Search Documents

By Mauricio Guimarães Bergerman

At the regrind or secondary grinding stages of base metal ores, the concern about energy efficiency is usually extremely important. In general, the specific energy consumption at this stage is higher than during the primary grinding stages. In addition, a tendency of finer grinding has been observed in the new projects of metallic minerals, due to the finer mineral liberation, which leads to increasing capital and operational costs. At Vale?s new copper projects in Brazil, regrind sizes with a P80 of approximately 40 to 20 µm have been necessary. Conventional ball mills, adequate for primary grinding, usually bring about low energy efficiency with products bellow 50 µm. Vale is using the vertical mill on its copper projects ? Sossego and Salobo, in order to optimize the regrind of rougher concentrates and reduce energy consumption. This paper presents the results of industrial surveys carried out on the Vertical mill circuits of Sossego plant during its initial years of operation, and compares these results with the design criteria and laboratory regrind tests used for the mill scale up. Keywords: grinding, regrinding, copper, vertical mill, stirred mill

Sep 1, 2012

By E. Barsky

The composition of multi-component materials is proved to be unambiguously determined by the composition uncertainty parameter (composition entropy). At the same time, every component, depending on its content, introduces a certain value into this parameter. Quality criterion of multi-component separation is determined by the total change of this parameter for all products obtained as a result of the separation process. This parameter can unambiguously estimate both multi-product separation and complicated schemes of modern beneficiation plants. It can be used to estimate binary mixtures separation, too. During the optimization of multi-product separation, another problem arises, which is not peculiar to binary mixtures. In this case, the total efficacy depends on the order of separation boundaries, as well. In the present paper, a specific example of initial product separation into seven products by six boundaries is investigated. It is clear that with respect to a single boundary, two products only can be obtained. In this case, the separation optimum is shown to correspond to the separation of boundary-class particles equally into both products. We have also established that from the point of view of entropy, the maximal possible separation efficacy corresponds to equiprobable composition of the initial mixture, i.e., the fine product quantity in the material to be separated is equal to that of the coarse product. Three groups of experiments were carried out. In the first group, the boundaries were consecutively specified from the finest to the coarsest one. In the second group, the boundaries were set vice-versa, i.e., consecutively from the coarsest to the finest one. In the third group, no sequence was observed. At every separation stage, a boundary was specified in such a way that the separated material composition was as close as possible to equiprobable one relative to this boundary. Total efficacy was different in all the three cases. In third group of experiments, its value is the highest, which confirms the advanced supposition. The obtained results are phenomenological, ? they can be applied to any processes of solid, liquid and gaseous materials separation.

Jan 1, 2014

By M. S. Prithvi

Over the decades, mine and mineral processing plant operations for the most part, have been found to have had adverse impacts on the environment. At the same time, mineral processing and mining operations produce mineral products that are indispensable to modern society. Thus, the sector has desirable and undesirable attributes simultaneously. The situation presents itself as a contradiction (i.e.) the mineral processing and mining operations are wanted by society, and at the same time unwanted by society. The existing methods of addressing the issues raised above have evidently not been very successful in reducing the opposition to new projects and to the related activities such as land acquisition. This paper attempts to show the relevance and applicability of TRIZ for addressing the issue. TRIZ, or Teoriya Rezheniya Isobretatelski Zadach, is a Russian acronym meaning Theory of Inventive Problem Solving. TRIZ is a powerful tool that can be usefully applied to resolve such contradictions, using resources usually available within the system of interest. Accordingly, this paper introduces the issue background, followed by an introduction to some key concepts of TRIZ such as the 40 principles, separation principles and directed evolution. The paper goes on to apply the 40 principles to two case studies. The results show that TRIZ could be a useful tool to generate potentially innovative and sustainable approaches. Its most appropriate position would be as a supplement to current decision-making procedures, and as a validation tool to review existing solutions for possible improvements. Keywords: minerals, environment, TRIZ, contradiction, resources

Sep 1, 2012

Rotor speed is one of the key hydrodynamic parameters in froth-flotation and it plays an important role in bubble-particle attachment. Laboratory scale studies for optimizing the rotor speed to achieve maximum flotation rate constant (K) of quartz, ground by ball mill, are. Purity of quartz was 99.4 percent and d80 of ball mill product was 230 µm. Each size fraction was separately subjected to flotation at three different rotor speeds, namely, 1200, 1000 and 800 rpm, and the flotation rate constant was calculated. The results showed that the flotation rate constant was high at the rotor speed of 1200 rpm. The flotation rate constants achieved at 1200 rpm were 8.676, 8.232, 7.818, 7.248, 7.068 and 6.984 min-1forthesize fractions of +300, -300+250, -250+212, -180+150, -150+125 and -125+106 µm, respectively. Keywords: froth flotation, rotor speed, flotation rate constant, ball mill, quartz

Sep 1, 2012

By John Jiang, Brian R. Hart, Stamen S. Dimov, Aparup Chattopadhyay, Barun K. Gorain

"This paper presents a systematic approach to metallurgy diagnostics using an integrated gold deportment methodology developed for complex refractory gold and copper-gold ore bodies. Quantification of gold deportment for these ore bodies is a challenging task due to reasons such as lower grades, high variability of visible and invisible gold content in different sulphides and iron oxide phases, significant presence of disseminated and composite carbonaceous matters along with associations of various copper sulphide phases. Some case studies are presented in this paper to demonstrate the value of a high confidence gold deportment methodology in developing insights for problem diagnostics and to identify opportunities for metallurgical improvements. A holistic approach involving different fields of expertise is critical for successful development and delivery of solutions for complex ore bodies.INTRODUCTION Studies were initiated on various ore complex ore and also on samples representing various process streams. These complex copper-gold single refractory, double and triple refractory gold ores are mainly composed of silicates and/or carbonates with moderate amounts of clay and mica, along with minor amounts of sulphides and organic carbonaceous matter. Variable proportions of visible gold and “invisible gold” (sub-microscopic gold) were noted in different mineral phases for various ore types and process stream samples. Invisible gold commonly occurs as solid solution or as colloidal-sized particles in different sulphides (pyrite, arsenopyrite, pyrrhotite, chalcopyrite and galena) and other phases (including hematite, magnetite and goethite) for different refractory ores. The dominance of invisible gold and presence of highly preg-robbing along with finely disseminated carbonaceous matters adversely affects gold recovery in flotation and leach circuits for most of these double and triple refractory ores. This paper discusses applications of an integrated gold deportment technique developed for different types of gold and copper-gold ores, namely, complex copper-gold, double and triple refractory gold ores (Chattopadhyay and Gorain, 2014; Chattopadhyay et. al., 2016). Various process streams from flotation and gold leaching circuits were investigated. Different concentrates and tailings samples from flotation circuits whereas feed and discharges from pressure oxidation (POX) and carbon-in-leach (CIL) residues were used from gold processing circuits."

Jan 1, 2018

By Harshad Bhagwat

The objective of this work is to investigate the inadequacies of current CFD based methodologies of model development for predicting combustion behavior of pulverized coal in furnaces. In the present paper, a steady state CFD model was used for in-depth analysis of pulverized coal combustion. The model accounts for turbulence, coal combustion, convective and radiative heat transfer and motion of coal particles. It also uses coal combustion models to account for important processes such as devolatilization, combustion of char and the evolution of fuel nitrogen during coal combustion. The model predicts fluid flow, heat transfer, progress of combustion and pollutant formation (NOx, etc.). The model uses several parameters, which need to be tuned with experimental data, which is not only limited in quantity but also insufficient in detail. Various existing methodologies like part calibration method for tuning of the parameters are discussed. In the present work, the parameters associated with coal combustion models were tuned and validated with published data obtained from an experimental furnace using one such part calibration methodology. The results clearly show that the model predictions differed with the experimental data not only quantitatively but also qualitatively. These discrepancies were attributed to part calibration methodology. A detailed parametric study was carried out to demonstrate the importance of parameters from various classes, namely, combustion kinetics, heat transfer, process and geometry parameters, and CFD model parameters. This investigation clearly indicates that parameters from different classes have significant effect on combustion behavior. The discrepancies in current methodology are discussed and a need for comprehensive methodology is highlighted. Keywords: pulverized coal combustion, computational fluid dynamics (CFD), pollutant formation (NOx), mathematical modeling

Sep 1, 2012

By Hamid-Reza Manouchehri

"The triboelectric charge attributes of feldspar, quartz and wollastonite minerals, after contacting different triboecharging medium made of different materials, were considered. Their charge acquisitions by different size fractions of minerals were monitored and accordingly their energetic work function values were estimated. Moreover the separation behaviours of these minerals through the electric field of a laboratory free falling separator were determined and the effects of some chemical reagents on separation their separation characteristics were studied.Finally an attempt was made to translate the findings from single mineral systems to a complex silicate ore, containing quartz, feldspars, wollastonite and some other silicates. The results show favourable prospect to apply the triboelectric separation technique for beneficiation such a complex raw material."

Jan 1, 2003

By Benoit Clermont, Jan Lux

"Magotteaux and Anglo Platinum started a co-operation program with the main aim of establishing the optimum milling configuration measured in terms of throughput, fineness and energy consumption.For this purpose, a fully instrumented pilot milling plant, supplied by Magotteaux (Pty) Ltd, and equipped with a 0.9 x 1.0 m ball mill, was erected at Frank concentrator (Merensky Pt ore). The primary ball mills at Frank concentrator were surveyed in order to set the conditions for the base case. This data was then replicated in the pilot mill under the same configuration. Thereafter, a series of different parameters were varied in order to attempt to optimize the milling system.Some of the grinding parameters that have been studied are:•,Gate versus overflow discharge•,Open versus closed circuit•,Different filling degrees•,Different shell liner profilesOnly grate versus overflow discharge and open versus closed circuit will be discussed in this paper.It should be noted that this paper does not attempt to give a universal solution as to what milling configuration is optimum in all cases. The conclusions apply for this particular case and probably most others, but it would be advisable to consider each case on its own."

Jan 1, 2003

By M. Illikainen

Limestone is used for neutralization of acid leachates in a number of hydrometallurgical processes. The aim of this study was to clarify how limestone ground to different particle sizes can neutralize sulfuric acid. The laboratory scale ball mill was used in grinding experiments carried out using ball sizes of 20, 30 and 40 mm and volumetric slurry densities of 30, 40 and 50 percents. Varied grinding times were used in order to produce limestone samples with different particle size classes on which the neutralization potential and rate were determined. The results of the study showed that the neutralization potential of limestone is not dependent on its particle size between 5 and 120 µm. However, the particle size strongly affected the neutralization rate of sulfuric acid: The smaller the particle size, the higher the rate of neutralization. Thus, when optimizing the cost efficiency of the process, the optimal degree of grinding should be considered taking in account the required residence time in neutralization phase.

Sep 1, 2012

By W. Yao, M. L. Li, R. Cui

"The purpose of this research is providing a flotation process for recovery of lead in lead silver residues from a zinc smelting plant with a new hydroximic acid collector (HOC). The collecting ability and reaction mechanisms of HOC were investigated based on pure mineral flotation tests and analysis of zeta potential. The pure anglesite flotation tests showed that HOC has a good collecting ability for anglesite. Zeta potential measurements proved that HOC adsorbed on anglesite surface physically and chemically. The lead-silver residues in a zinc smelting plant with lead grade about 17.5% was used as raw material for flotation tests. The results showed that under the conditions of pH adjusting agent lime 500g/t, inhibitors sodium silicate 2000g/t, collector HOC 1500g/t, frother alcohol oil 75g/t, the grade of the lead concentrate can be reach 47.18% and the recovery was 76.39% by one roughing-one scavenging-three cleaning and middles back to the flow-sheet in turn after the lead-silver residues were washed by two stages of cleaning-filtration.INTRODUCTION Nowadays, with the increasing exploitation of natural mineral resources, more and more secondary resources should be researched and used for the valuable metals. Hydrometallurgical zinc leaching residues, which contain a considerable amount of zinc, lead, silver and other minor valuable constituents, is a typical and abundant secondary resources (Zhang et al., 2011). A huge quantity of zinc leaching residues (ZLR) had been produced per year (Jiang et al., 2017).This residues not only occupy precious land but also threaten the environment because of the dissolved heavy metals especially in rainy days (Han et al., 2014). Consequently, it is urgent to develop an effective and clean method to dispose this residues which can benefit not only in economical but also in environmental (Jha et al., 2001)."

Jan 1, 2018

By O. Martinsson

The Kiruna area is an important mining province in northern Sweden, which is dominated by Fe- and Cu-Au deposits. Economically most important for the region, are the apatite iron ores with an annual production of c. 43 M ton of crude Fe-ore and a total production of more than 2000 M ton of ore the last 100 years. The apatite iron ores in the Kiruna area are dominated by either Magnetite or Haematite and contain varying amounts of apatite giving them a content of Fe and P, which varies between 30-70 % and 0.05-5 %, respectively. A typical geochemical feature of the ores is the strong enrichment of REE that is caused by a high content of REE in apatite and the occurrence of Allanite and Monazite containing 22.4 and 69.8 wt% REO, respectively. At Kiirunavaara, the content of REE in apatite varies between 0.07 to 1.57 wt% REO with a dominance for the light rare earths. The variation in REE-content of apatite depending on textural and paragenetic aspects is not known but apatite grains may display a strong LREE-depletion due to hydrothermal alteration. Monazite occurs as rod-shaped or tabular inclusions in apatite and is suggested, to have formed in response to hydrothermal alteration of apatite after the emplacement of the ore. Inclusions are mainly found in the central part of apatite grains occurring in veins and schliren, while they are rare in apatite occurring disseminated in the ore. Monazite also occurs as larger grains outside apatite and together with Allanite is found in texturally and paragenetically different settings within the ore. These occurrences of REE-minerals may largely be a product of LREE mobilized by alteration of apatite after the emplacement of the ore. However, REE-minerals including Allanite and Monazite might also have formed directly from late magmatic fluids. Keywords: apatite, monazite, allanite, ree, kiirunavaara, iron ore of kiruna type, mineral chemistry

Sep 1, 2012

By K. Anand Rao

Extensive exploration for uranium metal by the Department of Atomic Energy in India led to the discovery of new carbonate host rock uranium deposits Tummalapalle and Gogi, which are located in southern part of India. Alkaline leaching at elevated temperature and pressure using autoclave is the central unit process in the overall strategy for extraction of uranium from these new ore deposits. Autoclave leaching is affected largely by intrinsic nature of the ore and by the process variables and the equipment settings. In order to understand such a complex process and also to be able to predict the process performance under randomly (ore grade, uranium mineralogy, gangue mineralogy etc.) and consciously perturbed variable settings (partial pressure of oxygen, temperature, concentration of leachant, stirring speed and time), sound and robust mathematical models are needed with analytical and/or numerical solutions. Present investigation attempts to develop a variant of kinetic correlation based on shrinking core model for batch alkaline leaching process in an autoclave. The leaching model incorporates particle size distribution according to popular Gates-Gaudin-Schuhmann equation, rather than assuming a single mean size for all the particles participating in the leaching reaction. Kinetic experimental data generated in autoclave leaching of Gogi uranium ore was used to evaluate various constants of the model developed. The ore sample used for experiments assayed 0.21 per cent U3O8. The partial pressure of oxygen was varied between 0.15 to 6.5 atm, temperature from 343 K to 438 K, concentration of sodium carbonate leachant in the range 0.47 g mol/L to 0.94 g mol/L, and the stirring speed from 573 rev/min to 900 rev/min in the experiments. The goodness of fit of the leaching process model is found to be >0.95. Morphological studies carried out on leached and unleached particulate matter using Scanning Electron Microscopy with Energy Dispersive X ray analyses are included in the present study.

Sep 1, 2012

By S. F. Ye, L. Xiao, Y. L. Wang, P. W. Han

"Copper anode slime is a precious secondary source for the recovery of silver. However, current recovery process are constrained by either sever pollution or high cost. To cover the drawbacks of current process, this research employed a novel strategy by using the manganese dioxide as the oxidant in acid solution, which avoided the generation of sulfur dioxide while high silver extraction rate was achieved. The effects of manganese dioxide, sulfur acid concentration, stirring speed, temperature and leaching time on silver extraction rate were investigated. The silver recovery reached to 91.68% under the conditions of 1.2 g manganese, 2.0 mol/L H2SO4, 300 rpm, 80 °C and 6 h. INTRODUCTION Copper anode slime is generated from the electrolysis refining of copper and is extremely precious for its containing noble metal such as silver (Chatterjee, 1996; Amer, 2003; Yldrm et al., 2014; Syed, 2016; Wang et al., 2017). Therefore it is of great significance to extract silver from anode slime for the full utilization of resource. Pyrometallurgy is the most mature process for the extraction of silver because of its stability and adaptability (Hait et al., 2009; Zhao et al., 2010; Gao et al., 2017). However, it also suffers the drawbacks of high operating cost, low extraction rate of silver and severe pollution of smoke dust (usually containing lead and arsenic) (Ludvigsson and Larsson, 2003). To cover the drawbacks of pyrometallurgy process, more and more attentions are giving to the semi-hydrometallurgy process which usually includes a pretreatment process of sulphatising roast or low temperature oxidizing roasting (Tishchenko, 1964). After pretreatment, the refractory silver bearing phases (silver selenide, silver sulfide and silver) are converted into readily leached forms which are often extracted by ammonia, sodium sulfite in alkaline solution (Valiuniene et al., 2010; Wojciech, and Kitka, 2017). Despite its relatively high extraction rate and low investment, it still has the disadvantages of releasing harmful gases since the sulfur dioxide are generally generated in the pretreatment process. In addition, the use of ammonia can easily lead to a leaking into the atmosphere once not carefully dealt with (Aylmore and Muir, 2001). As for silver recovery by sulfite leaching, the consumption of sodium sulfite is rather high which often results in a pipe blocked (Yang et al., 2006)."

Jan 1, 2018

By E. V. Koporulina, I. Zh. Bunin, M. V. Ryazantseva

"We studied the mechanism of structural and chemical transformations of columbite, tantalite, zircon and feldspar surface during the treatment by high – power electromagnetic pulses (HPEMP) using the methods of X - ray photoelectron spectroscopy (XPS), analytical electron microscopy (SEM - EDX), Kelvin probe force microscopy and flotation experiments. According to XPS and SEM - EDX data, major changes in the atoms chemical state of investigated minerals surface are related with formation and modification of functional cover and changing in concentration (% at.) of hydroxyl groups on the mineral surface, leading to increase in the contrast of technological properties of the rare metals minerals. Research has identified the optimal parameters of HPEMP - treatment of rare - earth minerals Npuls ??104, Ttreatment ??100 sec. improving the selectivity of the flotation separation of columbite and zircon. The difference in mineral recovery into the froth (? e) before and after HPEMP - treatment was about 11 % and 24.5 %, respectively. No significant increase was observed in the flotation activity of feldspar. This study's findings demonstrate the effectiveness of HPEMP - treatment in inducing a controlled change in the structural and chemical properties of rare - earth minerals and improving the process efficiency for the processing of rougher tantalum - niobium gravity concentrates.INTRODUCTIONThe importance of improving the processing methods of tantalum-niobium ores and concentrates is explained by the mineralogical properties of rare - earth ores. These are properties such as the variable mineral, chemical, and grain size composition, complex morphometric properties, and the dissemination of ore mineral grains of micro - and nanometric size. Iron oxide and hydroxide films on the mineral surfaces neutralize the surface physicochemical and absorption properties of the minerals. Both in Russia and globally, nonconventional (non - mechanical) methods are being developed based on physicochemical, electrochemical, and pulsed energy impacts to improve the efficiency of disintegration and liberation processes of disseminated mineral complexes and to enhance the contrast of the structural, chemical, and technological (floatability) properties of refractory ores. This study is devoted to the investigation of the applicability of high – power electromagnetic pulses (HPEMP – treatment) for the change in the structural and chemical properties of rare - earth minerals and improving of the flotation properties contrast."

Jan 1, 2018

By E. V. Koporulina, I. Zh. Bunin, M. V. Ryazantseva

"We studied the mechanism of structural and chemical transformations of columbite, tantalite, zircon and feldspar surface during the treatment by high – power electromagnetic pulses (HPEMP) using the methods of X - ray photoelectron spectroscopy (XPS), analytical electron microscopy (SEM - EDX), Kelvin probe force microscopy and flotation experiments. According to XPS and SEM - EDX data, major changes in the atoms chemical state of investigated minerals surface are related with formation and modification of functional cover and changing in concentration (% at.) of hydroxyl groups on the mineral surface, leading to increase in the contrast of technological properties of the rare metals minerals. Research has identified the optimal parameters of HPEMP - treatment of rare - earth minerals Npuls ? 104, Ttreatment ? 100 sec. improving the selectivity of the flotation separation of columbite and zircon. The difference in mineral recovery into the froth (? e) before and after HPEMP - treatment was about 11 % and 24.5 %, respectively. No significant increase was observed in the flotation activity of feldspar. This study's findings demonstrate the effectiveness of HPEMP - treatment in inducing a controlled change in the structural and chemical properties of rare - earth minerals and improving the process efficiency for the processing of rougher tantalum - niobium gravity concentrates.INTRODUCTIONThe importance of improving the processing methods of tantalum-niobium ores and concentrates is explained by the mineralogical properties of rare - earth ores. These are properties such as the variable mineral, chemical, and grain size composition, complex morphometric properties, and the dissemination of ore mineral grains of micro - and nanometric size. Iron oxide and hydroxide films on the mineral surfaces neutralize the surface physicochemical and absorption properties of the minerals. Both in Russia and globally, nonconventional (non - mechanical) methods are being developed based on physicochemical, electrochemical, and pulsed energy impacts to improve the efficiency of disintegration and liberation processes of disseminated mineral complexes and to enhance the contrast of the structural, chemical, and technological (floatability) properties of refractory ores. This study is devoted to the investigation of the applicability of high – power electromagnetic pulses (HPEMP – treatment) for the change in the structural and chemical properties of rare - earth minerals and improving of the flotation properties contrast."

Jan 1, 2018

By V. A. Luganov

The processing of pyrite concentrates may be accomplished with a preliminary enrichment due to withdrawal of iron sulfides from initial concentrate. The withdrawal of iron sulfides is possible with the help of magnetic separation when the magnetic iron sulfides (pyrrhotites) separate from non-magnetic fraction?the sulfides of non-ferrous metals. The conversion of non-magnetic pyrite to magnetic pyrrhotites of adjusted structure occurs because of roasting with the withdrawal a part of sulfur. The resultant pyrrhotites are strong ferromagnetic with hexagonal structure. This paper contains results of studying magnetic properties of pyrrhotites, findings of the de-composition of initial pyrite with the consequence homogenizing of product and hardening of product of decomposition in liquid nitrogen. Define the type of pyrrhotites super lattice structure, was established that at increasing of sulfur contention the magnetic properties of pyrrhotites are change ? pyrrhotite begin evince the properties of antiferromagnetic material and magnetic susceptibility of material is interruptive changing from 0 to 1.7×10-3~1.9×10-3 SI units/g system. The paper contains results of technological researching of pyrrhotizing-magnetizing roasting of pyrite concentrates in different condition: in unoxidizing, with the decreasing contention of oxygen and in autogenous regime in air atmosphere. Established that the magnetic susceptibility of products depend of pyrite degree dissociation and achieve 2×10-3~3×10-3 SI units/g system at 40%~45% desulphurization. Defined the conditions of steady regime autogenous roasting, at resultant products possess coefficient of magnetization, and this can be used magnetic separation for separating ferromagnetic pyrrhotites from gangues and non-magnetic sulfides of non-ferrous metals. This technology of pyrrhotizing roasting is recommended for effecting in industrial condition. The initial materials and products of roasting subjected to chemical, thermogravimetric, Moss-bauer spectroscopy and X-ray analysis, defined the magnetic properties.

Jan 1, 2014

By Jun Xiao, Yucai Zhou, Yanhong Dong, Daixiong Chen

"In this article research on the mineralogical characteristics and beneficiation process for a copper molybdenum deposits in Heilongjiang province of China has been carried out. Chemical analysis, X-ray diffraction(XRD) and Quantitative Evaluation of Minerals by SCANning electron microscopy (QEMSCAN) were conducted on samples. The bulk analysis results showed that: (1) Comprehensive recovery and separation of molybdenum & copper minerals was feasible by the flowsheet of first copper-molybdenum mixed flotation after grinding the ore samples to 61.88% -74µm and then separation flotation of copper and molybdenum after regrinding the Cu-Mo mixed concentrate to 83.26% -38 µm. The results highlight relationship between mineralogical characteristics of ore and comprehensive benefication method. (2) the combination of "" Sodium sulphide and sodium thioglycolate "" reagents are effective inhibitors of copper-molybdenum mixed concentrate, their selectivity performance is better than that of single reagent. Good flotation indexes were gained that might be directive experience to similar cases. KEYWORDS Mineralogical characteristics; molybdenite; chalcopyrite; flotation separation; inhibitor INTRODUCTION Copper and molybdenum metals are widely used in the field of metallurgy, aerospace, national defence, etc. Copper –molybdenum sulphide ore is an important source of copper and molybdenum metals. At present flotation is still the preferred methods to deal with the copper-molybdenum sulphide minerals (Yin, Z., Sun, W.et al. 2017; Ansari, A., & Pawlik, M. 2007; Hirajima, T., Miki, et al. 2017). Copper and molybdenum sulphide ores usually have the similarly good nature floatability(Miki, H., Matsuoka, et al. 2017), meanwhile most molybdenum sulphide ore has tiny grained-size(Castro, S., & Laskowski, J. S. 2015.) and closed relationship with other sulphide and gangue minerals which result in the coper and molybdenum separation problem. Base on the nature of the ore and flotation properties of the individual minerals contained in the ore, there are two methods are usually used to deal with the copper – molybdenum ore, including bulk molybdenum/copper flotation followed by separation of copper and molybdenum minerals, sequential molybdenum/ copper flotation(Liu, G. Y., Lu, et al. 2012). The latter method has the shortcoming of hard to activate the depressed copper minerals in the previous molybdenum flotation process, which may result in a large loss of the copper from concentrate, this disadvantage would avoid while adopting the former method. bulk flotation followed by separation process is to get the copper-molybdenum concentrate from raw ore first then separate flotation the molybdenum and copper minerals, benefit from the excellent floatability of both molybdenum and copper minerals ( Malhotra, D., Rowe, R. M., & Bhasin, A. K. 1986; Cao, Z., Yue, et al. 2017 ), it really easy to obtain the mixed concentrate. In order to get the high quality copper and molybdenum concentrate, the key technologies and difficulties are to realize the separation of the copper and molybdenum minerals which have the very similar natural floatability (Raghavan, S., & Hsu, L. L. 2015; Nakhaei, F. 2014)."

Jan 1, 2018

Deposit of Jinbaoshan platinum group metals (PGMs) ore ranks the second in Yunnan province, China. Study on process mineralogy shows that the grade of copper and nickel in the ore is just 0.16% and 0.20% respectively. Moreover, the impurities magnesium and iron and silicon are rich in the ore. The copper and nickel sulfides in the ore, especially the minerals of PGMs, are finely disseminated with the gangues like serpentine. Fine grinding is necessary, and high content of MgO in the concentrate is inevitable through traditional flotation technology on the basis of process mineralogy studies. Achievements on process mineralogy studies are applied to guide the flotation tests successfully. Progress on flotation has been made through comprehensive studies. Suitable grinding by two stages is required for the finely disseminated PGM sulphide ore to achieve the liberation of valuable minerals. Stage grinding and stage separation shall be conducted for a better recovery of valuable minerals. The oxidation state of mineral surface of sulphides has a profound effect on flotation of the ultra-fine sulphides, especially the pentlandite. The combined use of collectors enhances the selective collecting on the ultra-fine and low-grade valuable minerals, is of critical importance.

Jan 1, 2014

By Marco Le Roux, Quentin Campbell

"Most coal supply contracts include strict limitations on the moisture content of the products. This limitation exists because of calorific, transport cost, and handling reasons. Managing the retention time on product stockpiles to facilitate drainage commonly controls the moisture content in coarser coal products. A large-scale pilot rig has been commissioned to facilitate research in this regard. A stockpile of about 15 tonnes of a typical washed power station feed coal from the South African Witbank coalfield was loaded onto a 6 x 6 m platform on load cells. The platform was shielded from the elements, like rain and wind, and an artificial rain sprinkler system was installed. A variety of rainfall intensities and durations were simulated and the water accumulation and run-off was measured. The material was also sampled for moisture and particle size before and after the series of tests. At the same time, the drainage characteristics of the same coal were determined in smaller scale drainage columns for comparison. Data is presented in this paper on the drainage rates, maximum accumulated moisture, final moisture, and the effect of evaporation. The results showed that for all rainfall patterns tested, drainage ceased after 2 - 3 days, but evaporation continued for at least the time period under investigation, albeit at a low rate. Evaporation contributed to dewatering at rates that depended on wind, temperature and humidity conditions. This caused a slow reduction in moisture content even after the run-off had ceased. The value of the final moisture depended on the coal PSD. It was also found that the intensity and duration of the more intense rainfall events did not significantly affect the maximum water accumulation, with drainage rates equaling the corresponding water addition rates which suggested that water ran off over the surface of the stockpile with limited penetration. During more intense rainfall scenarios, some penetration was apparent."

Jan 1, 2014

By R. S. C. Smart

Surface chemical factors, including the balance of hydrophobic (e.g. collectors) and hydrophilic (e.g. oxidation products, precipitates) species, are major control determinants in flotation rates of specific minerals and therefore grade and recovery. There are a number of challenges involved with the surface analysis of different mineral phases from process streams in a flotation facility. The first is to collect samples that are representative of the process and retain their surface chemistry prior to introduction into the instrument. The second challenge in studying the surface chemistry of specific minerals is to find reliable methods of mineral phase recognition. In surface analysis of mineral particles, confident mineral selection can be difficult with many multi-metal minerals and with precipitated, adsorbed, reacted and contaminant species in the outermost molecular layers. The third challenge is to provide a statistical surface analysis of multiple grains of the same mineral. Methods to achieve these aims are described. Principal component analysis (PCA) of ToF-SIMS data provides improvement in phase recognition, particle selection and associated variations in surface species. Specific examples from both lab and plant operations, demonstrate that this technique can be utilized to differentiate surface chemical factors promoting (hydrophobic species) or inhibiting (hydrophilic species) flotation. A study of copper ion transfer (inadvertent activation) from chalcopyrite to pyrite and sphalerite clearly identified a statistical difference in copper intensities between the sphalerite and pyrite phases corresponding to their flotation response. The PCA analysis applied to concentrate and tails samples collected from the Inco Matte Concentrator demonstrated extensive CuOH and NiOH transfer between chalcocite and heazlewoodite minerals. The statistical analysis has been able to identify mechanisms controlling recovery and selectivity. High intensity conditioning (HIC) tests in which sphalerite was separated from a complex sulfide ore gave a 5% increase in the overall Zn recovery. The PCA/ToF-SIMS statistical analysis revealed the discriminating depressant action of adherent aluminosilicate (gangue) fine particles and adsorbed ions on the surface of sphalerite grains. HIC conditioning resulted in the removal of these gangue fines improving surface collector attachment efficiency.

Jan 1, 2014