Search Documents

By William L. Crentz

Pike County in the easternmost portion of Kentucky is one of the major coal-producing areas in the eastern Kentucky coal field. The county contains numerous coal beds, many of which are too thin to support mining. The commercially important beds are usually 4 feet or more thick, but selective mining at some places calls for removal of a much thinner section of the bed. The variation in quality of the beds from place to place and the large number of coal beds make correlation uncertain. Samples were collected from 14 different coal beds, of which the Elkhorn group is by far the most important. In addition to the Upper Elkhorn No. 3, Upper Elkhorn No. 2, Upper Elkhorn No. 1, and Lower Elkhorn beds that comprise the Elkhorn group, the Winifrede, Williamson, and Bingham beds constitute the principal coal deposits in Pike County.

Jan 1, 1952

By D. Harrington

The desirability of efficient control of air currents, and the necessity of supplying metal-mine workers with better and safer working conditions, has created an active interest in metal-mine ventilation, especially in recent years. This paper discusses the subject both with regard to efficiency and economy, as well as safety and health. It is based on personal observations of the writer from over four year's study of metal mines in six States, in which more than 50 mines were visited. Many of these were studied in detail; in all several thousand working places were examined, and readings taken relative to ventilation run into the tens of thousands.Object of ventilating metal mines:Whereas in coal mines ventilation is generally regarded as essential, in many metal mines, especially shallow ones, the operators pay little attention to ventilation, or ignore it altogether. Recent shortage of labor, and numerous accidents to which State compensation laws have directed attention, are causing metal-mine operators to regard ventilation more seriously, especially in deep, large mines.There is, in fact, greater necessity for adequate ventilation of metal mines than of coal mines. The latter require air currents to remove explosive gases and the fumes of explosives, but metal mines, in addition to the need of removing fumes of explosives, and occasionally explosive gases, frequently have need of removing dusts dangerous to health, reduction of high temperatures and high humidity, and removal of inert but unhealthful gases like CO2 and nitrugen. The generally accepted superior healthfulness of coal miners as compared with metal miners, is probably due in large part to the better air circulation in working places of coal mines.

Jun 1, 1920

By Andrew Allan

[Research conducted by the Bureau of Mines hrinq the last 5 years on the uce of machines for 7!naer:rolmrl ?.eve loym~nt in pi.t,c hlng anthracite beds l~a~ provide? data ?howin? that ?:;panrt of thc roof an9 str?eg of thes? oTen - jnqs requires almst half of' the PRS? workin? time. The possibilitie~ of i!rinz a mvable,. te1.ee*co@. c tpr? 3f ?tee1 ~h-!.oltl at the face in~tetcrl of conventional wood a*ti~yorts w?r? si:~q~eteil by engineers engaqad on the~ work If ~uch a shi~l8 COLI.~,~. be ~sve~.~yad, it tnillil man that face workera w~uld be provi8ed with mulrnu.m prot?ct+on from falls of' roof and ribs mi! the en- tire ehift could he I~W? Lo ~lro,J.~:ce cocl. Fermanent tim3er coald be p'l.acnA behind the shielR independently of the 'face work as the face advanced.]

Jan 1, 1953

By A. Visnapuu

The Bureau of Mines has upgraded high-iron domestic chromite concentrates by a carbonyl process. The upgraded chromite concentrates show as much as 10 wt pct higher Cr203 content and up to a threefold in-crease in the Cr:Fe ratio, compared with the starting concentrates. The high-iron chromites were first reduced to convert the iron oxides to the metal, and then treated with CO at elevated pressures and low temperatures to convert part of the metallic iron fraction to iron pentacarbonyl. Carbonylation was accelerated by the addition of H2S in small quantities. The iron pentacarbonyl was extricated from the con-centrate in the pressure reactor during carbonylation by a CO sweep through a pressure-reducing valve and passed through a decomposer at atmospheric pressure to convert it back to iron metal and CO. CO pres-sure, temperature, promoter trends, and other factors enhancing iron pentacarbonyl formation are presented.

Jan 1, 1985

The panic bars (and associated linkages and electrical circuitry) that are defined in this document are a machine operator-actuated control for the emergency deenergization of the tram motors on self-propelled, electric and diesel face equipment; including haulage equipment such as shuttle cars. There are nine basic types of panic bars (and several variations) that are recommended in this document, but all of the panic bars are characteristically of the "fire door" type that is frequently encountered on outside exit doors of many public and some commercial buildings. It is also the intent of the following panic bar designs that, when emergency brakes are added to the face equipment machinery for which they arc required, that they be designed and hooked up so that actuation of the panic bar will result in automatic application of the emergency brakes (immediately following the deenergization of the tram motors). The following panic bar design requirements are a restatement of the proposed requirements defined in the Federal Register, requirements cited in "Guidelines for the Design and Installation of Devices for Deenergization of Self-Propelled Electric Face Equipment/Automatic Emergency Brakes" by G. E . Lester and J. D. Greenhalgh of MESA, and Bendix recommendations that were formulated as a result of discussions with personnel at the various machine manufacturers and underground coal mines that we surveyed, discussions with G. L. Judy (our consultant), etc:

Jan 1, 1974

By Michael S. Miller

In 1987, 1988 and 1989, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the Sperry Creek Wilderness Study Area (OR-003-035; 5,600 acres) and the Gold Creek Wilderness Study Area (OR-003-033; 13,600 acres), plus an additional area (OR-003-033; 2,180 acres) adjacent to the Gold Creek Wilderness Study Area. The wilderness study areas and the addition are south of the Malheur River and are about 20 miles east of Juntura, Oregon. The wilderness study areas and the addition are underlain by volcanic rocks, predominantly basalt and rhyolite flows, breccias, and welded ash-flow tuffs. Lacustrine deposits containing diatomites occur mainly at the east side of the Gold Creek Wilderness Study Area and addition. Alluvium lies along the Malheur River, in terraces and fans south of the Malheur River, and along the floors of some creeks. Shear zones and faults have offset the rocks and provided channels for eruption of volcanic rocks and epithermal mineralization by hot springs.

Jan 1, 1989

By T. E. Gray

This report describes the preparation characteristics of the signifi¬cant coalbeds in Preston County, W. Va. It is one in a series of reports planned to determine coals suitable for the production of metallurgical coke, either as mined or after beneficiation. Over 2 million tons of coal was produced in Preston County, W. Va. in 190, none of which was cleaned mechanically. Estimates as of January 1, 1959, indicate that more than 3 billion tons of coal remained in the county in beds 12 inches or more thick. The Bakerstown, Mahoning, Upper Freeport, and Upper Kittanning beds were selected by the Bureau of Mines for study based on current production and estimated minable reserves. Sample locations were selected after study of the literature, conferences with mining engineers and mining company offi¬cials in the field, and examination of available sites. Four samples were collected from the Bakerstown and Upper Freeport beds and one each from the Mahoning and Upper Kittanning beds.

Jan 1, 1961

By G. M. Kintz

From 1895 to 1932, inclusive, 1,0163/ men were killed in and about New Mexico coal mines. Of these, 473 (approximately 47 percent) were killed in the 17 explosions listed in this paper. The second largest explosion of record in the United States, in so far as fatalities are concerned, occurred in New Mexico. The data in this circular were taken from publications of the United States Bureau of Mines and published annual reports of the State inspector of coal mines of New Mexico. The tables included are complete only with regard to major disasters. The Bureau of Mines considers as a major disaster one in which 5 or more men are killed. A few minor disasters are included, however.

Jan 1, 1934

By T. D. Moore

Methane emission from two surface gob-degasification boreholes was measured by the Bureau of Mines. The investigation took place during mining of a 3,200-foot longwall panel in the Lower Kittanning coalbed in central Pennsylvania. The first hole was 500 feet from the start of mining, and the second hole was 2,200 feet. The first hole went on natural draft as soon as the longwall face passed it. This caused the methane flow in the return entries to drop 75 pct. In the 6 months required to complete the panel, the two holes emitted 69 MMcf of methane in varying percentages of concentration in air. In 3 years, the holes emitted a total of 150 MMcf of methane.

Jan 1, 1976

By Robert J. Evans

The Hopper-Feeder-Bolter (HFB) is a prototype multifunctional machine designed to improve productivity by minimizing continuous miner place changes. It is designed primarily to work beside a two-pass continuous miner, bolting on one side and then place changing to bolt the other side while simultaneously providing a surge car and lump breaker located directly behind the continuous miner. Surface testing was conducted at the Bureau of Mines Mine Equipment Test Facility (METF) to evaluate overall system performance and reliability. Tests were conducted to evaluate place changing, tramming, lump breaking, roof bolting, drawbar pull, conveying, temporary roof-support (TRS) capacity, lighting, and noise. Surface test results indicate the HFB is ready to be tested and evaluated underground in a production mode.

Jan 1, 1988

By G. W. Birge, D. E. Wolfson, J. H. Lynch

Fourteen coal samples representing the Flag , Fire Clay , Whitesburg , Amburgy , Upper Elkhorn No. 3 , Upper Elkhorn No. 2 , Upper Elkhorn No. 1 , and Lower Elkhorn beds in Letcher County , Ky . , were carbonized by the Bureau of Mines - American Gas Association ( BM- AGA ) method , and yields of products and physical properties of cokes were determined . The samples tested were high- volatile A bituminous in rank , with dry , mineral - matter- free fixed - carbon contents ranging from 55.3 to 62.2 percent . Five of the samples , as received , were chemically unsuitable for metallurgical use because of excessive ash and/ or sulfur content . Generally , strength indexes of the cokes were low and all of the coals would require blending with higher rank coal to obtain satisfactory blast furnace fuel .

Jan 1, 1964

By G. L. Oldright, Virgil Miller

"This paper is the ninth 4 of a series on smelting in the lead blast furnace, and the fourth on modifications brought about by the introduction of richer charges.ACKNOWLEDGMENTSThe authors wish to express their appreciation to Stanley A. Easton, Frank M. Smith, and A. F. Beasley, and to their staff for the whole—hearted cooperation that made it possible to obtain the data in this publication at the Bunker Hill smelter, Kellogg, Idaho.INTRODUCTIONIn tie account written of the conditions obtaining at the tuyere zone in the blast furnaces at Tooele (R. I. 2965) the authors gave references to articles covering (1) the effect of temperature on the equilibrium 2C0 - CO2 + C, (2) experimental work that has been done on learning the gases existing at various elevations in columns of burning coke, (3) extension of this work to the tuyere zone of an iron blast furnace, and (4) the paper itself gave similar analyses of the gaseous oxides of carbon at the tuyere zone of a lead blast furnace and showed the temperatures obtaining there. There were also references in the above paper to the literature on (5) how the lead compounds likely to be present might be ex¬pected to react. A careful study of the original articles selected as references will give a good background for the present work.The following very brief recapitulation may be convenient before considering the tuyere zone in the blast furnaces at Kellogg. The ""producer gas reaction"" (1) of course goes to the left at increasingly higher rates of speed with increase of temperature. When air is blown upward through a grate and a column of hot fine coke alone, oxygen as such penetrates from some 2 to 3 inches only, under the conditions obtaining as to the amount of surface exposed per unit volume of air. When air is blown at about 20 pounds pressure through the tuyeres in the side of an iron blast furnace into a column of coarse coke (plus furnace charge) it may penetrate for 30 inches before the oxygen is entirely used, burning first largely to CO2. Within wide limits, the rate of feeding air into the furnace has practically little effect on the composition of the gases obtaining in the fuel bed of fine coke, this being true particularly of the gases leaving the bed. Some 10.5 inches above the grate the gases contained 22 per cent of CO by volume, and a little further up the CO2 had practically disappeared. This gave the familiar three zones in both the iron blast furnace and the gas producer; in order of entry of the air, in the first the oxygen burned largely to CO2, in the second the CO2 was reduced to CO, and the third the CO2 was practically absent. In the furnaces at Tooele, conditions were somewhat erratic but the first two zones were present, there being, however, no zone in which CO2 and 02 were both entirely absent."

Apr 1, 1931

By Robert C. Dyni

This U.S. Bureau of Mines (USBM) report summarizes a field demonstration of pneumatic backfilling technologies conducted at the abandoned Hillside Coal and Iron Slope in Vandling, P A. Researchers demonstrated two pneumatic backfilling technologies recently developed under the USBM's Abandoned Mine Reclamation Research Program, the Pneumatic Pipefeeder and the High-Efficiency Ejector. Both systems had previously been evaluated at the USBM's subsidence abatement investigation laboratory near Fairchance, P A. The objective of the demonstration was to fill 100% of the abandoned tunnel with backfill stone to prevent further subsidence. The Pneumatic Pipefeeder was used for 21 days, at a rate of 63 to 124 t/ d (69 to 136 st/d), to fill 88% of the tunnel. The High-Efficiency Ejector was used for 2 days, at a rate of 125 to 132 t/d (138 to 146 st/d) to fill the remaining 12% of the tunnel. The backfill placed by both systems was tightly compacted. The major problem encountered was wear on the polyethylene pipeline from the abrasion of the high-velocity backfill. The use of heavier steel pipe minimized the problem. A cost analysis for the entire project is given.

Jan 1, 2010

By R. H. Jefferson

An electrochemical method to selectively determine sulfur dioxide in the presence of sulfur trioxide was investigated. A hydrophobic gas-permeable membrane separates the gas sample solution from an internal filling solution containing a fixed quantity of chloride ion and a sufficiently large excess of sodium bisulfite so that its concentration may be considered constant. Sulfur dioxide diffuses through the membrane to dissolve in the internal filling solution and liberates an equivalent quantity of hydrogen ions. The electromotive force between a precision-ground, flat-ended pH electrode, which acts as the sensing element, and a chloride sensing electrode, which acts as the reference element, gives a direct measure of S02 in the gas sample solution. Calibration curves in water, tetrachloromercurate (TCM) , and citrate buffer absorption solutions were closely parallel with slopes in their linear segments, ranging from 57 to 52 mv/decade of S02 concentration. The slopes compare reasonably well with the theoretically expected slope of 58 millivolts at 21° C. The water standard curve was linear with respect to the logarithm of S02 concentration from 1 to 1,000 ppm S02; the TCM standard curve was linear from 10 to 2,000 ppm S02; and the citrate standard curve was linear from 30 to 5,000 ppm S02' The high efficiency and nontoxicity of citrate favor it as a substitute for the conventionally used TCM in the absorption solution.

Jan 1, 1976

By Floyd G. Anderson

The increasing trend toward use of continuous-type mining machines created a significant dust problem in coal mining, which resolved itself into three categories: Visibility at face, deposition on return airways, and the potential health hazard. The control measures applicable to these conditions and studied or developed from 1955 through 1957 are summarized and reviewed in this report. Other important problems brought into focus during the same period were radiation exposure in uranium mining and high temperature and humidity. Although temperature and atmospheric pressure alone may not be contributing factors in the incidence of silicosis, the few mining companies who operate under the extremes of these conditions are dust conscious and keep dust-control engineers on their operating staffs.

Jan 1, 1961

By F. S. Crawford

Safety devices and guards are often looked upon as the last word in safety by the men around the shop or large industrial plant . However , thorough knowledge of the details of their jobs and of the dangers attending them are even more important . It should be unnecessary for all men to go through the experience of the first man to meet an unknown danger , but that appears to be about the only way by which many learn . Practically every danger connected with the job around a mine , blast furnace , steel mill , foundry , coke oven , cement mill , or other operation , was encountered for the first time by someone , and if he was fairly fortunate he either got hurt or just missed being injured and lived to tell his " budaies " how it happened; he spread the knowledge of that particular danger . Sometimes , but not often , a man can foresee a danger . If he could always be on guard and remember everything he had ever learned and also know everything that had happened to the other fellow , and then let that knowledge keep him aware of the dangers in his own immediate " job , " so that he would work the safe way for both himself and the other fellow , he would have what safety engineers call " safety consciousness . " Being safety conscious is a fine attribute , as it really means knowing all about one's job . A man who is really safety conscious is one of the best and most efficient workmen in the whole plant . The boss wants men of that kindmen who want to learn and who try to learn every little detail about their jobwhere there is danger of spoiling the heat or getting burned by hot metal in a steel plant or of loading rock instead of coal or ore in a mine . Such men know how to do whatever job they are on easily and with the least amount of hard work and at the same time get it done as quickly as possible with safety . A man who is safety conscious has to nearly all intents and purposes developed eyes in the back of his head , if he is in a big mill where there if something going on all around him . These eyes are not real eyes , but they are what might be termed a sixth sense which he has developed by his experience in the mill as well as in other dangerous work which he may have done before in other plants . There may be occasions when a man's safety consciousness will leave him for just a short time ; this is likely to happen when he is thinking about a quarrel he had with his wife which has not been cleared up happily , or perhaps when he has bought too many things on installment and with sickness at home

Apr 1, 1931

By M. Clair Smith

The Sweetwater, Castro, Trinidad, New London, and Hilltop chromite properties are situated within an area 8 miles long and 1 mile wide between San Luis Obispo city and Morro Creek, San Luis Obiso County, Calif. Development work at this group of mines was a part of a long-range project by the Bureau of Mines to develop strategic mineral reserves in the United States in accordance with the Strategic Minerals Act of 1939. The junior author of this report participated in the preliminary examinations made in 1941 of the chromite deposits that later in the same year were the subject of more intensive investigation under the immediate supervision of the senior author. The ore occurs in lenses and kidneys in masses of dunite contained in large poridetite areas. Production has boon in the form of lump ore and concentrates from disseminated ore. Work by the Bureau of Miner included surveying, mapping, trenching, sampling, and assaying. It is summarized separately in the text under the name of each mine investigated. The report gives a brief history of the district, describer the concentrating plant of the Castro Associates, and gives detailed results on sampling and assays at the various proportion.

Jan 1, 1951

By H. -F. Krausse

Roof failures in underground coal mines are related to the lithology and geologic structure of the roof. There are two distinct suites of roof rock above the Herrin (No. 6) Coal in Illinois, and each has distinctive patterns of structure and roof failure. In black shale-limestone roof areas, roof instability is correlated with thinning of limestone beds and presence of faults and clay dikes. In gray shale roof regions, the prime roof hazards are posed by rolls, shear bodies, and presence of coal or carbonaceous partings in the roof. Most structural features examined are believed to have formed during early stages of sediment diagenesis and compaction. Structural trends and lithologic patterns are strongly interdependent for this reason. In many cases geologic patterns are so complex and locally variable that prediction of roof stability far in advance of mining is difficult. The need for greater flexibility in roof control planning is apparent.

Jan 1, 1979

By M. Shabbir

A study was made to determine the optimum conditions for precipitation of uranium from mill solutions using hydrogen peroxide. Precipitation tests were made on both synthetic and actual mill solutions. Parameters studied included amount of hydrogen peroxide, initial pH, reaction pH, time, and temperature. Also investigated was the effect of varied amounts of vanadium, molybdenum, and sulfate in the test solution on uranium precipitation and product quality. The optimum conditions for complete precipitation and high product quality were (1) the use of 150 percent of the stoichiometric requirement of hydrogen peroxide, (2) initial pH of 1.0, (3) reaction pH between 3.4 and 5.0, (4) 4 hours reaction time, and (5) ambient reaction temperature. The excess hydrogen peroxide requirement is partially dependent on the amount of impurities present in the feed solution. The hydrogen peroxide process appeared applicable to treatment of the several mill eluate and strip solutions tested. The experimental studies also indicated that the hydrogen peroxide technique gives substantially better product quality than that produced by ammonia precipitation.

Jan 1, 1974

By V. E. Edlund

Laboratory batch flotation tests were conducted on copper converter slags to evaluate the relative merits of recovering copper from slow-cooled versus water-quenched slags. Three slags containing 1.6, 5.0, and 6.6 percent copper were used. More than 90 percent of the copper was recovered in a rougher concentrate leaving a 0.2- to 0.3-percent copper tailings when treating slow-cooled slag. Lower recoveries and higher copper tailings ranging from 0.5 to 0.6 percent copper were obtained from quenched slag. Grindability studies were made on the respective heat-treated slags. Quenched slags proved more difficult to grind than slow-cooled slags. Cost studies showed that quenched slags can be treated at slightly lower cost than slow-cooled slags. However, the cost advantage of processing quenched slags is more than offset by the higher copper recoveries obtained from slow-cooled slags.

Jan 1, 1971