Search Documents

By Robert H. Peters

Groundfall accidents have been the leading cause of fatalities in the underground coal mining industry for many years. Statistics from the Mine Safety and Health Administration (MSHA) indicate that approximately half of the victims of these fatal accidents were in an area where no devices had been installed to support the mine's roof. This report was prepared by the U.S. Bureau of Mines to summarize the opinions of 268 coal miners, 29 rust-line supervisors, and 30 MSHA inspectors concerning why people go under unsupported roof, and how to prevent this behavior. Interviews were conducted at six minesites.

Jan 1, 1991

Alabama ranked 19th in the Nation in nonfuel mineral value1 in 1994, down from 18th in 1993, according to the U.S. Bureau of Mines. The estimated value for 1994 was $576 million, a 2.5% increase over that of 1993. This followed a 3.5% increase in 1993 over that of 1992. The State accounted for a little less than 2% of the U.S. total. Nonfuel mineral production in Alabama consisted entirely of industrial minerals; no metals were mined in the State. Bauxite materials mined in the State are a natural mixture of bauxitic clay and bauxite having very low iron oxide content and are primarily used to make refractory (high temperature resistant) products, rather than in the production of primary aluminum. In descending order of dollar value, the top four mineral commodities produced in Alabama were crushed stone, portland cement, lime, and construction sand and gravel. These commodities accounted for almost 88 % of the State's total non fuel mineral value, while crushed stone and portland cement together represented almost 65 % of the total. In estimated mineral production for 1994, Alabama remained first in common clays and first of only two States that produced bauxite; third in lime, kaolin clays, and fire clays; seventh in portland cement and salt; and was one of the top seven States that produce bentonite clays. The State dropped from third to fifth in masonry cement. Production of talc and pyrophyllite resumed in 1994. Compared with 1993, the value of crushed stone, lime, construction sand and gravel, common clays, kaolin clays, fire clays, bauxite, and talc and pyrophyllite increased. Decreases occurred in portland cement, masonry cement, industrial sand and gravel, and dimension stone.

Jan 1, 1995

By Raymond B. Ladoo

Toward the end of 1920 , the average grades of ground feldspar offered to the pottery industry were so poor and so generally unsatisfactory that many of the largest consumers decided to take active steps for their own protection . A few of the potters made arrangements to grind their own feldspar , while others asked the Bureau of Mines to make a detailed study of the problem and to suggest methods of improvement . Accordingly such a study was undertaken, the partial results of which are outlined in this preliminary report . The outstanding features of the present feldspar industry which are of interest in this connection are stated below. (1 ) Many grinding companies do not own or control all or even a major part of their sources of crude material , but buy in job lots from many sources . (2 ) There is great need of more adequate engineering and chemical control over mines and mills . ( 3) ~ Out of date , inefficient methods and equipment for mining and grinding are in common use . (4) Little or no cooperation exists between feldspar producers , but on the contrary many feldspar companies are exceedingly secretive . This tends towards (a) preservation of obsolete methods ; ( b ) want of knowledge of the essential features of production , market requirements , and the relation between total milling and consuming capacities of the country; ( c ) inefficient and often mistaken trade practices ; ( d) unprofitable and even ruinous competition in dull periods . (5) The small size of many feldspar deposits precludes maintenance of an efficient organization at each individual mine . ( 6 ) Many of the best deposits of feldspar situated close to railroads are becoming depleted , which results in gradual lowering of grades , and increase in cost for better grades . (7) There is a lack of exact mowledge of the ceramic properties and behaviour of feldspar by some consumers , which results in ( a) purchase of feldspar on the basis of price alone , thus encouraging low production costs at the expense of quality , and ( b) inefficient and expensive cross- hauling of both crude and ground feldspar .

Jan 1, 1922

By Frederick C. Trutt

A guide to the development and utilization of an interactive mine-power-system fault program (Z-bus by algorithm) is presented. Theoretical foundations, as well as implementation considerations are discussed with respect to the mine-power system. Alternative Kron reduction techniques are presented along with a triangular-storage method for storage conservation. Program capabilities include the analysis of balanced and unbalanced (line-to-line, line-to-ground, and line-to-line-to-ground) fault situations using symmetrical component theory. To account for phase shifting in delta-wye transformers and zero-sequence network constructions, transformer and load configurations are specified by the user. The positive-and zero-sequence connections needed for network conformity are automatically constructed with the required impedances.

Jan 1, 1979

By W. D. Dietzman

This Bureau of Mines report presents a continuation of statistics pertaining to distribution of petroleum reservoirs (or fields), wells, and production by depth and producing rate classification in the United States. These statistics show the change that has occurred since results of a similar study were published by the Bureau of Mines in 1967. Data are presented in tabular form by State for the 18 principal oil-producing States and by subdivision for the two largest oil-producing States, Texas and Louisiana. Tabular summations and graphical illustrations are presented for the Nation. The data are classified by 4-barrel-of-oil-per-day rate increments up to 36 barrels and one increment of greater than 36 barrels of oil per day and by 2,000-foot depth increments up to 8,000 feet and one depth increment of greater than 8,000 feet. The overall average producing rates for States and the Nation have been published for many years, and although such rates are useful, they are very general descriptions of producibility. A breakdown of production, wells, and reservoirs by various depths and rates and by State or by State subdivision provides a more detailed description of producibility.

Jan 1, 1975

By T. E. Bernard

The CO2-absorbent canisters used in four approved rescue breathing apparatus were investigated. A breathing machine was used to simulate human expiration with gas flow rates of 26, 37, and 48 1/min of 3.5% CO2 in air. The exit gas CO2 concentration, the pressure drop across the canister, and the exit-gas temperature were monitored. The absorbent capacities of the packed-bed canister designs were found to be dependent on flow rate within the range studied, while the capacities of the other designs were less affected. The radial canister had the least resistance to breathing while the complex bed design proved to be the most effective in utilization of the chemical. The overall results indicated that LiOH (lithium hydroxide) has the highest capacity for CO2 absorption among the absorbents tested. It can be used in a simple packed-bed design while maintaining acceptable levels of resistance and exit-gas temperature. Examination of oxygen supply with respect to CO2-absorption capacity suggested that it is desirable to closely match CO2-absorption capacity with the avail-able O2 supply to minimize the size and weight of rescue breathing apparatus.

Jan 1, 1979

By Ruth F. Brinkley

This report is the 16th of a series of reports originally issued annually and more recently biennially to acquaint the reader with the work of the Explosives and Physical Sciences Division, Region VIII.3/ In the majority of instances the results of the investigations are made available to the public through Government publications and journal articles. In certain instances (specifically as regards security-classified research, investigations of a confidential nature, and short-range programs of very limited scope) results are reported only to those immediately concerned.

Jan 1, 1957

By Charles L. Harness

The barite industry has made notable progress since the days when barite was used only as an adulterant in white-lead paints and the only method of mining it was with pick and shovel. The following chronological record may serve to show how this heavy white mineral has grown in importance in the national exonomy and at the same time to indicate development of methods for obtaining it. 1845. - Barite first, mined in Fauquier County, Va., for use as an adulterant in white-lead paints. 1850 (approx.). - French settlers 60 miles southwest of St Louis, Mo., discovered barite; called it "'tiff;' meaning white. It was mined and shipped to St. Louis for use in paint.

Jan 1, 1946

By G. L. Oldright

The studies previously made on Smelting in the Lead Blast Furnace have dealt with the custom smelter of the International Smelting Co. at Tooele, Utah, and on the smelter of the Bunker Hill & Sullivan Mining & Smelting Co. at Kellogg, Idaho. The International plant may be considered representative of the traditional custom smelter. The lead smelter of the future seemingly will have to treat increasingly richer lead charges. This feature was then stressed in describing the Bunker Hill plant.

Jan 1, 1934

Mine drainage and mine reclamation are topics of major interest to the mining industry, federal and local governments, and the general public. This publication and its companion three volumes are the proceedings of a conference held in Pittsburgh, Pennsylvania, April 24-29, 1994. There were twelve sessions (69 papers) that dealt with mine drainage, including modeling, geochemistry, prediction, treatment, control strategies, characterization, hydrology, and case studies. These sessions comprise volumes 1 and 2. The six sessions (34 papers) that dealt with reclamation and revegetation of disturbed lands are included in volume 3. Volume 4 includes the six sessions (34 papers) that dealt with such topical issues as fires at abandoned mine sites, subsidence, hydrology, mine wastes, and policy. Poster session presentations are represented by 49 papers and 92 abstracts that have been placed in the back of volumes 2, 3, and 4, consistent with the subject of that volume.

Jan 1, 1994

By R. S. Dean

This is the fourth of a series; of annual report of the Metallurgical Division to be released in this form and cover the fiscal year July 1, 1937, to rune 30, 1938. This report is not merely a recitation or brief of the year's work; it contains technical information in usable form, although a some of this has appeared or will he issued in greater detail in separate reports. The table of contents that follows fists the principal investigations accomplished and those that are being continued. Other projects are being begun and contemplated for the next year.

Jan 1, 1938

By Secretary of the Interior

"INTRODUCTION The Bureau of Mines Synthetic Liquid Fuels Program again forged ahead during 1952, and important technical advances led the way to improved methods of converting coal and oil shale into liquid fuels. Marking the eighth year of activities under this program, the past 12 months brought a new domestic industry nearer realization.The increasing demand for gasoline and oil and the rising cost of finding new petroleum, coupled with America's growing dependence on imports and the unsettled international situation, have continued emphasize the importance of the Bureau's Synthetic Liquid Fuels Program. Oil, the indispensable material of wartime, likewise has critical importance in peacetime, touching as it does the life of every individual. Supplementing petroleum with synthetic liquid fuels will not only conserve this Nation's petroleum reserves but also will bring into greater use its tremendous reserves of coal, as well as the vast deposits of oil shale for which no other practical use has yet been found.The Bureau of Mines Synthetic Liquid Fuels Program is one of the most important and far-reaching of the Government's research projects. Through development, of commercial synthetic liquid fuels, the United States can obtain oil products from its great inland reserves of coal and oil shale to supplement petroleum in any quantity that may be necessary, consistent with economic and other requirements, such as national defense. The use of raw materials from such deposits would be of highest importance in wartime, when shipping lanes are menaced by the enemy. The Synthetic Liquid Fuels Program of the Bureau of Mines and research efforts of industry have advanced American technology to the point where it is now possible to begin the design and construction of prototype plants. Certainly, significant improvements will be made as the program continues, but this prospect in no way alters the fact that the start of prototype plants should be encouraged. These plants, as the first step in the development of a synthetic fuels industry, would serve a threefold purpose:"

Jan 1, 1953

By Paul W. Johnson

A computer program for calculating capital and operating costs from material and energy requirements and equipment costs for use in preparing cost estimates for metallurgical process evaluations has been written by the Bureau of Mines' College Park process evaluation group. The program permits rapid recalculation of processing costs when changes of data or equipment are desired, and produces tables of capital and operating costs suitable for publication. Equipment cost summary tables for each process section end supplemental information for input-data checking is included in the computer printout. The program is written in Fortran IV except for several subroutines which are written in machine assembly language for the IBM 7094.3 With a few modifications, the program can be used on other computers.

Jan 1, 1969

By Raymond B. Ladoo

"The name bentonite has been applied to a group or series of clay-like materials characterized by an alkaline oxide and alkaline earth content of 5 to 10 per cent, fine grain Giza, high absorptive powers, and usually very strong colloidal properties.Bentonite probably represents no mineral of fixed composition, and its physical properties vary considerably. The type material from Wyoming is light yellow or greenish yellow in color, but from other localities it may be cream colored, white, gray, pink, dark brown or even black. It is exceedingly fine grained, very plastic and highly absorbent. The appearance may be dull or powdeay, but a freshly cut surface usually has a waxy luster. Some varieties have the appearance of wax and may be cut into very thin, translucent shavings. The fracture of the type material is roughly conchoidal, that of other varieties is platey and shale-like, while still others have no typical fracture. Bentonite is highly absorbent; .hen wetted it will absorb more than three times its weight or seven times its volume of water. Some varieties when wetted with water expand to more than six times (some experimenters report eight times) their original volume. The wetted material is exceedingly smooth and soft and feels like soft soap. Unlike most clays, bentonite is easily fusible at a comparatively low temperature.Under a high-power microscope bentonite seems to consist of extremely small, more or less rounded, grains of uniform size, but the texture of most varieties is so fine that individual grains can not be distinguished.Some varieties when finely ground and thoroughly agitated with water will stay in suspension indefinitely, forming a translucent gelatinous mass. The addition of small amounts of acids or sodium chloride seems to have little or no tendency to raid coagulation or settling. Other varieties of similar analysis and appearance go into suspension more easily, but settle out again in a comparatively short time. It has been suggested that the material which stays in suspension indefinitely is a true colloid of the emulsion or lyophilic type."

Oct 1, 1921

By A. B. Hooker, L. C. IlsLey

Explosives have been fired electrically for several decades. Mountains have been tunneled, deep shafts sunk, extensive coal and metal mine workings excavated and, in times of war, railroads, buildings, bridges, and fortifications have been destroyed by means of electrically fired explosives. Modern engineering depends so much on explosives that their safe and efficient handling and especially their detonation are of prime importance to all those connected with the use of explosive agents. Electric shot-firing is only one method of igniting explosives, but it is rapidly spreading and because of certain inherent safety features should be encouraged. Data collected by the Bureau of Mines indicate that in the United States a large percentage of the blasting in quarries, shafts,· and tunnels, and from 15 to 25 per cent of the blasts in mining operations, are set off electrically. The Bureau of Mines is interested in electric shot-firing because of its use in mining, and especially because electric methods, when properly applied, are undoubtedly safer than other methods commonly used. Electrical problems of many kinds must be solved in dealing with the various phases of electric shot-firing. Success in using an electric detonator is closely linked with the resistance of its bridge, the resistance of its leg wires, and the insulation of its current-carrying parts. The proper layout of a circuit where a number of shots are to be fired simultaneously depends not only on the types of detonators that are used and their arrangement and interconnections, but also on the size and insulation of the wire leading back to the source of power, and even on the source of power itself. Various types of electric shot-firing machines have been developed, and these offer still another field for study. In investigations of electric detonators and electric blasting equipment, the oscillograph is valuable because it can record electrical activity over very short intervals of time. By its use more complete information about electrical performance can be obtained than by any other means.

Jan 1, 1926

By J. W. Thompson

MEANING OF TERM, The term "minerals" when used in grants or in reservations or instruments of conveyance is not limited to metals or metalliferous deposits, whether contained in veins that have well-defined walls or in beds or deposits that are irregular and are found at or near the surface or otherwise. Byron v. Utah Copper Co., Utah, 178 Pacific 53, p. 58. The term "mineral" in its commercial sense has been defined as any organic substance found in nature having sufficient value sepa- rate from its situs as part of the earth to be mined, quarried, or dug for its own sake or its own specific use. Rockhouse Fork Land Co. v. Raleigh Brick & Tile Co., - W. Va., 97 South- eastern 684, p. 685. CONSTRUCTION AND MEANING. It can not be said that the term "minerals" includes only such substances as are procured by tunnelling and shafting, as much gold is procured by placer mining and rich deposits of manganese and other like ores are found upon the surface of the earth and are some- times obtained without either quarrying or mining. Rockhouse Fork Land Co. v. Raleigh Brick & Tile Co., W. Va. ——, 97 South- eastern 684, p. 685. GRANITE AS MINERAL. It has been determined that granite was included in a grant of minerals. Rockhouse Fork Land Co. v. Raleigh Brick & Tile Co., -W. Va., 97 South eastern 684, p. 685. See Armstrong v. Lake Champlain Granite Co., 147 N. Y. 495, 42 Northeastern 186.

Jan 1, 1919

By Curtis A. Jones

Continuing interest has been shown in developing processes for extracting nickel and cobalt from low-grade domestic deposits of these metals and in improving existing methods. Of special concern is the nickel-recovery installation at Nicaro, Oriente Province, Cuba, operated for the General Services Administration. The Bureau? of Mines felt that a bibliography would help familiarize personnel at various Bureau of Mines stations and General Services Administration contractors with extraction methods both in the United States and in foreign countries. When this task was under way it became apparent that to compile a complete bibliography would require considerable time, so it was decided to limit the first part to the later literature and issue it independently, thus making it available sooner. The present work supplements the first part and extends the coverage to the earliest years of nickel and cobalt metallurgy.

Jan 1, 1959

By D. B. Taliaferro

[Recovery of core specimens from subsurface formations and their subsequent analysis are important aids in efficient development and operation of oil and gas fields. Core specimen first were obtained mainly for the geologic information they revealed; now they are on analyzed to determine many of the physical characteristics and conditions of the subsurface formations as well. Cores recovered from the producing formations may be analyzed for porosity, permeability, oil content, "connate" water content, and other physical and chemical properties of the formation, all to the end of furnishing enough data for making reliable estimates of the quantity and availability of oil and gas within reservoir and in devising efficient means for their withdrawal.]

Jan 1, 1939

By K. E. Stanfield

Oil-yield results are presented for 65 oil-shale sections in Piceance Creek Basin, Colorado, sampled during the period 1957 through 1963. Including previously published data, oil-yield results for 203 sampled sections have now been released by the Bureau of Mines to aid in appraising the shale oil potential of the basin. Oil yields of core samples (135 sets) were regarded as reliable bases for appraising the Mahogany-zone interval, but only 5 sets of cores sampled the deeper, lower-zone oil shales. Drill cuttings (68 sets) sampled the lower-zone oil shales, but their oil yields are principally indicative and should be confirmed by analyses of cores. More complete core sampling of the lower-zone oil shales is needed.

Jan 1, 1967

By Horace T. Reno

This information circular surveys the iron are industry of the world. It presents a comprehensive statistical record through 1970 of the U.S. iron ore industry and world trade patterns. The supply position of the United States and the other principal industrial countries of the world are summarized; detailed information is given on iron are production, consumption, imports, exports, mine capacities, substitutes, properties, and uses. There is a generalized discussion of the technology of mining and smelting iron ore, with a selected bibliography on the current state of these arts. The circular contains a summary economic account of world iron are resources, and discussions of the structure of the domestic and principal foreign mining industries, iron are mine employment and labor productivity, research and development, legislation, government programs, and strategic factors.

Jan 1, 1973