Search Documents

By M. G. Wallis

This report presents the results of a study to develop a detailed mining method design based on longwall mining with sublevel caving. The method is applicable to low-dipping coal seams 20 or more feet thick such as are found in the western United States. The report covers (1) the development and description of the mining method, (2) evaluation of the engineering feasibility of the design, (3) estimates of productivity and recovery, and (4) an engineering cost analysis and economic feasibility evaluation of the mining method design.

Jan 1, 1977

By Kenneth L. Whitehead

After many years of research, the occurrence of pneumoconiosis, black lung disease, among miners has been related to the mass of respirable coal dust to which mining personnel have been exposed. Congress passed Public Law No. 91-173 in 1969, which limited the dust concentration of respirable dust allowed in the mine working areas to 2.0 mg /M3 as of December 31, 1972. As a result of these restrictions, much work has been done in determining methods of either eliminating or suppressing respirable dust. The purpose of this project is to determine the state-of-the-art in continuous mining machine bit technology, particularly with regard to dust production.

Jan 1, 1973

By D. O. Kennedy

"INTRODUCTION During the recent war attention was directed to prevent the destruction of American industries by sabotage. By Executive order of Lay 19, 1942, the Bureau of Mines was required to conduct investigations and make recommendations that would prevent loss of production of essential war minerals. The Health and Safety Branch of the Bureau of Lines was able to extend its activities with minimum loss of time to include security surveys of the important mineral facilities in the United States.A Mineral Production Security Division was established in the Health and Safety Branch with funds appropriated for that purpose by Congress in April 1942. From July 1942 to July 1945 engineers of this division, under the direction of D. Harrington, Chief, Health and Safety Branch, and J. J. Forbes, Chief, Mineral Production and Security Division, conducted investigations of 1,560 metallic and nonmetallic mines and associated facilities in accordance with the requirements of the Executive order.PURPOSEAn analysis of losses in the production of minerals shows that failure or destruction of equipment either from deliberate or accidental causes produces essentially the same result. Maximum production is insured by the prevention of subversive activities, fires, and industrial accidents."

Sep 1, 1946

By David J. Kusler

This study is an appraisal of the feasibility of recovery and the possible chemical and physical uses of the limestone from the Greenbrier Formation in western West Virginia. Data on minability, occurrence, quality, and markets were obtained from published and unpublished sources and by a limited mail survey combined with personal contacts. The estimated costs of recovery by deep mining techniques are considerably higher than competitive surface and shallow subsurface operations. Compositional in formation available for this study was limited but indicated the suitability of the limestone for most physical uses and some chemical process uses in appraisal of the uses and demand reveals that immediate markets may be difficult to establish, but for some uses long-term prospects may be encouraging, especially if the quality of limestone would be suitable for lime manufacture or use as metallurgical fluxstone.

Jan 1, 1968

By L. G. Marshall

This report describes dredging and processing of sand and gravel from a glacial-fluvial deposit in the Raccoon River valley near West Des Moines, Iowa. Preliminary cleaning and separation of the sand and gravel at the dredge site with subsequent transportation to separate plants and the production and disposal of the various grades of aggregate material are also described. The geology of the deposit is summarized. A tabulated summary of costs in units of labor, power, and supplies is included.

Jan 1, 1963

By John E. Kelley

A method for measuring the spark-shower radiance of metals when abraded on a grinding wheel was developed by the Bureau of Mines for evaluating the sparking tendency of metals. The radiance was measured in units of emissive power per solid angle per area of the detector. Over 100 metals were tested and rated relative to commercially pure iron. The metals tested included elemental metals, iron binary and ternary alloys, iron-carbon ternary alloys, commercial steels, nonferrous alloys, and a few hard-metal compounds. Some alloys were synthesized; others were obtained commercially. Alloys that possessed good strength properties were emphasized for selection. The results indicate that the spark-shower radiance of plain carbon steels and carbon alloy steels was greater than that of pure iron. Certain elements, particularly vanadium and chromium, reduced the sparking tendency of iron. Stainless steels and particularly nickel alloys displayed low spark-shower radiance. Some metallic elements had much lower radiance than iron; others, much greater. Plain carbon steels, heat treated to a variety of hardnesses, gave radiance values that generally increased with increasing hardness. The effect on sparking tendency of an increase in hardness of an alloy steel was studied. The sparking tendency increased with an increase in hardness to a maximum, then decreased with a further increase in hardness.

Jan 1, 1974

By W. P. Yant

Canister-type gas masks Pave become an essential part of the equipment of many industries, not only for use in .emergencies, but also in performing normal operations of industrial processes and procedures, particularly where ventilation is not practically or economically feasible. They are also used widely for enhancing safety of operations which previous to the development of gas masks had been performed in harmful atmospheres. Since the inception of industrial gas masks the Bureau of Mines has been actively engaged in endeavoring to increase the efficiency and safety of these devices, and this bureau bas become a source of advice to manufacturers in producing devices of good quality and to industry in the proper selection and use of these devices. In order to give first-hand information and keep current with the demands and needs of industry it is necessary to perform investigations from time to time. This report deals with tests of certain types of commercial gas-mask canisters for protection against mercury vapor.

Jan 1, 1932

By Verne E. Hooker

Near-surface temperature measurements in two granite quarries show that diurnal temperature variations are significant to a depth of 1 or 2 feet, and annual temperature variations are significant to a depth of at least 25 feet. As a result, ground stress anomalies due to temperature exist near the surface, and their magnitude depends upon the time of day and the time of year. Rock stress and corresponding temperature measurements were made in one granite quarry over a rock temperature range of 33° to 81° F. Measured rock temperatures show good agreement with values predicted from one-dimensional heat flow theory. Calculated and measured stress-temperature coefficients for the two granites in this study are given. Thermally induced stress variations in near-surface rocks tested were as large as 1,690 psi from combined daily and seasonal temperature changes.

Jan 1, 1971

By Harold L. Rhodes

The Bureau of Mines has developed a method for determining the H2S content in natural gas samples. A gas chromatograph with a flame photometric detector was used to analyze samples with H2S concentrations ranging from 5,000 ppm to a minimum detectable limit of 0.01 ppm. A mass spectrometer was used to analyze samples containing H2S in amounts greater than 5,000 ppm. Methods are presented for preparing containers for H2S samples and for preparing standards using partial pressure and weighed standard methods, Sample collection techniques are discussed, as are analytical results which illustrate the loss of H2S while in the sample container and provide a basis for evaluating containers used for sampling and standard preparation.

Jan 1, 1979

This report presents the results of studies of Kennecott Copper Corporation's tailings embankment at Magna, Utah. The stability studies described were performed on only one cross section of the embankment, utilizing; data obtained from drilling, sampling, and testing, which was limited in nature. The main objective of the data collection was to provide background information to support the overall research effort. Because of this limited scope, it is not possible to evaluate the degree of safety or adequacy of the embankment or disposal system, and the information and data contained in the body of this report must be judged in that light. The first part of this report contains discussion of site geology and seismicity, pertinent information on the refuge disposal system, a discussion of the tailings materials characteristics, a summary of the engineering analyses, and A bibliography. The second tart (appendices) contains basic geologic and engineering data supporting the discussions in the first part of the report.

Jan 1, 1974

By M. R. Geer

Efforts to evaluate washery performance are nearly as old as the art of coal cleaning, and in former years there was no uniformity in either the methods used or the basic terminology employed. This situation, and the con- fusion it bred, prevailed until about the time of the First International Coal Preparation Conference in 1950, Largely because of the interest of the French coal research organization Cerchar, the subject of evaluating performance was given prime importance at this conference. As a result, there is now a much greater degree of uniformity in terminology and methods of expressing cleaning results. The International Standards Organization currently is working toward international standards of terminology and methods that should improve the situation even more. The various criteria that are used to evaluate the performance of coal- cleaning equipment fall into three categories, depending upon the extent to which they are dependent on the density composition of the raw coal; some are directly dependent, others are only indirectly dependent, and still others are substantially indenpendent.

Jan 1, 1962

By C. S. Tout

While investigating methods for determining the best temperatures for hot-working experimental stainless steels, the Bureau of Mines Albany Metallurgy Research Center developed a machine in which hot-twist tests could be made in a few minutes. This machine is similar to some used previously except that specimens are heated by induction instead of by radiation, and their temperature is measured by a calibrated radiation-detection unit instead of by a thermocouple. In. developing the technique for using the new machine, tests were made on specimens of medium-carbon steel, mild steel, and AISI (American Iron and Steel Institute) type 304 stainless steel. Tests also were made on as-cast specimens and preworked specimens of experimental AISI type 202, low austenitic stainless steel, and as-cast specimens of AISI type 301 experimental stainless steel. The optimum hot-working temperatures were determined for all types of steel tested. Also, data were gathered on the effects of test speed and temperature on torsional strength and the effect of twisting on tensile stress in the specimen.

Jan 1, 1962

By J. J. Demeter

Experiments were conducted in 2- and 4-inch-diameter standpipes to evaluate the effectiveness of standpipes as pressure seals. During the experiments, these standpipes conveyed Alan-Wood magnetite (60 to 230 U.S. standard sieve mesh) by gravity flow from one vessel to another of relatively higher pressure. The information obtained has been helpful in a Federal Bureau of Mines investigation of how to make either synthesis gas or hydrogen by a modified steam-iron process employing a continuous recycling stream of granular iron-iron oxide at temperatures of 600° to 900° C. In this process the mixture of granular material flows by gravity from a reduction vessel at low pressures to an oxidation vessel at higher pressures. Data from the 2- and 4-inch-diameter standpipes indicate that it would be practical to use a standpipe as a pressure seal between the reductor and oxidizer. Investigators found that, by gravity flow, the standpipe could convey the Alan-Wood magnetite against pressure gradients up to 1.07 pounds per square inch per foot of column height.

Jan 1, 1961

By Robert A. Elgin

The Leadville mining-district (fig. 1) covers approximately 8 square miles adjacent to Leadville, the county seat of Lake County, Colo. It is famous for its large production of rich ores containing zinc, lead, copper, gold, and silver. Some manganiferous ores also have been produced.

Jan 1, 1949

By R. T. C. Rasmussen

"INTRODUCTION This is the second report of investigations describing tests in full-scale commercial heats of steel-using electrolytic manganese having a purity of about 99.95 percent, produced in the Bureau's pilot plant at Boulder City, Nev. The first report dealt with tests in cooperation with two companies can the use,of electrolytic manganese in the manufacture of stainless steel. 3/ Plans aril cost estimates for reasonably large commercial, electrolytic plants based upon pilot-plant experience, as well as the comments of a number of concerns where electrolytic manganese has been tried, are contained in another publication.4/ The tests in cooperation with industry are part of the Bureau of Mines program of investigations of methods of utilizing low-grade domestic manganese ores, thereby the United States leas dependent upon foreign sources of manganese for metallurgical use. The Boulder City pilot plant already has demonstrated the feasibility of producing electrolytic manganese from several of the most important reserves of low-grade manganese ore. As the ferromanganese normally used by the steel industry represents the bulk of the Nation's manganese requirements, the usefulness and possi¬ble advantages of electrolytic manganese in the manufacture of steel must be established if electrowinning from domestic ores is to become an important factor of manganese supply.Preliminary arrangements for the cooperative tests at the Atlas Steel Casting Co., Buffalo,. N. Y., were made with E. L. Altenburg, vice president and general manager of the company, by A. A. Dow. 5/ The data on the tests at the Atlas plant presented herein are based upon reports of E. L. Altenburg and information obtained by the author during a visit to the plant to observe the initial trial heats with electrolytic manganese in the open-hearth and the electric furnace."

Nov 1, 1945

By William R. Vogel

The Bureau of Mines Minerals Information organization collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. This data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), to place the collection of mineral statistics on an annual basis. The most recent authority for the Bureau of Mines Minerals Information activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress), which strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral- material production or consumption.

Jan 1, 1988

The Full Scale Model Roof Bolt Test System described herein was designed, fabricated, erected, and installed by MSA Advanced Systems Division for the U. S. Department of Interior, Bureau of Mines, Spokane Research Center. It was furnished under USBM Contract No. 50271014 and Modifications. The test system is intended for use by the Bureau of Mines to run comparison tests on roof bolt systems. The mine entry cross section is made from special concrete pillars and roof slabs. They are constructed within a steel beam frame with hydraulic operated cylinders to apply loads that simulate the action of mining overburden. The frame is designed so it can be disassembled for replacing the concrete in subsequent tests. A computer and data acquisition system is furnished to control the load application and measure and gather data.

Jan 1, 1979

By John R. Parker

Work places of an underground coal mine are required (30 CFR 1719) to be illuminated while self-propelled equipment is used. Permissible machine mounted systems have been developed and applied satisfactorily to many mining operations. However, some low seam and thin seam equipment has been difficult to illuminate because reliable, direct current systems and compact, low output, low glare luminaires were not available. This program resulted in the design and prototype construction of compact, low glare luminaires and AC and DC power systems, particularly suited to resolving illumination problems on low and thin seam mining equipment. Design objectives were based on enhancing the prospects for thin seam illumination solutions through definition of a product which could challenge markets enjoyed by higher glare luminaires and through reduction of technical risks associated with any new product development as well as the MSHA certification process.

Jan 1, 1982

By Forrest T. Moyer

INJURY experience and employment data are presented in this (chapter for metal and nonmetal mines, stone quarries, sand and gravel pits, iron-blast-furnace slag plants, and metallurgical plants (including ore-dressing and nonferrous reduction plants and refineries) in the United States. Employment and injury experience data for all mineral industries are given in volume III. The 1963 figures are preliminary and are subject to revision. METAL MINES Preliminary estimates for the metal-mining industry of a combined fatal and nonfatal injury-frequency rate of 32.34 per million man-hours in 1963 indicate only a slight change from the rate of 32.00 in 1962. Metal operations had 41 fatal and 3,110 nonfatal injuries during 1963.

Jan 1, 1964

By William A. Hustrulid

An overall summary and the individual reports of eight workshops to determine research and development needs in western mining ore presented. Problem areas are identified, and recommendations regarding priorities, funding sources, and prime movers are made. The objective of this contract was to identify research and development needs for advancing mining technology as well as health and safety measures for western U.S. Surface and underground mining. This was accomplished by convening a series of workshops where problems could be thrashed out by producers of trona, uranium, open pit copper, underground salt (from the Midwest and New York), underground metal and nonmetal, etc. In addition to problems, future priorities, funding, and the desicion as to who should be the prime mover on R & D were discussed.

Jan 1, 1976