Search Documents

By V. R. Shea-Albin

This U.S. Bureau of Mines report discusses elastic wave velocity and attenuation behavior as an indicator for changes in load and structural integrity of coal samples. Measuring changes in compressional (P)-wave and shear (S)-wave attenuation and velocity under uniaxial and triaxial compression tests revealed their effectiveness for distinguishing changes in applied load and structural failure of samples. The velocity and attenuation values were used in further calculations such as ratios of P-wave to S-wave values, dynamic elastic constants, normalized velocities, and attenuation coefficients to reveal trends for loading and failure. The behavior of both P-wave and S-wave attenuation and velocity together define distinct and consistent phases of load change and failure for uniaxial and triaxial tests. The S-wave velocity and attenuation illustrate changing axial load and initial development of microfractures within the sample preceding structural failure more clearly than those of the P-wave. The attenuation and velocity ratios and dynamic elastic constants (except the bulk modulus) respond to closure of small preexisting fractures within the coal sample with initial loading to failure of coal samples. The attenuation coefficients and normalized velocities reveal trends similar to those shown by velocity and attenuation.

Jan 1, 2010

By R. D. Groves

Techniques were developed for preparing metallurgical-grade copper powder from industrially produced cement copper. Flotation was used for rejecting discrete gangue particles, acid leaching to remove residual iron and aluminum, hydrogen reduction to eliminate oxygen, sintering to consolidate the fine-sized copper, and grinding to obtain copper powder. Powders prepared from six different cement copper samples contained, in percent, 98.5 to 99.0 Cu, 0.10 to 0.05 Fe, 0.10 to 0.08 insoluble material and the remaining individual impurities less than 0.15 percent. The apparent density, flow characteristics, and other physical properties were suitable for powder metallurgy applications. An economic evaluation showed that this process was economically feasible. Processing costs appeared modest when considering that copper powder commands a price normally about 17.5 cents per pound over that of electrolytic copper.

Jan 1, 1971

By Don B. Hunter

The Bureau of Mines investigated the extraction of alumina from calcined kaolin by leaching with boiling RCI in a train of three 50-gal continuous, stirred reactors. Slurry discharged from the reactors con-tained an excessive amount of fines, which impeded solid-liquid separation. Autogenous grinding of coarse solids that accumulated in the reactors was the source of the fines. This report describes modifications to the reactors and to the operations that led to decreased fines generation and improved solid-liquid separation. Modifications to the reactors included custom-made impellers, the addition of a baffle system, a subsurface slurry discharge system, and slower rotation of the impellers. Concurrent testing of a continuous horizontal belt filter showed that the form filtration rates were increased from 350 to almost 1,000 Ib/h+ ft-2 when the modified reactors were used.

Jan 1, 1984

By Michael J. Magyar

The Federal Bureau of Mines has developed a hydrametallurgical method to recover aluminum, aluminum oxide, and fluxing salts from aluminum salt slags. The slag is leached with water at room temperature to produce a saturated brine slurry. Screening of the slurry yields an aluminum-rich fraction that can be returned to the dross furnace. The remaining slurry is vacuum filtered, yielding a clear brine solution and an aluminum oxide filter cake. Evaporation of the clear filtrate produces a high-purity fluxing salt for reuse in the dross furnace. Over 80 pct of the metallic aluminum is recovered in the aluminum-rich oversize fraction, while essentially all the fluxing salts are recovered by evaporation. This report contains the final results of an investigation on a process research unit scale, an economic evaluation of the method, and recommendations to further improve the process.

Jan 1, 1979

By Paul Biggs

This Bureau of Mines report provides information on 138 waterflood projects in Wyoming. Injection was in 25 producing zones and 65 fields. Specific data presented include field location, discovery and development, water supply and injection, oil and water production, estimates of oil in place, and oil recoveries by primary and secondary methods. The 138 projects studied will, if successful, recover about 800 million barrels of secondary oil. Almost all of the injection water is from deep water wells.

Jan 1, 1970

By Stanton L. Tainter

When the disruption of gold mining stopped the usual source of siliceous flux needed by copper smelters , sandstone copper deposits in northern Arizona offered possibilities as a source of the flux during the war emergency . The Federal Geological Survey , while making a comprehensive survey of sandstone copper deposits , investigated the Warm Springs mining district in northcentral Coconino County in August 1943. A month later , J. H. Hedges , chief of the Tucson Division , Mining Branch , Bureau of Mines , examined the operations in connection with an application for an access road . Both investigations concluded that the district , as an emergency source of copper-bearing siliceous flux , had considerable merit , provided high prices for copper continued in effect . Early in 1944 , V. M. Ryan and S. B. Atherley requested assistance from the Bureau in exploring various deposits on their property . The Bureau / drilled 152 holes , aggregating 3,756 feet , on the Petoskey and Mackin groups of claims . This report is based upon churn drilling done under contract from October 7 to November 25 , 1944 .

Feb 1, 1947

This manual provides instructions for installing, operating, and maintaining a protective canopy on the Galis Mfg. Co. roof drill. The instructions are based upon two actual installations: one made in a mine on roof drill, model 300, and one in the factory. The parts list and engineering drawings for the protective canopy are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other roof drills with similar protective canopies. Skilled mechanics can determine if the instructions herein would be applicable to the other roof drills and can determine any necessary modifications if they are not.

Jan 1, 1973

By M. H. Kline

The Scarlet mine, in Randolph County, N. C., was operated on a small scale at intervals from 1899 to 1915, but no records of the quantity of ore produced are available. J. I. Moore unwatered the mine in March 1948, and Bureau of Mines' engineers examined the underground workings. Several assays checked previous sampling of the mine and indicated a small but comparatively high-grade copper-zinc deposit. The high metal content of the veins and the possibility of developing additional reserves prompted the Bureau of-Mines to drill three holes, totaling 530 feet, at the deposit during March and April 1948. Drilling disclosed that the mineralized vein did not extend over 300 feet along the strike and is probably limited in depth to the contact with the granite mylonite.

Jan 1, 1949

By J. R. Ross

The extraction and recovery of nitrate from waste solutions generated in the production of titanium were investigated using solvent extraction techniques. Laboratory studies and continuous tests in a small solvent-extraction system showed that up to 98 percent of the nitrate can be selectively extracted by a solution of tributyl phosphate in kerosine. The extracted nitrate can be recovered as nitric acid, at concentrations suitable for reuse, by stripping the loaded organic with water.

Jan 1, 1973

By George H. Schnakenberg

This Bureau of Mines publication describes a passive personal sampling device for N02 in air, developed by the New York University Medical Center under Bureau Grant G0133066. The sampler has been successfully demonstrated in the field and in the laboratory. In corroborative laboratory trials the agreement with reference method is excellent. The overall accuracy is approximately ±5 pct of reading to a precision of about ±l pct. All evidence indicates that these samplers should indicate the time-weighted-average N02 concentration to the above accuracy and precision equally well in the field since effects of wind velocity and relative humidity are negligible and the effects of temperature are about 0.1 pct per °F. The duration of exposure and the approximate temperature are the only data that need to be collected in the field. A two-step analysis procedure in field or service laboratory is then used to obtain the total cumulated exposure to N02 in parts per million-hours (ppm times hours), which can be converted to the time-weighted-average concentration of N02 in ppm by dividing cumulated exposure by the duration of the exposure.

Jan 1, 1976

By A. E. Raddatz

Previous Bureau of Mines research has shown that tungsten ores containing as little as 40 pct W032-can be processed by a high-temperature molten-salt extraction technique to produce a tungstate-bearing sodium chloride phase with 99 pct W recovery and little impurity contamination. The objective of this work was to demonstrate that the tungstate-bearing sodium chloride phase can be a suitable feed material for preparing am-monium paratungstate (APT) by a modification to the present industrial solvent extraction process. A combined crossflow-count·ercurrent flow solvent extraction technique to extract tungsten is presented. APT produced by this new technique contained 88.6 pct W032-and the following impurities, in percent: Mn02_ 0.0007, Mo02 0.017, P205 <0.010, and Si02 0.012. Implementation of this processing technique would improve tungsten recovery from concentrates and simplify processing operations.

Jan 1, 1988

By R. V. Lundquist, H. Leitch

Two hydrated calcium aluminates , formed by side reactions in the leaching step and desilication step of the lime- soda sinter process , were investigated to better define their influence on alumina recovery . The two calcium aluminates , Caз [ Al ( OH) 6 ]₂ and зCa0.Al½ 03 · ( 8-12 ) H₂ ) , were prepared and identified by chemical and X- ray analysis . The relative proportions of each of these compounds formed in typical leach solutions at several temperatures were determined . The influence of free lime as a promoter of calcium aluminate formation was also investigated . The formation and precipitation from leach liquors of calcium aluminates contributes to the low alumina recoveries in the process . The presence of carbonate ion in the leach solution suppresses calcium aluminate formation and precipitation and results in higher alumina recovery . Hydrated calcium aluminates are formed in the aging of lime - soda sinters in the normal atmosphere .

Jan 1, 1963

By William C. Henkes

Anticipating the availability of space-altitude imagery from the Earth Resource Technology Satellites (ERTS), the Bureau of Mines investigated the possibilities of using suck imagery in its activities in solid waste disposal, reclamation of mine workings, and mineral resource inventory. The study indicates that monitoring open pit and strip-mining operations can be done using conventional techniques if the sharpness of the imagery is sufficiently high. Possibilities also exist for semi-automated processes for change detection. Additional experimentation is needed for multispectral discrimination and identification of mine-related phenomena.

Jan 1, 1971

By Gilbert M. Farrior

The electrical resistivity the coefficient of electrical resistivity the Hall coefficient, and the absolute thermoelectric power were determined in this Bureau of Mines investigation for nine compositions of the TiB2-CrB2 sub-system. The numerical values of the electrical resistivity and the thermo-electric power were greater for the intermediate compositions than for the end members. The absolute values of the Hall coefficients and the coefficients of electrical resistivity were less for the intermediate compositions than for the end members. The electrical resistivities and Hall coefficients were about the order of magnitude of most metals--from 34 to 202 microhm-cm and from about 0 to -23.3 X 10-4 cuP/coulomb. The thermoelectric power was somewhat greater than that of most metals--up to 15.6 microvolts per 0 C.

Jan 1, 1965

By F. E. Block

The reaction between calcined dolomite and ferrosilicon has been studies with the aim of developing a continuous process for magnesium production. Small-scale tests were made in vacuum retorts similar to those used in the vacuum retort process as developed by Pidgeon (1)2/ and operated during the period of World War II in several Government-owned plants. Factors investigated with respect to the silicon efficiency were the reaction temperature, reaction time, amount of excess dolomite in the charge, and effect of adding sodium silicate to the charge to serve as a binder. Additional laboratory tests were made to study the reaction at elevated temperature but at atmospheric pressure. Silicon efficiencies exceeding 80 percent were found to result when operating in the temperature range from 1,750° to 1,800° C. for periods of 20 to 30 minutes.

Jan 1, 1956

By R. Hogg

"The basic population balance models for agglomeration processes are reviewed and procedures are described for extending their applicability to systems with size-dependent rate constants and to the formation and growth of porous agglomerates from rigid, solid-particles. Simplified procedures for the further extension of the models to include simultaneous agglomerate growth and breakage are also described.INTRODUCTION The association of small particles into clusters or agglomerates is a significant factor in many facets of particle processing. Agglomeration processes are widely used to facilitate handling, storage and utilization of fine powders. Processes such as coagulation or flocculation are used to aid solid-fluid separation in dispersed particulate systems. Agglomeration also occurs as an accompaniment, often unwanted, to other particulate processing operations such as fine grinding, mixing and blending, transport and flow.Reliable agglomeration models are needed for improved understanding of the processes in general and of the complex role of numerous, interacting variables as well as for direct application to the design and control of industrial processes such as flocculation, granulation and pelletization. Ideally, the models should account for the primary forces responsible for agglomerate formation and growth, the effects of external forces on process dynamics, the development of agglomerate structure and its role in the process itself, and the effects of concurrent processes such as structure modification (e.g. compaction) and agglomerate breakage or degradation."

Jan 1, 1989

By H. L. Burmeister

This report describes the mining and milling practices used by the Eastern Magnesia Talc Co. at its Johnson, Vt., operation. The report also contains a description of the local geology and all available information on cost and performance data. Since 1925 the mine has produced continuously at an average annual rate of 54,000 tons, and the ratio of ore hoisted to finished product is roughly 2 to 1. Ore is stoped by a combination of shrinkage and sublevel methods. In any 24-hour period the mill produces an average total of 14 grades of finished talc product, 9 by dry grinding and air classification and 5 by wet grinding and flotation methods. The mine operates one shift per day, 5 days per week and the mill operates on a 3-shift, 5-1/2-day-per-week basis. Operating costs for 1958, on a percentage basis, were mining, 22.34; milling, 54.77; ore haulage, 2.89; and all other, 20.00 percent.

Jan 1, 1963

By M. J. Spendlove

A progress report is presented on a research program in which an attempt was made to develop a practical sulfide-volatilization process for recovering tin from low-grade Bolivian ores. Shaft-furnace designs and operating techniques were studied in a series of experiments in which the objective was to sulfidize cassiterite to stannous sulfide, remove the stannous sulfide by volatilization, reconvert the stannous sulfide to stannous oxide, and collect the resulting fume. A shaft furnace was developed and operated in a final test in which many of the previous difficulties were surmounted. Since the supporting funds were exhausted at this point, the project was discontinued; recommendations for further improvements in furnace design and operation were made on the basis of interpretation of experimental results obtained in shaft-furnace experiments and other related studies.

Jan 1, 1955

By B. W. Jong

As part of the Bureau of Mines program to develop substitutes for critical and strategic materials for metallurgical applications, the Tuscaloosa Research Center has evaluated the effect of additives and starting materials on the sintering and strength properties of sialon (silicon-aluminum-oxynitride) compositions fabricated by conventional pressing and sintering techniques. Sintering and MOR (modulus of rupture) data were developed for sialon compositions produced from three components, Si3N4, A1203, and AIN. When doped with Y203 to aid in sintering, the highest MOR values were obtained with compositions containing between 20 and 30 mole-pet (A1203 + AIN). The effect of the crystalline phase of the Si3N4 and Al203 used in the three-component system on MOR also was investigated. Alpha-Si3N4 and ?-A1203 were found to be the best starting materials. A sialon composed of 67.4 mole-pct a-Si3N4 plus 32.6 mole-pct (?-AI203 + AIN), doped with 5 wt pct Y203, had MOR values at 25°, 1,200°, and 1,400° C of 40,300, 40,300, and 31,100 psi, respectively. Samples of this composition doped with Gd203, MgO, Zr02, and ZrSi04 also were evaluated. The ZrSi04-doped sialon had higher MOR values than Gd203-, MgO-, and Zr02-doped materials but lower MOR values than the Y203-doped sialon. The MOR values of ZrSi04-doped sialons were 25,000 and 25,900 psi, respectively, at 25° and 1,400° C.

Jan 1, 1981

By P. G. Clites

This bulletin summarizes the results of Bureau of Mines research on the development of the inductoslag melting process. Inductoslag melting is an induction melting technique using a segmented, water-cooled, copper crucible. The process was developed as part of the Bureau&apos;s work on effective utilization of reactive metal scrap, and the process has been applied to melting Ti, Zr, Cr, Co, Fe, Ni, and V. Construction details are given for the segmented crucibles and for both an ingot furnace and a casting furnace. The melting process is described, and results of tests conducted with a variety of reactive metals are given.

Jan 1, 1982