Search Documents

By Jung-Hoon Ryu, Chang-Ha Ryu, Byung Hee Choi, Yang-Kyun Kim

Control of overbreak in tunnel blasting is one of the key factors affecting the construction expenses as well as safety. Overbreak causes an increase in the cost of construction by requiring an additional amount of shotcrete. In addition, blast damage to the final rock face may cause instability and rock fall hazards. For these reasons, controlled blasting is an indispensable routine in tunnel excavation in order to get a smooth face and to reduce damage to the final wall. We have experienced a very poor quality of excavation depending on the tunneling sites although a similar design of controlled blasting technique was applied. Field experiments over 40 rounds were carried out to investigate the cause of the poor results in tunnel blasting. In this paper, discussed are the parameters affecting the overbreak and some findings from the field experiments. Overbreak could be controlled considerably by adjusting some parameters before the efforts of developing a new blasting method.

Jan 1, 2004

By Dale S. Preece, Ruilin Yang

"Air-decking has been used frequently in blasting for many decades. It has been asserted that an air-deckcan alleviate excessive shock pressure from the detonation of a charge thereby producing better energy distribution in a blast overburden, for example. Research on air-decking has been active and various theories have been postulated that mostly support the effectiveness of air-decking for improved blast efficiency."

Jan 1, 2017

By Roger Favreau, Patrice Favreau

Without blasting there can be no roads, no hospitals, no factories, not even foundations for homes. Yet in 1960 the only way to design a blast was by trial/error. By comparison, bridges were already designed by calculations before being actually built. This was possible because equations based on the fundamental principles of science existed with which all the stresses in the bridge could be calculated. In 1960 no equations based on the fundamental principles of science existed with which the mechanisms that take place inside the rock mass during a blast could be calculated. Since then the main author made it the objective of his research to seek such equations, and to validate that they gave accurate answers by means of experiments in the field, experiments made in co-operation with mines, quarries and the explosives industry; results have been reported in some 90 publications.These equations now deal with essentially all aspects of a bench blast: the intensity of the shock wave and the fragmentation size distribution throughout the rock mass; the movement of all the fragments into the muck pile; the fly rock and vibrations from the blast; etc.; are presented examples of such equations. They are now assembled into a computer simulator called Blaspa accessible on the Web, with which one can design a blast just as a bridge is designed. An example is presented. The reason to design a blast by simulations rather than solely by trial/error is that if it leads to damage, it is only after the actual blast that the blast design is realized to cause damage. If however the blast design had been simulated before the blast, then the risk of damage is identified before the blast and is prevented by redesigning the blast. Examples of such situations are presented. The need to a void damage is very necessary because the public is becoming opposed to blasting. When a blast does cause damage, and people learn that the blast was designed solely by trial/error even though simulation was available and would have prevented damage, they become even more strongly against blasting; they may succeed in getting a quarry closed. Their objections to unchecked blasting are not unreasonable, especially as simulating a blast with Blaspa on the Web is a very simple procedure.

Jan 1, 2013

By Dale Preece, Vanessa Berg

This paper presents a two-pronged vulnerability analysis approach for treating minimally reinforced concrete (RC) structures subjected to explosive events. This work was motivated by a heightened interest in homeland protection involving both malevolent and accidental explosions and the need for assessment of critical facilities subjected to an explosive detonation. The first part of the analysis approach employs the commercial 3-D Eulerian-Lagrangian hydro-code AUTODYN, while the second part of the analysis employs Single-Degree-of-Freedom (SDOF) methods, each predicting the dynamic response of the minimally RC walls, slabs and columns to explosive loading. The concrete is treated with the newly developed RHT (Riedel, Hiermaier, Thoma) constitutive model, which accounts for failure mechanisms in brittle materials. Predictions from AUTODYN are verified using the equivalent SDOF reinforced concrete code, SPAn32, developed by the US Army Corp of Engineers and agreement between the results indicates a high level of accuracy in both methods of analysis, allowing for accurate predications of airblast-structure interactions and failure mechanisms.

Jan 1, 2004

By Chantale Doucet, Mario Paventi, Malcolm Scoble, Yves Lizotte

Laboratory studies in homogeneous material indicate that the area of new surfaces created by blasting is proportional to the energy imparted to the material. Field studies, however, show that fragmentation is also related to the rockmass structure. This paper reviews ongoing compilation of a comprehensive and integrated blasting database which is based upon field monitoring and laboratory testing. A priority application of the database is to support attempts to more fully understand structural control over fragmentation. Database construction and the relative importance of rockmass physical and mechanical properties are considered in the paper. A methodology for data collection prior to, during and after blasting is reviewed. Data summaries from three case studies of blast performance in surface and underground mines are presented. These illustrate various aspects of the methodology, which included image analysis to quantify the fragment shape and remnant geology evident in the muckpile as part of the evaluation of structural control over fragmentation.

Jan 1, 1994

By U. Steiner

Electronic detonators have been in commercial use for a decade, with an excellent safety record. This paper lists known incidents involving electronic detonators. Typical standards required by regulatory bodies for static electricity and electromagnetic fields are reviewed. The performance of some detonators is compared to these standards; in general the minimum standards are easily exceeded. The general resistance of electronic detonators to extraneous electrical energy that can be derived from the body of test results is compared to danger levels for exposure of humans to these energies; it is shown that electronic detonators can safely tolerate higher electrical energies than people can. This comparison includes comparable data for electric detonators, which are shown to be more vulnerable to extraneous electrical energy than people are. Electronic detonators also bring significant safety benefits in blasting due to their testability, two-way communications, reliability, programmability and precision. The links between these attributes and enhanced safety are discussed with examples from actual blasting. Although electronic detonators are usually more vulnerable to extraneous electricity than non-electric initiation systems, the paper shows that the net safety benefit in handling and blasting is in favor of electronic detonators, which are the safest initiation system that has ever been offered to the mining industry.

Jan 1, 2010

By Pierre DePasquale, Ricardo Chavez

Lowering of quarry energy consumption participates to answer both environmental and financial issues. The “EE-Quarry” European project, supported by the European Commission (EE stands for Energy Efficient), develops a new and highly effective modelling and monitoring Energy Management System technique to improve Energy Efficiency and move to a low CO2 emission rate in the nonmetallic mineral industry. Within this global quarry project, blast design, as the first link in the chain, has to be optimized in order to satisfy requirements of downstream operations. The authors have been developing and implementing an operational methodology using continuous field measurements and field adaptation methods for blast design. It drives the drilling and blasting work, aiming at a more energy efficient and environmentally friendly operation. Based upon actual local conditions (rock-mass assessment, face geometry, borehole deviations, etc.), blast patterns are optimized through a specific hole-by-hole blast design software. It provides a better and more consistent energy distribution, to achieve a better rock fragmentation, while avoiding explosive overconsumption. The software also calculates total energy inputs and the drilling and blasting contribution to Greenhouse Effect. Coupled with methodical fieldwork and variable density explosives, it has been leading to a real reduction in energy costs and greenhouse gas emissions. As the project is now reaching its final stage, demonstrations were conducted in various quarries around Europe. Several simulations were carried out and compared to the site data, in order to propose enhancements for the different phases (extraction, loading, hauling, crushing and transport) while bearing in mind the environmental impact of the quarry. This blasting methodology allows to assess the carbon footprint of drilling and blasting in conjunction with the downstream operations, thus to evaluate the global carbon footprint of quarrying. Copyright ©

Jan 1, 2015

By Thomas C. Rube, T S. Bajpayee

The Bureau of Mines conducted research to determine the safe operating conditions for using recycled (used) lubricating oil from mining equipment as a partial replacement for diesel fuel to make ANFO-type blasting agents. The use of recycled oil (RO) saves energy, reduces oil imports, and reduces mining costs.

Jan 1, 1996

By R. K. Wharton

A European Directive requires that an explosive which is sold or transported within Europe must meet certain essential safety requirements from 1 January 2003. The assessment and certification of such an explosive is undertaken by an Explosives Notified Body and if the explosive meets the requirements a certificate is issued that allows the affixation of a CE mark. The presence of a CE mark ensures the product free access to European markets. The paper examines the requirements of the Directive, identifies those explosives that come within its scope, considers the role of an Explosives Notified Body, and explains the process of applying for certification.

Jan 1, 2002

By Marco Antonio Falquete

Conventional detonators and blasting caps make use, as igniters, of flame-shock-, andfriction-sensitive primary explosives, such as lead azide, lead styphnate, mercury fulminate, etc, most of them severe toxic and environmental contaminants. Sensitivity of primary explosives is one of the main causes of injuries and fatalities in explosives industry and in field applications. Intense research for a reliable, safe, and environmental-friendly non-primary-explosives detonator was conducted by the industry in the last years. A new detonator is presented, containing no primary explosive, employing only environmental-friendly substances while keeping reliability of performance. A series of performance tests is executed in prototypes of different output energies, including initiation by flame, shock tube, thermo tube (IBQ’s proprietary spark-generating tube, presented at 2005 ISEE Conference), energy transfer reliability, and extreme environmental conditions (according to MIL-STD 331B, test C1 standards). Results are compared, when pertinent, with standard blasting caps of different energy outputs, and with standard primary explosives.

Jan 1, 2007

By Thomas Rupp, Michael Siegwart

The paper presents the vibration and sound emission measurement campaigns carried out in 2007 in preparation for the Ceneri-Basistunnel construction. We also present the vibration measurement campaign conducted during the construction of the Zimmerberg-Basistunnel. Both tunnels form an integral part of the Swiss Federal Railway Company Neue Eisenbahn Alpentransversale project (NEAT). This strategic project comprised the construction of several new tunnels. Its aim is the improvement of the existing infrastructure. The improved infrastructure will be able to accommodate a larger volume of railway traffic that is also crossing the Alps at higher speeds. The construction of the Ceneri-Basistunnel commenced in 2006. Both the Zimmerberg-Basistunnel and the Ceneri- Basistunnel are located underneath densely populated areas. Therefore, noise and vibration emissions have to be kept to a minimum and must not exceed applicable codes of practice. In order to identify the most appropriate blasting strategy for the yet to be constructed Ceneri-Basistunnel, blasting trials were conducted. The paper presents the findings of these trials and identifies ways to reduce both noise and vibration emissions from blasting. The construction of the first phase of the Zimmerberg-Basistunnel took place between 1999 and 2003. While the first phase is already in operation, the construction of the second phase has been postponed (commencement originally due in 2007). The Zimmerberg-Basistunnel connects the outskirts of Zürich with the city centre. As the tunnel site was not located close to the surface near populated grounds, no special measures were needed to reduce the noise emissions from blasting. However during the construction of the tunnel, the vibration emissions from blasting were monitored on more than 50 locations on the surface. The paper presents the analysis of some of the data. An emphasis is placed on the appropriate synopsis and presentation of data for documentation purposes.

Jan 1, 2009

By M Dandeneau, P I. Rajic, K D. Murphy, M B. Johnson, T J. Tope

"Manufacturers and users of energetic material [i.e., propellants, explosives, pyrotechnics (PEP)] generate unserviceable, obsolete, off-specification, and damaged items that are characterized as reactive waste. These items must be safely treated and disposed of or reclaimed/recycled, thereby controlling existing waste inventories at manageable levels. The most commonly used disposal and treatment method, particularly at U.S. Department of Defense (DoD) installations, is open burning/open detonation (OB/OD). However, regulatory constraints and the inability of operators toobtain permits required for treating these waste has led to the recent reductions and limited use of OB/OD treatment at many installations."

Jan 1, 1995

By Michael Wieland

The work principle from thermodynamics is used to model the shock and heave for explosives shot in rock or under water, with the latter compared to reported results. The work principle utilizes restrictions and constraints to yield a representative fit to the irreversible (natural) shooting process. The reduction of the internal energy of the reaction-zone yields the total expansion work (TXW), the resultant sum of the rock/water shock and heave. The restoration technique of forming a closed thermodynamic loop yields the reversible mechanical work (RMW) or the rock/water heave. The residual work that remains when RMW is subtracted from TXW yields the irreversible disorder work (IDW) or the un-dissipated (without loss) shock in the surrounding rock or water. The work principle renders an unequivocal relationship for the shock-loss factor, rather than the traditional roundabout formula for correcting the underwater gauge-shock of un-modeled explosives. There’s a novel heave-ratio factor that unquestionably rates the fit of results under comparison. Rock-shots are more complex in nature than underwater shots due to rock fracture and stratum rupture, though numerical resolution is worthwhile. The proposed rock-water-jelly (RWJ) model yields rough estimates, with rock-type results not wholly different from their underwater counterparts. Though reported underwater shots reveal shock and heave trends with respect to charge formulation ingredients, there are no such rock-shot results for comparison, since the relevant test measurements in rock remain difficult, if not intractable.

Jan 1, 2007

By Marilena Cardu, Mauricio Dompiri, Jacopo Seccatore

Blasting in geological bodies is an industrial process acting in an environment characterized by high uncertainties (natural joints, faults, voids, abrupt structural changes), which are transposed into the process parameters (e.g. energetic transfer to rock mass, hole deviations, misfires, vibrations, fly-rock...). The approach to this problem searching for the “optimum” result can be ineffective. The geological environment is marked out by too many uncertainties, to have an “optimum” suitable to different applications. Researching for “Robustness” in a blast design gives rise to much more efficiency. Robustness is the capability of the system to behave constantly under varying conditions, without leading to unexpected results. Since the geology varies from site to site, and often from bench to bench on each site, setting a robust method can grant better results in varying environments, lowering the costs and increasing benefits and safety.

Jan 1, 2011

By Felipe França Sitonio

Parameter’s control of explosives used in blasting operations have become more relevant over the years, bringing a better understanding of detonation performance. Giving into consideration that bulk emulsion density’s variation reflects directly on blasting results due to its importance in product sensitivity and velocity of detonation (VOD), blast designs are conducted assuming that cup density measurements are reliable and explosives gassing agents will perform as per specifications. Nevertheless, confinement conditions in boreholes like temperature, presence of water and surrounding circumstances of rock mass are often neglected on predictive modelling and off-site measurements. This paper describes the assembly of a device equipped with pressure sensors and its utilization in confined boreholes of an open pit mining operation, aiming to obtain in situ monitoring of density variation in several explosive columns. After we developed a software to get and process data of a hardware prototype and the device functionality was validated in water, oil and quarry mining experimental trials, 7 of 291 boreholes in a gold mine operation were chosen to be monitored with two probes each, placed at the top and at the bottom of the explosive column profile. The results obtained enabled a comparison between the bulk emulsion density variation when acting in different environments, since we selected boreholes with diameter of 101.6 mm (4 in) and 139.7 mm (5.5 in) and some with presence of water. Besides the increase of explosive density with depth related to hydrostatic pressure increase, we found an overall error of 6% in cup density measurements when compared with sensors placed at the bottom of boreholes and 2% when compared with sensors placed at the top of explosive column. These findings provide detailed insights into how bulk emulsion explosives behave in different circumstances including depth and borehole diameter, giving the opportunity to re-evaluate blast design parameters such as its geometry, sequence pattern, charging profile and explosive composition.

Feb 2, 2020

By J. P. Proulx, Richard O’Meara, Ruilin Yang

A blast optimization project was carried out at an Open Pit Metal Mine using the Multiple Blasthole Fragmentation (MBF) Model and the Multiple Seed Waveform (MSW) blast vibration model. The aim of the project was to optimize rock fragmentation of the ore blasts to significantly increase metal recoveries while keeping the blast vibration levels at the highwall under control. The project also examined the blasts in the waste rock using the Fragmentation model to expand the blast pattern and select economical explosives for drill and blast cost savings while minimizing any adverse effect on the dig rates. Two sets of near field signature blasthole tests were conducted in both hard ore and relatively soft waste rock. The information from the near-field signature blasthole vibration was used as input to both the MBF and MSW models, as site specific geological information interacting with blasting. The implementation of the full blast design is also input to the MBF and MSW models. A production blast for each rock type was monitored for blast vibration and rock fragmentation. The full blast information and the blast results are used to calibrate and validate the models. The Fragmentation and Vibration model were established for the two rock types at the mine. At each site the Fragmentation modeling was conducted in parallel to the Vibration modeling to ensure blast vibrations were under control while the rock fragmentation was improved. The Fragmentation MBF and MSW are each an integral part of the blast optimization tool. Various scenarios using different explosives, hole delays and blast patterns were modeled for rock fragmentation and blast vibration. The recommendations from the modeling project were to be field trialed at the mine. The implementation of the recommendations was expected to help the mine significantly in terms of the mining economics, and high wall stability and safety.

By Benjamin Cebrian

Rock blasting at quarries represents multiple challenges not easy to see at first sight. Aggregate industries face similar or superior prices for explosives while extracting a material that usually is of less value of metal mining operations. Therefore, learning to optimize a quarry operation can be a perfect training for a position in blasting at larger metal mining operations.

Jan 1, 2010

By Robert Jacob Cefalo, Rio Tinto Kennecott

At the end of 2016, the Mine started a new ore phase in the section of the pit located on the East Wall. The East Wall geological structures required controlled blasting for peak particle velocity (PPV) frequency vibrations to protect the wall. Frequency controlled blasting using linear seed wave superposition modeling was required and implemented to reduce the far-field affects to the wall. This paper covers the work done by the drill and blast engineering group, controls used to protect the mine infrastructure, and the continuation of work-to-date of frequency controlled blasting for wall stability. The narrow width of the layback required the combination of hole sizes to blast large diameter production patterns with smaller diameter trim patterns in the same blast. A single blast had to use different burden & spacing and hole diameters and required the use of different timings throughout the pattern. Electronic detonators were required to limit blast vibrations and accommodate the specific timings needed to reduce low frequencies. The geotechnical group with the help of geotechnical radars worked with the drill and blast group on creating a tracking and reporting of blast performance. The radar readings informed the drill and blast engineers of the performance of the blast as it related to the long term performance of the highwall

Jan 1, 2019

By Michael E. Curtis

This paper outlines a study performed to analyze the advantages of utilizing a blasting agent with a velocity of detonation that is 1.3 to 1.4 times the P-wave velocity of sedimentary shales and sandstones at a major Midwest coal operation.

Jan 1, 1997

By AK Chakraborty, AK Raina

Burden of drill hole is third most sensitive parameter effecting the ground vibration in blasting apart from maximum charge per delay and distance. Various types of burdens can be seen in practical bench blasting situations. Burden can be expressed as drilled burden and initiation burden. Drill holes may have various front row burdens (toe burden), which may be different from the designed burden. In order to ascertain the impact of front row burden as well as the initiation burden on intensity of ground vibration and air overpressure experiments were conducted in sandstone overburden benches of an opencast coal mine and limestone quarry. Blast trials were carried out in cognisance of both drill and initiation burden while keeping all other parameters constant. Effect of front row burden was also extensively studied by keeping almost all other parameters constant. The results of the study reveal that there is substantial influence of front row burden on the vibration and air overpressure. The statistical analysis of vibration and air overpressure data with drilled burden and initiation burden gives significant evidence that the level of peak particle velocity of vibration (Vmax)) is reduced by reducing effective burden with modification of initiation. Data analysis carried out for air overpressure versus initiation burden shows that reducing effective burden with modification of initiation results in increasing the level of P. The study reveals a qualitative assessment of the influence of burden on the blast induced vibration and air overpressure. The study also recommends to modify the initiation pattern to reduce the effective burden in order to reduce the vibration, without disturbing the fragmentation.

Jan 1, 2004