Search Documents

Pure camsellite samples were prepared through crushing, sorting and grinding the high-grade iron-containing camsellite ores from Fengcheng, Liaoning, China. The flotation behaviour of camsellite was studied via a systematic investigation of camsellite flotation re-covery changes as a function of choices and dosages of collectors and depressants at different slurry pH. The results showed that at pH 8.5 to 9.5, the recovery of camsellite reached the maximum at 90%~93.5% using dodecylamine as the collector, while under the same condition a recovery of 84%~86% could be achieved with sodium oleate. The adsorption of dodecylamine was not affected by the addition of sodium hexametaphosphate, but the adsorption of sodium oleate could be significantly depressed. This implied that sodium metahexaphosphate could be used as an effective depressant for the other associated minerals during the dodecylamine flotation of camsellite. When starch was used as the depressant, the flotation of camsellite by sodium oleate was almost completely depressed in the alkaline conditions. Significant depressions were also observed when calcium chloride was added in the camsellite-sodium oleate system. The higher the slurry pH is, the stronger the depression. Zeta potential measurements indicated that the flotation was mainly initiated by the electrostatic adsorption of the collector on camsellite. X-ray photoelectron spectrometer (XPS) analysis showed that the adsorption was originated from the electrostatic attraction between the N atom in dode-cylamine and B atom in camsellite. Dodecylamine had a higher coverage on the camsellite surface than sodium oleate.

Jan 1, 2014

By Prasad Kopparthi, Narasimha Mangadoddy, Balraju Vadlakonda, A. K. Mukhurjee

"Column flotation (CF) is widely using equipment in mineral processing since many years. ERT technique facilitates non-invasive and nonintrusive visualization of different parameters in a column flotation. The hydrodynamic investigation of two-phase and three-phase are studied using electrical resistance tomography (ERT) coupled with pressure transducers in laboratory column flotation. Bubble size distribution, bubble rise velocity and gas and solids hold-up hydrodynamic parameters are extensively used for column flotation design and performance evaluation. The effect of superficial gas velocity, feed flow rate and slurry height in the column on mean gas holdup and its radial distribution has been analyzed for both two-phase and three phase flows. Influence of solid particles on gas hold-up and its complete elucidation of dispersion in the column are assessed. Experimental results show ERT coupled with PT is suitable as an online monitoring tool to provide useful information on the hydrodynamic parameters of the column flotation. The tomography images, which were generated using a modified sensitivity back projection algorithm, were employed to explore the parameter study in two phase flow in column flotation.Furthermore, the results also indicate that ERT is a very powerful tool for diagnosing the `inside' flow behaviour of gas-liquid two-phase and gas–liquid–solid three-phase flow in columns operating for a wide range of flow regimes.INTRODUCTIONColumn flotation is being widely used in mineral processing industries in last few decades. There has been a lot of attention in understanding the various mechanisms that take place during operation. Due to many reasons column flotation has been found to yield better performance than conventional flotation cells, particularly with fine particles (Honaker and Mohanty, 1996). Due to complex flow behavior in nature, the performance of column flotation influenced by on flow characteristics of the process, (Jena et al., 2008). Previously basic research is carried out to evaluate the effect of the hydrodynamic parameters on the performance of column flotation (Finch and Dobby, 1991)."

Jan 1, 2018

By Glaser. C., J. Balz, F. Logsch, R. Heiduschke, M. Leiker, P. Ay

The treatment of iron-hydroxide-containing water from ground water and surface water is achieved by a combination of the process steps of flocculation and subsequent mechanical dewatering. The aim is to create solid pellet structures by extending the structure forming flocculation process with a build-up pelletizing process which can be transferred directly into a drying unit. A Taylor-Couette-reactor (diameter of the inner cylinder – 40 mm, gap width – 5 mm) was used for these experimental studies. To produce the necessary flow profile the inner cylinder was rotated at a speed of 230 rpm. The iron hydroxide-containing suspension (dry matter content: 2 mass %) was added simultaneously with the addition of a cationic high-molecular flocculant in various flocculant dosages and residence times of 5 to 15 min. The pellets were examined for parameters such as geometric dimensions, dry substance content and dewatering behaviour. As the results show, there is a direct relationship between the residence time and the geometric dimensions of the pellets. After a residence time of 5 min, round pellets with an average diameter of 6 mm were formed. With an increase in the residence time up to 15 min, a compaction of the pellets could be observed, which resulted in an increase in the dry substance content of 8.0 to 11.2 mass % on average. After completion of the pelletizing process, the pellets were mechanically dewatered by filtration. By applying this innovative wet pelletizing of iron-hydroxide containing suspensions in a Taylor-Couette-reactor, it is possible to carry out the process of flocculation combined with the pellet formation with simultaneous pellet compaction in a single process step. The resulting pellet structures are distinguished from conventional floc structures by an improved water discharge capacity. After classification the pellets can be marked directly as easy-to-handle bulk material, suitable as feedstock in percolation columns for the purification of contaminated fluid streams

Jan 1, 2018

By M. Kosugi, M. Kawata, J. V. Satur, K. Mitsuhashi, R. Kawarabuki, W. Kracht, Y. Ebisu

Copper concentration is becoming more difficult because remaining copper ores are more complex and of finer copper mineral grain size, making copper minerals harder to float because of the fine particle size required to liberate the valuable species. The purpose of this work was to study the flotation behavior of fine copper sulfide ores at different conditions of agitation and aeration. The experimental campaign was carried out in a laboratory Denvertype flotation cell of 1 L volume modified to be operated with forced air that allows decoupling air flow rate and agitation speed. Four ore samples from Chile were used, all of them containing copper sulfides such as chalcopyrite, bornite, chalcocite, and tennantite, but with varying grain sizes and compositions. Preliminary flotation tests for establishing the flotation conditions of grinding size and collector dosage were conducted before the kinetic flotation tests that were carried out at different agitation speeds varying from 900 to 1300 rpm for gas flow rate ranging from 1.6 to 7.2 L/min. The flotation products were analyzed by ICP-MS and MLA (Mineral Liberation Analyzer). The results showed that high agitation speeds with corresponding air flow rates resulted in better recovery than moderate agitation speed and air flow rate, and an excess in gas flow rate resulted in bad performances. The flotation rates of the fine copper minerals were improved despite the different improvement rates among the fine size fractions. The impact of these operational variables, however, was different when comparing the results for the four ore samples. While it was found that the order of floatability in the four samples was the same, that is, chalcocite > tennantite > bornite > chalcopyrite, the kinetic constants of the copper minerals in the samples were different, indicating that mineral composition in the sample affects the flotation kinetics.

Jan 1, 2018

By M. Evertsson, E. Hulthén

"In aggregate production and mining the operators are responsible for controlling and monitoring the process to maintain high plant throughput and safe operation. Operators have to make different decisions to control the process due to changed demand on the operation from both management and conditions of the process. The quality of the response and the time it takes for an operator to respond to altered demand relies on what information is available and the experience of the operator. In this work a dynamic simulation platform has been developed to be used for operator training. Models for representing production units and process control for plant simulations have been developed and implemented in MATLAB/SIMULINK to simulate time-dependent plant behavior. Stochastic and scheduled events are included using the discrete events simulation toolbox SimEvents. The human-machine interface was developed using the human-machine interface software ICONICS. The operators’ cognitive process, in interpreting the plants semantic, has been studied by observations and with informal interviews with operators. This was done to get information about the daily operation and the problems that occur in the process. By interacting with operators that experience different physical interactions with the process; more qualitative e-learning software for supporting operator training in a dynamic operator environment could be developed. The quality of the operator training environment was evaluated with a usability study that was performed with operators and others within the production."

Jan 1, 2014

By H. J. Liang

In this study, zeta potential and contact angle measurements of pyrite before and after interacting with Thiobacillus ferrooxidans are carried out to investigate the changes in its surface properties. The results show that, after pyrite interacting with Thiobacillus ferrooxidans and its metabolite, the surface electricity of pyrite changes obviously, resulting in a notable shifting of isoelectric point to lower pH value, but the contact angle varies little. Bacterial protein plays the most important role in the interaction. This work is helpful to disclose the mechanisms of Thiobacillus ferrooxidans de-pressing pyrite flotability.

Jan 1, 2014

By Lei Zhang, Xianjun Lu1, Minjie Lian, Liyang Zheng

In order to investigate rheological behaviour of fine tailings backfill pastes, the fine iron ore tailings (size fraction of -0.074mm accounts for 70%) from Fuquan Mining Co., Ltd. of Sinosteel Corporation (Shandong, China) was investigated. The rheological parameters such as slump, viscosity and yield stress of the tailings pastes under different densities were measured in detail, and the effect of paste density on the rheological property and the relationships of different rheological parameters of the pastes were also discussed. According to the results, the rheological behaviour is in accordance with the pseudoplastic fluid in a wide range of paste densities (solid content, w/w) of 65% to 80% and the pastes turn to be Bingham fluids at higher shearing rates. Along with the increase of paste density, the slump drops gradually and the viscosity and shear stress increase gradually. However, the variation extent of the rheological parameters varies at different density ranges. According to the variation pattern of the rheological parameters at different paste densities, the flow ability of the pastes can be classified into three zones. The high fluidity zone was observed at the density range of 65%-69% where the rheological parameters vary slightly along with the paste density, the moderate fluidity zone was observed at the density range of 70%-76% where the rheological parameters vary significantly along with the paste density, and the low fluidity zone was observed at the density range of more than 76% where the rheological parameters vary sharply along with the paste density and the critical density for this sudden variation is about 76%. Furthermore, linear correlations of slump/viscosity and slump/yield stress were observed. It is possible to predict the viscosity and yield stress of the pastes based on the slump measurements.

Jan 1, 2014

By Gülay Bulut, Ferihan Göktepe

Pyrite is the most abundant and widespread sulphide mineral and its flotation has been investigated by many researchers. It is well known that, pyrite is floatable under acidic conditions and recovery drops with increase in alkalinity due to changes in solubility of iron hydroxides on the pyrite surface. Most of the works also revealed out that pyrite displays variable behaviour in flotation circuits. This behaviour mainly related with origin and mineralogical composition of ore, liberation size, electrochemical behavior of minerals constituting ore, the trace and minor element content of the mineral, texture, application variables belonging to flotation circuits. In this study, copper activation effect was examined on different origin of pyrites. The experiments were performed with five high grade samples of pyrite from the different mining districts of Turkey. The pyrite samples were different from each other with respect to either their physical or chemical properties; they were different physical appearances and contained different associated minerals. In the micro-flotation tests, 1x10-4 mole/L copper sulphate and 1x10-4 potassium ethyl xanthate were used as flotation reagents. First of all pyrite samples were floated using only xanthate at different pH. Results showed that best floatation results obtained at acidic pH range for all pyrite samples. When copper ions were used to activate, all pyrite samples floated at neutral and basic pH values, too but depending on the samples, recovery and pH ranges were slightly changed.

Jan 1, 2014

By V. Avzian Belozersky reg 453524, Vasily V. Lodeischikov, Adolf F. Panchenko, Til E. Vidusov, Olga D. Khmelnitskaya, Vladimir E. Dementyev

"Presently, there is a number of gold deposits which cannot be developed using the conventional technologies with acceptable economic indices due to low gold content, high depth of ore occurence and other conditions. For such ores, an innovation technology of underground gold leaching in the place of their occurrence is of special interest. The technology excludes ore mining and hoisting to the surface. This enables the production cost of 1 g of gold to be considerably reduced in comparison with conventional methods of gold recovery.The Maminskoye deposit oxidized ores were chosen as the subject of underground leaching because they are ideally suited for this purpose due to their composition and hydrological parameters. The ore reserves within the underground leaching block are 90, 000 t with 0.7 g/t average gold grade.An experimental system for underground leaching with a throughput of 15 cubic m solutions per hour was developed. A combined filtration-and-infiltration system of the ore massif development by holedrillingwhere pregnant solutions are air-lifted was worked out.The underground leaching flowsheet includes Au dissolution by chlorine-containing solutions, Au adsorption from solution onto active carbon, carbon concentrate ashing and calcine melting to produce Dore metal."

Jan 1, 2003

By R. ?. Sherembayeva, ?. ?. ?uktybayeva, ?. B. Rakhimbekova, N. ?. ?m?rova

"Studying the interaction of the phosphorus-containing flotation reagent with the components of the flotation system ""liquid-gas-solid"" during flotation of non-ferrous metal ores allows regulating the enrichment process. The phosphorus-containing reagent-collector anabasinium-O,O-dimethyl-thiophosphate has beensynthesized under laboratory conditions and the concentrated aqueous solution of anabasin hydrochloride and the 40% solution of sodium hydroxide have been used as the raw material. The phosphorus-containing reagent has been obtained by interaction of the anabasine base, sulfur and dimethyl phosphite, due to sulfur and nitrogen atoms it can form complex compounds with heavy metal ions.Studying flotation of copper-sulfide ore of the Sayak field with the use of the phosphorus-containing reagent-collector anabasinium has been performed in the open and closed cycles. The degree of ore grinding was 60- 62% of the class -0.074 mm. There has been established the dependence of the ore flotation parameters on: a) pH of the pulp; b) the consumption of the reagent-collector anabasinium.The effect of the pulp pH on the technological parameters of copper ore flotation has been carried out with a reagent regulator that increases the difference in the surface properties of the minerals to be separated.There has been used lime as the regulator of the medium, the consumption of which varied from 750 to 1500 g/t; the consumption of the reagent-collector anabasinium was 10, 15, 20 and 25 g/t.It has been found that when flotation of copper ore without the use of lime at pH equal to 7.8 and at the reagent consumption, g/t: anabasinium - 25, T-92 - 55, copper recovery in the concentrate is 92.72%, the quality of concentrate is 7, 1%.In flotation according to the factory mode (the consumption of xanthate is 44 g/t, T-92 is 55 g/t, pH = 7.8 (without lime)) of copper ore, copper recovery in the concentrate is 87.38%, the concentrate quality is 7, 97%, with reducing the xanthate consumption to 25 g/t copper recovery is reduced to 83.39%, the quality of the concentrate is up to 6.69%.In the experiments using the factory reagent mode in the closed cycle, with the xanthate mass consumption of 44 g/t, T-92 blowing agent of 55 g/t, the third recleaning concentrate contained 19.13% copper with recovery of 86.89%.Using a phosphorus-containing reagent instead of xanthate with the same flow rate, the third recleaning concentrate with the mass fraction of copper of 19.82% has beenobtained with recovery of 87.77%."

Jan 1, 2018

By Hamid-Reza Manouchehri, Hassna Aitahmed-Ali, Stellan Sundberg

"In flotation practices as the particle size becomes fine, e.g., p<20µm, the process efficiency declines markedly. When flotation of fine particles is necessary, one method to improve the recovery is selective agglomeration of fines. Different agglomerating methods have been introduced and tested; however, one method which has recently received great attention is to aggregate fine particles by magnetic force. A selective aggregation of the fine paramagnetic particles, e.g., sulfide minerals, can be achieved by applying a high intensity magnetic field during flotation conditioning. The method is simple, selective and effective for fines, and has a low operation cost. However, a minimum magnetic susceptibility of fine grains is required for this process. This method has been demonstrated in different sulfide minerals flotation plants. The implementation of the magnetic conditioning device, ProFlote, in both the Cu-Pb and the Zn circuit of Boliden’s Garpenberg plant in Sweden, where a complex massive sulfide ore is treated, is discussed herein. The preliminary results have shown an increase in the recovery of value minerals, in particular Zn and Ag and considerable reduction in Zn deportment to the final tail. Increases in Cu grade and decreases in Pb grade in Cu-con have been achieved as well."

Jan 1, 2014

By Joseph Kelly, Christopher Kelsey

This revolutionary super-fine crusher has the unique capacity to generate fine and ultra-fine products from single stage reductions of coarse or fine mineral feeds. The crusher consists of a rotating compression chamber and an internal gyrating mandrel. The axis of rotation of the shell is displaced relative to the axis of the vertically mounted mandrel. The inner surface of the compression chamber is machined as double cone frustums at an angle equal to the displacement angle. Crusher feed is accelerated into a compacted particle bed, which lines the inside of the compression chamber. The depth of the compacted bed progressively increases until the mandrel is engaged. The mandrel is then free to rotate with the compression chamber. Continued feeding increases power draw and triggers the counter rotating mandrel gyration drive. The gyrating mandrel delivers multiple compressions at high pressure to the rotating particle bed. High concentrations of energy are harnessed within a small active volume over short retention times. The combination of extraordinarily high power intensity and extreme compressive force results in primary compressive fracture and induced secondary tensile failure. The axially displaced rotation of the compression chamber effectively distributes the breakage forces throughout the particle bed. This paper covers open circuit, pilot trials on magnetite, perlite, garnet, marble and a copper/pyrite concentrate. Particular emphasis is placed on the extraordinary results achieved with trials on zircon and highly refractory fly ash. The extreme duties were deliberately chosen to demonstrate the crusher’s application scope and potential to impact capital operating and maintenance costs as the technology matures. Super-fine crushing, once considered impracticable has the potential to offer compelling options for the generation of ultra-fine products.

Jan 1, 2014

By Tom Leistner, Urs A. Peuker, Martin Rudolph

"It is well known, that for conventional froth flotation techniques the processing of ultrafine mineral particles is generally inefficient and results in rather low-grade concentrates and relatively high losses of valuable minerals. Therefore, the investigation of other possible methods, which can selectively separate such fine particle systems effectively, is of considerable interest. In this study, the application of two-liquid flotation, a flotation-related process using oil droplets instead of air bubbles, is investigated as a possible processing strategy for the separation of ultrafine particle systems. The investigation involves the testing of the two-liquid flotation technique as simple laboratory-scale batch trials and moreover, the up-scaling to a semi-continuous process by using a modified lab scale flotation column. Magnetite and quartz particles, with particle sizes below 10 µm respectively, as academic mineral mixture and iso-octane and water as the two immiscible liquid phases are chosen for the experiments. To manipulate the wettability of the magnetite particles as well as the interfacial tension of the oil/water interfaces, surface active reagents of fatty acid basis are introduced in the system. The selectivity of the process is characterized by determining the removal of magnetite particles from the aqueous suspension through selective accumulation at the oil/water interface or extraction into the oil phase, respectively. Operational parameters including pH of the aqueous suspension, additional electrolyte addition and surfactant type as well as dosage are varied in order to maximize the efficiency and stability of the process."

Jan 1, 2014

By P. Banerjee, P. Dash, S. Sriramoju, A. Suresh, R. Lingam, T. Ray

"One single property that influences the quality and market value of coal to the maximum extent is the ash content. The lower the coal ash higher is the energy utilization and potential for different applications. Even though Indian coal washeries aspire to produce coal with low ash, the intimate distribution pattern of ash bearing minerals in the coal matrix becomes the real bottleneck, as it brings down the clean coal yield to the impractical value. Because of this fact, most of the Indian washeries are operated to produce coal with 14-15% ash content at the yield of around 40%. In this context, with an objective to produce low ash coal at higher yield, a novel chemical beneficiation route has been explored to demineralize the high ash containing Indian coals. In this present work, the production of low ash clean coal from high ash Indian coals using chemical leaching process has been studied at pilot plant level. The leaching process parameters such as reaction temperature, reagent concentration, reaction time, coal-liquid ratio and agitator speed have been optimized for the flotation tailings sample from a captive washery of Tata Steel. The results obtained show that 67% demineralization could be achieved in a single stage of leaching process with a product yield of more than 65%. For further demineralization, multistage leaching was carried out and the results showed that 75-85% demineralization could be achieved with significant reduction in alumina to silica ratio. Additionally, the phosphorus content is also significantly reduced from 0.20 % to 0.022 %. Further, it is interesting to note that there is no increment of sodium content in the product coal after chemical treatment."

Jan 1, 2014

By Yi-jun Cao, Jin-cai Ran, Guo-sheng Li, Jiong-tian Liu, Li-jun Deng, Shu-lei Li

A fly ash sample from a power station in Guangdong province has been characterized by size separation, X-ray diffraction, contact angle measurements and X-ray Fluorescence. The ash sample had a loss-on-ignition (LOI) (%) of 15.54% and a large proportion of the unburned carbon was distributed in the +74 µm and -20 µm fractions. Contact angle measurements suggested that the removal of unburned carbon from the fly ash using flotation would present some challenges. The effects of various operating variables on the removal rate of unburned carbon (RUC) (%) and (LOI) (%) were determined using a cyclonic-static micro bubble flotation column (FCSMC). Within the range studied, the optimum diesel oil dosage was 1200 g/t, abies oil (frother) dosage was 600 g/t, pulp density was 20%, superficial gas velocity was 1.4 cm/s and circulating pressure was 0.20Mpa. Column flotation tests indicated that the FCSMC method a viable and effective separation process for removing the unburned carbon from the fly ash. Under the optimized conditions, a clean ash with 2.13% LOI and 94.21% RUC was obtained.

Jan 1, 2014

By Xiaoping Xu, Tiansong Dong, Guosheng Wang

"Jianfengpo tin ore is located in Jiangxi Province, China. The cassiterite is fine and dispersed. It is hard to separate marmatite from a variety of sulfide minerals. Because the iron-containing sulfide minerals including pyrrhotite, pyrite and chalcopyrite are detrimental to the improvement of the grade of zinc concentrate. Besides, the presence of the iron oxides and ferro-carbonate minerals results in the difficult beneficiation of tin. Therefore, Jianfengpo tin ore is a kind of refractory cassiterite polymetallic sulfide ore. According to the properties of Jianfengpo tin ore, the technology process of "Sulphide ore preflotation-Bulk flotation of sulphur and zinc-Separation of sulphur and zinc -Magnetic separation-Gravity concentration" was developed to recover the valuable materials including marmatite, pyrite, magnetite, cassiterite and indium comprehensively. For the feed ore containing 0.87% Sn and 0.70% Zn, a zinc concentrate of 44.56% Zn with a recovery of 69.10%, a high-grade tin concentrate of 54.38% Sn with a recovery of 53.03% and a low-grade tin concentrate of 6.54% Sn with a recovery of 1.25% can be achieved in the batch flotation tests. In the industrial tests, for the feeding which contains 0.55% Sn and 0.65% Zn, the tin concentrate of 49.10% Sn with a recovery of 48.52% as well as the zinc concentrate of 45.11% Zn with a recovery of 60.10% can be produced. Thus some pyrite and magnetite concentrate are recovered as well. So Zinc, tin, sulphur and iron ores are recovered effectively by the technology."

Jan 1, 2014

By Sebastian Fredes, Williams Calderon, Mauricio Toledo, Gonzalo Montes-Atenas

The influence of the temperature on leaching kinetics of copper-bearing minerals has been widely acknowledged: the leaching of copper oxide ores is generally described as exothermic reactions while copper sulfide ores are associated with endothermic reactions. Reports studying the influence of temperature on leaching kinetics at laboratory scale frequently involve the implementation of either fully flooded isothermal systems or jacketed column setups. Nevertheless, at industrial scale controlling or monitoring the temperature or temperature changes is almost impractical. In fact, leaching process is usually a large tonnage operation and changing the temperature of vast amounts of material would require an enormous amount of energy and highly specific heat transfer equipment. Preliminary computations on the amount of energy required to increase the temperature of a heap or dump in 1°C indicates that it would be impossible to find an energy source able to accomplish the task. In order to provide a solution to this matter it is suggested to create an energy managing protocol (EMP) that permits heat up or down the porous body locally taking advantage from the temperature gradients and from the reactivity of different regions within the material as a function of the leaching cycles. The aim of this study is to evaluate different heat transfer regimes in a 1 ton pilot column leach operation. It was found that best results of copper recovery are obtained when heating up the column in horizontal bands starting from the top of the column moving downwards as the leach cycle evolves. The system is expected to be suitable for industrial applications, but further development of the technique is required, particularly in the design of the heat transfer dispositive.

Jan 1, 2014

"The thiosulfate leaching process developed by Barrick to treat sulfidic high preg-robbing gold ores uses calcium thiosulfate as the leaching reagent for ores pre-treated by pressure oxidation, resin for gold recovery with sulfite/trithionate elution and reverse osmosis as a means of reagent recovery. A large portion of the research that led to the development of the technology was based on previous studies completed by different groups over the years, mainly focused on the ammonium thiosulfate system. Operational limitations in the use of the ammonia-containing recycled water in the pressure oxidation circuit were some of the main drivers for the change from ammonium to calcium thiosulfate for the development of the industrial scale process. One of the main aspects for successful gold extraction and recovery in the thiosulfate system is the pseudo-equilibrium reactions that drive distribution of the different gold species (in solids, solution and on resin) in the system. Previous studies have been focused on the thiosulfate reactions and equilibrium constants for the oxysulfur ions (thiosulfate, trithionate, tetrathionate). However, the literature around the effects of the different metal-oxysulfur complexes (Cu and Hg complexes) that form when the ore is in contact with the leaching reagents, and the related effects on stability of the gold complex is limited. The main changes in the gold complex chemistry and stability in the calcium thiosulfate system as compared to the ammonium and sodium equivalents, as well as related effects on gold recoveries, were investigated in the presence of different types of double refractory ores. INTRODUCTION Barrick has developed a thiosulfate leaching process to treat double refractory gold ores, by combining the use of acidic and alkaline autoclave pre-treatment with thiosulfate resin-in-leach (RIL). The process currently in operation at the Goldstrike mine (the TCM process), uses calcium thiosulfate as the leaching reagent, resin for gold recovery with sulfite/trithionate elution and reverse osmosis as a mean of reagent recycle. The main feed to the process plant is highly preg-robbing sulfidic ore from Goldstrike’s open pit. Prior to feeding the pressure oxidation circuit, the ore is processed through the crushing and grinding circuits and treated in preparation for acid or alkaline autoclave processing (POX)."

Jan 1, 2018

By Matt Kilburn, Liming Lu, Steve Suthers, Alexander Edenton, Rodney Smyth, Matt Adam

"Magnetite concentrate is naturally good for pelletising. However, due to the depletion of reserves of traditional high grade hematite iron ore worldwide, the usage of magnetite concentrate in sintering is expected to increase substantially. Magnetite concentrate is typically high in Fe grade and releases extra heat when oxidised to hematite. This will not only improve the quality of agglomerates produced, but also have a potential beneficial impact on the fuel consumption of the agglomeration process. There are an increasing number of magnetite projects currently being considered and developed. However the concentrates from some of these projects are too coarse as pellet feeds and much finer and denser than normal sinter feeds. Accordingly, special strategies are required in order to utilise the coarse magnetite concentrates at high proportions in pelletising and sintering. This paper discusses various raw material preparation technologies and blending optimization methods demonstrated to be effective for improving the sintering and pelletising performance of coarse magnetite concentrates. Pre-granulation and addition of binders, such as hydrated lime, were found to be particularly efficient in recovering the sintering productivity of sinter blends containing magnetite concentrates. In pelletising, HPGR (High Pressure Grinding Rolls) grinding enabled production of good quality pellets from 100% magnetite concentrates and optimized blends containing up to 70% magnetite concentrates also formed good pellets.INTRODUCTION Magnetite concentrates are often used as feed materials for pellet plants or sinter plants depending on their grades and grain sizes. To achieve the required quality of green and fired pellets, the concentrates often need to be ground very fine (80% passing 38- 45 m), which inevitably consumes a great amount of energy. Therefore, efficient grinding processes are required to reduce the amount of energy consumption needed to achieve the sizing and chemical specification of pellet feeds. The use of magnetite concentrates in sintering has the potential to improve sinter chemistry, which is deteriorating over time due to the slowly decreasing grade of direct shipping iron ores around the world (Yang and Mathews, 1997; Yang and Witchard, 1998, Yang and Davis, 1999; Yang 2005). However, methods are required to allow the utilisation of high levels of concentrates in sintering while maintaining productivity and sinter quality (Han and Lu, 2017)."

Jan 1, 2018

By Venkataramana Runkana, Shantanu Maheshwari

As the world reserves of high quality ores are getting depleted at a rate higher than ever, the liberation of valuable minerals from low grade ores is becoming more and more relevant and imperative. But, liberation of minerals from low grade ores requires grinding of ore to extremely fine sizes. High energy milling in a planetary ball mill is one such option where one can produce particles in the nano-meter range. Although planetary mill is employed extensively for ultrafine grinding, dynamics of grinding inside the mill is not fully understood because of the dependency of grinding kinetics on many interconnected phenomena like collisions between media, particles and wall, time dependent rheology, adsorption and desorption of dispersant, abrasion of media, agglomeration of particles, etc. It was well articulated in literature that media motion and number of media collisions have strong effect on grinding kinetics and final product size distribution. Simulations were carried out using the discrete element method (DEM) to compare the performance of a planetary mill with a ball mill, with and without lifters, in terms of impact energy and number of collisions and it was found that number of collisions is considerably high in the planetary mill. The high number of collisions might be the reason for production of ultrafine particles in the planetary mill. We have also fitted a population balance model (PBM) to experimental data from a laboratory scale planetary mill for prediction of particle size distribution. Unlike previous models, we have incorporated functional forms for the selection function and the breakage distribution function so that the number of parameters in the PBM is just five. The predicted product particle size distributions at different grinding times are in reasonably good agreement with experimental data.

Jan 1, 2014