Search Documents

By R. J. Traube

The purpose of the Inherently Safe Mining System (ISMS) project is to develop continuous and conventional coal mining equipment and systems which will reduce the incidence of fatal and nonfatal accidents in the working sections of underground bituminous coal mines by application of existing technology. This 3-year program, initiated on 18 June 1971, is being conducted in three phases: ? PHASE I (8 months) Systems Analysis Concept Design Planning ? PHASE 11 (16 months) Design Procurement Manufacture Preliminary Testing ? PHASE III (12 months) Underground Coal Production Demonstration.

Jan 1, 1972

Reduce the danger to personnel and destruction of equipment caused by fires on surface coal augers. Approach: A reasonably priced reliable system which automatically senses a fire and activates dry chemical extinguishers, has been built and field tested. How It Works: Heat sensors mounted in the engine compartment and hydraulic hose areas detect the fire, usually before the operator does. This causes the system to automatically discharge A-B-C class dry chemical extinguisher through a fixed piping system.

Jan 1, 1976

By John R. Rhodes

The objective of this project was to investigate the feasibility of analytical techniques potentially capable of determination of Mg, Al, Si, S, Ca and Fe in 1 to 2 mg samples of respirable coal mine dust, in a total analysis time of not more than 10 minutes per sample, using equipment capable of being truck mounted for field-laboratory operation. It was not essential that the technique be non-destructive, but the chosen technique is, and this enables the analysis to be performed directly on the 37 mm diameter membrane filter on which the respirable dust sample is normally collected. The sensitivity requirements are therefore quoted in terms of the units of measurement, µg/cm2. The detection limit (3o of the background criterion) should be 0.5 µg/cm2 or less. The precision should be 5% or better, at concentrations above which the detection limit is not the determining factor.

Jan 1, 1972

By Donald James Butler

Problems resulting from underground mines in three inactive mining districts in Colorado were investigated. The purpose was to determine how these problems could be reduced or eliminated in new closings -- essentially by benefitting from lessons of the past. Mines in Leadville, Westcliffe and the Cripple Creek-Victor districts were evaluated. Two basic types of problems were found to exist in the districts: environmental degradation and hazardous conditions. Environmental problems result largely from acid and toxic drainage from the runes and from leaching of surface waste rock piles and mill tailings impoundment. The acid drainage contributes high levels of metals to streams and deposits sediment in the stream bottoms. Erosion of waste piles is a lesser problem. Hazardous conditions from open or improperly sealed mine shafts and adits, mine subsidence pits, and from deteriorating and unsafe surface structures are common to the three districts. These problems become worse with the ravages of time and vandalism. Engineering solutions which would correct or reduce many of these problems are presented. These recommendations should also be applied to new mine closures, however, more basic changes are needed to effectively implement improved mine closures. The changes must take place in the areas of legislation, mining practices and education. Legislated regulations should realistically reflect the needs of both the mine operators, protection of the environment and the best interest of the general public. Benefits should be provided for compliance with regulations instead of penalties being assessed for noncompliance. Hazardous conditions and environmental problems associated with mines can be alleviated through improved mine design and effective cloning procedures. Education should provide an appreciation by the general public of past and present problems facing mine operators. This will result in an improved mining climate which, in turn, will insure a continuing supply of minerals to meet increasing needs.

Jan 1, 1983

By Scott A. Stebbins

This Bureau of Mines publication presents a method for estimating capital and operating costs associated with the exploration, mining, and processing of placer deposits. To ensure representative cost estimates, operational parameters for placering equipment and basic principles of placer mining techniques are detailed.

Jan 1, 1987

By Margaret R. Egan

A study of the combustion emission products of rigid ventilation ducting was completed by the U.S. Bureau of Mines. The ducting was composed of fiberglass-reinforced polyester resin. Four properties of the ducting were evaluated: (1) propensity to ignite, (2) smoke characteristics, (3) gas emissions, and (4) heat release. Particle sizes, obscuration, optical densities, and production constants for gas and smoke were also calculated. These results provide comprehensive data about the emission products, detectability, and relative hazards of fiberglass-reinforced plastic ducting and other mine combustibles under realistic fire conditions.

Jan 1, 1990

By Sean Gallagher

Bolting large sheets of wire mesh screen (WMS) to the roof of underground mines prevents injuries due to rock falls. However, WMS can be heavy and awkward to lift and transport, and may result in significant spinal loading. Accordingly, six male subjects (mean age =45.8 years + 7.5 SD) were recruited to lift WMS in a laboratory investigation of the biomechanical demands. Biomechanical modeling was used to estimate external moments about L5-S1 for sixteen lifting tasks, using two sizes of WMS. Full-size WMS involved a two-person lift, while half-size WMS involved a one-person lift. Lifts were performed under 168 cm and 213 cm vertical space. Restriction in vertical space increased the maximum L5-S1 extensor moment from 254 to 274 Nm and right lateral bending moment from 195 to 251 Nm. Lifting full sheets of screen (as opposed to half sheets) resulted in an average 33 Nm increase in L5-S1 extensor moment. The L5-S1 extensor moment was increased by an average of 44 Nm (18%) when lifting screens positioned flat on the floor compared to an upright position. Relevance to industry: Large flexible materials are commonly lifted in industrial work environments, and may involve the efforts of two or more workers. The current study examines the low back loading associated with lifting large flexible screens and presents recommendations to reduce spine loading.

Jan 1, 2009

By Michael J. Beus

This Bureau of Mines report describes the development of load cells for measuring compressive loads in timber and lock-bolt support systems commonly used in. coal; metal, and nonmetal mines Design and evaluation is covered in detail to insure a reliable, accurate, and practical instrumentation scheme. The load cells are relatively inexpensive and adaptable to various size support systems. User-oriented procedures are emphasized, and design equations were reduced to a series of nomographs. Laboratory evaluation, destructive testing, environmental testing, and tests to determine the effect of extraneous loads were conducted. Field performance was evaluated in conjunction with ongoing Bureau projects at a metal mine in North Idaho and a coal mine in Utah. Load cells utilizing a titanium alloy as the cell body and weldable strain gages as the strain-sensing components satisfied the basic design and performance criteria, and with minor design modifications, the load cells can be adapted to many mining applications.

Jan 1, 1974

By W. W. Adams

Rock dust, as a preventive or limiting factor in explosions of gas and coal dust in bituminous-coal mines, was used in larger quantities in 1939 than in any other year except 1937 since annual figures first became available in 1930, Reports from mining companies to the Bureau of Mines revealed that 144,430,000 pounds of rock dust was applied to underground mine workings in mines that produced 126,635,677 short tons of coal during the year. This quantity of rock dust applied averaged 1.14 pounds for each ton of coal produced. Rock dusted mines were the source of 39.7 percent of the total production of bituminous coal from underground mines; 33.2 percent of the total number of underground workers were employed at rock-dusted mines, and 35.9 percent of the total number of man-hours worked underground at all bituminous-coal mines in the United States during 19719 can be accredited to mines so treated.

Jan 1, 1940

By J. H. East

"INTRODUCTION Diesel locomotives have been used successfully in underground mines of Europe for 18 years, and much has been written on the technical details of the design of these machines and the safeguards provided by the manufacturers. The actual conditions under which' the Diesel locomotives are used have not been publicized as well and consequently are not well-known. In 1945 the writer observed numerous Diesel locomotives working underground in coal and metal mines of several European countries and was favorably impressed with the practical approach to the safe use of this- type of equipment.Recent statistics showing the number of Diesel locomotives in use are not available now because of the World War, but the extent to which this type of mine locomotive was used immediately before the war is indicated by table 1, which classifies the number of locomotives used in several countries according to the type of power, such as compressed air, Diesel, and electric.Mining conditions observed by the writer in the European countries are very different from those in most coal-mining districts of the United States. The surface plants are larger and are permanently constructed of brick or concrete; numerous coal beds are worked through one shaft; the crosscut rock tunnels or levels, driven to intersect the coal beds, are lined with brick or concrete blocks where needed instead of timber; the coal beds dip more steeply and are not as thick as in most fields of the United States."

Sep 1, 1946

By W. W. Adams

Rock dust, as a preventive or limiting factor in explosions of gas and coal dust in bituminous-coal mines, was used in larger quantities in 1939 than in any other year except 1937 since annual figures first became available in 1930, Reports from mining companies to the Bureau of Mines revealed that 144,430,000 pounds of rock dust was applied to underground nine workings in mines that produced 126,635,677 short tons of coal during the year. This quantity of rock dust applied averaged 1.14 pounds for each ton of coal produced. Rock dusted mines were the source of 39.7 percent of the total production of bituminous coal from underground mines; 33.2 percent of the total number of underground workers were employed at rock-dusted mines, and 35.8 percent of the total number of man-hours worked underground at all bituminous-coal mines in the United States during 19719 can be accredited to mines so treated. Rock dust was employed chiefly in the larger mines, which numbered only 431 out of 6,016 underground mines in operation in 1935, according to reports from mining companies. The mines in which rock dust was used had an average of 288 underground employees per mine, whereas mines in which rock dust was not used averaged only 62 underground employees per mine.

Jan 1, 1940

By F. A. Penning

An experimental and analytical investigation was conducted on a recoverable pit bottom buffer. Work was conducted at the Colorado School of Mines using the U.S. Bureau of Mine-s free fall test tower. The four-sided butter, one of several designs by Cable Belt Ltd., was constructed of reinforced rubber slabs. The kinetic energy of falling weights, 1670 to 6000 lb, was absorbed by the flexure of rubber slabs loaded along their edge. A series of constant energy, 3000 ft-lb and maximum design velocity, 600 fpm tests were conducted. Static testing of the buffer established the load-deformation behavior. A large hysteresis loop plotted above and below the data published by the manufacturer. Creep was evident during; the loading Lend unloading cycle. Electronic instrumentation measured deceleration using your accelerometers; overall and intermediate movement was found from four displacement transducers; bending strains were recorded at four locations; and base reactions were measured by using four load cells. Data were recorded on tape and played back on a recording oscillograph. High speed movies were taken of all the tests. Symmetry of response and rebounds, when they occurred, were noted. From the displacement-time and load-time data, maximum decelerations were calculated by four methods and different assumptions. Good agreement was found from these approaches. Impact loads ranged from a low of 0.7 to a high of 6.1 gs. A dynamic computer model was written for the response of the buffer. Displacement-time, and acceleration-time plots show close correspondence with experimental data for the ten experiments. Data from accelerometers, displacement transducers, strain gages, and load cells are included. The computer program listing, and displacement-time acceleration-time plots are also presented.

Jan 1, 1980

In the USA, the National Institute for Occupational Safety and Health (NIOSH) does a lot of work and has provided news of interesting new developments. Marcia L. Harris describes an ?Explosibility Meter: ?In underground mines, coal dust explosions are prevented by the addition of rock dust sufficient to render the coal dust inert. Federal [US] regulations require 65% and 80% incombustible content in samples taken in intake airways and return airways, respectively, assuming a nominal coal dust size of 20% minus 200 mesh. The Coal Dust Explosibility Meter (CDEM), a hand-held instrument developed by NIOSH uses optical reflectance to measure the explosibility of a rock dust and coal dust mixture.? The CDEM is now commercially available. It provides real-time results during rock dust surveys instead of waiting weeks for laboratory results1. ?With real-time results, the potential for a disaster can be mitigated immediately. The CDEM displays the percent incombustible content as well as a colour indicating the relative explosibility of the coal and rock dust mixture. A red read-out indicates that more incombustible material is required to inert the coal and rock dust sample, while a green read-out indicates that the dust sample is sufficiently inert. When the mixture is marginally explosible, a yellow read-out is indicated. The red-yellow-green output depends upon the particle size distribution of the rock and coal dust mixture with the finer size fraction being more explosible.?

Jan 1, 2008

By Eugene T. Sheridan

The Bureau of Mines annually canvasses the peat producers in the United states and publishes economic data on the peat industry, based upon reports submitted by producers. This publication lists all producers that reported commercial production to the Bureau for 1960 and presents data on individual plants. The companies named herein represent virtually all commercial producers, although a few small companies may not have been canvassed as the industry has many small operations that operate intermittently. Output of the various companies listed ranged from a few tons to more than 50,000 tons. Peat is included in the Bureau's annual surveys of the mineral industries because peat is classified as a mineral fuel. Although none is used for fuel in the United States, peat is a potential source of energy and ranks as one of our large mineral resources. The domestic peat industry sells peat, chiefly, for use as a soil amendment for general soil-improvement purposes. During the past decade the industry has expanded rapidly with operations increasing from 45 in 1947-494/ to 115 in 1960. Output during this period has more than tripled, increasing from 131,782 short tons to 470,889 short tons.

Jan 1, 1961

By Thomas O. Glover

Cameroon's mineral industry continued to be dominated by crude petroleum. The country's economic development depended on the production and export of crude oil. Oil output was estimated to be 56 million barrels in 1984 compared with 47 million barrels in 1983 and 39 million barrels in 1982. The country's only refinery processed approximately 16,000 barrels per day of crude oil in 1984, operating at slightly over 50% capacity. This volume, however, supplied the domestic need for motor fuel and heating oils. Cameroon's economy continued to expand despite problems and setbacks stemming from the attempted coup of April 6, 1984. Gross domestic product (GDP) growth in 1984 was 6.5%, the same rate as in 1983. Offshore crude petroleum production was the chief factor in the sustained economic growth. The country also maintained a relatively strong balance-of-payments position through oil exports. Investment, ranging up to 25% of the GDP, greatly contributed to sustained growth. The oil sector contributed approximately 14% to Cameroon's GDP in both 1983 and 1984.

Jan 1, 1986

By Richard L. Fowler

[Study and development of sensing techniques and sensors were performed to aid shuttle car drivers in detecting, obstacles and in guiding the car along the face haulage route. Microwave, acoustic, and optical sensing techniques were considered as part of the feasibility study for obstacle detection. Various guidance techniques, including wire-following and rib-ranging were investigated. Active optical sensing was selected for obstacle detection to obtain the bear overage and sharp angular cutoff characteristics required within the packaging limitations defined by the shuttle car configuration. Rib-ranging guidance was selected to achieve completely self-contained shuttle car system which responds to the mine geometry without need for wires, stripes, or other path defining devices. Extensive hybrid computer simulation runs were performed to valuate various guidance techniques during the feasibility study. Subsequent simulation rues were performed to establish parameter values for the rib-ranging guidance system. The obstacle detection and guidance system was designed, fabricated and installed on a standard shuttle car. The system satisfied all applicable permissibility requirements of Schedule 2G. An experimental permit was issued to Bendix for operation in an underground coal mine. System evaluation tests were performed first above ground at the Bendix Research Laboratories. The simulation model was validated by these runs. Final testing wan performed underground in an operating mine with an experienced shuttle car driver. All sensors successfully demonstrated Chi predicted performance capability during underground face haulage tests. Dust did not Impair system performance and lens cleaning was not required during working shifts. Further development is required to achieve the desired obstacle detection performance Closed loop steering control with manual override is recommended o: mended for the lateral guidance e system. The guidance system should be an invaluable aid to low-coal shuttle car drivers where continuous mining machines are utilized.]

Jan 1, 1973

By Bruce E. Stauffer

The report recommends criteria for the design of safe surface mine haulage roads. Information relevant to road design at surface mine sites delineates vertical and horizontal alignment; subbase and surface materials; drainage; cross-slope, superelevation; runaway vehicle protection; and road and vehicle maintenance criteria. An appendix Is included which details the study methods used in compiling the final report information. A bibliography following the main text lists literature referenced for the report data and which is available as a valuable tool for use by individuals involved in haul road design.

Jan 1, 1976

This sheet explains your audiogram (hearing test) and gives some basic information about protecting your hearing. Keep it so you can refer to it later. What is an audiogram? • An audiogram is often called a “hearing test,” but there’s no pass or fail • It is a written record of your hearing levels • A series of audiograms can track changes in hearing over time • Your hearing threshold levels (the quietest sounds you can hear) are measured in decibels (dB) at different frequencies from low (500 Hz) to high (8000 Hz) Why should I get audiograms? • To measure your hearing ability • To identify hearing problems • To monitor success at maintaining your hearing • To see if noise exposure is affecting your hearing Do I have normal hearing? Compare your hearing threshold levels to this scale: -10 – 25dB Normal hearing 26 – 40 dB Mild loss 41 – 55 dB Moderate loss 56 – 70 dB Moderate/severe loss 71 – 90 dB Severe loss 91 – 100dB Profound loss [ ]

Jan 1, 2008

By John C. Machisak

THIS CHAPTER of the Minerals Yearbook (volume III) contains overall injury experience and employment data at bituminous-coal, lignite, and anthracite mines, coking plants, metal and nonmetal mines, metallurgical plants, and stone quarries in the United States for the calendar year 1956. Volume I of the Yearbook includes injury experiences and related employment data in the metal, nonmetal, and quarrying industries, and in the milling operations connected with the mining of those commodities. Volume II contains the injury and related employment experience of the coal mining, coking, and oil and gas industries. Reporting is voluntary on the surveys conducted by the Bureau of Mines to collect injury and employment data in the mineral industries, except in the coal-mining industry, where operators are required by Federal law to furnish the information requested.

Jan 1, 1958

In 1987 Wyoming became the largest coal producing state in the country. The state is known for its extensive coal resources and extremely thick coal seams. Wyoming's coal reserves total about 69.3 billion tons, or 14.2 percent of the U.S. coal reserve. Coal seams range generally from 10 to 80 feet in thickness, although one seam is 220 feet thick. The coal-bearing areas of Wyoming underlie approximately 41 percent of the state's total land area. Wyoming's coal ranges from lignite to high volatile bituminous. Most of the coal produced is subbituminous from the Powder River coal region near Gillette. The presence of coal in Wyoming was discovered before 1834 on the Belle Fourche River. The state's first mine opened in Carbon County in 1865, and with the completion of the trans- continental railroad, the demand for coal increased. Currently approximately 80 percent of Wyoming's coal production is shipped out-of-state to meet the growing demand for low- sulfur coal to fuel electric generating plants. Wyoming received conditional regulatory approval November 26, 1980. Its Abandoned Mine Land Program was approved February 14, 1983.

Jan 1, 1992