Search Documents

By L. C. IlsLey

The theory and practice followed by the Bureau of Mines in investigating electrical equipment4/ made for service in gassy mines are of particular interest not only to manufacturers but also to those organizations that deal with safety anal inspection at the mines. This publication purposes to discuss the theory upon which tests of equipment in explosive atmospheres are based and to consider inspection and other matters pertaining to investigations made by the Bureau in ascertaining whether a machine merits approval. The material in this report is taken from an earlier bulletin,5/ which is row out of print, and has been revised and brought up to date to make the information again available to manufacturers, inspectors, and others interested in the development of safe equipment.

Jan 1, 1954

By John E. Hamak

The identified helium resources of the United States were estimated by the U.S. Bureau of Mines at 617 Bcf, as of December 31, 1992. This includes 285 Bef of demonstrated reserves, 85 Bcf of demonstrated marginal reserves, and 37 Bcf of demonstrated sub-economic resources. The identified resources also include 166 Bcf of helium in inferred reserves and inferred marginal reserves and 44 Bcf in inferred sub-economic resources. The identified helium resources contained on Federal lands are approximately 172 Bcf, including 32 Bcf in underground storage in the Cliffside Gasfield near Amarillo, TX. Undiscovered helium resources in the United States are estimated at a most likely volume of 104 Bef, with a maximum volume of 249 Bcf and a minimum volume of 41 Bef. Also reported are 51 Bcf of helium in nonconventional and low-helium-content natural gases. Extraction of helium in the United States occurs mostly from natural gases produced from the Hugoton gas area in Kansas, Oklahoma, and Texas, and the Riley Ridge area in southwest Wyoming. Helium extracted from natural gas in the United States in 1992 was 3.3 Bcf. Some shortfalls in helium supply may occur in about 5 to 10 years.

Jan 1, 1995

By D. Randolph Berry

The objective of this program was to develop a system to extinguish coal mine fires by remote sealing of the underground passageways. The system developed had to be versatile enough to function under a wide range of operating conditions, including large variations in passageway geometry, depth of mine, water conditions, both in the mine and at the surface, and rubble in the mine passage. The system developed had to include instrumentation for the remote probing of the passageway prior to sealing, a system for sealing the mine passages, and instrumentation for remote monitoring of the quality of the seal during and after construction. These objectives were successfully achieved during this program. The remote mine sealing capability of the system was satisfactorily demonstrated in a field test conducted at the Eastern Associated Coal Corporation Federal No, 1 Mine in Grant Town, West Virginia.

Jan 1, 1973

By R. B. Tippin

The heavy liquid separation (HLS) process was investigated by the Bureau of Mines to develop a means of concentrating minerals from natural ores, Various spodumene ores were tested in a 0.4-inch diameter cyclone using pure tetrabromoethane (TBE) as the heavy liquid. Studies were initiated to examine the influence of (1) pulp density (2) feed grade, (3) cyclone pressure, (4) cyclone apex opening size) (5) cyclone vortex finder opening sand (6) mineral particle size on the separation efficiency. Each of these factors was found to affect the heavy liquid separation in some degree; the mineral particle size exhibited the greatest effect and the ore feed grade the least. Conditions necessary to yield an 85 percent spodumene concentrate with an 85 percent recovery were determined to be: 70 psig pressure, 10 percent solids, 0.08-inch apex opening, 0.11-inch vortex finder opening and a minimum amount of minus 200-mesh fines in the feed. Operation of multiple cyclones in series resulted in spodumene concentrates assaying over 90 percent and indicated mineral recoveries exceed-in 90 percent.

Jan 1, 1967

By H. M. Smith

The production of oil during the early development of new oil fields is usually accompanied by large quantities of natural gas. Since in most fields gas under pressure is the main source of the energy causing the oil to move through the sands into the wells and thence to the surface, coincident production of natural gas will continue as long as present-day producing methods are used. Generally the use of this gas is restricted, since markets are not readily available. Consequently, a large portion of the gas produced is often wasted by being blown into the air. The magnitude of gas waste is well brought out in the following statement by Miller: Only a few outstanding examples need be cited to show the enormous production of gas that accompanies the discovery of new sources. In April, 1927, the Ventura field produced approximately 210,000,000 cubic feet of gas a day; and during the summer of 1927 Alamitos Heights reached a peak gas production of 102,000,000 cubic feet a day; on December 1, 1928, as a result of the summer's deeper drilling in the Long Beach field, surplus gas production amounted to 125,000,000 cubic feet a day. It is estimated that in January, 1929, the Santa Fe Springs field will have a daily gas production of 387,000,000 cubic feet from the recently discovered Buckbee oil zone. Of this amount 274,000,000 cubic feet a day will be the surplus above the amount required for field and plant fuel, taken out by utility corporations, and that used in repressuring the Meyer sand which lies above the Buckbee zone. Another example of the waste of large volumes of gas is in the Turner Valley field of Canada, 6 where 250,000,000 cubic feet of gas is being burned daily in flambeaus, as there is no present outlet except at prohibitive cost.

Jan 1, 1931

By William E. Eckard

Production of oil from a narrow shoestring sand presents problems unique in the oil industry. Especially important, from both an engineering end an economic standpoint, are the limitations imposed upon well patterns and spacings by the shape of the field. This report concerns a study of the Paola shoestring, Miami and Franklin Counties, Kane., where well density of 0.85 acre per well was not uncommon to insure profitable primary recovery in a reasonable time. However, such a great number of wells increased the operator's investment and reduced his profit considerably. It was the purpose of this study to investigate various well patterns and spacings applicable to water-flooding a shoestring reservoir and the effect of these factors upon recovery of oil and the most profitable operation of the pool. The designer of well patterns for a shoestring sand should evaluate carefully the edges of the shoestring, even though they may be considered too thin to drill. These comparatively thin edges contain large quantities of recoverable oil; moreover they are resaturated with oil as the pool is water-flooded.

Jan 1, 1951

By L. D. Tracy

"IntroductionOne of the problems which the coal-mining industry must solve in the next few years is the redaction of its ever-increasing timber bill. This includes pit posts, mine tees, timber sets, and brattice boards. As an example of this increase, the following table of timber prices from the records of a coal company in western Pennsylvania, in a district where the supply of most of the different kinds of timber used can be shipped from points within the State, is self-explanatory: Present conditions seem to indicate the continued upward trend ox the cost of mine timber, although the regrettable calamity that has visited the chestnut timber in Pennsylvania may temporarily hold the price of some types of mine timber on a level basis. On account of the chestnut blight, many farmers will undoubtedly begin to convert their chestnut trees into timber before they become a total loss. This may provide, for the time being, a sufficient supply of mine timber to check the steadily rising prices.The local lumber producers are turning their attention to the production of the larger sizes of timber and lumber on account of an unfavorable price on mine ties. From the foregoing table, it is seen that the average advance in the price of ties during the period 1914 to 1920 is 52 per cent, while timber sets and mine car plank increased in value 60 per cent. Amore striking illustration is the fact that a 6 by 8 inch by 6 foot tie sells for 42 cents or at the rate of $17.50 per 1000 board feet; yet mine car plank and timber sets have a value of $48 per 1000 feet, an advantage of $30.50 in favor of the heavier timber.The supply of coal in Western and Central Pennsylvania will last for a long period and it is for the possible future demand for timber that the coal companies must provide. While steel, concrete, and other materials may, in many cases, prove an acceptable substitute, there is no doubt that timber will always be in demand."

Nov 1, 1926

By R. W. Dougherty

From time to time interest has been evidenced in transporting coal with water in pipe lines. About the year 1895, United States patents broadly covering a method of pumping coal with water through pipelines were granted to W. C. Andrews. His process was used to some extent in pumping anthracite culm and waste back into the worked-out portions of the mines. About 1905, W. T. Donnely was granted patents relating to pumping anthracite silt away from the breakers. From about 1913 until 1924, a British engineer, Gilbert G. Bell, used a short pipeline to convey coal with water from barges on the Thames River to the Hammersmith Electricity Generating Station, London. Minus 5-inch coal was transferred 660 yards through an 8-inch pipe. Some trouble was experienced with fine coal, which tended to plug the line. Bell made several proposals to transport coal by pipeline overland from the Midlands to London, a distance of about 100 miles, but these were never adopted. This survey is concerned mainly with the problems presented by actual pipeline transportation of coal with water. It is assumed that the coal will have been processed to remove most of the abrasive impurities by conventional methods prior to introduction into the line, and that it has been crushed to the required top size. Dewatering at the discharge end of the line is considered part of the conventional cleaning process. There still remain many pump-performance and behavior of water-coal mixture problems that can be solved only by actual performance tests. It is recognized that the distribution of coal to other than very large users is not changed. Large storage areas would be required to supply seasonal markets. Large users, such as power plants and heavy industries, could be supplied by branch lines directly to the point of use, It is also recognized that pipe lines might not be able to carry a full range of sized coal to meet market demands in many areas.

Jan 1, 1951

The Government of New South Wales has granted approval for Hunter Valley Aluminium Pty., Ltd" and Alcan Australia Ltd. to proceed with the building of an aluminum smelter at Lochinvar and the expansion of a smelter at Kurri Kurri. Construction of the smelters is expected to start as soon as the consortium is finalized in early 1982. The smelters are part of a plan to increase Australia's aluminum capacity fivefold to 1.5 million tons by the mid-1980's. CHILE Construction of a $61 million lithium carbonate plant in northern Chile will be started in early 1983 by Sociedad Chilena del Litio Ltdao Production is scheduled to begin in 1984 with an initial capacity of 6,350 tons of lithium carbonate produced from a brine deposit. The firm is owned 55% by Foote Mineral Company, of Exton, Pennsylvania, and 45% by Corporacion de Fomento de la Produccion-CORFO.

Jan 1, 1982

By E. A. Clarke

The vapor-phase section of the Coal Hydrogenation Demonstration Plant at Louisiana, Mo., was operated for the first time in April 1949. The run lasted only 10 days because of time limitation (pending plant dedication in May) and the small amount of charging stock available. The primary purpose of the operation was to break in and determine the operability of the equipment and to supplement the operators' classroom training with actual practice by operating the plant under mild conditions. A secondary aim was to obtain data on the hydrogenation of petroleum oil and lignite tar distillate at approximately 10,000 p.s.i. while making gasoline and Diesel fuel oil. Although the operations were carried out under conditions considerably below those used in the plant design, a great deal of experience and data was obtained. As it is not feasible at this time to conduct further vapor-phase operations on similar stocks, this report has been prepared to present and summarize the data obtained through this operation.

Jan 1, 1950

By R. F. Waters

Laboratory-scale selective volatilization methods developed by the Bureau of Mines to recover germanium and gallium concentrates from coal fly ash and phosphorus furnace flue dust are summarized. In the better experiments between 85 and 98 percent of the germanium was recovered as the lower oxide and as sulfides, and between 75 and 97 percent of the gallium was recovered as the lower oxide and as the trichloride. Grades of the condensates were inconsistent and varied between a few tenths of a percent and 8 percent, depending on the method used. In the primary extractions of germanium alone the degree of enrichment surpassed 100 to 1, and for gallium the best ratio was 30 to 1. Upgrading of condensates by vaporization retreatment and by leaching and precipitation is discussed. An appreciable degree of mechanical preconcentration by attrition scrubbing and elutriation was possible on two fly ash samples.

Jan 1, 1967

By Ludwig Schmidt

"IntroductionThe evaporation losses of gasoline in the refinery, can be reduced by proper methods of refinery construction and operation. When gasoline evaporates slowly, as when stored in tanks that are not vapor tight, the most volatile part evaporates first, so that the remaining liquid in not only less in volume, but is also lower in quality. In some,evaporation changes the characteristics of the product so much that it must be reblended to meet trade specifications.Refiners are, therefore, greatly interested in the various appliances and methods used to reduce these losses. In the past this interest has been directed largely to storage tanks, probably because evaporation from tanks is more readily observed than losses during other refinery operations. As tests by the Bureau of Mines on evaporation of gasoline from small storage tanks had indicated that the losses during the various stages of refining might be equal to or greater than those of standing storage, a survey was during the spring and early summer months of 1924 in a large number of refineries in the Mid-Continent field. In order to enable the refiner to select the results of those tests that conform most nearly to the conditions that he has to meet, tests were conducted at various stages of refining, as follows: (1) Randown tanks, (2) (agitators), (3) filling tank cars, (4) storage of refined products, and (3) miscellaneous handling. The results are presented in this paper."

Nov 1, 1925

By Jack Wright

The analysis of water produced with crude petroleum has interested oil producers since inception of the industry. Records of the first analysis of mineralized water produced from an oil-productive formation are obscure, and references to the first use of brine analyses to assist in solving problems of petroleum production are not available in the technical literature. However, many early reports of the Federal Bureau of Mines5-8 and Federal Geological Survey,9-11/ as well as articles in engineer and geological journals12-14/ placed special emphasis on the importance, interpretation, and application of water analyses. One of the earliest applications of water analyses, and still a major one today, is for identification of intrusive waters in oil wells. This may be done by comparing the chemical constituents of a sample of water indigenous to the oil-productive formation with those of samples from upper, water-bearing formations within the same general area. Some earlier investigators recognized the need for Analyzing samples of all waters encountered in drilling operations. Ambrose15/ stated, in part, "In wells being drilled, the engineer should grasp every opportunity to get a true sample of water from each sand. . .," and, "The waters of each oil field are chemically different from those of another field." The validity of the latter observation and the importance of the former one have been borne out by comparing the results of analyses of many samples and noting the differences in relative concentrations of like constituents of waters from the a geological formation in different localities or oil pools.

Jan 1, 1957

By James S. Browning

[The objective of this project wan to determine the technical feasibility of recovering the associated copper, lead, and zinc from the pyrrhotite axe, of the Great Gossan lead, which has bon pined only for it:, sulfur and iron contents so far. The report constituted a description and discussion of small-scale Preliminary studies. This great pyrrhotite or body has strategic value, inasmuch it contains considerable quantities of zinc, copper, and lead, as well as the iron rend sulfur. The recovery of the: copper, lead, and zinc, associated with certain of the pyrrhotite ore bodies, could augment our domestic supply of these metals.]

Jan 1, 1953

By D. Bienstock

Using a nitrided fused-iron catalyst, the Bureau of Mines investigated the Fischer-Tropsch reaction in the oil-circulation process. The nitrided iron was quite stable and permitted the longest run obtained thus far in the oil-circulation process without the need for reactivating the catalyst--3,700 hours of operation. The effects of several operating variables--temperature, pressure, gas-recycle ratio, space velocity, synthesis-gas composition, and synthesis with and without reflux of oil to the reactor--on the production of oxygenates were studied. The importance of removing reflux oil and of high gas recycle in increasing the oxygenate content was shown. A finished gasoline containing 28 percent by weight alcohols was produced. The research octane number (RON) was 92.9 clear, increasing to 98.5 with the addition of one milliliter of tetraethyl lead (TEL). INTRODUCTION The Federal Bureau of Mines has been engaged since 1944 in a research and development program on the synthesis of gasoline from coal. Gasification of coal with steam and oxygen to yield a "synthesis gas"--a mixture of carbon monoxide and hydrogen--is being investigated at Morgantown, W. Va., and the synthesis of gasoline by catalytically reacting carbon monoxide and hydrogen over iron by the Fischer-Tropsch reaction is being investigated at Bruceton, Pa.

Jan 1, 1960

By P. L. Swanson, A. T. Iannacchione, W. J. Gale

This paper outlines the concepts used to correlate rock failure with microseismic events and presents examples of microseismic monitoring together with associated computer modelling of the rock failure. This study is motivated by the need to develop improved ways to reduce ground control hazards in underground mining. Toward this end we present and compare results from numerical modelling and micro- seismic monitoring studies conducted at several different mine sites. Emphasis is on integrating results obtained with these tools to characterize, and thus increase our understanding of, important mine deformation processes. The ultimate goal is to use this knowledge to design mine structures, and develop mitigation measures, that minimize specific ground control hazards.

By C. Q. Cupps

n view of increased interest in secondary recovery of oil in the Cut Bank field, Montana, a review has been made of unpublished data obtained during a 1943-44 study of reservoir oil characteristics in this field. Considerable uncertainty was attached to interpretations of subsurface oil sample analyses from six Cut Bank zone wells, one Lander sand well, and one Moulton sand well, because of adverse sampling conditions and wide range in the data. Much of this uncertainty has been removed by this review which has shown two of the Cut Bank zone samples and the Moulton sand sample to be representative of the reservoir oils. Estimates of original reservoir oil characteristics derived from differential-liberation analyses of these samples show that the oil in the Cut Bank zone was initially saturated at the gas-oil contact pres-sure, 750 psia, and the oil in the Moulton sand was undersaturated with a saturation pressure of only 380 psia. The rest of the samples were indicated to be nonrepresentative of the reservoir oils because of a disproportional vaporization of heavier components of the solution gas. The vaporization of these components is believed to be a cumulative effect of contact of the oil with bypassing, light-gravity gas which had been liberated at higher pressures from solution in oil farther back in the formation, or which had come from the gas cap, rather than from the singular effect of gas evolution caused by excessively low bottom-hole pressures. Change of oil composition caused by the latter was found to conform closely to that occurring during a differential liberation of gas in the laboratory.

Jan 1, 1967

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

C THRM 1 C CALCULATION OF MINE HEAD LOSSES FROM ALTIMETER SURVEY DATA TURN 2 C PENNSYLVANIA STATE UNIVERSITY - MINERAL ENGINEERING DEPARTMENT THRM 3 C THRM 4 C THRM 5 C THIS PROGRAM CALCULATES PRESSURE LOSSES USING THERMODYNAMIC RELATION- THRM 6 C SHIPS BASED ON POLYTROPIC FLOW BETWEEN STATIONS. FOR REFERENCE SEE THRM 7 C "A NEW TREATMENT OF MINE BAROMETER SURVEYS" BY M. J. MCPHERSON IN THRM 8 C 'THE MINING ENGINEER' NO. 109, VOL. 129, P 23. THRM 9 C THRM 10 C THRM 11 C THRM 12 C IDENTIFICATION OF ARRAYS THRM 13 C NOTE THE PROGRAM HAS BEEN DIMENTIONED FOR FOURTY (40) DATA POINTS THRM 14 C BASEC(6;2) BASE INSTRUMENT TEMPERATURE CORRECTIONS THRM 15 C TRAVC(6,2) TRAVERSE INSTRUMENT TEMPERATURE CORRECTIONS THRM 16 C BASER(I) BASE INSTRUMENT READING THRM 17 C TRAVR(I) TRAVERSE INSTRUMENT READING THRM 18 C TDRY(I) DRY BULB TEMPERATURE AT TRAVERSE STATION THRM 19 C TWET(I) WET BULB TEMPERATURE AT TRAVERSE STATION THRM 20 C ELEV(I) ELEVATION AT TRAVERSE STATION THRM 21 C VEL(I) AIR VELOCITY AT TRAVERSE STATION THRM 22 C TBDRY(I) DRY BULD TEMPERATURE AT BASE STATION THRM 23 C BASC(I) BASE READING CORRECTED FOR INSTRUMENT TEMPERATURE THRM 24 C TRAV(I) TRAVERSE READING CORRECTED FOR INSTRUMENT TEMPERATURE THRM 25 C BBASE(I) TEMPERATURE CORRECTED BASE READING IN BAROMETRIC THRM 26 C PRESSURE THRM 27 C BTRAV(I) TEMPERATURE CORRECTED TRAVERSE READING IN BAROMETRIC THRM 28 C PRESSURE THRM 29 C BTRAVS(I) BAROMETRIC TRAVERSE READING CORRECTED FOR ATMOSPHERIC THRM 30 C CHANGES THRM 31 C RELHUM(I) RELATIVE HUMIDITY THRM 32 C ASW(I) AIR SPECIFIC WEIGHT TURN 33 C R(I) GAS CONSTANT FOR MOIST AIR THRM 34 C STPRES(I) STATIC PRESSURE CHANCE BETWEEN STATIONS (I) AND (1-1) THRM 35 C TOPRES(I) TOTAL PRESSURE CHANCE BETWEEN STATIONS (I) AND (I-1) TURN 36

Jan 1, 1977

A symposium on the health hazards of respirable dust in the mining and milling of talc was held on May 8, 1973, in Washington, D.C. The results of medical effects on both human and animal subjects were presented. Methods for identification and classification of talc minerals were also presented. Analytical techniques discussed included X-ray diffraction, scanning electron microscope observation, electron probe, and optical microscopy.

Jan 1, 1974

This section of Minerals and Materials analyzes the following three factors affecting the recent performance of the U.S. and world mineral industries: 1) the health of the U.S. and world economies, 2) the level of interest rates and 3) the performance of productivity in both the U.S. mineral industry and the general economy. While these indicators do not exhaust the possible critical factors, they represent an initial attempt to probe some of the considerations underlying the performance of the U.S. minerals and materials industry. The U.S. and World Economies It is essential to analyze the state of the U.S. and world economy because the demand for minerals and materials is a derived demand; that is, since minerals and materials are used in the productive process, the demand for them is a direct function of the demand for the finished products of which they are a basic input. Thus, the demand for minerals and materials is directly affected by changes in present and planned consumption and investment expenditures. The past two issues of this publication have highlighted the generally discouraging performance of the national and inter-national economies. Briefly, the world economy is in the third year of the first long recession in recent history where inflation rates have remained above 5 percent. With many countries either unable or unwilling to support domestic spending while inflation continues, there has been a growing tendency to institute trade-restrictive policies to support domestic demand. The resulting weakened demand conditions in exporting nations have had a direct effect on the mineral industry.

Jan 1, 1982