Search Documents

By Phil N. Bradbury

"During a routine belt tightening of all cost centers, the management at the Martin County Coal Surface Mines, located in Martin County Kentucky felt that a thorough investigation of the drilling and blasting program could possibly pinpoint areas where the cost could be cut without sacrificing production. Upon close inspection of the drill benches it was noted that the actual layout of burden,spacing and stemming varied a bit from the actual blast design that the management had outlined for the blasters. This paper will outline the method of reducing the drilling and blasting cost at the Martin County Coal Operation."

Jan 1, 1986

By John F. Mitchell

Large production blasts involving many series in parallel have long been a source of complication. When speed and accuracy are most necessary in blast preparation an efficient and precise method of wiring is required. After loading a large number of holes and being pressured for time, due to lack of daylight, equipment shutdown, etc., an effective hook-up plan can eliminate many last minute problems. It is the intention of this paper to offer a simplified wiring proceedure which when employed can save precious time and encourage efficient and economical utilization of blasting personnel and material.

Jan 1, 1976

By S B. Richardson, N T. Moxon, A C. Torrance

In many mining situations the energy released by an explosive is far too high and results in over fragmentation and excessive damage to the surrounding strata. Laboratory experiments have demonstrated that the shock energy of an explosive can be significantly reduced by surrounding it with an attenuating material such as a foam. The effect of this reduction in shock energy on fragmentation has been determined using model materials. A four fold reduction in the amount of minus 8mm material relative to an air decoupled charge of the same weight was obtained for a foam attenuator.

Jan 1, 1989

By S. Mandal, R. Singh

The demolition of structures with explosive though most rapid, safe and efficient requires planned blast design parameters with respect to geometric and strength properties of the structure to be demolished. The paper, here deals with successtil demolition of three old bridge piers by different blast designs. These piers were 11 m tall and very close to the existing bridge, The plan distance of the old piers from the existing bridge varied between 43 m and 14,25 m. The paper also deals with the mathematical concepts for the causes of such action of demolition/dismantling of structures.

Jan 1, 2001

By Robert E. Miller

Mass blasting of open stopes and pillars is a normal operating practice at Isa Mine. Three main parameters are used to classify the types of mass blasts. These are type of explosive used, blasthole diameter and system of initiation. Both electric and non-electric initiating systems are currently employed. The advantages gained by large firings are many. More efficient utilization of manpower, due to the concentrated and continuous charging, is achieved. There is no requirement for men to re-enter areas where localised ground conditions may have deteriorated and exposure of ringfirers to stope voids is reduced.

Jan 1, 1980

By Donald H. Matthews

The Society of Explosives Engineers is an international organization of over four hundred members involved in the explosives industry, with most members being active in the United States. The regulations imposed by regulatory agencies on the explosives industry have drastic effects far beyond the industry. Since explosives are used in mining, manufacturing, construction, entertainment, and art, all phases of man's activities, including fundamental needs for survival, are affected by how efficient the industry uses explosives. We, as members of SEE, must be sincerely concerned with both the quantity and quality of government regulation, and this paper spells out some of the problems caused by regulations and offers a solution.

Jan 1, 1980

By Thomas M. Keevin, Gregory L. Hempen

Natural resource agencies, under various regulatory authorities, are challenged with permitting underwater explosive use while at the same time protecting aquatic resources. Deciding on whether or not to allow use of explosives requires striking a balance between development and aquatic resource protection. A company's goal in underwater explosive use is to select methods that are both expedient and cost effective. Use of explosives is often the best alternative for engineering reasons or economic considerations. Over and above legal requirements, indiscriminate destruction of fish and other aquatic resources is not in a company's best interests because of concerns relating to public image, as well as the need to secure future contracts.

Jan 1, 1995

By P. D. Katsabanish

Air decking applications are examined using numerical modelling and the AutodynTM code. The mechanism of damage is illustrated and discussed. Air decking is shown to provide advantages over stemming when powder factor is maintained. The current effort does not support reduction of the explosives column in favour of air decking. In a similar fashion, bottom hole air decking increases fracturing in the area of the air deck, compared to when the same volume is occupied by inert materials; however air decking does not appear to reduce the requirement for subdrilling. The apparent discrepancy between the numerical results and some field observations reported in the literature is discussed.

Jan 1, 2005

By Thomas P. Dowling

Historically, laws controlling the manufacture, sale, transportation and storage of high explosives and regulations governing the use of explosives were formulated to prevent accidents or eliminate incidents that might jeopardize public safety. Many of the original laws and regulations regarding classification of explosives and blasting materials, tables of distances for separation and/or isolation of explosives, construction of storage magazines and methods of blasting were based upon empirical data, field experiments or scientific facts. During the past few years, however, it appears that some of the explosive laws and blasting regulations introduced and/or enacted by federal, state and local agencies seem to be based more on political expediency than on factual information or technical data.

Jan 1, 1976

By Charles B. Ingram, Neil E. Gehrig

The development of water gel explosive products has been the single most important development in explosive research and development since the invention of nitroglycerine and dyne-mite many years ago. m e Explosives Department of Gulf Oil Chemicals Company has been engaged in the research, development, manufacturing an marketing of slurry explosives and blasting materials for over twenty years. Explosive research and development is being carried out at the Jayhawk Technical Laboratory and the Underwater Testing Facility near Pittsburg, Kansas. There are fourteen manufacturing facilities geographically located around the country to serve the mining, quarrying, and construction industries with a complete line of explosives, blasting agents, and accessories. This paper discusses the Gulf slurry products, their properties, and uses.

Jan 1, 1977

By Kunihisa Katsuyama, Yuji Ogata, Yuji Wada

Test blasting was carried out to study the flying characteristics of rock mass caused in bench blasting. The quantity of explosives was increased from 7.6kg to 9.1kg and the Minimum burden was changed from 131mm to 451mm. The effect of condition for the characteristics of fly rock were considered. The fly rock was observed using the high-speed camera and video to study the flying characteristics of the rock mass caused in the bench blasting. Numerical simulation of fly rock was carried out using DDA (Discontinuous Deformation Analysis) method. It was clear that the DDA method can be applied in the simulation of fly rock caused in bench blasting.

Jan 1, 1997

By M-C. Lee, Shomaker, R. Turcotte, B. Short

This research program was undertaken to better understand the factors causing abnormal NOx fumes generation from blasting operations in surface coal mining. More specifically, unusual quantities of nitrogen dioxide and nitric oxide have been observed at several surface coal mines in the Powder River Basin, Wyoming. All these mining operations have several points in common: (i) Blasting is performed using gravity loaded emulsions or emulsion/ANFO blends (ii) Unusual NOx (Oxides of Nitrogen) emissions are observed mostly when blasting is conducted in the overburden as opposed to the coal seam itself (iii) The overburden consists of very weakly consolidated ground strata, providing relatively weak confinement conditions for the explosives, and (iv) Significant ground water is observed.

Jan 1, 2002

By S. J. Dillingham

One of the primary goals of every blaster is to achieve the optimum blast design. Too much focus on efficient design, however, can cloud certain issues and exposures that must be addressed if the entire project is to be considered .successful.. Due to the known human response to blast effects and inherent dangers present in the use of explosives, the potential for the project being delayed or shutdown, or the blaster and associated company being named as a defendant in a lawsuit, is always a possibility. Therefore, the blast design and associated project bid must incorporate sound safety contingences and procedures that address those .what-if. Scenarios that may arise as a result of vibration, flyrock, public relations, and job-site personal safety.

Jan 1, 2002

In situ, most Taconite is heavily pre-fractured; because of the high cost of comminution of taconite, maximum fracture of pre-existing blocks is desirable. Sustained borehole pressure plays a significant role in fragmentation, especially by penetrating pre-existing fractures. The distribution of explosive-induced energy in the burden in three dimensions was calculated. Data on the comminution of single particles was used, with the distribution of energies and the distribution of pre-existing block sizes, to calculate fragmentation for a case study. The calculation agreed well with the measured fragmentation. Sequential comminution events are much more efficient than single ones, and enhanced fragmentation may be possible with alternative blasting practices. Some important factors in the dependence of comminution on energy input are discussed.

Jan 1, 1995

By Michael E. Kovach

This discussion is an overview of an approach to drilling and blasting angle holes at Martin Marietta Aggregates. Method of determining burdens, hole depths, angle settings and explosive selection will be discussed in detail with an emphasis on safety and production. Such techniques and methods involve the use of hand-held surveying instruments such as the Abney level, pocket transit and inclinometer along with measuring tape and burden pole. An interesting method developed by Oscar Banfield a retired Martin Marietta and E. I. duPont engineer, for setting the proper angle on a drill will also be presented. This treatise is a discussion of the use of simple yet important tools and techniques a blaster should use to resolve both routine and complex problems encountered during quarry blasting operations.

Jan 1, 1992

By Qi Jingyue, Wang Zhongquian, Yang Nianhua

Qinling Tunnel is the longest tunnel in China. The rock stratum is very hard rock - intact mixed gneiss. At the beginning of the construction, drift-pilot excavation is very costly due to the use of regular drill and blasting methods. After tests on the acoustic impedance match between rock and explosive, watergel explosive, which has a high velocity of detonation and high brisance, has been used for hard rock blasting. In addition, different cut plans have been compared. It was found that four-large-hole cut is the most effective. And the number of drillholes and specific charge cut down and the average advance reaches more than 94% of the blastholes depth. Thus, the difficult problem of hard rock blasting in drift pilot is successfully solved, while safe and quick construction is guaranteed.

Jan 1, 1998

By Edward J. Walter

A vibration record is a complex of motions resulting from a combination of direct, reflected and refracted seismic energy that originated at a blast source. Multiple hole blasting using delays further complicates the motion in that overlapping of seismic wave trains may occur when delays do not fire in the programed sequence. This can result in variations in amplitude, frequency and wave-1ength of the vibration. Amplitude may be doubled, frequency may oscillate between the highest and lowest frequencies present and wave-length may approach doubling of the longest wave-length present. These effects can present serious problems to conducting a safe blasting program since increased amplitudes and lower frequencies present higher damage potentials for structures. The development of these effects is described and illustrated graphically to show how these effects can occur.

Jan 1, 1989

By J J. Mullay, G W. Anderson, C J. McFinley, J F. VanNorman, C J. Kefer

Previous work has shown that testing of precompression effects conducted on a small scale under simulated field conditions in actual rock provides a reasonable model for the evaluation of explosives and initiators under the adverse conditions encountered in production blasting. Using this methodology can result in greater understanding of the phenomena as well as the ability to predict performance. This effort has been extended to evaluate various parameters not previously studied in a controlled fashion. The present paper describes the use of this technique to study the effects of delay timing on precompression effects. Intervals from 25 to 150 milliseconds are included in the study. Both VOD measurements and damage estimates are utilized in the evaluation. The results demonstrate that timing delay between holes is quite important in determining the overall effectiveness of a blasting program.

Jan 1, 1994

By Denard A. II Brandt

Today I would like to share with you some blasting practices used in the thick coal seam mines of Northeastern Wyoming. I will begin by giving you a general overview of a thick seam coal operation at The Carter Mining Company's Rawhide Mine. I will then discuss the blasting procedures used at this operation. The Rawhide Mine is one of 13 mines operating in the Eastern Powder River Basin of Northeastern Wyoming. Approximately 23 billion tons of recoverable coal lies in the Powder River Basin. The Rawhide Mine is currently producing approximately 8 million tons per year. Rawhide is the 9th largest coal mine in the United States according to 1982 production. We also received the 1982 Sentinels of Safety Award for being the safest surface coal mine in the United States. Rawhide's permitted capacity is 24 million tons.

Jan 1, 1984

By P D. Kasbanis, Lyall Workman

The energy output of an explosive is typically calculated using an equation of state and computer applications. Results are reported as weight and bulk strength, either in absolute terms or relative to ANFO. The effect of the equation of state selected and the assumptions regarding the energy calculation are considered and interpreted for the purpose of blast design. It appears that variations in the heat of detonation which result from the selection of the equation of state and parameters associated with it are not sufficient to significantly affect blast patterns, explosive consumption and costs. However variations stemming from the use of "available energy" associated with a cut-off pressure are significant, suggesting in many cases large pattern expansions. The validity of the various approaches is discussed and blast design results based on the energy calculated by the different approaches are presented and evaluated.

Jan 1, 1996