. M. Gruzensky

A survey of the literature has been made covering the extraction of bismuth from raw materials, its separation from lead, and its subsequent refining. The use of aqueous, nonaqueous, and fused electrolytes in electrolytic refining is reviewed. This literature survey has been prepared preliminary to some proposed investigations concerning the electrometallurgy of bismuth, and, although an effort has been made to cover a majority of the applicable references, a critical review was not attempted and no assertion is made that this manuscript is exhaustive in nature. Titles of publications in parenthesis are translations from the language in which the reference was originally published.

Jan 1, 1954