Search Documents

By Klaus M. Hahn, Hermann Wotruba, Bernd G. Friedrich

"Due to an increasing demand for nickel and cobalt and the depletion of nickel sulphide deposits worldwide, the production of ferronickel from lateritic nickel ores becomes more significant. About 60 percent of nickel reserves are present in laterite deposits. Common production methods like acid leaching or smelting operations implicate high material and energy consumption. Physical processing methods are also not efficient, because of the fine microstructural intergrowth of the minerals carrying valuable elements such as nickel and cobalt. Due to the high energy consumption of metallurgical treatment of lateritic nickel ore (nickel grade: 0.8 - 3.0%, Co: 0.05 - 0.15%), the separation of waste material (about 75 - 85%) before the metallurgical treatment is desirable. Therefore, an alternative process has been developed, combining a pyro-metallurgical pre-treatment with selected mechanical processing methods. The developed process consisted of a selective pre-reduction and non-selective segregation of the contained metal phases in the first stage. By this, the properties of the metal carrying minerals were changed and could become subject to concentration by means of fine beneficiation processes afterwards. The parameters of the pre-reduction and segregation were varied and the pre-treated samples were examined concerning their efficiency of metalization grade and metal grain size. This paper describes the investigation of pre-treatment methods of a lateritic nickel ore. The pre-treatment and possible subsequent separation methods were examined with regard to the recovery of the valuable elements. Metalization grade was around 80% for both Ni and Co with metal phase grain sizes below 20 µm. Scanning electron microscopy revealed distribution of new metal phases not only on the reducing agent, but also on the “slag” material.INTRODUCTION Nickel laterites are characterized as strongly weathered regoliths with several zones containing reserves of nickel (Ni) and cobalt (Co). These laterites are formed on serpentinites and ultramafic rocks under climatic and/or tectonic conditions that have changed over time (Butt & Cluzel, 2013). The formation of Ni laterites is influenced by numerous geological and environmental factors. In general, there are three ore types named according to the dominant Ni hosting minerals: oxides, hydrous magnesia (Mg) silicates and clay silicates (Butt & Cluzel, 2013). The most Ni laterite deposits contain two of these ore types, usually an oxide zone and an either clay or Mg silicate zone. Distribution of these principal deposit types, their average Ni-bearing phases and mean Ni grade are shown in Table 1. A schematic profile of the different deposits based on the development on serpentized ultramafic rocks is given in Figure 1 (Butt & Cluzel, 2013)."

Jan 1, 2018

By G. P. Wong

"In the Inco matte separation process, a slow-cooled converter matte is separated into three main discrete mineral phases: chalcocite (Cc), heazlewoodite (Hz) and a Cu-Ni-Fe alloy. After magnetic removal of the alloy, Cc and Hz are separated by flotation at pH>12 with diphenyl guanidine (DPG) as both collector and frother. High selectivity is achieved in rougher flotation. However, in later flotation stages such as in the middlings circuit, as oxidation takes place, Hz becomes highly floatable, resulting in a very poor separation between Cc and Hz.Starch and dextrin as Hz depressants were evaluated on the middlings circuit feed and showed no positive impact on Cc/Hz separation selectivity. Ethylene diamine tetra-acetic acid (EDTA) extraction showed the existence of abundant surface Cu and Ni ions. The use of triethylene triamine (TETA) or EDTA in flotation did not improve Cc/Hz separation selectivity. Microflotation tests were carried out on pure synthetic Cc and Hz minerals. It was found that Hz did not float in the presence of DPG. However, Hz conditioned with either copper sulfate solution or in contact with Cc floated readily in the presence of DPG. It is concluded that the major reason for Hz flotation in the middlings circuit is due to Cc oxidation releasing Cu ions that adsorb on the Hz surface making it reactive with DPG thus rendering the Hz floatable."

Jan 1, 2003

By Manochehr Oliazadeh

"Water shortage becomes a major challenge in mining industry. The best example is Chile where the Chilean authorities declared a state of emergency in 2012. Depletion of high grade ore-bodies necessitates the use of low grade ores. If the demand for metals remains constant, more low-grade ores need to be mined to produce the same tonnages of metals. This increases the water demand in mining industry. Mining industry competes with other industries such as agriculture and manufacturing. Agriculture and manufacturing consume 1500 and 2300 billion m3 water respectively. The global use is 4500 billion m3 while the mining uses 80 billion m3 of water per annum.To tackle the water challenges in mining industry and also avoid competing with other users for fresh water, many efforts have been made, including using lower quality waters to reduce the fresh water consumption in ore processing. Saline water or hyper saline water from seas or the ground is accessible; however the cost of desalination is remarkable. Desalination plants and associated pipelines and pumps capital cost can easily exceed $ 500 million. Saline water will certainly increase the operating costs due to high wear rate of mechanical equipment but at current situation of mining industry spending all this money upfront does not look attractive. Desalination leaves salt on land at mine site which may create environmental issues.Dry processing can be a solution for water shortage in mineral processing. Wet processes dispose tailings on land with little or no agricultural productivity. It also may contaminate surface and ground water and generate dust. This paper reviews the water consumption by various mineral commodities, discuss briefly about recent of application of salt water in mineral processes and finally discuss about dry processes as alternative solution for water shortage in mining industry."

Jan 1, 2014

By B. K. Gorain

Mining of low grade deposits along with the necessity to design and operate flotation plants with high throughput presents unique metallurgical and environmental challenges that need to be addressed to reduce project risks, improve project economics and to sustain the profitability of operations over the life of a mine. Some of the key challenges include poor recovery of valuables and concentrate quality issues due to complex mineralogy, the need to use poor quality water such as brackish or sea water, reduce environmental impact from the process, integrate flotation with hydrometallurgy to maximize precious metals recovery, escalation of capital and operating costs, use of unproven technology and constant use of larger equipment, high ore variability, worldwide constraints on resource availability and an ever increasing need for reliable metallurgical input to financial models to evaluate economic viability of projects. The need to develop effective solutions to these problems in a short time frame is becoming a key to the success of any new project and for sustaining the profitability of a mining operation. An integrated multi-disciplinary approach to problem solving is crucial with the need for a more lateral thinking along with strategic partnerships and collaboration involving the right players. This paper presents some of the key findings based on experiences from a large number of challenging projects and operations focused on solving complex flotation problems Keywords: mineral processing, flotation, flotation problem solving, flotation optimization, plant design, innovation

Sep 1, 2012

By M. Kalicinski, M. Lyssyy

"Access to information is a key component for making improvements to any process. This is particularly true for all aspects of the iron mining and steelmaking process. The ability to make rapid control decisions can significantly influence process outcomes, including ensuring product specification, mining quality, transportation limits, upgrade factors, waste bypass and direct shipping, among many others. While traditional laboratory methods provide feedback for such processes, having access to analysis results in real-time can lead to positive reactive and predictive control decisions to be made rapidly, leading to significant improvements throughout the process. Scantech has been designing, manufacturing and supplying technological products to the minerals industry since 2002 to enable the availability of such real-time information to a mine or plant, with the benefits being enjoyed by a wide range of operators. This paper provides a summary of the available technologies used in the iron ore and steel industries, as well as providing case studies of their use in African and Australian iron ore and European steel, as well as a description of the potential benefits of a range of analysis equipment.INTRODUCTION Access to information is critical for any process, and is a fundamental component for making process control decisions. In order to yield effective processing outcomes, it is important for that information to be readily available, preferably as quickly as possible, and to be as accurate as possible. While speed and accuracy are often traded off against each other, there are numerous technologies available in a processing environment that allow for both rapid flow of information and a high level of accuracy. The use of on-belt analysis equipment has a long trusted history of use in a number of mining and processing environments and industries, providing information such as elemental composition and grade of conveyed materials, moisture content, waste proportion and energy information. Australian company Scantech has been a provider of such equipment since 1981, and has become an industry leader in both the supply and development of on-belt analysers across a range of industries."

Jan 1, 2018

By X. L. Song

A large amount of tailings in concentrators bring a series of problems to the environment and society. It is significant to reclaim the huge tailings and reuse them in industries in order to utilize mineral resources adequately. Primarily Lead-Zinc tailings with a certain quality of clay and feldspar were used to produce ceramic tiles by sintering method under specific technical conditions. By testing the properties of the ceramic tiles, it was shown that the amount of Lead-Zinc tailing used in the tiles was 60%~70%, and the mechanics properties were good. The optimum proportion parameters were Lead-Zinc tailing 60%, clay 35%, feldspar 5%, and the maximum flexural strength of tiles was up to 38.2MPa when it was sintered at 1090? for 30min. Its flexural strength, water absorption and thermal shock resistance reached the State Standard of GB/T4100.4. The product is suitable to be used in pavements and paths of parks.

Jan 1, 2014

By J. C. Wilmot

The chemistry of aqueous cyanide containing species in the presence of reduced sulfur sources was investigated. Reactions were studied as a function of time and tracked using novel analytical techniques developed for the analysis of the species of interest in the sample matrix. Species of interest in this work were ?free? cyanide, thiocyanate, cyanate, metallo-complexed cyanide, and various sulfur and sulfur-oxygen species. The studies were conducted under constant temperature conditions at pH values above 10.5 and in the absence of light in order to eliminate photochemically induced cyanide reaction effects. The reaction products of cyanide when in contact with pure sulfur, pyrite, pyrrhotite, sphalerite, and cinnabar are reported. These data combined with data for cop-per, arsenic and lead sulfides, which have been previously published, are used to predict the fate of cyanides in refractory gold ores containing sulfides. A mass balance on the cyanide reaction products was completed for all experiments. From these studies insight into the chemical relationships of cyanide, the specific metal sulfide, thiocyanate and cyanate have been gained. When looking at the results of the experiments, it was immediately apparent that even though the overall conversions of cyanide to thiocyanate were different, most of the samples exhibited a similar pattern of reactions. The recovery of cyanide in these experiments was better than we expected, averaging in most experiments to be over 90 percent. Based on this research, the formation of cyanate was probably the main route of loss. The pathway choice for the various minerals was also elucidated in these experiments. The competitive oxidation pathways that cyanide can take have been tracked for sufficient time to determine the ?final? fate of cyanide in a process. Initially, it was thought that the cyanate may be involved in a hydrolysis reaction to form ammo-nia and carbonate ion, but upon further inspection of the data, there was not the drop-off in total cyanide recovery that would manifest itself were this to happen. On the other hand, the hydrolysis of thiocyanate to cyanate and sulfate would require oxidizing conditions which did not exist in solution at the beginning of the experiment. If the solutions were to be sufficiently oxidizing in nature for this to happen, the initial amount of cyanide would have been converted to cyanate quickly. The data support premise that the ?hydrolysis? of thiocyanate to cyanate and sulfate occurs to some extent in the experiments conducted. Knowledge gained from the experiments with pure metal sulfides helped interpret the results of experiments with refractory ores found in the State of Nevada.

Jan 1, 2014

By Z. H. Liu

We experimented with slurry which from one of coal preparation plant in Guizhou province and made researches on double hump gradation, one of critical factor of gradation technology, which can influence pulping character in the process of making coal water mixture (CWM). The purpose for it is to find the best particle gradation which can meet the requirements in concentration, viscosity, and stability for CWM. The final result is that the concentration, viscosity, stability of CWM can meet the requirement for industrial use while the rate of fine particle in the slurry is 70%~75% and the maximum concentration of 62%.

Jan 1, 2014

Mineral processing is an energy and water intensive activity. Mill comminution equipment usually has high energy requirements which necessitate extensive cooling to remove heat. Cooling requirements are typically 10% to 20% of the comminution energy. If there is an adequate supply of suitable water, open water-based cooling systems are the simplest, cheapest and most energy efficient cooling method available. This paper describes a method to determine the water demand for open water-based cooling systems at a plant and to determine whether the mine has sufficient water to meet that demand.

Jan 1, 2014

By P. M. Solozhenkin

"Galvanochemical process (GChP)) cleaning of sewages is realized in the field of shortcirquited galvanic elements from the mixture current the materials place in purification’s solution and form multitude galvanopairs without external electric field in presence oxygen of the air. The galvanochemical process is electrochemical process utilizing galvanic pairs: coke - iron, iron - copper and others and process does not require chemical reagents.The effect of basic parameters of the cleaning effectiveness have been studied depending on oxidizing of galvanopairs. Adjusting nature, type of galvanic pairs and forming three component system possible to enlarge emf circuits to 2.378 V.The role of ?2, as basic agent, for generation of hydrogen peroxide and hydroxyl ions.It was stated, that removing of metal ions from solutions occur mainly on account of sorption and hydrolytic sedimentation of iron oxihydrates.Determined separate stages of the process: coagulation, sorptions of admixtures on freshly formed ferric oxides and oxidizing destruction of organic components of effluents in presence of ?2 ? ?2?2. Shown efficiency of the method for removing of Cu, Cr, Ni, Zn, As ions, as well as fluoride, phosphate and cyanide anions and oil products, surface-active and flotation reagents. Cleaned water can be recycled for some processes non-critical toward residual concentration of admixtures, as total salt contents is lowered on 60-75 % and reaching limits of concentration for toxic components.The concept of high power unit creation was developed, and galvanochemical pulsator is presented. The pulsator is not expensive, and exploitation expences are low, as well as servise is simple with high effectiveness, and capacity. The galvanoflotation process is developing, combining galvanochemistry and flotation of hydrofobic admixtures (oil, surface-active agents).The galvanochemical flotators are presented."

Jan 1, 2003

By Robinson Irarrazabal, Edison Collinao, Rodrigo de Carvalho, Patricio Davila, Marcelo Tavares

"In recent years, DEM (discrete element method) softwares, along with 3D laser measuring equipment, have become powerful tools to describe mill charge behavior, as well as forces acting on the liners of SAG mills. With the aim of contributing to streamline this application of the advanced technologies ME Elecmetal and Universidade Federal do Rio de Janeiro, UFRJ, proposed a new approach to improve the design of mill liners using elements from mechanistic modeling of grinding. The paper presents a methodology for continuous improvement of liner design, which uses information from the DEM collision energy spectra in the mill discriminated for the different components (ore and steel balls), as well as information on the breakage properties of the ore being ground. From these it proposes the concept of "effective collisions", which corresponds to the collisions that are of sufficient magnitude to cause breakage, thus allowing to discriminate from impacts that do not cause breakage either in a first impact or after repeated loading. It also tracks the collision of steel balls against the shell in order to assess their potential damage to the liners. An industrial case study is presented of a 38’ diameter SAG mill, which was experiencing challenges associated to liner breakage and low efficiency with the old liner design. Through a modification of the liner design, simulations demonstrated the potential benefit associated to reduction in ultraprojection and improvement in mill capacity. Implementation of the new design in the SAG mill was carried out, resulting in increase in daily throughput from 6 to 12%. Further, the time spent in liner change was reduced by 47% given the reduction in the numbers of parts. This operation also benefited from having no stops due to unplanned shutdowns to replace broken tiles. These demonstrate the benefit of coupling advanced computational tools to sound engineering principles in continuous improvement of liners."

Jan 1, 2014

By Hernán Menares, Diego Hernández

"Over the last few years, the copper mining industry has been facing a changing scenario with respect to both the market and society which has resulted in taking a closer look at the way in which mining is being done. The cycle of high metal commodity prices of the last decade left the industry with high costs. Together with increased environmental and social requirements, a decrease in ore body quality, scarcity of resources such as human capital, water and energy, has resulted in an ever-increasing challenge to make a profit out of new ore bodies but also to maintain the current operations in the longer term competitive. The major challenge is to create value for all stakeholders, exploiting ore bodies that nowadays are not considered economically attractive, which applies to both new ore bodies and existing operations, but in a sustainable way. In order to achieve this objective, it is necessary to approach the mining business differently in five main areas: (1) operational efficiency through better use of installed equipment and skilled labor force; (2) efficient use of energy; using opportunities for alternative energy sources and efficient design; (3) efficient use of water; diminishing losses and use of seawater as an alternative source; (4) minimizing environmental impact by eliminating effluents and controlling dust emission; and (5) a more closer, proactive and collaborative relationship with the communities allowing them to be an active player in the solution to assure a sustainable business in the long term. This presentation will show how Antofagasta Minerals is facing these challenges with a long term strategy that includes all of the above mentioned aspects and that is allowing the company to exploit its mineral properties in an efficient and successful way."

Jan 1, 2014

By Xu Wang, Bang Chen, Xiujian Luo, Wei Tang, Xiao’ou Xia, Fangming Liu

"The inertia cone crusher has lots of advantages, such as big crushing ratio, fine particle size, material layer crushing, good passing tramp iron performance and stable technical index, realized open crushing circuit and simplified crushing flowsheet. The crusher was input to China’s Beijing General Research Institute of Mining and Metallurgy (BGRIMM) from Russia’s Mekhanobr-Tekhnika Research & Engineering Corporation at the beginning of the 1990s. This paper introduces that after years of absorption and innovation how Chinese researchers optimized and creatively designed about transmission mechanism, bracing structure, kinetic parameters, lubrication system, dust sealing system, damping system and hydraulic control system etc on the basis of keeping its advanced theory and unique structure, therefore the crusher’s stability was raised and the usage cost was reduced greatly. Accordingly the inertia cone crusher in China has been widely used in many fields, such as mineral resources and the recycling of metallurgical slag. The achievement in cooperation was fully affirmed by governments of Russia and China, and cooperation of science and technology in the mining and metallurgy industry between Russia and China is promoted greatly. INTRODUCTION From the early 1950s, the former Mekhanobr Institite(now Mechanobr-Tekhnika Research & Engineering Corporation) devoted itself to the research of inertial cone crusher and put it into industrial application in the late 1980s. Inertial cone crusher is like a maverick flower in the field of crusher. With its excellent performance and excellent application effect, it shocks the world and is destined to shine with a bright future. In the early 1990s, the chief leaders of the Beijing General Research Institute of Mining and Metallurgy (BGRIMM), Academician Sun Chuan-yao and Professor Zheng Baochen, captured the extraordinary performance and strong vitality of inertial cone crusher with keen eyes. So the two big institutes started the cooperation to introduce inertial cone crusher to China. Since then, Inertia cone crusher has been able to flourish in China and have achieved impressive results with two institutes’ continuous effort."

Jan 1, 2018

By G. J. Feng

Based on detailed theoretical analysis of coarse floatation and three-phase froth, a laboratory system which contains a new type of froth floatation equipment is established. Through water experiment, the relationship among floatation dynamics parameters of the equipment is studied and the best work parameters are educed too. Based on all of above, Slurry test is carried out in a copper concentration plant. Granule between 0.28~0.45mm can be reclaimed successfully. The slurry test proves that to separate coarse minerals in froth floatation equipment is a kind of effective method, it is well worth to make a further study.

Jan 1, 2014

By M. Evertsson, M. Johansson

"In minerals processing control is vital to increasing performance and output of a plant. Model predictive control (MPC) is one of the most effective control strategies used in process industry. Sbárbaro (Sbárbaro and Del Villar, 2010), Asbjörnsson (Asbjörnsson, 2015), and Légaré (Légaré et al., 2016) have for example highlighted the possibility to simulate, develop and tune control systems using plant simulators within minerals processing. In more recent years the use of model predictive controllers have increased, and many process industries now utilize more advanced control methods to regulate their processes, raising the question regarding how to, build, test and verify a proposed control solution successfully. In this research, a linear model predictive controller is formulated and applied to a simulator of an existing tertiary crushing circuit. The circuit has in previous work by Johansson (Johansson, 2017) been modeled in MATLAB Simulink and calibrated relative plant data to an average error of less than 10% over 8 hours of production. The work demonstrates how to formulate the controller model structure to describe conveyor belts, storage components, screens, crushers, and control objectives for a minerals processing circuit. The work illustrates how to apply and successfully evaluate possible upsides in a circuit. The advantage of a crushing circuit simulator is that it can be configured, tuned and modified in any possible way, which is of great benefit to developers and engineers. Additionally, examples of how to use estimated measures to improve the performance of the plant are demonstrated. The control performance is finally evaluated for three different controller configurations."

Jan 1, 2018

By P. Holtzhausen, L. Auret, B. Lindner, A. Haasbroek

"Spiral concentrators offer a cost effective way to separate valuable minerals from gangue by displacing lighter materials to the outside, and heavier materials to the inside of the spiral. The separation can be seen as visible concentrate bands and splitters are set at the bottom of the spiral to effectively split the ore into various densities. As there are typically many spirals in a concentrator plant, it becomes ineffective to continually adjust the splitter positions manually. Vermaak et al. (2008) proposed to use image recognition to detect the concentrate bands, thereafter, creating a model predicting the positions under certain input conditions. This model could then be used for optimisation and/or control of splitter position or band position. In contrast an online concentrate band detection system would provide real time concentrate band positions without losing accuracy due to model generalisation. These systems are usually expensive and time consuming to develop, due to a lot of centralised features required (image capturing, image processing and/or feedback to a controller). This study took advantage of the recently developed Raspberry Pi minicomputer to perform rapid prototyping of an online image processing sensor. The Raspberry Pi, and accompanying camera module, offers a portable Linux environment which can natively run the required image processing algorithms. Furthermore, extensive use of OpenCV was made to reduce development time, by relying on existing and proven algorithms to detect the concentrate bands. The Raspberry Pi also incorporates generic input/output ports which can be used in future work to provide the signal to a controller. In conclusion, the Raspberry Pi was successfully used to perform real time concentrate band position detection on a spiral concentrator. This solution is more general than an experimentally identified input-output model and may be used for control or optimisation studies in a wide array of spiral concentrators."

Jan 1, 2014

By Edson Charikinya, Pierre-Henri Koch

"The extraction of mineral values from ore requires liberation followed by separation steps. Liberation is achieved by size reduction operations which are energy inefficient processes typically dominating the energy consumption in a mineral concentrator. As the grade of ore reserves declines, future viability of mineral operations will be determined by energy costs of comminution. The application of high power microwave energy to secondary crusher products has been suggested as a possible commercially viable thermal treatment method for reducing comminution energy and improving value mineral liberation. Recent studies have shown that microwave pre-treatment of coarse sphalerite ore particles (> 5mm) at specific microwave heating energies (1-3 kWh/t), induces microfractures and creates new crack surfaces. This suggests that subsequent crushing of these microwave treated particles could yield enhanced liberation. However, limited studies have been carried out investigating the mode of breakage and the extent of enhanced liberation in that case. The objective of this study is to develop numerical methods for quantifying the extent of enhanced liberation and mode of breakage in crushed microwave treated and untreated particles. Sphalerite ore particles representing small (-5+4.75) mm, medium (-16+9.5) mm, and large (-25+19) mm HPGR and cone crushed particles were microwave treated at specific energies between 1-3 kWh/t. Cracks in the ore particles before and after microwave treatment were analysed with QEMSCAN and numerical models of the measured particles (before and after microwave treatment) were developed in MATLAB. The propagation of random and non-random cracks was investigated by simulating comminution of the modelled treated and untreated particles. Results of this study demonstrate that the breakage mechanism and the liberation of valuable minerals from gangue in microwave treated and untreated particles is significantly different. This study contributes to the development of numerical tools to quantify crack propagation in heterogeneous ore particles."

Jan 1, 2018

By Yong Liu, Peng Qian, Shu-Feng Ye, Shao-Jun Chu, Pei-Wei Han

"Chromite with a low mass ratio of Cr to Fe (Cr/Fe ratio) was treated by the carbochlorination method using solid chlorinating agent (MgCl2 and CaCl2) and carbon in the present paper. The results showed that iron could be selective removed mainly in the form of FeCl2. The removal of iron was indirectly, which consisted of the decomposition of solid chlorinating agent to release Cl2/HCl and the carbochlorination of FeO•Cr2O3 by Cl2/HCl and C. The Cr/Fe ratio increased as increasing temperature from 700 ? to 900 ? in air atmosphere, while the tendency was opposite in N2 atmosphere. The removal efficiency of iron by CaCl2 was better than that by MgCl2. At last, a new pelletizing process was proposed to treat fine chromite with a low Cr/Fe ratio based on carbochlorination method, which could produce the high quality roasted chromite pellets with higher Cr/Fe ratio and compressive strength. INTRODUCTION Chromite is mainly used for the production of ferrochromium. A high Cr/Fe ratio (>2) of chromite is usually required to meet the technical specification of ferrochromium.(Gasik, 2013) Attentions have been attracted to the economic and efficient methods for the recovery of chromium from lower-grade ores as the higher-grade ores become depleted. However, the Cr/Fe ratio is difficult to improve through the conventional beneficiation methods (such as gravity concentration, flotation) due to the spinel composition, although beneficiation methods could increase the metal content of chromite ores by removing gangues.(Nafziger, 1982) The main industrial mineral of chromite is (Fe,Mg)O•(Cr,Al,Fe)2O3, which belongs to spinel magnetite.(Liu, 2013) Iron should be selectively removed through the structural dissociation of spinel to increase Cr/Fe ratio.(Nafziger, 1982)"

Jan 1, 2018

During incineration of municipal solid waste (MSW), some heavy metals and other environmentally harmful elements are liberated into bottom ash. The stricter environmental regulations require a higher immobilization efficiency of the ash before its safe disposal and application. Vitrification is one of the promising options, and has the advantages of high destruction efficiency of organics, high immobilization of heavy metals, and large volume reduction. The main components of the vitrified slag are SiO2, CaO, Al2O3, Fe2O3, Na2O and MgO, and the compositions have direct effect on the glass formation during vitrification, and further on the physical and mechanical properties of the slag. To provide essential data for the utilization of bottom ash as vitrified slag, the phase relations and thermodynamic properties of the oxide system need to be systematically investigated. In the present study, the liquidus temperature of the typical vitrified bottom ash slag was determined by using differential scanning calorimetry (DSC) measurement. High temperature equilibrium experiments were conducted to investigate the phase relations of the sub oxide system of CaO-SiO2-Na2O by means of Scanning Electron Microscopy (SEM), Electron Microprobe Analysis (EMPA) and X-ray Diffraction (XRD). The results show that the melting temperature of the vitrified bottom ash is around 930°C. In the CaO-SiO2-Na2O system with less than 50 mol% SiO2, the liquidus temperature de-creases with increasing amounts of Na2O along the tie-line of Na2O-Ca3Si2O7. Two compounds Na2Ca3Si2O8 and Na4Ca8Si5O20 are identified in the oxide system.

Jan 1, 2014

By D. M. R. Sekhar

Certain types of rock phosphates of sedimentary origin are applied to acidic soils as fertilizer directly. Recent research in India showed that high grade rock phosphate in fine size when used as a mix with organic manure works as efficiently as di-ammonium phosphate (DAP) in alkaline soils. The rock phosphate from Jhamarkotra, India (sedimentary origin), Egypt (sedimentary origin) and South Africa (volcanic origin) showed good agronomic efficiency when used as Phosphate Rich Organic Manure (PROM). Further PROM shows equal residual effect. The results of efficiency of PROM made using two grades (+ 24% P2O5 and 34% P2O5) of rock phosphate mineral from Jordan show that low grade rock phosphate slimes are as effective as high grade phosphate concentrate when used in PROM. Also PROM is very effective in the saline soil of Eshidiya desert where DAP is not at all effective.

Jan 1, 2014