Search Documents

By K. Haga

In this study, flotation tests were performed to investigate behavior of enargite and chalcopyrite ores from different sources synthetically mixed for separation of enargite. Flotation parameters including; pH, reagents concentration and type and flotation time were controlled to obtain an enargite concentrate with high As and chalcopyrite concentrate and final tailings with As content below 0.5 mass%. The copper ore bearing enargite mineral contained 5.87 mass% As and 16.50 mass% Cu while the chalcopyrite bearing ore contained 0.32 mass% As and 21.63 mass% Cu. The two ore samples were mixed at 7:3 (enargite: chalcopyrite) by weight ratio to prepare a mixed ore sample with arsenic content at 3.16 mass% and 18.25 mass% Cu for the flotation study. For enargite single ore flotation, the 38?75 µm size fraction showed that over 98% enargite was selectively recovered within 5 min at slurry pH of 4.0 and arsenic content in the final tailings was reduced to 0.22 mass%. In mix ore (enargite+chalcopyrite) flotation, 97% of enargite was first removed at pH 4 followed by chalcopyrite flotation at pH 8, and over 95% recovery was achieved in 15 min flotation time. Arsenic content in the final tailings was reduced to 0.1 mass%.

Sep 1, 2012

By József Faitli, Barnabás Csoke, Károly Solymár, Zoltán Hatvani, Dimitri Papanastassiou

"Grinding has a significant economic impact on ore dressing/processing, therefore the sizing of mills has an outstanding role.In most cases, the sizing of dry or wet mills for ore processing is primarily based on the determination of the Bond grindability index, using the Bond-Kjos-Rowland relations. In several cases, grinding takes place under conditions different from these and the grinding conditions have a great influence on the post-grinding process. This is particularly true for the grinding of bauxites where grinding takes place in alkali, often in higher temperature (up to 100 ºC) in alkali Liquor. So it is necessary to develop a testing method providing a reliable grindability index even under these special circumstances (grinding in alkalis medium at different temperatures) and allowing a more precise mill sizing. The new heated mill is suitable to determine the grindability index under temperature-controlled circumstances, in liquids with different temperatures (water, alkali). This paper presents in detail the equipment, the conditions (parameters) of the testing process for wet and alkaline grinding, the measuring results and the conclusions."

Jan 1, 2003

By Fedotov. K. V., A. Y. Senchenko, V. A. Chanturiya

"The paper describes an efficient process to treat the ore from the largest in Russia copper deposit – Udokan. The recommended process is universally applicable to Udokan ores different in composition and allows reaching high copper recoveries during production of high-grade cathode copper and sulphide concentrate with 45% copper content. There are several promising trends for the process optimization and in the case they are implemented, economics of the whole project could improve significantly. One of the most important optimization options implies reduction of specific energy consumption in the course of comminution operations. Another possible option to optimize the already selected process flowsheet is production of cathode copper from sulphide concentrate directly at a mining and metallurgical plant without sending the latter to other metallurgical works.INTRODUCTIONUdokan copper deposit with resources of more than 20 million tons of copper is the largest in Russia and one of the largest copper deposits in the world. The deposit is located in Kalar District of the Trans-Baikal Territory, 30 km away from Novaya Chara railway station of the Baikal-Amur Mainline.Scientists and engineers from various research institutions have studied Udokan copper ores for years. Along the way, some conceptual process flowsheets have been proposed and each of them has its own pros and cons. The key requirement to the processes being developed was their universal application for processing of all the ore types using a single flowsheet. Due to the hard mining and geological conditions and because of complex material composition of Udokan ores it is of great difficulty to design a process which would provide for maximum economic benefits. That is why the process optimization has been ongoing until now.According to the Russian standards, the main input document for design of a metallurgical plant is referred to as a Process Design Report that covers the following key data sections: analysis of metallurgical testing results, validation of the process, design criteria, process flow diagrams, the mass and metallurgical balances, process description, equipment list and other information necessary for the subsequent design."

Jan 1, 2018

By F. Z. Dong

The paper is mainly about a study on the techniques of separating iron from pyrite cinder of a certain sulfuric acid plant in Shandong province. The main components of the cinder are Fe2O3 and SiO2, and the degree of liberation of iron mineral and gangue is very high. So the iron concentrate with higher degree of iron and lower grade of silicon and sulfur can be achieved by reverse flotation. The iron grade of the concentrate reaches 63% and the recovery of iron is no less than 63%. And the most important influencing factor of the flotation is the temperature of the pulp. A better guideline can be achieved by magnetic separation. The cinder is magnetizing roasted for 15 minutes with temperature of 800?, and the concentrate with the iron grade 64%, sulfur grade 0.2% and iron recovery 85% can be obtained by two stage magnetic separation. A rotary kiln has been built to deal with the pyrite cinder, and the result of the industrial magnetizing experiment and magnetic separation is satisfying.

Jan 1, 2014

Mineral flotation is effective over a relatively narrow particle size range of approximately 10 µm to 150 µm. If the upper particle size limit can be increased, however, a run-of-mine ore may be coarse ground, and only the middlings are ground further to achieve required grades. This will result in significant energy savings and increased throughput. In this communication, methods of increasing the upper particle size limit will be discussed on the basis of a flotation model that can predict flotation from both hydrodynamic and surface chemical parameters. An example of increasing flotation recovery by control of a chemistry parameter is given.

Jan 1, 2014

By N. Acarkan

Beneficiation of the pyrite concentrate of the Kastomonu-Küre (Northern Turkey) copper ore seems to be attractive due to its high Cu, Co, and Zn contents. Pyrite concentrate were used in the experimental studies. Cu, Co, and Zn were recovered from the concentrate by the sulphatizing roasting, leaching and the precipitation using H2S. Sulphatizing roasting experiments were carried out in a rotary furnace and the optimal roasting conditions were found to be at 650°C roasting temperature and 3.0 h roasting period and addition of Na2SO4 of 3 % for the concentrate containing 0.58% Cu, 0.22% Co, and 0.04% Zn. Then, the roasted product was repeatedly leached with 10 g/L H2SO4 solution. Optimal conditions were found to be 60 oC leaching temperature, 2 h leaching period, and 30% pulp density. Leaching efficiencies for Cu and Co were over 99 %. The valuable metals in the pregnant solution were selectively precipitated by H2S as sulfides. Selective precipitation of Cu, Zn, Co was achieved by adjusting the pH and the temperature of the leach solution. Final metal recoveries of 99.20% Cu, 99.40% Co, and 95.60% Zn were attained. The precipitated sulphides are marketable products. Roasting gases with their 15% SO2 content are suitable for the production of H2SO4 and the leach residues can be integrated with the iron ore processing plant as they contain 57.50 % Fe, 17.70% gangue (SiO2, CaO, etc.), 0.04% S, and 0.06% non-ferrous metals.

Jan 1, 2014

By Dave Deglon

The Western Cape Mineral Processing Facility (WCMPF) is a collaborative educational initiative between the Departments of Chemical Engineering of the University of Cape Town, the University of Stellenbosch and the Cape Technikon. The WCMPF was established in 1989 with the aim of improving mineral processing education in the Western Cape. Since its inception the WCMPF has had a number of successes in this area, especially in improving the quality of mineral processing practical training. In addition, the WCMPF has played an important role in promoting liaison and interaction between tertiary educational institutions teaching mineral processing in the Western Cape. Over the past decade the WCMPF has played a key role in the education of over five hundred mineral processing graduates and diplomates. This paper presents an overview of the activities of the WCMPF and attempts to encapsulate the ‘lessons learned’ from over a decade of successful functioning as a collaborative educational initiative in mineral processing.

Jan 1, 2003

To extract the gold from refractory gold concentrate with high sulfur and arsenic, the gold concentrate was catalytically oxidized to expose the gold for cyanide leaching. The effects of reaction temperature, initial nitric acid concentration, reaction time and initial gold concentrate concentration on the conversion rate were studied. The results show that the appropriate conditions for the catalytical oxidation of this gold concentrate are: reaction temperature of 65 oC; initial nitric acid concentration of 25% (wt.); reaction time of 1.5 hours; initial gold concentrate concentration of 10% (wt.). Under such conditions, the conversion rate of gold concentrate is 92%. The solution can be used to prepare nano-iron oxide red pigment. Gases released in the process can be recycled and reused by oxidation absorption. A chemical background of catalytic oxidation is proposed.

Jan 1, 2014

By Rob Morrison, Andrew Scott

"Long before a modern mine commences operations it has already become a wealth of information. After start up, it can generate enormous quantities of data - especially with semi-automated data acquisition by instrumented mine equipment.However, much of this data is of limited use for evaluation of (potential) performance unless it links in some way to the site business model.An underlying reason for this waste of data is that the different cultures, financial, technical, community, environmental, etc, not only have many areas of interest but also have very different conceptual models by which they evaluate performance.It is too ambitious to attempt to bring all of these cultures together - in a single step.However, the success of the Mine to Mill - project has demonstrated that substantial operational value can be added by using a more integrated approach to comminution. The next logical step is to integrate measurement and then to track performance from ore body model to saleable product and waste disposal. From resource to product also represents a path from very sparse, highly variable data to much more detailed measurement and more representative sampling.However, in both cases the data collected is strongly focused on the technical requirements - not on the business model.This paper considers how to define at least some of the key decision points in terms of some case studies.Performance data from many areas might be used to derive simple models which can then be used for forecasting and optimisation of planning."

Jan 1, 2003

By Thenepalli Thriveni, Seong-Young Nam, Nam-Il Um

New modern water treatment technologies required for arsenic removal from waste waters contaminated extensively by various background sources from mining, industrial waste, agricultural waste, painting industry and natural geological bed rock system etc. Arsenic is a widely dispersed element in the earth's crust and exists at an average concentration of approximately 5 mg/kg. Arsenic (As) and heavy metals may be released from the mine wastes to the ground and surface water systems, as well as the geological environment due to their solubility and mobility. This research focuses on the effect of accelerated carbonation process for successful removal of heavy metal arsenic anions from artificial waste water and mining waste waters. This accelerated carbonation process is a simple and novel method with 85 ~ 88% removal efficiency. Carbonation has been studied as a process to further improve immobilization of solidified/stabilized waste and granular waste. After successful removal of arsenic anions from solid mining waste and its potential benefits for producing construction materials. Besides, the industrial and urban management systems are generating bulk solid mining wastes, and most often dumping them in open fields. To prevent the landfilling with mining waste, many efforts are being made for the recycling of different types of mining solid wastes with a view to utilizing them in the production of various construction materials.

Jan 1, 2014

By A. V. Myaskov, V. S. Valavin, K. D’Elia, I. O. Krylov, Vu Van Toan, T. I. Yushina

"The purpose of this research is the development of a technology for processing the concentration tailings of limonite ores at Kamysh-Burun Mining and Processing Complex into an iron- containing product for ROMELT process. In the concentration and metallurgical processing of iron ores, substantial amounts of waste are generated (tailings, slimes, slags, metallurgical dust, etc.) that can be converted into a commercial product if is properly processed. This article presents the results of experimental studies of the feasibility of processing iron- containing tailings of Kamysh-Burun deposit (slimes from Verkhne-Churbash storage facility (VCh sample) and dumped waste of Kamysh-Burun (KB sample)) to obtaining valuable components for further uses. Applying Mossbauer spectroscopy has been shown that the iron minerals in the studied samples are technogenic varieties of iron hydroxides. The most suitable technology is the magnetic roasting process, since iron hydroxides are easily transformed into a magnetic, easily recoverable form. Have been shown the advantages of a two-stage magnetic separation, in a strong field and with polygradient separators. Concentrating this material through magnetic methods makes it possible to increase the iron content to 20-21 %. Magnetic concentration of the deeper layers materials results in iron- containing concentrates with a total iron content of up to 58% whit a phosphorus content of about 2%. Reducing the phosphorus content is possible by blending upper and lower layers of the material at a ratio of 1:1. Thus, it is possible to process the material accumulated in the slime storage facility using the ROMELT process combined with preliminary three-stage magnetic concentration and disposal of tailings with the permissible iron content of less than 5%. Wastes from smelting will be slags suitable for use in construction industry. The Kamysh-Burun material preparation for ROMELT process should be performed applying gravity-washing with separation of the -0.4 mm fraction and additional blending for dephosphorizing the concentrate. The smelting will produce pig iron and slag."

Jan 1, 2018

By Sergey Ulianov, Arkady Senchenko, Alexey Shvets, Arkady Bakotin

"This paper is devoted to ultrafine grinding of processing products. This process allows one to include into operation complex ores which earlier were considered as inefficient and economically inadvisable to treat. Fine dissemination of valuable component often does not allow its liberation via standard grinding in ball mills, and therefore requires modern methods of ultrafine grinding (UFG). An example of successful ultrafine grinding usage is its application for crude flotation concentrates regrinding before cleaner flotation stages. A problem often arises with a commercial copper concentrate production in the course of copper ore flotation. Crude flotation concentrate regrinding in a ball mill does not provide for good liberation of the material before cleaner stages. UFG application allows one to get commercial copper concentrate with copper grade of 20% and higher. Another example of ultrafine grinding application is its usage for highly refractory pyrite product received after gold-lead scavenger flotation of polymetallic ore. Earlier this product treatment was economically inefficient. At current application of ultrafine grinding down to 85% minus 20 µm and subsequent gravity processing it is possible to pass major part of gold (73.4%) into concentrate. The constraining factor for UFG application in processing may be the chemical activation of minerals. In the result of this, flotation selectivity may decrease. Therefore ultrafine grinding application extends the areas of efficient usage of metallurgical processes. New technologies allow increasing the level of valuable metals recovery."

Jan 1, 2014

By P. Fawell, C. Castillo, C. Ihle

"The need to reduce fresh water consumption has pushed many Chilean mining companies to utilize seawater obtained from distant locations. At the same time, increasing amounts of fine particles in copper tailings raise new operational challenges, in particular, the thickening and transport of tailings featuring significant fine fractions, which are predominantly clays. In the present paper, we study the role of salinity – using seawater and NaCl – on the flocculation efficiency of copper sulphide tailings to which kaolinite was added. To mimic the water recovery stage in thickeners, flocculation has been induced in jar tests and the corresponding aggregate size distribution has been estimated from chord length distribution data obtained using a focused beam reflectance measurement (FBRM) probe, at various mean turbulence intensities. Results show that for constant flocculant dosing, a measurable influence of the salt on the resulting aggregation exists. For each case, resulting optimal turbulence levels are also reported, a particularly interesting feature when comparing flocculation efficiency of the coarse and fine fraction. INTRODUCTION The concentration of copper minerals through comminution and flotation is intensive in the use of fresh water. The need to reduce the consumption of fresh water and the environmental standards associated with increasingly demanding mining operations have driven improvements in the techniques of recovering water from tailings. The challenges are even greater when required to treat minerals with high clay contents. In Chile, kaolinite is one of the most important clays to consider due to its abundance in the tailings from many operations. The most common and highest throughput unit operation in the mining industry for the recovery of water from tailings is gravity thickening, with sedimentation of fine particles assisted by flocculation. Flocculation is the process of forming aggregates by contacting the suspended particles with a flocculant. The flocculant is typically a water-soluble synthetic long-chain polymer, where copolymers of acrylamide and sodium acrylate are the most common types used in the Chilean mining industry. The aggregation mechanism includes the following key steps: (1) flocculant distribution through the suspended particles, (2) flocculant adsorption onto particle surfaces, and (3) collisions between particles leading to polymer bridging to form aggregates, but concurrently (4) breakage of aggregates becomes a factor under prolonged shear (Gregory, 1988)."

Jan 1, 2018

By Lucy van de Ruit, Megan Becker, Aubrey Mainza, Jenny Wiese

"UG2 chromitite ore is a complex, highly disseminated platinum ore from the Bushveld Complex in South Africa, with typical platinum group mineral (PGM) grain sizes below 15µm. The introduction of stirred mills to the platinum industry has enabled grinding to finer product sizes, which has improved liberation and recovery of the finely grained PGMs. However, reduction in particle size leads to an increase in chromite entrainment in the flotation concentrate, which has a negative impact on the subsequent smelting process. Factors such as particle size, froth structure, solids concentration and water recovery have all been identified as impacting entrainment, but whether particle shape also has a significant effect is unclear. The purpose of this study was to determine whether the recovery of chromite particles by entrainment during the flotation of UG2 ore is affected by particle morphology. A laboratory vertical stirred mill with inert ceramic media was used for grinding UG2 ore which was then floated in a batch flotation cell. Flotation feed and concentrate samples were analyzed using QEMSCAN to quantify the angularity and aspect ratio distributions of the particles. The stirred mill product was found to have relatively broad aspect ratio and angularity distributions, with the major mineral components (chromite and silicates) having very similar shape characteristics. Analysis of flotation feed and concentrate samples suggested that particle shape does not have a significant effect on chromite entrainment."

Jan 1, 2014

By Teemu Väyrynen, Matti Vilkko, Antti Jaatinen, Pekka Itävuo

"This paper shows that smooth and accurate feed-hopper level control is essential for consistent cone crusher operation. The objective of the paper is to define the best practices for tight control of cone crusher feed-hopper level. The paper discusses the challenges involved in a delay-dominant level control problem (specifically, dead-time-induced performance and stability issues, mass flow disturbances, process and actuator non-linearity) and proposes five corresponding control structures. The performance of the proposed control structure candidates is evaluated in a simulation study and, finally, a full-scale experiment is conducted for the best-performing candidate. The results of this study emphasize the importance of control structure selection. While the most obvious control structures failed to deliver the desired performance, the best result was achieved by using control structures that eliminate the conveyor transport delay (dead-time) from the control loop. In practice, the control loop dead-time can be eliminated by either using an actuator (variable-speed feed conveyor) that is connected directly to the feed-hopper, or by redefining the process boundaries closer to the used actuator (regulate the circuit mass balance instead of feed-hopper level). The presented control structures provide means to achieve a consistent cone crusher performance and size reduction. This facilitates efforts to improve the plant’s performance and increases the plant’s overall stability."

Jan 1, 2014

By Thenepalli Thriveni, Seong-Young Nam, Nam-Il Um, Joobeom Seo

In the present work, we report a novel microstructure of synthesized scalenohedral PCC (precipitated calcium carbonate) without any additives by a simple and ecofriendly carbonation process carried out in a liquid-gas system on the crystal growth of the scalenohedral calcite phase. Especially, the process parameters of Ca(OH)2 concentration and CO2 flow rates were investigated to enhance the sensitivity of the process. The highest average length of the scalenohedral calcite was obtained at pH 6.0, temperature 450C, Ca(OH)2 concentration 0.2M, CO2 flow rate 80mL/min, and total volume 1L. The utilization of flue gas-derived CO2 from coal fired power plants could be a form of carbon capture and storage using carbonation reaction with scalenohedral PCC. Finally, the synthesized scalenohedral PCC was used as a filer for ONP recycling. We demonstrated all these experiemnts at semi pilot plant scale.

Jan 1, 2014

By David Dreisinger

"The leaching of base and precious metal ores and concentrates continues to progress in both laboratory study and industrial application. These developments are being driven by the need to respond to difficult ores and concentrates that are not amenable to conventional treatment. In many cases alternatives are being developed to conventional treatment (e.g. Pyrometallurgy) for technical and economic reasons.In this paper, a brief general review of some new developments in leaching will be followed by a more detailed explanation of three process developments that have either been industrially applied or are expected to be applied in a short time frame. The three processes to be reviewed in detail are the Mt. Gordon Copper Process, the Anglo American Corporation/University of British Columbia Copper Process and the PLATSOL Process. These leaching processes operate at low (90°C), medium (150°C) and high (220°C) temperature and are successful in quickly and completely extracting metal values from ores and concentrates.INTRODUCTIONThe process of leaching is widely used in hydrometallurgy to selectively recover a metal of interest from an ore or a concentrate. Leaching and by extension hydrometallurgy is well established in the recovery of copper (copper heap leach ? SX-EW), nickel (Moa Bay and Caron process), zinc (roast ? leach ? electrowin and zinc pressure leach), gold (cyanidation) and uranium (acid sulfate leach). Of course this success extends to many of the metals found in nature. Recently, the importance of hydrometallurgy appears to be increasing with hydrometallurgy viewed as an attractive alternative to both traditional mineral processing and conventional smelting/converting/refining. This increasing interest has led to intensive study and increasing application. Selected developments include:Copper ? the Mt. Gordon process and new concentrate processes such as INTEC, Activox, CESL, Dynatec, Total Pressure Oxidation, MIM Albion, BioCop, and the AAC/UBC Process.Nickel ? Voisey Bay process for hydrometallurgical treatment of Voisey Bay concentrate, HPAL processing of laterites at Murrin Murrin, Bulong and Cawse, atmospheric leaching of laterites, heap bioleaching of nickel sulfides by Titan Resources (Australia).Zinc ? establishment of zinc leach, solvent extraction and electrowinning technology for treatment of the Skorpion deposit in Namibia, new developments in atmospheric and pressure leaching, the Hydrozinc process.Gold ? development of a number of thiosulfate leaching processes for recovery of gold from refractory carbonaceous ores or concentrates."

Jan 1, 2003

By A. An. Mushketov, A. Al. Mushketov, N. A. Sopina

"INTRIDUCTION At present, more and more metallized raw materials with a metallization degree of not less than 80% are used in the smelting of steel. The main quantity of this raw material is produced in furnaces of mine type. Advantages of this type of raw materials for metallurgical processing are low levels of harmful and slag-forming impurities and a high content of metallic iron. At the same time, the cost of smelting raw materials and obtaining high-quality steels are reduced. In addition to the undoubted merits of metallized raw materials, there are high requirements for the quality of iron concentrates, which are the starting material for metallization: the mass fraction of acidic oxides should not exceed 3%; The mass fraction of iron should not be less than 69%, mass fractions of harmful impurities (phosphorus, arsenic, sulfur, copper, etc.) should not exceed 0.02%. These requirements are dictated by the fact that the recovery of burned pellets is carried out by gas in a solid phase. In this case, the empty rock and harmful impurities from the metal are not separated and sent to the steelmaking unit, increasing the heat consumption for heating and worsening the quality of the steel. The combined production of high-quality concentrate and metallized raw materials requires a large capital outlay from the enterprise, which in the future can be compensated for by increased profit from the sale of more expensive marketable products. At present, in the territory of Russia and the CIS countries Lebedinsky mining-and-processing integrated works is the only enterprise that carries out the entire chain of operations for the production of metallized raw materials, starting with the production of high-quality magnetite concentrate with a mass fraction of iron of 69.5% and ending with the production of a metallized product in the form of hot briquetted gland. JSC «SSGPO» is the largest iron-processing enterprise in Kazakhstan, which processes about 40 million tons of ore per year and receives 16 million tons of concentrate per year with a mass fraction of iron 66.0-66.5%. The technological scheme existing at the concentrator of JSC ""SSGPO"" includes the crushing of the feed ore to the size of 20-0 mm; dry magnetic separation operation; three reduction stages to a fineness of 90-95% kl-0.071 mm; operation of desliming, wet magnetic separation and filtration of the concentrate. Dry magnetic separation of the feed ore makes it possible to remove from the process of 19.6% of the tailings with a mass fraction of the total iron 12.5%, of magnetite 2.2%. The first reduction stage is carried out in rod mills with the volume of 40 m3 to a size of -1.6 + 0.0 mm. The first stage of wet magnetic separation is carried out in counterflow magnetic separators PBM-P-150/200L. The magnetic product of the first stage of WMS is classified in hydrocyclones; sands enter the second reduction stage into central discharge ball mill 3600 × 5000. Runoff of mills enter on the second enrichment stage in counterflow magnetic separators PBM-P-150/200L. The magnetic product enters the classification of the second stage, forming a closed cycle. Mass fraction of the class -0.071 + 0 mm in classifications runoff of the second stage is 70-75%. The second stage classifications runoff is transported toWMS-III operation in semi-counter separators PBM-PP-120/300. The magnetic product of the third stage enters the classification of the third stage. Granular residue are transported to the reduction of the third stage into central discharge ball mill 3600 × 5000. The mill runoff enters the third stage of classification, forming a closed cycle. Classifications runoff of the third stage enters on deslimation. Deslimed product is sent for fine screening to the crasher «Derrick» 2SG48-60W-5STK with a cell size of 0.1 mm. Top size of crasher is sent to regrinding. Undersize with a mass fraction of the class -0.071 + 0 mm 90-95% is fed to the wet magnetic separation of WMS-"

Jan 1, 2018

By Gaurav Soni, Roe-Hoan Yoon

A first principle flotation model has been derived from the basic mechanisms involved in flotation. The model consists of a series of analytical equations for bubble generation, bubble-particle collision, attachment, detachment, and froth phase recovery. The model can predict flotation from both hydrodynamic and surface chemistry parameters such as bubble size, particle size, energy dissipation rate, ?-potentials, contact angles (?), etc. The model predictions have been compared with the results of a series of laboratory flotation tests conducted using mono-sized glass beads of different particle sizes and contact angles under different operating conditions. Some of the experiments were conducted using a 1:9 mixtures if hydrophobic silica and hydrophilic magnetite, so that the product graded could be readily determined by simple magnetic separation. The model predictions are in good agreement with the experimental results both in recovery and grade. A computer simulator developed on the basis of the model is capable of designing a preliminary flotation circuit on the basis of feed characteristics, e.g., size-by-liberation data, and the hydrodynamic information on the flotation cells to be incorporated in the circuit.

Jan 1, 2014

By Alireza Javadi Nooshabadi, Kota Hanumantha Rao

Formation of hydrogen peroxide (H2O2), an oxidizing agent stronger than oxygen, by sulphide minerals during grinding was examined. It was found that pyrite (FeS2), chalcopyrite (CuFeS2), sphalerite ((Zn, Fe) S), and galena (PbS) generated H2O2 in pulp liquid during wet grinding and also when the freshly ground solids are placed in water immediately after dry grinding. Pyrite produced more H2O2 than other minerals and the order of H2O2 production by the minerals was found to be pyrite > chalcopyrite > sphalerite > galena. The pH of the water influenced the extent of hydrogen peroxide formation with greater amounts of H2O2 produced at highly acidic pH. Furthermore, the effect of mixed sulphide minerals, i.e., pyrite-chalcopyrite, pyrite-galena, chalcopyrite-galena and sphalerite-pyrite, sphalerite-chalcopyrite and sphalerite-galena on the formation of H2O2 showed increasing H2O2 formation with increasing pyrite fraction. There is clear correlation of the amount of H2O2 production with the rest potential of the sulphide minerals; the greater the rest potential of a mineral the greater the formation of H2O2. This study highlights the necessity of revisiting the electrochemical and/or galvanic interactions between sulphide minerals, and interaction mechanisms between pyrite and other sulphide minerals in terms of their flotation behavior in the context of inevitable H2O2 existence in the pulp liquid.

Jan 1, 2014