Search Documents

By Markus A. Reuter, Bernardete Castro, Antoinette van Schaik, Han Remmerswaal

This paper describes the inseparable relation between product design, liberation, and metallurgical recovery in the optimisation of the recycling of passenger vehicles. This is illustrated by the use of an optimisation model that uses among others a material combination matrix based on metallurgical process data, which depicts the consequences of the quality of intermediate recycling products on the metallurgical material recovery and final alloy metal quality. Various simulations will illustrate the effect of changes in product design and hence liberation on the recycling of end-of-life vehicles. Although this paper focuses on cars, the discussion is equally valid for any end-of-life product. Calibration of the model will be discussed with reference to experiments carried out in order to study the optimal recovery of aluminium applications used in passenger vehicles.

Jan 1, 2003

By Y. Q. Yang

Jig is a kind of conventional and old gravity concentration equipment, which is mainly used in the preconcentration of medium particle fractions of low-grade nonferrous metal ore. In the past ten years, studies on jigs have made a great progress on separation of coarse and fine particle fractions. At the same time, pneumatic jigs have been widely used in processing of nonferrous metal ore. In this paper, pilot test study and commercial operation for several kinds of jigs used in Dachang con-centrator has been introduced. Dachang mining area of GuangXi province is rich in mineral resources, where many minerals exhibit various complex properties. Many elements such as Sn, Pb, Sb, Zn, S, As, Cu, In, Ag, Gd, Ag, Ga, etc, were found in the run-of-mine ore (ROM). At present, Dachang concentrator produces tin concentrate, lead-antimony concentrate and zinc concentrate. Other valuable elements get enriched and recovered in above concentrates. Dachang Mine with a mining operation history more than sixty years will end its mission on the rich ore resource exploitation. At present, low grade ores are porcessed in the concentrator, and the concentrator begins to run at a loss upon processing the low-grade and refractory ore. Heavy medium cyclones were used in the concentrator for processing 20-4mm fraction, Gongge jigs for 4-2mm fraction, and cone concentrator combined with spiral concentrator to discard the tailings of -2mm fractions. In order to minimize overgrinding, table flotation was used to recover some liberated cassiterites in a complex processing technology. Therefore, the concentrator is difficult to manage. Many years studies have shown that heavy medium cyclones and spiral concentra-tors can be replaced by sawtooth shaped wave jigs to discard 50% tailings to improve the grade of feed. And the feed was divided into rich one and poor one to minimize overgrinding of valuable cassiterites with different grinding mills. In this case, the recovery of the valuable minerals can get improved and the flowsheet was simplified. Moreover, the concentrator begins to make profit with reduction of cost. At the same time, pollution in the concentrator gets reduced and the working condition gets improved too. Sawtooth shaped wave jig was used in Changpo concentrator for replacement of cone separators and spiral concentrators to discard the tailings of -4mm fraction, and the yield of discarded tailings got improved from 30% to 50%. Grades of tin, lead and zinc in the tailings are lowered from 0.15%, 0.12%, 0.7% to 0.06%, 0.05%, 0.4% respectively, with a loss reduction of tin, lead and zinc from11%, 9%, 10% to 7.5%, 6%, 5% respectively, corresponding to the increasement of recovery of tin, lead, zinc from 52%, 50%, 55% to 56%, 56%, 62% respectively. Cost of the concentrator for processing one-ton ROM was therefore dropped from RMB155.28 to RMB119.74. Changpo concentrator lost RMB2.5 million in 2003, but it made a profit of RMB0.92 million in 2006 after the innovations. Batac jig was used in Tongkeng concentrator to discard the coarse tailings at 20-4mm, with a discarded yield of 35%, and the grades of valuable minerals got improved with a recovery above 95% for tin, lead-antimony and zinc.

Jan 1, 2014

By V. A. Chanturiya

The results study the minerals oxidation were obtained by us during the methods of microscopic, FT-IR spectroscopic, XRD and chemical analyses of sulphides in tailings of copper-nickel wastes in Kola peninsula. Sulphide minerals begin to oxidize already at the stage of stockpiling and initial stages of storing. The proportion of non-ferrous metals and magnesium oxide increases with time, calcium partially precipitating in the form of gypsum. Comparison of heavy metal contents in pore solutions in cur-rent and stale copper-nickel ore concentration tailings has revealed a significant difference in practically all the parameters. The lower metal contents in current tailing pore solutions (by 5~30 times) are probably due to the presence of float reagent residues blocking oxidation. Much lower concentrations of magnesium and calcium can be accounted for by the difference in kinetics: the rate of sulphide oxidation at this stage is much higher than that of solution interaction with non-metallic minerals as the result of which the solid phase ? solution equilibrium is not achieved. It is generally believed worldwide that it the mining wastes with acidic pore solutions that pose the greatest hazard for the environment. Our findings suggest that although the solution pH in all the samples is higher than 7.8, the contain heavy metal concentrations by far exceeding permissible values. The direct determination of the total and silicate Ni contents in the tailings from current production and in storage tailings has shown that both sulphide and silicate Ni forms occur in tailings. However, the role of silicate Ni is much larger in the storage tailings. The average silicate Ni content accounts for 10% of the bulk Ni content in the current tailings and it increases to 40% in the storage tailings. Thus, the storage tailings are marked not only by sulphide oxidation and the removal of water-soluble sulfates, but also by the interaction of sulfates with the silicate matrix. Although complete equilibrium is not achieved even within 30 yr under polar-region conditions, the major part of the Ni in fine-grained fractions passes into silicate form. The probability of Ni transition to the silicate form directly correlates with the dispersion of the material and the amount of chemically reactive serpentine and hydrochlorite. The migration of Ni as sulfates and its precipitation by chemically active silicates distorts the distribution of this component in the coarse- and fine-grained fractions that are typical of tailings from the current production of copper-nickel ores. On the one hand, the variation of the mode of Ni occurrence in storage tailings lowers the value of technogenic raw materials as a source of this metal.

Jan 1, 2014

With rapid development of Chinese iron & steel industry, it is of significance to intensify the utilization of domestic complex iron ore resources. The tin, zinc-bearing complex iron ores are typical polymetallic and intractable ones because of the complicated intergrowth relations among the multi-elements, and they have not been efficiently utilized, presently. Based on the thermodynamic analysis of iron, tin and zinc oxides reduction by CO, the technological conditions of tin and zinc recovery and pellets preparation from tin, zinc-containing iron concentrates by selective reduction roasting are studied and a new comprehensive utilization process is developed in this investigation. Under the optimum conditions, the tin and zinc volatilization is respectively in excess of 80% and 70%, and the compression strength of roasted pellet is more than 2500 N/P. Moreover, the residual tin and zinc in the finished pellets is below 0.06%. The finished pellets can be used as high quality iron-making burdens for large-scale blast furnace.

Jan 1, 2014

By G. C. Li

Gold extraction using iodide leaching from refractory carbonaceous gold ores was studied. Thermodynamic analysis of iodide leaching chemistry had been carried out. Eh-pH diagram of Au-I2-I--H2O leaching system showed that the coordinating active forms from iodides were I3- and I-, while the major coordinate compound formed during iodide leaching was AuI-. For leaching parameters optimization, technological parameters such as I2 concentration, I2 :I- ratio, oxidation assisting agents, liquid/solid ratio, and leaching duration were studied. The leaching results showed that the average Au leaching rate reached 91% and 92% for oxidized ore and roasted primary ore respectively. Leaching process proceeded in weekly acidic or neutral slurry at ambient temperature; the leaching duration was 4 hours. After that gold was extracted from the pregnant liquor by activated carbon adsorption ? desorption ? electrowinning process. Gold recovery was over 93% in the adsorption process, while the gold recovery in electrowinning process was about 95%, provided that the initial gold concentration is 40mg/L or larger. For iodine regeneration it is enough to add hydrogen peroxide in excess into the filtrate after gold electrowinning, all the iodides existing in the solution in any forms would be precipitated in the form of elemental iodine.

Jan 1, 2014

By Sushanta Majumder

The physico-chemical characteristics of raw materials used for the production of iron ore pellets have a strong influence on the productivity of pelletization operations and on the quality of pellets. Since iron ores from different sources are used for making iron ore pellets and since the quality of the ores varies with time, there is a need to optimize and control pellet plant operations on a regular basis to achieve optimum productivity while maintaining pellet quality within the desirable specifications. In order to achieve this objective, a model-based on-line optimization system was implemented on two industrial scale induration furnaces. The optimization system consists of a rigorous mathematical model of the induration process, a model for the permeability of the bed of pellets, a statistical model for the quality of iron ore pellets and an optimization module based on sequential quadratic programming. The rigorous model is tested on-line using the wind-box temperature available real-time. The process was optimized to enhance induration furnace productivity for the given constraints on pellet quality parameters such as the cold compressive strength (CCS) and Tumble Index (TI), and other equipment design parameters. Process variables such as induration machine speed, cold air flow rate and hood temperature profile were used as the optimization variables. The on-line optimization system was successfully implemented in two industrial induration furnaces and lead to enhanced productivity. Details of the on-line optimization system and results of process optimization will be presented.

Sep 1, 2012

By A. Pirson, J. Souza, A. Araujo, M. Barbosa, F. Guimarães, J. Lima

"Although a large number of processes have been developed and applied to the separation of barite from other minerals, there is a lack of information in the literature about the separation of barite from iron ores. Nowadays, there are millions of tonnes of iron ore disposed as a waste or tailings given its high content of sulphur in the form of barite. In order to effectively separate barite from iron ore and ensure that mining business is truly creating economic and sustainable values, this paper provides a greater understanding of barite properties, the origin and occurrence of this barium-bearing mineral, and the employed beneficiation processes. A test work is conducted in a barite bearing iron ore from a deposit located in the Republika Srpska (Bosnia and Herzegovina) in order to separate the barite and check if a marketable by-product can be produced by drawing upon rich barite tailings. INTRODUCTION The exploration of iron ore containing barite results in a large amount of unrecovered material. The main difficulty in processing and using barite bearing iron ores is given by their high content of sulphur, silica and barium, which are unwanted chemical compounds in the subsequent processes in iron industry. As a result, millions of tonnes of iron ore are discarded every year into tailings or as a waste, which results in production losses, higher operation costs and environmental impacts (Praes et al. 2013). Therefore, the separation of barite from iron ores not only means reducing the environmental impact, but also an opportunity to generate income and beneficiate society. The beneficiation of barite bearing iron ores is a subject which requires a deeper investigation to solve the challenges faced by the iron industry. There are only a few studies that describe flowsheets proposed for the production of barite concentrate of iron ores. The most likely reason for this gap is that barite is frequently exploited commercially as a primary product rather than a by-product. In order to effectively separate barite from iron ore and ensure that mining business is truly creating economic and sustainable values, this paper provides a greater understanding of barite properties, the origin and occurrence of this barium-bearing mineral, and the employed beneficiation processes. A test work is conducted in a barite bearing iron ore from a deposit located in the Republika Srpska (Bosnia and Herzegovina) in order to separate the barite and verify if a marketable by-product can be produced by drawing upon rich barite tailings."

Jan 1, 2018

By S. Chuanyao

In last decade, along with its booming Chinese economy, China?s higher education has experienced rapid growth. In 2010, the number of various colleges totals more than 3500, with 2.2 million faculties registered. Currently there are almost 30 million students studying in the colleges, 3 times more than 10 years ago. Mineral Processing was initiated in 1949 as a sub-discipline of Mining Engineering, one of the 13 first level disciplines. Mineral Processing is now established in 34 Chinese colleges, recruiting 2600 undergraduate students, 540 postgraduate students and 100 PhD students every year. A further 9 institutes offer postgraduate education in this field. More than 3000 graduates majoring in Mineral Processing join the industry or institutions each year. The four-year undergraduate teaching and practical training in the colleges is designed to produce qualified mineral processing professionals. This includes courses in mathematics and natural science, fundamental engineering and basic and specialization courses. Recently, the ?Excellent Engineer Program? was launched to strengthen students? practical capabilities. This is a 3+1 teaching and training model; 3 years of theoretical course study plus 1 accumulated year of various practical studies, either inside or outside the college. As for graduate employment, mining-related major graduates have been in a good demand thanks to the intensive investment in mineral sector by Chinese companies. The shortage of experienced metallurgists generates a greater than 90% employment rate for Mineral Processing graduates. However, the biggest problem we are still facing is the gap between the quality of the graduates and the requirements of industry, as a result of occupation attraction, teaching systems, faculty quality, and so forth. Another problem is international orientation. Although nowadays Chinese-foreign cooperation in college education is popular, collaborative mineral related projects are far less common, leaving much room for improvement. Looking ahead to the next 10 years, we still have the right reasons to estimate continued prosperity in the minerals sector as well as mineral processing education in China. A brief analysis and views on this will also be shared in the presentation. Keywords: China, mining engineering curriculum, excellent engineer program

Sep 1, 2012

By Sepideh Javanshir

The process of liquid?liquid extraction of gold from chloride solution is complicated by the presence of many variables acting simultaneously in an unknown non-linear fashion for the determination of the final extraction efficiency. In practice, it is quite difficult to develop a model for predicting various properties of such process. Therefore, an alternative approach based on Artificial Neural Network (ANN) is considered to assist in the simulation process. Artificial neural networks (ANN) are powerful tools that can be used to model and investigate various highly complex and non-linear phenomena. This paper presents application of Multi-Layer Perceptions (MLP) to construct relationship that will be employed to develop a quantitative method for the estimation of the extraction efficiency as a function of hydrodynamical parameters such as stirrer speed, [AuCl4]- and DBC concentration, organic and aqueous flow rate. The model is shown to be in excellent agreement with the experimental data (R2 value for training and testing data was 0.9992 and 0.9915 respectively). Therefore, it can be used to optimize the parameters of liquid?liquid gold extraction with dibutyl carbitol (DBC).

Sep 1, 2012

By N. Acarkan

Slags usually contain some quantity of valuable metals. They are actually a secondary resource of metals, rather than an end-waste and have been utilized as a resource material in many areas. In addition, for some applications, slags have comparable or even better properties than their competitors. Leaching is a method for extraction of metals from copper slags. The extraction of metals such as copper and cobalt from the copper slag of Küre-Turkey, was investigated in the past decades. Fayalitic type of these copper slags containing 0.934 % Cu, 0.353 % Co and 50.91% Fe were subjected to the experimental study. As a result of mineralogical analysis of the slag sample, fayalitic type of slag was found to contain hercynite, magnetite, hematite, pyrite, chalcopyrite, covellite, bornite and metallic copper. Direct acid leaching methods were applied on the sample. Effects of leaching time, temperature and acid concentration on Cu and Co leaching recoveries were investigated in the direct acid leaching. The optimum leaching conditions were found as leaching time of 2 hours, solid/liquid ratio of 1/3, H2SO4 concentration of 125 g/L and temperature of 70 °C. At these conditions, 75.5 % of Cu, 95.6 % of Co and 70.9 % Fe were extracted. In the second stage of the leaching experiments, copper in the pregnant solution was precipitated by cementation to produce a Cu concentrate assaying 95.58 % Cu; cobalt was obtained by precipitation with H2S to produce a concentrate containing 62.10 % Co. As a result of this study a process flow sheet has been developed for recovering Cu and Co from these slags to demonstrate its economic and technological benefits.

Jan 1, 2014

By Cheng Wei

Fly-ash was used as adsorbent to remove butyl xanthate from aqueous solution in this study. Adsorption kinetics investigation reveals that the adsorption process abides by the Lagergren-second-order Kinetic Model, and fine fly-ash prepared by grinding has a higher second-order adsorption rate as 1.25 g/mg?min and a higher saturated adsorption amount as 10.92mg/g. Four influencing factors as adsorption temperature, solution pH, consumption of fly-ash and adsorption time were investigated. Testing results indicate that butyl xanthate removal rates declines slightly with the temperature increase within the range of 15-50?, increases slightly when pH rises from 7.27 to 8.01 and then declines from 99.65% to 98.25% when pH rises from 8.01 to 11.10. An enhancement of removal rates can be observed by increasing the consumption of the adsorbing agent or prolonging the adsorption time. Thermal desorption was adopted to regenerate the used fly-ash, and test results show that fly-ash possess good regeneration performance and could be used as adsorbent repeatedly with little influence on the adsorption capacity.

Sep 1, 2012

By O. Jerez, A. Novoselov, L. Gutiérrez, J. Morales, U. Kelm

"In Chile, the evaluation to reprocess tailings for elements other than the traditional Cu, Mo, Au, and Ag, as well as projects to implement long-term monitoring of mining residue sites are key elements of the government’s roadmap laid out for the mining industry for the next two decades. Characterization routines for tailings and mining residues in general have to be adapted from traditional ore and gangue mineral and micro-chemical studies. This contribution summarizes key aspects for the regional mining industry for a basic characterization of tailings with emphasis on small- to medium-size operations with limited in-house facilities and funds to carry out extensive characterization programs. The oldest tailings in Chile were deposited almost a century ago; this fact gives importance to the recovery of past ore /gangue feed information, process circuits and changes (e.g. acid to alkaline flotation), process water provenance and recovery, meteorological registers, and routines of filling a tailings impoundment. Basic characterization should include X-ray fluorescence spectrometry combined with laser diffraction (LD) granulometry followed by X-ray diffraction (XRD), optical microscopy (OM) and automated mineral analysis (AMA) on a reduced set of samples identified by hierarchical cluster analysis. For this detailed stage, only coarse tailings are recommended for direct a study by microscopy and automated mineralogy (P80 >100 µm); for fine tailings (P80 ~30 µm) a combination of XRD and deposit type adapted sequential extraction are more informative options. In particular, for XRD of clay phases, losses of crystallinity may result in deviation of spectra from standard reference phases due to prolonged storage. To monitor surface alteration, scanning electron microscopy can be complemented by Raman spectroscopy to detect residual reagents on mineral surfaces. For reactivity modeling BET measurements are essential."

Jan 1, 2018

Low-grade ore bodies, increase in rock competency, finely disseminated valuable minerals in the ore bodies, ore variability and water scarcity are among the technical challenges faced by the mining industry. These challenges have increased the business risk, capital investment and operating cost of the mining projects. Since the last 20 years, many large-scale concentrators have been built to cope with the above-mentioned challenges. Comminution, especially the fine grinding is an energy-intensive process. For example, the ball mill has a limitation in the fine grinding regime where the energy consumption increases exponentially when the product size is below 45 µm. The industry has been seeking for solutions that have a minimum risk and total cost of ownership. The stirred milling technology such as the TowerMill is well accepted by the industry as it has demonstrated the attributes required for fine grinding. TowerMill is a matured technology that has been adopted since the 80s for regrinding duty. Recently, this technology was installed in secondary and tertiary grinding duty to prepare a finer feed to rougher flotation. Four units of TowerMills were installed in a magnetite concentrator in Western Australia in tertiary grinding duty. Recently, Nippon Eirich has conducted process performance evaluation on the TowerMill circuit. The outcome of the exercise had indicated that the circuit is consuming 3.4 kWh/t to reduce from 55 µm to 35 µm with a narrow product size distribution. The effect of operating variables such as the specific energy, grinding media size, mill content % solids and mill feed configuration on the grinding efficiency were evaluated at the plant scale. Furthermore, the scale-up methodology was validated. The scope of this paper includes the performances of TowerMill and the validation of scale-up methodology.

Jan 1, 2018

By Guanghua Ai, Xiong Huang, Huashan Yan, Ting Li, Tingsheng Qiu

"Cyanide tailings of gold and silver concentrates contain considerable quantities of copper-lead-zinc sulfide minerals that can be recovered. However, the strong inhibition effect of cyanide often makes it difficult to recover these sulfide minerals effectively. In this research, a sample of cyanide tailings was investigated based on the principles of process mineralogy; activating flotation tests were carried out for the target minerals in the tailings, and the activation mechanism of the activator and its influence on the target minerals were investigated by Fourier transform infrared spectroscopy (FTIR). Mixed flotation of copper and zinc was carried out using QJ-01, a combined agent containing sulfite, as the activator of copper and zinc minerals, and ammonium dibutyl dithiophosphate (ADD) and butyl xanthate (BX) as the combined collector. Copper concentrate was obtained from the mixed concentrate by using a combined inhibitor of sodium sulfide and zinc sulfate to inhibit the zinc mineral. Zinc concentrate was extracted from the copper tailings by using copper sulfate as the activator and BX as the collector. The flotation test yielded copper concentrate with a grade of 22.56% and recovery of 76.96%, and zinc concentrate with a grade of 42.56% and recovery of 82.29%, which shows that comprehensive recovery of the sulfide minerals – copper and zinc –from the cyanide tailings was realized. The FTIR analysis showed that CN- was chemisorbed on the surface of chalcopyrite and sphalerite following cyanide treatment, while the combined activator QJ-01 containing sulfite reduced CN- into SCN- and weakened the complexing ability of CN- with metal ions on the mineral surface, thus achieving a good activation effect on chalcopyrite and sphalerite. The results of this study can provide practical guidance in increasing the resource utilization ratio of cyanide tailings in gold mines, and thus contribute to alleviating environmental problems caused by stockpiling cyanide tailings. INTRODUCTION Cyanidation, the most widely used technology for extraction of gold, has several advantages such as high recovery, process maturity, low cost, etc. According to available data, the annual discharge of cyanide tailings from China's gold mines exceeds 20 million tons (Li et al., 2011). Lower grades of exploitable gold ore entail increased discharge of cyanide tailings. Huge quantities of cyanide tailings are regarded as waste and stored, resulting in significant wastage of land resources. Moreover, residual beneficiation reagents, cyanide ions, and heavy metal ions in cyanide tailings cause severe pollution of water and land (Laitos et al., 2013; Donato et al., 2007; Mudder and Botz, 2004). In addition, cyanide tailings often contain valuable elements such as gold, silver, copper, lead, zinc, sulfur, and iron, which, if not recycled, would result in considerable wastage of resources. Hence, it is imperative to study the reduction and safety of cyanide tailings, and the mineral resources present in them."

Jan 1, 2018

By Shuoshi Lu

The Cu-Co ore studied here belongs to the oxide type. The oxidation rates of copper and cobalt are69.30% and 78.78%, respectively. The content of Cu in ROM is 1.34% and that of Co is 0.096%. The ore contains 4.64% carbon.Based on the process mineralogy and previous metallurgy tests, the principalprocess flow-sheet of ?grinding fines 80% -0.074mm, sulphide flotation followed by oxide flotation, and flash flotation for oxides? has been determined.The handling of carbon is determined through tests. The depressant PNL-1 depressed carbon effectively, improved the recovery of sulphide minerals and reduced the reagents consumption.The operation of the flow-sheet was also changed to better at the same time. Keywords: Cu-Co oxide ore, process mineralogy, carbon depression, efficient depressant of carbon

Sep 1, 2012

The effect of the acid anion on chalcopyrite (CuFeS2) leaching has been examined, under care-fully controlled conditions, in a range of acids in stirred reactors and columns at pH 1. Solution speciation calculations were performed to determine possible rate controlling species. The relative leach rates of Cu from chalcopyrite can be explained quantitatively entirely on the basis of solution speciation without the need to invoke any rational relating to surface structure/speciation. The rate of Cu release is first order with respect to Fe3+ activity. The stirred batch reactor experiments at fixed pH 1, Eh of 750 mV (SHE) and 75? showed that chalcopyrite leach rates were rapid in both HClO4 and H2SO4 with 100 % Cu recovery after 73h and 97 h respectively. However, the leach rate in H2SO4 was slower as compared to the HClO4 leach due to a slower increase in the activity of Fe3+ due to the formation of FeSO4-. The presence of Cl- in the leaches (HCl and H2SO4 with NaCl added) led to a low activity of Fe3+, due to the high activity of FeCl2+, resulting in very low leach rates. For the column leach experiments dissolution of Fe and Cu from the pH 1 HCl eluted chalcopy-rite column with quartz proceeded at several times the rate of any other column (chalcopyrite with and without quartz and/or pyrite leached with H2SO4, HClO4, HCl). Three observations indicate that galvanic interactions are not leach rate controlling role: a) The rate of leaching was not uniformly increased for the non-quartz containing columns where the two sulfide minerals, chalcopyrite and pyrite, are in physical contact as compared to the analogous quartz containing columns where they are not; b) there exists a reasonable correlation between the rate of Cu release and the effluent Fe3+ activity for all columns thus indicating that the leach rate is determined by solution speciation; and c) in all cases the proportion of Fe to Cu leached indicates preferential dissolution of Cu over Fe. However, the proportion of Fe to Cu is either the same or greater than expected on the basis of the single mineral columns. This indicates that chalcopyrite is not dissolving preferentially to pyrite.

Jan 1, 2014

By V. P. Yakushkin, B. S. Ksenofontov

"Multistage model designed and used for more detailed description of floatation process. The study develops a new model of flotation kinetics description. It defines flotation as process that consists of several stages: air bubbles and particles are separate, air bubbles and particles form a raising aggregate, aggregate raises to froth layer. This description significantly differs from commonly used model, which is much simplified. The multistage model gives an in-depth description and considers different aspects of flotation. Experimental approval of the new model resulted in its accuracy.The model is to be used for description of all flotation processes’ kinetics of wastewater treatment. It helps in accurate designing of flotation treatment plants and may be used for further research of flotation process. Columnar flotation installation was designed by using multistage model. This installation consists of new tubular aerators with special ejectors, froth pressing system as well as unit of thin-layering lighting to catch microflotocomplex “particle – bubble”. Usage of tubular aerators allowed to aerate the overall volume of pulp. Due to use of special ejectors with longer mixing camera we state higher volume of small-sized floto-active bubbles. Use of multistage model allowed to optimize and get higher technological results of potash salts enrichment. Tests were conducted on centrifuges-floatation installation system. Meanwhile, froth concentrate contained mainly thin hydrophobic particles sized circa 0,1 mm. As a result we set that during floatation cleaning process of froth concentrate 95-98% of chloride potassium (KCI) is derived from foam.The final product satisfies production quality. Columnar floatation installation productivity was 17 – 21 m3/m2h, which is a high technological result. Columnar floatation installation is one of the best examples of concentrating equipment using nearly all technological indices."

Jan 1, 2018

By K. Saberyan

In this study the extraction of zirconium and hafnium has been investigated by solvent extraction using Cyanex 302 in various media such as nitric, sulfuric and hydrochloric acid has been investigated. Effect of various parameters such as type and acid concentration, extractant concentration, type of diluent, equilibrium time, various foreign ions and finally type and concentration of strip-ping agent have been studied. The results showed that nitric acid was optimum media for extraction of zirconium and hafnium. The extraction of zirconium and hafnium occurred quantitatively in the concentration of higher than 4 M nitric acid but in hydrochloric acid media, quantitative extraction obtains over 8 M HCl. In sulfuric acid media, extraction of zirconium and hafnium is negligible. Stripping studies showed that the optimum reagent for stripping was 0.5M sulfuric acid.

Jan 1, 2014

By Kyoungkeun Yoo

A citric acid leaching test after heavy medium separation process was performed to remove the heavy metal contaminat such as Pb, Cu, and Zn from contaminated soil. The lead component was removed from soil by heavy medium separation whereas zinc component shows 0 % - 37.9 % removal ratio with particle size. The citric acid leaching was conducted to remove the remained zinc component. The removal ratio of Zn reached to more than 95 % under the conditions; 10 % in pulp density, 200 rpm in agitation speed, 50 °C, 2 mol/L in citric acid concentration at 2 hrs in leaching time. These results suggest that the heavy medium separation method followed by citric acid leaching is effective for treatment of soil contaminated with various chemical forms of heavy metal. Keywords: metal contaminated soil, citrate, heavy medium separation, zinc

Sep 1, 2012

By S. Castro, L. Gutierrez

"Mining operations are often located in remote arid environments with limited access to fresh water. Shortage of fresh water in such cases makes it necessary to use seawater in mineral processing plants. Such plants treating Cu- Mo sulfide ores in seawater have been fully operational in Chile (e.g. Las Luces, Centinela). In many cases process waters used in commercial flotation plants (e.g. Mt Keith in Western Australia) are even more concentrated electrolyte solutions than seawater. This paper is an attempt at classification of the flotation operations carried out in process waters that are concentrated electrolyte solutions.INTRODUCTIONAccording to Gleick (1966), of the total Earth’ water resources 97.5% is in the oceans and ice caps, and thus only about 2.5% is fresh water. Shortage of fresh water in many parts of the world makes it necessary to use seawater in mineral processing operations. The existing commercial operations using seawater as well as recent research projects that deal not only with sulfide ores but also with apatite ores provide a lot of information that can now be generalized. The progress that has been made in this area is reviewed and based on this information an attempt is being made at classifying the flotation operations carried out in highly concentrated electrolyte process waters.SALT FLOTATIONFlotation in highly concentrated electrolyte solutions was studied by Klassen (Klassen, 1963). He reported that hydrophobic, bituminous coals, could float in salt solutions without addition of any other flotation agents. The process is referred to as salt flotation. Other inherently hyhrophobic minerals (e.g. talc, graphite, sulfur, etc.) were shown to behave similarly (Klassen and Mokrousov, 1963)As Figure 1 shows, some coals float quite well in solutions of Na2SO4, NaCl and NaNO3 (Klassen, 1963). While there are differences between the tested salts (explained by different foamabilities of these solutions) all the tests indicate that only bituminous coals float well in concentrated electrolyte solutions. 0.3 M solutions are quite sufficient to initiate a good and very fast flotation. If wettability of various coals is compared it becomes obvious that these well floating coals are very hydrophobic bituminous coals (Figure 2)."

Jan 1, 2018