Search Documents

By C. A. Herbert

Coal-mine explosions in the United States during the past 10 years ranked third among the causes of coal-mine fatalities and constituted 16.1 percent of the total fatalities. In Indiana, however, during this same period the percentage of fatalities from this cause was much higher than the average percentage for the entire country. It is only through knowledge of the factors that have led to these past explosions that intelligent steps may be taken to prevent similar occurrences in the future. Although information concerning many of the earlier explosions is lacking, an attempt has been made to tabulate the information available in the hope that it may be of assistance in calling attention to some of the principal causes of explosions in Indiana.

Jan 1, 1934

By T. O. Glover

The Bureau of Mines surveyed unit trainloading and storage installations in the midwestern, eastern, and southeastern coalfields. Nine individual operations were studied in detail as a representative cross section of unit train operations in these areas. Of the nine operations studied, three were in Illinois, two in Kentucky, and one each in West Virginia, Tennessee, Ohio, and Pennsylvania. Information was obtained from coal producers, coal sale agencies, railroads, construction and equipment companies, and power companies.

Jan 1, 1970

By K. T. Menzies

This report documents laboratory and in-mine analyses of diesel exhaust pollutants carried out to assess the fate of potentially reactive species in the mine environment. Specifically, the concentration of stable compounds including carbon monoxide and carbon dioxide, and potentially reactive compounds including nitric oxide, nitrogen dioxide, sulfur dioxide, aldehydes, formaldehyde, acrolein, formic acid, odorants, particulates, soluble sulfates, and polynuclear aromatic hydrocarbons were determined. The concentration and mass emission rates of these compounds were measured in the laboratory under three engine speed and load conditions and with three exhaust control conditions, i.e., none, catalyst, water conditioner. Once calibrated, the engine was installed in the Bureau of Mines Safety Research Coal Mine and the concentration of exhaust pollutants measured at several distances downstream (inby) of the engine. Laboratory results confirm the relatively small effect of exhaust control devices on most pollutants under engine conditions of low speed and load. At higher engine speed and load, the catalyst is more effective in controlling many pollutants. The in-mine data indicates that during residence times, which are typical for miner/exhaust contact, most diesel exhaust pollutants do not decrease in concentration. The obvious exceptions are nitrogen dioxide, sulfur dioxide and formaldehyde. The concentration of these pollutants is reduced by up to 75 percent in five minutes. The lack of increase in levels of obvious reaction products indicates that surface loss may be a major sink for these pollutants.

Jan 1, 1980

By F. M. Goodwin, John Campbell, G. W. Jones

"INTRODUCTION The investigation of the general hazards of combustible gases and vapors in manholes owned by the Edison Electric Illuminating Co. and the study of methods for eliminating these hazards, conducted by the Bureau of Mines, the Edison Electric Illuminating Co. of Boston, and the Boston Consolidated Gas Co. since 1929, was continued during 1933.From May and through December 1933 these tests were supplemented by a study of the manholes of the New England Telephone & Telegraph Co. The test crew was under the direct supervision of John Campbell, superintendent of the Special Service Department of the Edison Electric Illuminating Co., and F. M. Goodwin, vice president of the Boston Consol¬idated Gas Co.The procedure of sampling manhole atmospheres and of shipping the samples to Pittsburgh was the same as that used heretofore. In previous reports the relative explosibility of the samples was calculated by adding the percentages of the illuminants, hydrogen, carbon monoxide, methane, and ethane, dividing the total by 6.5, and multiplying by 100. Experience has shown that the factor 6.0 is more nearly correct; therefore, this has been used in calculating the relative explosibility of all the samples listed in appendix A and B of this report. If gasoline vapor is present a smaller factor must be used.ACKNOWLEDGMENTSThe cooperative investigation was arranged through the interest and effort of W. C. Bayliss, president of the Edison Electric Illuminating Co. of Boston; W. C. Beckjord, vice president and general manager of the Boston Consolidated Gas Co., and A. C. Fieldner, chief engineer, Experiment Stations Division, United States Bureau of Mines. Thomas H. Haines, superintendent, Distribution Department of the Edison Electric Illuminating Co., cooperated heartily in furnishing both men and information for the work."

Oct 1, 1934

By E. E. Ungar

The ways in which noise is generated and radiated by chutes and screens are described and corresponding noise control concepts are discussed. The amounts of noise reduction produced by applicable noise control means are delineated and generally cost-effective means are recommended. Available noise control materials and their applications are discussed. The results of field measurements, laboratory experiments, theoretical analyses, and studies of data provided by suppliers are summarized.

Jan 1, 1975

By Dennis R. Kasper

This study evaluates selective environmental impacts of two distinct in situ mining techniques. In situ leaching of uranium, porphyry copper and native copper and in situ borehole (slurry) mining of uranium, sandstone, and pebble phosphate ores are the techniques and minerals investigated. The potential impacts onsite in the desert southwest (porphyry copper), Michigan (native copper), Texas and Wyoming (uranium), and Florida and North Carolina (phosphate) are addressed and discussed. The study emphasizes those impacts which are unique to in situ solution leaching and borehole slurry mining. Impacts which are characteristic of all construction projects in the general geographical areas investigated, such as socioeconomic effects on surrounding communities and site-specific impacts, such as rare and endangered species, are beyond the scope of this study. For each of the in situ processes and associated ores investigated, the physical and chemical characteristics of the systems are described, the toxicity of the leaching solutions are presented, and the potential impacts on the environment are developed.

Jan 1, 1979

By Walter Murphy

For a number of years the Bureau of Mines has been studying the properties of crude petroleums produced in the United States and the Western Hemisphere. A number of reports have been published giving the analyses of crudes from the different fields and regions as made by the Bureau of Mines Hempel method of analysis.4 Several of these reports include analyses of crude oils from the Rocky Mountain region.5/ The search for new fields and new producing horizons in old fields in the Rocky Mountain region has been quite intensive during the last few years, and a number of discoveries have been made.

Jan 1, 1937

By Harold H. Fukubayashi

The effect of various zinc electrowinning solution impurities on the surface morphology of deposited zinc was investigated. Impurities studied included Al, Ag, Cd, Co, Cr, Cu, Ge, Mn, Ni, Sb, Sn, Ti, Pb02, PbSO4, and HC1. Also, the effect of animal glue, gum arabic, and Na2SiO3 additives on the deposited zinc surface structure was studied. Results were compared with deposits from a pure electrolyte consisting of H2SO4 and Zn+2, 200 and 65 gpl, respectively. Zinc was deposited on a Al cathode, 99.9 pct pure, using Pt anodes. Time, temperature, current density, and impurity concentrations were con¬troller The bulk of the tests were conducted at 40° C and 75 A/ft2 (82 mA/cm2). A scanning electron microscope (SEM) was used to examine the surface morphology. X ray diffraction techniques were used to determine crystal orientation and nondispersive X-ray spectrometer analyses were employed in an attempt to locate impurity concentrations on the zinc deposit when pitting or re-solution occurred. The impurities were categorized by their effect on current efficiency, morphology, and apparent mechanism of H2 evolution from the cathode.

Jan 1, 1974

Low-cost housing, like automobiles, should be appraised in the light not merely of first cost but of upkeep as well. Even more important than the number of miles the family car will go on a gallon of gasoline is the number of days the family home can be kept comfortable on a ton of fuel. A furnace tender who tossed every third shovelful of coal into the ashcan would lose his job promptly, but the effect is the same when homes continue year after year to pour out precious heat through uninsulated roofs and walls, Greater economy in household heating means even more to the national economy than to the individual, especially now that we are preparing for defense. Our fuel resources, although large, should be conserved. If less fuel is used for civilian needs, augmented requirements for defense can be met without unduly increasing the number of men needed at the coal mines and oil ells or adding new producing units that might complicate ultimate readjustment to peacetime conditions when the emergency is past and over-expansion of many industries brings new problems if unnecessary demands for transportation facilities are reduced, public carriers will be able to haul more munitions, and manpower needed for national defense will be released; and by protecting workers from health hazards in their homes additional man-hours of productive effort will be gained. Moreover, reducing the running expenses of houses by proper heat insulation helps home owners to maintain payments on property, and by minimizing foreclosures helps to stabilize the financial structure of the country. In short, here is a situation where the interests of the individual and the Nation are identical and the greatest good for the greatest number is obtained without sacrifice to anyone.

Jan 1, 1941

By James J. Dowd

The investigation to evaluate the reserves of coking coal in the United States suitable for the manufacture of metallurgical coke is being made by the Bureau of Mines in three parts: (1) To estimate known (measured plus indicated) recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and (3) to study the carbonizing properties of coals and coal blends not now widely used for metallurgical coke making. This is the fifth of a series of reports giving the results of studies by countless under part (1) of the investigation. (See appendix.) This report covers Westmoreland County, Pa., which comprises parts of New Kensington, Freeport, Elders Ridge, Pittsburgh, Greensburg, Latrobe, New Florence, Johnstown, Brownsville, Connellsville, Donegal, and Somerset quadrangles. (See fig. 1.) A short resume" of the chemical and carbonizing properties of the coals are included. Data on the coal beds in this county were obtained from mining companies, land companies, individual landowners, and other sources of authentic information. A base map for each bed in each quadrangle was made to the scale 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds up to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick. These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas, areas excluded from the estimate, and areas outside of the outcrop were measured by planimeter on the base maps. Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1951

By A. G. Loomis

Although secondary-recovery methods have not been applied widely in California, it is apparent that increasing attention and effort must be given to this phase of recovery if the State is to maintain its high rank as a petroleum producer. Steadily increasing demands for petroleum products and decreasing rates of discovery of new oil fields, with rapid depletion of existing reserves, emphasize the prospect of an adverse situation of supply and demand in the not-far-distant future. If the trend of discoveries becomes more favorable or if more complete economic recovery of the oil in place can be obtained by secondary recovery, this situation can be averted. Not only are these reserves of economic importance to the petroleum industry for meeting increasing market demands; but economic reclamation of such reserves is an important conservation measure, which will prolong the productive life of many fields. Accordingly, progressive operators in California are alert to the possibilities of secondary recovery and have done much to implement such operations wherever feasible. Most current operations are of the pressure-maintenance type, in which the reservoir pressure is maintained or partly maintained by injecting natural gas to in-crease oil recovery. The possibilities of recovering additional oil from stripper fields by gas drive and water flooding (including water disposal) also are being tested in experimental field projects. Table 1 summarizes current gas-and water-injection projects in California.

Jan 1, 1952

By R. S. Fowkes

The degree and manner of packing of bulk materials influences all phases of their loading, such as by a front end loader or a dragline, and their mechanics of flow, such as through a binhopper or an ore pass. The most important quantity in analyzing the handling of a bulk material is its shear strength which depends primarily on the same parameters as those that determine the packing state. Some of these are size, size distribution, moisture content, particle shape, particle orientation, and cohesion. The variables that affect the packing state arc vibration, pressure, intensity of deposition, velocity of deposition, and, when the material is confined, container used. The analysis of packing by a number of investigators has been done almost entirely with spherical particles. Most of these studies have dealt with monosized spheres. There is scant information on particles with angular shapes. Since most of the investigations by far have been concerned with ceramics and powder metallurgy, the particle sizes and ranges of size distribution have been small compared to those generally found in mining after fragmentation.

Jan 1, 1974

By Paul M. Tyler

Calcium chloride is a conspicuous example of a former waste product that has found a place for itself in the onward march of civilization. Formerly considered a troublesome constituent of the effluent sewage of many chemical manufacturing plants and salt works, it has now become a commercial product of substantial importance, with sales aggregating almost six million dollars in 1929. The point has not yet been reached where it would seem profitable to undertake large-scale production of calcium chloride as a main product, but as a byproduct it has become an item that warrants serious consideration by all who are in a position to recover it at sufficiently low cost. The largely increased demand for bromine and for certain magnesium salts, which are likewise potential byproducts associated with calcium chloride in most salt-works bitterns (and brines generally), adds further impetus to commercial research directed toward the fuller utilization of the natural saline resources of the United States.

Jan 1, 1934

By J. L. Reuss

The Bureau of Mines investigated the technical feasibility of smelting copper concentrates containing chalcocite (Cu2S) and native copper using nonpyritic sulfur-bearing materials to aid matte formation. The procedure consisted of combining various proportions of commercial chalcocite concentrate, smelter slag, fluxes, and matte-forming constituents to produce charges of comparable compositions. The mixtures were charged in fire-clay crucibles and smelted in an induction furnace at 1,300° C. The research proved that either sulfur or gypsum can replace pyrite as a matte-forming material, and that gypsum produces an exceptionally high-grade copper matte. The addition of small quantities of metallic iron to the nonpyritic smelting charge furthers the removal of sulfur, improves the recovery of copper, and makes it possible to utilize gypsum as the exclusive flux and matte-forming ingredient, thereby eliminating the necessity of adding limestone.

Jan 1, 1968

In March, the Minister of Mines, Mrs. Judy Erola, released a mineral discussion paper at the annual meeting and convention in Toronto of the Prospectors and Developers Association. Among the mineral objectives discussed was the revitalization of the "junior" mining industry. That industry reportedly has seen its share of total exploration expenditures fall from 50% in 1969 to 10% in 1979. Some sources believe the reason to be the rise of exploration costs and more- restrictive legislation The junior mining industry reportedly was responsible for 40% of all mineral discoveries in the 1969-79 period. CZECHOSLOVAKIA Czechoslovakia expects its capacity for the recovery of gallium metal to increase from 1,650 kilograms to nearly 3,000 kilograms per year by the installation of new recovery equipment at the aluminum plant at Ziar Nad Hronom in Central Slovakia. World production data are not reported, but the United States consumed 8,000 kilograms (estimated) in 1981, of which 5,536 kilograms were imported. Gallium is recovered as a byproduct of the Bayer process for the conversion of bauxite to alumina, and from certain zinc processing wastes. It is used for electronic applications such as light-emitting diodes for visual display panels in calculators, clocks, and other instruments.

Jan 1, 1982

By J. P. Morris

A diphenyl ether calorimeter for measuring high-temperature heat contents of ferrous alloys and iron-and steelmaking slags was constructed and calibrated with specimens of molybdenum, alumina, and platinum that were heated to temperatures ranging from 1,720° to 1,875° K. The standard deviation of the calibration measurements was 0.37 percent. By measurements of the enthalpy of delta and liquid iron, the heat of fusion of iron was found to be 3,298 ±100 cal per mole.

Jan 1, 1966

By D. R. Tesarik

As part of its research program to investigate ways of improving resource recovery and reducing subsidence, researchers from the U.S. Bureau of Mines placed instruments in the B-North ore body of the Cannon Mine, Wenatchee, WA, to monitor cemented backfill and rock deformation during mining. The vibrating-wire gauges proved to be reliable and versatile, and approximately half of the instruments are providing data after 2 years of use. A two-dimensional, finite-element model was used to analyze the Cannon Mine's multilevel bench cut-and-fill mining method and predict rock and backfill displacements. The model accurately predicted rock displacements, but the predicted and measured displacements in cemented backfill had a correlation coefficient near zero, indicating that the model should only be used to predict rock displacements and not backfill displacements. A finite-difference model was also used to evaluate the stability of a cemented backfill pillar. Results can be used to conservatively predict backfill stresses, but on-site observation of pillar failures coupled with in situ measurements are needed to make more accurate predictions. An ongoing evaluation of the mining system has indicated that filling the primary stopes tight to the back with cemented backfill allowed these pillars to carry overburden loads soon after the cemented backfill was placed.

Jan 1, 2010

By Raymond W. Hiteshue, Sam Friedman, Martin D. Schlesinger

The Bureau of Mines in cooperation with the El Paso Natural Gas Co. investigated the effect of high temperature and pressure at short residence times on the hydrogenation of a New Mexico coal to gaseous and liquid hydrocarbons . The study was made in a bench - scale semicontinuous unit at pressures of 500 to 6,000 psig , 480 ° to 1,000 ° C , and residence times of less than 1 minute to 15 minutes . Ammonium heptamolybdate was impregnated on the coal to furnish 1 percent molybdenum based on maf coal . Coal could be rapidly hydrogenated at elevated temperatures and pressures to yield large quantities of gaseous hydrocarbons and small quantities of lowboiling oils , high in single - ring aromatics . At 800 ° C and 6,000 psig and a residence time of 1 minute , the yield of hydrocarbon gas was 43 percent and of liquid hydrocarbons 9 percent , based on maf coal . With a 15 - minute residence time , the yield of gaseous hydrocarbons increased to 68 percent with a decrease in yield of oil to 6 percent . At higher hydrogen velocities , the yields of oil were much greater but contained large quantities of asphaltene . Low concentrations of molybdenum (0.01 and 0.1 percent ) or a high concentration of iron ( 1 percent ) were ineffective at 800 ° C , 6,000 psig , and short residence time .

Jan 1, 1964

By Walter Wood, J. T. H. Cannarella, H. F. Yancey, R. E. Zane

More than 50,000,000 tons of bituminous coal and probably about the same quantity of anthracite are cleaned annually in the United States by wet methods. The water, fine coal, and impurities from the water used for washing ordinarily are recovered by moans of various forms of settling tanks. Settling and clarification may be hastened markedly, thereby greatly increasing the capacity of clarification equipment already installed, by the addition of substances to the washery water that cause the fine particles in suspension to agglomerate and thus settle more rapidly. This phenomenon, although well known and applied in other fields, has been used at only a few coal washeries in the United States. It is widely employed, however, as an aid in the recovery or disposal of fine coal or impurities, as a means of preventing, stream pollution, and to enable reuse of washery water at many plants in Europe. Pioneering work in the United States has been done principally by two companies -- the Pittsburgh Coal Co., in Pennsylvania, 6/ and the Pacific Coast Coal Co., in Washington.

Feb 1, 1940

By R. L. Bolmer

Rapid depletion of our known mineral resources has stimulated exploration for new mineral deposit. Abandoned mines or prospects may prove to be commercial in today's economy. Often it is necessary to revaluate such properties. Some of these may be inaccessible because of caving of flooding. Many, however, remain in good condition, except that over the years the air in the workings has become depleted of oxygen. Each year the Bureau of Mines receives numerous requests for aid in entering old mines, the air in which is incapable of supporting life. Requests of many individuals who wish to examine or explore-such places with the help, of the Bureau's self-contained oxygen breathing apparatus have been denied because of the hazards involved in the use of this equipment for such purposes. The distance to be traveled in irrespirable gases may be too great for safety; under favorable conditions, a round trip of 2,000 feet from fresh air is the maximum distance that may be traveled.3/ The use of such equipment is hazardous unless a team of at least 5 men thoroughly experienced in its use is provided; and when extensive traveling from. a fresh-air base is required, a reserve team should be provided.3/ Usually, the apparatus is requested for use in exploring workings having only one surface connection, as mines having more than one opening usually are more easily ventilated;,and in some natural ventilation is sufficient or can be made so by cleaning out obstructed openings.

Jan 1, 1951