Search Documents

By T. Laxmi

This paper details the optimization of rougher Wet High Intensity Magnetic Separator (WHIMS) using response surface methodology. The optimization is in parametric form and takes account of the major operating variables in WHIMS operation such as current in ampere and grid gap, in inch. The objective is to recover ilmenite mineral from red sediment deposits of Srikakulam, India by optimizing the rougher WHIMS. We predict mineral recoveries as a function of current and grid gap. Combination of these predictions with assay data provides predictions of mineral grades and recoveries. The optimized response was validated against data derived from laboratory-scale rougher WHIMS test work, comprising (i) mineral grade, (ii) mineral recovery, and (iii) separation efficiency of the process. We observed close match between the experimental and the predicted data over most of the operational range. This paper describes how the optimization was carried out using the response surface methodology along with MATLAB. The response surface was used to closely investigate the separation of ilmenite mineral by varying ampere and grid gap. The results show that under optimum conditions, such as 3.5 amp current (0.53 Tesla) and 2 inch grid gap, the mineral grade could reach, as high as 87.9% in the concentrate with 74.3 % recovery and 74.4% yield. Keywords: red sediment, wet high intensity magnetic separator, optimization, ilmenite, placer heavy minerals

Sep 1, 2012

By Q. Zhang

This paper, by studying the surface properties of pure dolomite minerals separated from representative marine sedimentary rare earth-bearing phosphate ores in Zhijin, Guizhou, aims to study the effect of different anions on the ? potential of dolomite. The research findings showed that the dolomite mineral had a point of zero charge (PZC) at pH 6.5, and the PZC shifted towards lower pH values with addition of anion SiO32- and PO43-. However, addition of anion CO32- and F- resulted in higher PZC values. Keywords: dolomite, ? potential, PZC, anion

Sep 1, 2012

By M. Schneider, J. Regler, Th. Neesse, AKW A. + V GmbH & Co., J. Dueck, F. Donhauser

"In practice the advantages of high-quality hydrocyclone separation are often reduced due to varying feed suspension properties, solids concentrations and particle size distributions. Therefore, a new control system for a battery of hydrocyclones with a nominal diameter of 150 mm was developed for bentonite slurry regeneration associated with tunnel excavation using bentonite slurry as a transport aid and lubricant.As can be seen from Fig. 1, the hydrocyclone battery has been modified for regulation purpose. The battery was manufactured with an overflow collector as a closed pressure chamber (1) with a discharge pipe (2) where the throttling valve (3) was installed.With increased stepwise throttling of the overflow, the volume split is changed with the effect that the solids discharge in the underflow is increased. To stabilize the total throughput, the feed pump speed is simultaneously increased so that the pressure drop ?p across the hydrocyclones (9) remains approximately constant. However, this causes the increasing pressure inside the hydrocyclones, which results in a further intensification of the underflow discharge. After the detection of the break through of the air core (transition state) by the capacitive sensor (4), the throttle valve is shortly opened, and a new regulation interval can start again. The control concept is focused on maintaining the optimum operating state, characterized by the underflow discharge shape at the transition state between rope and umbrella discharge."

Jan 1, 2003

By James D. Bittner

Separation Technologies, LLC (ST) has developed a processing system based on triboelectric charging and electrostatic separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. The environmentally friendly process can eliminate wet processing and required drying of the final material. The process requires little if any pre-treatment of the material other than grinding and operates at high capacity ? up to 40 tonnes per hour by a compact machine. Energy consumption is low, approximately 1 kWh/tonnes of material processed. Since the only potential emission of the process is dust, permitting is typically relatively easy. In contrast to the other available electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the ST belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (500 µm) materials with very high throughputs. The triboelectric particle charging is effective for a wide range of materials and only requires particle ? particle contact. The small gap, high electric field, counter current flow, vigorous particle-particle agitation and self-cleaning action of the belt on the electrodes are the critical features of the ST separator. The high efficiency multi-stage separation through charging / recharging and internal recycle results in far superior separations and is effective on fine materials that cannot be separated at all by the conventional electrostatic techniques. Since 1995, this triboelectric process has been extensively used for the beneficiation of coal fly ash with eighteen separators in place and over 100 machine-years of operation at locations in the North America and Europe. The technology has been also successfully applied to the beneficiation of a variety of minerals including calcium carbonates, talc, and potash.

Sep 1, 2012

By K. Gonçalves

One of Vale?s sponsored research project is aimed at the implementation of a practical scale-up procedure for flotation. In this context, detailed flotation kinetics characterization is of critical importance. This work presents the results of a campaign aimed at characterizing flotation kinetic parameters with respect to particle composition. MLA analysis was carried out for 40 narrow-sized iron ore particles with known flotation time from a controlled flotation kinetic test. The iron ore sample studied (59% hematite and 41% quartz) comes from a mine in the southeast of Brazil and the type of reagents applied are the same as used in the plant. For the reagent conditions tested, the overall rougher concentrate (sink) yielded 79.1%, pure quartz and hematite recoveries to the froth were 56.0% and 4.8%, respectively. The results from the kinetic tests show that the flotation rate of the particles doesn?t vary much (~0.03s-1) with composition and that the fraction of floatable particles in each grade controls the separation action. The results show that the rate of flotation is controlled by transport and that the selectivity is controlled by the fraction of floatable particle of each phase.

Sep 1, 2012

By B. Z. Wu

The ore dressing of tin-polymetallic lean ores is a difficult problem and the research emphasis in domestic nonferrous metals mining field. Through research and tackle key problem,and in order to supply reference in dealing with the same types ores, this paper expatiates the exploiture and appli-cation of six item new technology and technics in ore dressing of tin-polymetallic lean ores. It include the technics of multi-step compounding disposing tailings, grinding step by step, grinding and processing circularly technology, high thickness without circle flotation technology, dispersedly flotation tin step by step technology, exceed fine lean plumbum stibium zinc flocculation flotation technology, the synthetically recovery of waste water after ore dressing technology.

Jan 1, 2014

By L. Y. Zhang

The metallic sulphides in Jinchuan Mine are relative friable and the gangue minerals suffer of wide secondary change, the overgrinding of metallic sulphides and sliming of gangue minerals are the main cause that makes the mineral separation indexes difficult to improve. So changing the process of grinding, and classification, and optimizing the particle size distribution of grinding product is the key improving the separation performance of Jinchuan nickel and copper ore.

Jan 1, 2014

By I. N. Babich

"Complex technological problems associated with the processing of mineral raw materials require the search and development of new means and ways of thinking. At present, computer cognitive graphics (CCG) are one of the most actively developing areas of new information technologies. The aim of the study was to optimize the cycle of technological evaluation of ores at all stages of geological exploration of deposits on the basis of analysis of geological sampling data using CCG. A new approach has been developed that facilitates optimization of the whole cycle of subsoil exploration. At the gold ore deposit, the results of the geological sampling data were processed by the method of constructing the CCG in the form of a histogram showing the frequency of gold extraction and the average amount of its content. Significant peaks of the metal content in the ore, exceeding the level of the average content in the ore by tens of times, have been revealed. Graphical interpretation of the parameters of mineralization reflects the uneven nature of its variability, which indicates the presence of large, rarely occurs of gold in the ore and the need to conduct studies on a sample of ore of greater mass than for ores with tiny gold. On a sample of 50 kg gold-quartz ore studies were carried out on gravity enrichment. The maximum size found in the gold concentrate was 0.07 mm. In the course of integrated tests in a gravity concentrate, gold particles up to 3 mm in size were found, which predetermined the need to include the operation of gravity before flotation. A new approach to subsoil research is protected by a patent (RU 2620823).The technological problems that arise before the researcher associated with the processing of resistant ores require the exploration and development of new means and ways of thinking. New problematic situations on complex mineral and raw materials objects are practically not amenable to resolution by existing methods. Integration of industrial and information technologies is necessary. At present, computer graphics (CG) is one of the most rapidly developing areas of new information technologies. For example, in scientific research, including in fundamental research, the accent from the illustrative function of CG (the visualization of what is already known) is increasingly shifting towards the use of computer cognitive graphics (CCG) tools (Bashlykov, 2016). The function of the CCG is to obtain a new knowledge with the help of a graphic representation - a cognitive image or at least to promote the intellectual process of the logical acquisition of this knowledge. In this study, cognitive images are used to graphically represent the distribution of valuable components in the bowels of the deposit, characterizing the state of mineral-raw materials."

Jan 1, 2018

By O. L. Kachor, A. V. Bogdanov

"In 2015 in the frames of federal special-purpose program «National system of chemical and biosafety of Russian Federation (2009-2014)» Federal State Budget Educational Institution of Higher Education ""Irkutsk National Research Technical University” (further–INRTU) performed works aimed at disposal of accumulated arsenical residues at industrial site of the former Angarsk arsenical plant (AAP) processing arsenious ores from Svirsk town in Irkutsk region. The plant in 1934-1949 produced arsenic trioxide for the defence industry. Prior to starting the works on disposal of industrial pollution focus the total amount of cinders stored on 13 ha of industrial site of AAP was 156 900 tons with 1% average arsenic content. Close to the cinders there were also remains of industrial buildings and process equipment in the amount of 6 600 m3 that contained 150 tons of arsenic. Additional source of pollution at the industrial site of AAP is contaminated soil amounted to 48 000 tons. Proven reserves of gold and silver in the cinders were 6.1 and 47 g/t respectively. In 2015 the source of arsenious pollution was detoxificated according to mineral matrix technology and stored in a special landfill with separate stocking of gold-containing cinder and other arsenious residues. This technology of waste disposal specifies extraction of valuable metals from cinder in future. The similar case is with Vershino-Darasunsky settlement in Trans-Baikal Territory where the abandoned industrial site of the former arsenic plant is located in the central part of the settlement. The concentration of arsenic and valuable components can be compared to the concentration at AAP. Since 2016 the demand for removal of such industrial pollution sources is legislated due to amendments in Federal Law No. 7-FZ on environmental protection. It results in a real possibility to remove such dangerous industrial residues deposits as the one located in Vershino-Darasunsky settlement. INTRODUCTION In the frames of federal special-purpose program «National system of chemical and biosafety of Russian Federation (2009-2014)» as well as the Irkutsk region program “Environment protection in Irkutsk region"" for 2006-2015, INRTU performed the works aiming at disposal of accumulated environmental deprivation–arsenical residues from the former Angarsk arsenic plant (further - AAP) (Figure 1) on processing of arsenopyrite ores of Svirsk town in Irkutsk regionThe plant produced arsenic trioxidein 1934-1949."

Jan 1, 2018

By S. N. Shahcheraghi

Grinding is one of the most important and expensive steps in mineral processing allocating about 70% of the total energy in the plants. Nowadays, for optimizing the energy consumption in these equipments, the rock behavior and its size distribution during the crushing have been normally predicted using selection and breakage functions to be able to optimally model and design grinding circuits. For this purpose, the case of Miduk copper mine in Kerman province, Iran was studied. The samples were taken from primary ball mills feed and were subject to screen analysis to achieve uniform sizes. Then, selection and breakage functions were determined at the different grinding times in laboratorial ball mill. Finally, ore size distribution in different grinding times was estimated using MATLAB software

Sep 1, 2012

By D. B. Mazzinghy, D. C. Rocha, H. B. Miller

"The use of ball mills for fine grinding is an inefficient process and has contributed to the increasing popularity of vertical stirred grinding mills in the minerals industry. Over the last decade, the performance and energy efficiency of stirred milling technology has become a preferred alternative to ball mills for fine and regrinding operations. The difficulty encountered in fine grinding is the increased resistance to comminute small particles when compared to coarse particles. Therefore, increased energy inputs are then necessary to raise the number of stress events in a mill to contribute to the comminution of fine particles. This work discusses the effect of operating conditions on the amount of fines produced and torque readings in a screw type batch laboratory vertical stirred mill. A time-based population balance model (PBM) was used to empirically analyze the performance of a vertical mill and to calculate mill breakage parameters for the different operating conditions tested. The results indicate the possibility of applying population balance model to the vertical stirred mill to predict product size distribution with acceptable accuracy. The obtained breakage function shows that the main breakage mechanism in this vertical stirred mill is by attrition, and that the selection function changes with experimental conditions within the mill. Higher agitator velocities are also seen to promote an increase in the degree of attrition between grinding media hence particle selection and fines generation increase.INTRODUCTION Stirred milling technology has been firmly established in the last 20 years as superior to ball mills for fine and regrinding operations due to its superior energy efficiency (Jankovic, et al., 2006). Stirred mills are now commonly used in many sectors of the mining industry, though they have been used in other industries for many years (Stehr & Schwedes, 1983). This technology has proven to be more energy efficient with greater opportunities for future optimization in both fine and coarse grinding."

Jan 1, 2018

The status quo of ecological rehabilitation in metal mine in China and progress in the technology for ecological rehabilitation are presented, including soil reconstruction, soil improvement, plant selection. The present and future research fields are suggested: basic theory of ecological rehabilitation, operative technology of ecological rehabilitation, new technology application research and ecological rehabilitation plan, management and policy.

Jan 1, 2014

By Mohsen Hashemzadehfini

Nowadays heap leaching has become established as a mineral processing technology for treatment of some low grade minerals such as copper, gold, and zinc, etc. Heap height, particle size, leach reagent consumption, and metal recovery are four important metallurgical parameters in a hydrometallurgical process like heap leaching. This paper investigated the effects of heap height and particle size on copper recovery as well as acid consumption. Three heap heights of 2, 4 and 6 meters and two particle size fractions of less than 25.4 mm and 50.8 mm were selected as variables in the experiments. The research results showed the inverse relation between heap height and copper recovery as well as acid consumption. Under given conditions, the copper recoveries of minus 25.4 mm ore are 78.63%, 66.27% and 52.88% higher than that of minus 50.8 mm samples for the heap heights of 2, 4, and 6 m, respectively. Both copper recovery and acid consumption increase with decreasing particle size. Keywords: heap leaching, heap height, particle size, acid consumption

Sep 1, 2012

By W. H. Cheung

Nickel and cobalt production relies heavily on the processing of nickel laterite ores; these ores contain the majority of known Ni and Co reserves, 80% and 90% ~ 95%, respectively. The Caron process is used to extract Ni and Co metals from low-grade nickel laterite ores (1% Ni and 0.1% Co). It involves selective reduction of NiO and CoO minerals followed by ammoniacal leaching. Despite low metal recoveries, this process continues to be technically and economically reliable and thus commercially important globally. However, keeping the Caron process cost-effective has been a challenge for industries because of increasing economic and environmental pressures. Although studies of the Caron process have been extensive, significant improvements in recoveries of industrial processes have not been forthcoming. Reported industrial metal recovery from high iron content ore is only 80% ~ 85% for Ni and only 40% ~ 45% for Co; recovery is even lower for ores rich in magnesium. The real difficulty here is that there is no complete understanding of and control over the complex series of reactions in the ore and in the leaching solution during processing. Achieving effective metal recoveries from the Caron will require control of the mineral transformations, which affect the activation of minerals by reduction. In this study, the effect of over-reduction was investigated, which superseded the effect of activation by lowering the activity of the minerals and thus metal dissolution. Reduction was carried out in a batch reduction apparatus with 1:1 and 1:2.5 CO/CO2 gas mixtures from temperatures of 500 ~ 700°C and residence times up to 60 minutes. The pre-reduced ores were leached using a standard ammoniacal leaching test. Thermodynamic analysis and possible effects of stable phase field on leaching was examined. The results suggest that control of over reduction effects are directly related to the mineral transformation and reduction conditions.

Jan 1, 2014

With the ambitious target of adding another 2,00,000 MW of power generation by the year 2017 in India the demand for coal is bound to grow. The non-coking coal deposits in India are characterized as high ash and difficult-to-wash coals. Quality improvement by beneficiation is almost mandatory due to MoEF notification to use <34% ash coal for all power plants except those located at pithead. Most of the coal washeries in India are based on wet process, where the coal fines are allowed to settle in thickeners. The coarser particles settle faster leaving the fine particles suspended for longer period. The dispersed fine coal particles contain some surface charge, which leads to the development of electrical repulsion between the particles, and as a result of this, the suspension becomes more stable. In order to destabilize the colloidal suspension, flocculants are usually added, so that the settling rate of the fine particles also increases. These flocculants are of cationic, anionic and non-anionic depending upon the type of charge released when dispersed in water. The flocculants may act partly for charge neutralization and partly for inter particle bridging and electrostatic patch formation. The effectiveness of any type of flocculants depends upon the molecular weight and charge density of the polymer. The paper discusses the settling behavior of non-coking coal fines suspension by using different flocculants. Keywords: floculent, coal fines, sedimentation rate, effluent

Sep 1, 2012

By H. Sarvamangala

Selective separation of alumina, silica, calcite and apatite from hematite was achieved through microbiologically induced flotation and flocculation in presence of bacteria (B.subtilis) and that of hematite from apatite after interaction with yeast (Saccharomyces cerevisiae). Bacterial and yeast metabolites containing extracellular proteins were characterized from mineral-grown cell free extract. Bacteria and yeast can adhere to mineral surfaces and influence subsequent separation of the minerals. Bacteria functioned as a stronger depressant for hematite, while yeast cells depressed apatite at neutral pH. Selective affinity of the bacterial and yeast cells towards the mineral surface was observed through adsorption studies. Extracellular proteins (EP) were isolated from B.subtilis and yeast. The protein profile of the EP of bacterial and yeast cells grown in presence and absence of minerals was studied. This study has demonstrated the utility and amenability of microbially-induced mineral beneficiation of iron ores through bacterial and yeast cells and their metabolic by products.

Sep 1, 2012

By Yimin Zhu

This paper introduces the sixteen mappings and rules of mineral flotation and the subgroup, period etc in periodic table of chemical element to provide mineral flotation workers to refer in theory and practice research. the nine mappings and rules of mineral flotation and the subgroup, period are Saline minerals including the first main groups and collectors of aliphatic acid and aliphatic amines, Minerals including the second main group elements and collector of aliphatic acid, Hydrated ion of the second main group elements and quartz flotation, The floatability of oxidized minerals including the four main group elements, Organic acid including the fifth main group elements and wolframe, tin flotation collectors, The floatability of sulfide minerals including the fifth main group elements, Inorganic compounds including the seventh main group elements and mineral flotation regulator, Oxidized minerals including the forth Subgroup elements and organic flotation agents with phosphorus and arsenic, Oxidized minerals including the fifth subgroup elements and organic floating agents including the fifth main group elements, Minerals including the first subgroup elements and CN-, Sulfide minerals including the second subgroup elements and CN-, The effect of the highest N-valency inorganic acids or salts including p area elements of the third period in mineral flotation, Oxidized minerals including transition elements of the forth period and 3# flocculating agent, The floatability of minerals including elements of the sixth period, Element area of generating compositions and the collecting theory of mineral flotation and so and. Keywords: mineral flotation, periodic table of chemical element, subgroup, period, regulator, coordination chemistry

Sep 1, 2012

By Aidan Giblett, Karen McCaffery, Robert Dunne

"A worldwide decline in competency levels of practicing metallurgists over recent decades has become clearly evident and is a common topic of discussion among senior practitioners and professional associations. The associated impacts on the industry are material and include operational inefficiencies, missed optimisation opportunities and suboptimal new plant designs. There are many contributing factors to this condition. Decrease in competency is particularly evident both in regions where imbalance between supply and demand has led to a general reduction in experience levels for comparable roles over time and in emerging regions where a rapid rise in demand for practitioners has occurred in conjunction with rapid economic development and industrialization. The context, depth and breadth of education curricula and levels vary with location such that solutions to the technical competency dilemma may need to be developed specifically for each region with these influences in mind. Delivering, demonstrating and maintaining competencies are a critical requirement of undergraduate training and ongoing professional development. Other factors such as generational and cultural characteristics and expectations, political influences, role requirements and employment reward and recognition systems all play a critical role in determining if core competencies can be effectively developed, applied and subsequently maintained. This paper reviews factors impacting and some common approaches to competency development. The authors’ experiences in the management of professional development efforts within the global industry are reviewed and a blueprint proposed to address industry requirements in this area."

Jan 1, 2014

By Steven Wright, Sharif Jahanshahi, Shouyi Sun

"While there is a large industry based on recovering platinum group metals (PGM) from complex sulphide ores containing Cu and Ni, there is little information on the thermodynamics of the matte phase formed on smelting the ore and in particular the behaviour of Pt in the matte.The equilibrium between metallic platinum and industrial mattes was studied in a series of experiments where a small quantity of matte (5g) and platinum foil of 150 µm thickness (0.5 g) were equilibrated in magnesia crucibles at 1400°C under conditions where the oxygen and sulphur partial pressures were fixed.The chemical composition of the phases was determined from EDS analysis using a scanning electron microscope. Line scans were initially used to confirm that the foils had attained a uniform composition across their thickness. The composition of the matte was determined from analysis of an area of matte including the small metallic droplets and dendrites.The results of the equilibrium study are presented in terms of how the oxygen and the sulphur pressure affect the distribution of Pt, between the matte and the alloy foil (Lmatte/alloy). Other variables investigated were matte chemistry, i.e., the Fe content and the temperature. The activities of platinum in the mattes were calculated using a regular solution model describing the activity-composition relationship in the alloy."

Jan 1, 2003

By A. Muhammad, A. Abdelaal, M. EL Salmawy

"Energy is vital for economic growth and sustainable development. Greater efforts are being devoted to developing unconventional energy resources such as oil shale as an alternative promising source of oil or solid fuel supplement. The main object of this contribution is to determine the upgrade potential of El-Nakheil oil shale using froth flotation. Samples were prepared by comminution followed by sieving into different size fractions. The flotation behavior of the material and extent of cleaning was studied with respect to nonionic and ionic collectors of anionic and cationic types. It was found that the organic rich portions could not be rendered sufficiently hydrophobic by the used collectors and selectivity towards surfactant was very low."

Jan 1, 2014