Search Documents

By V. Dementiev

Pyrite cinders is a complex raw material, in which the valuable metals are: Au(2.04 g/t), Ag(35.0 g/t), Cu(0.38%), Zn(1.1%) and Fe(56.0%). In this case high costs for mining and ore processing are not required. The hydrometallurgical treatment of pyrite cinders using thiourea, sulfite and cyanide solutions are examined in this paper. It was found that thiourea leaching is ineffective due to high consumption of thiourea and sulfuric acid. The cyanidation on pyrite cinders was conducted. Various options of the preparation of the products for the subsequent cyanidation have been examined. The tests on cyanidation process optimization were conducted. The effectiveness of these cementation methods by metallic iron or extraction for copper recovery from water phase has been shown. Zinc precipitation can be found in the form of carbonate. In order to recover noble metals from cyanide solutions, the cementation onto zinc dust was tested. The developed technology provides for recovery at 49-56%Au, 20-25%Ag, 22.5%Cu and 50%Zn during NaCN (1.4 kg/t) and CaO (6 kg/t) consumption. The results of pilot plant testing are the basis for technical regulations in order to design a pyrite cinders treatment plant. The technology has been examined in pilot-plant conditions. In this case the recovery of 54.5%Au, 45.3%Ag, 30%Cu and 49.9%Zn was achieved to provide saleable products. Keywords: pyrite cinders, thiourea leaching

Sep 1, 2012

By Martin Rudolph

"Flotation is without a doubt one of the major processes for the separation of fine minerals and it has been applied for more than a century. A key task of a successful flotation separation is to find the proper chemical treatment to selectively hydrophobize and thus float a certain mineral phase using molecules or ions referred to as collectors, depressants, regulators and frothers. Commonly floatability is determined by microflotation tests using the Hallimond tube with pure mineral phases. This method however requires the pure mineral phase which is very often not even taken from the same deposit which is going to be processed. In this paper we present a new approach to in-situ determine and even map the floatability of finely disseminated mineral phases within cross-sections of an ore. It is based on measuring hydrophobic effects using colloidal probe atomic force microscopy with a hydrophobic polystyrene probe based on force spectroscopy with a lateral resolution of only a few nanometers. Coupled confocal Raman spectroscopy on the same locality enables the identification of the mineral phase. We present the working principles of the method and show which signals in the force spectra characteristic for hydrophobic interactions can be used to define floatability and which can then be mapped as single quantities, e.g. jump-into-contact events due to nanobubble occurrence or parameters of the long range interaction curves most probably due to capillary effects. A finely grained silicate ore containing the valuable rare earth mineral eudialyte from southern Sweden as well as pure samples of magnetite are presented as substrates to demonstrate the capability of this new approach. This method will not only help to find the proper flotation chemistry but it can furthermore help in researching and unravelling problems of floatability within similar mineral phases."

Jan 1, 2014

By Reuter M. A., R. D. van der Weijden, W. F. C. van Wageningen

"Copper(II) can be recovered or removed from acidic copper sulfate solutions as cuprite or metallic copper powder by reduction with carbohydrates. The copper powder characteristics, such as size and shape of particles, determine the tendency to adhere to reactor walls and to agglomerate. In order to make this process suitable for a commercial scale pipe reactor, process conditions and the reactor configuration were varied in order to influence the copper characteristics in a positive way. The aim was to achieve proper particle throughput in the pipe reactor and to obtain a well defined copper powder.In this paper the effect of both, chemical and physical parameters on the shape and size of particles were systematically studied in a number of autoclave experiments. These parameters include mixing, Cu(II) concentration, pH, temperature, seeding, use of additives and reactor materials. Additionally, Monte Carlo simulations of copper growth inside a Kenics static mixer were made. Results show that the use of additives and the use of static mixers influence particle characteristics the most."

Jan 1, 2003

By K. C. Corin

It is well known that the grinding circuit plays a crucial role in flotation. The effect of pulp chemistry during grinding is often overlooked. It is believed that the surface properties of the minerals can be adjusted during flotation rather than during grinding. However, recent development in surface analysis techniques (TOF-SIMS, XPS, and AES etc.) have proven that the hydrophilic iron hydroxides formed at the mineral surface during grinding make it difficult for collector adsorption, which may result in poor grades and recoveries of the valuable minerals. This study investigated the effect of the pulp chemistry conditions during milling and the subsequent effects on flotation performance of an Nkomati ore. The results have shown that there was approximately 10 % increase in Ni recovery, when the ore was ground at a dissolved oxygen (DO) concentration of 0 ppm (DO-0) in comparison to no gas control during the grinding stage. However, when the pH was changed from 9 to 11, no gas control resulted in a 20 % decrease in the Ni recovery compared to only 5 % decrease in the Ni recovery at DO-0. A noteworthy observation is that controlling a combination of DO and pH during grinding is of critical importance for better floatability and selectivity for such a system. It also became clear from this study that the presence of oxygen is critical to the consumption of xanthate, which is consistent with the general literature. It has been established that grinding at lower DO levels/redox potentials (Eh) in the presence of xanthate significantly improves the flotation performance of the valuable minerals.

Sep 1, 2012

By Kari Niiranen, Andreas Fredriksson

LKAB (Luossavaara-Kiirunavaara AB) is operating iron ore mines, concentration plants and pelletizing plants in Northern Sweden. Geometallurgy, which combines geological and metallurgical information is not a new way of thinking at LKAB, but rather a revised and updated version of an old working process. A project called "Silica in the Mine" which started in 2007, was an important reason to set a new focus at the geometallurgy. The target of the project was to develop a simplified method in laboratory scale to predict SiO2 grade in the magnetite concentrate in Kiruna and further predict the physical properties of the crude ore with respect to processing characteristics. The connection between mineralogy and products properties have started to be even more vital and necessary to examine due to the future exploiting new iron ore deposits. Geometallurgy at LKAB can be described as a mental and strategic framework where the Research and Development department (R&D), and others within the organization of LKAB, aims towards the connection of the minerals-production-products. It could in its basics be called "research & development", but it must be clarified that changes have been made, mainly due to the development on the instrumental analysis side. LKAB’s idea is to work quite broad, with internal educations, an active working process in ongoing projects, together with external parties (such as universities), with several PhD-projects and an upgrading on the instrumental side at the LKAB Research & Development department. This paper is a summary about the concept Geometallurgy at LKAB and some of the actions within its framework.

Jan 1, 2014

By Andrew T. McBride, Malcolm S. Powell, Indresan Govender

"Current empirical Semi Autogneous Grinding (SAG) mill models contain assumptions concerning the amount of energy available for particle breakage, how this energy is distributed in the mill media and the rate at which the energy is transferred. Despite these assumptions the JK SAG model is highly functional with a proven track record. DEM provides a numerical framework to greatly improve on these assumptions that were necessary due to a lack of available input data.This paper identifies key outputs of the Discrete Element Method (DEM), such as energy spectra and impact probability distribution. It describes how they can be incorporated into current mill models utilising practical rock breakage data. The rate at which energy is transferred is shown to be dependent on particle position and mill rotational speed and not once per cycle as previously assumed. Based upon this an improved energy transfer methodology is presented. The fundamental outputs of the DEM are validated against experimental three-dimensional particle tracking data, so as to establish whether the DEM produces correct energy transfer predictions on the inter-particle level, which is crucial to this work. • Effective Experimental ValidationAn automated 3D tracking technique is employed to study the motion of plastic particles deep within the charge of a 142mm diameter experimental mill. A Biplanar Angioscope is used to film the mill with X-rays in two planes simultaneously at 50 frames/s, with a shutter speed of 1/3000s. A marked ball within the charge is tracked for over 2 minutes and the resulting digital images processed by a fully automated imaging technique, which locates the 3D coordinates of the particles to within 0.2mm. With over 250 circulations, this provides statistically rigorous and accurate data for verification in the numerical modelling of mills.A series of validation techniques have been developed to compare the experimental trajectory data with the outputs of both 2D and 3D DEM simulations. The techniques describe the shape of the charge and the particle motion within mill, allowing objective comparisons to be made of key features of the charge, such as the equilibrium surface and the centre-of-circulation."

Jan 1, 2003

By I. Blayda

The purpose of this work is to study and make comparative analysis of germanium extraction and related valuable components of the sublimates from the burning of domestic power coals (product 1) and germanium sulfide materials, which are a waste of lead-zinc production (product 2), by traditional chemical methods (distillation of germanium in the form of tetrachloride from raw and preliminary burning source) and by microbial bioleaching of sulfur-oxidizing bacteria. The dependence of the germanium extraction by chemical methods from phase composition of the initial raw materials was installed. The germanium tetrachloride extraction from products 1 and 2 were 78.50 and 19.52%, respectively. Such difference in indexes on extraction, is caused by germanium confinement as concomitant trace component to the basic phases to carriers. The share of acid-non-soluble compounds (tetragonal modification GeO2 and silikogermanaties) in the product 1 account for 21.5 % of germanium. Ratio between acid-soluble and acid-not -soluble germanium forms are 19.52 and 80.48 %, respectively, in the product 2. Our experiments have shown, that implementation of restorative firing (with addition of 30-40 % carbon at 1150 0?) of sulfide product 2 considerably impacted on the extraction of germanium tetrachloride (91.76 %) in comparison with its low enough extraction at straight distillation of hydrochloric acid (19.52 %). The results are confirmed by a set of physical methods. The results of processing the same so-called hard phase?s material (product 2) with the help of microorganisms are presented. It Has been established, that selected strains of bacteria are capable of extracting from initial raw materials not only macro components (iron, zinc, lead, manganese, aluminum, nickel), but also micro impurity of rare metals (gallium, germanium, zirconium). It is important that these metals were not extracted by traditional chemical methods (with application of aggressive conditions and heats) independently of the phase composition of the source. Almost complete extractions of germanium in solution using sulfur-oxidizing bacteria take place in the first day of the process independently of the phase composition of the source and the type strain. The results have practical significance and can be the basis for developing a unified biotechnological method of technogenic waste processing with a purpose of their sterilization and detoxification with simultaneous obtaining concentrates of valuable metals. Keywords: germanium, extraction, sublimates, bioleaching, sulfur-oxidizing bacteria.

Sep 1, 2012

By Rintaro Hayashi

The enrichment of useful components from ores and/or wastes has become important with increasing recent worldwide resources demand and the amount of wastes generated from the urban mines, in order to establish real ?sound resource-cycle society? including the activity of resource exploitation. The first stage of the treatment in the process must be comminution and it is important to make good liberation among compositional phases in the targeted resources. Electrical disintegration (ED) is well known to make a selective breakage at phase boundary. However, the detailed mechanism of the phenomena is not clarified yet, in especial, on the influence of electrical properties of compositional materials on the liberation. This paper made a comparison between the liberation degrees of ED products and the results of electromagnetic field analysis using finite element method (FEM). In the experiments, we used several synthetic cement paste based samples in which mineral particles were dispersed to apply the ED, and in the electromagnetic field analysis, we calculated the charge density accumulated and the Maxwell stress at phase boundary. It was found, for highly insulating mineral samples, that higher breakdown voltage was necessary because electric charge was not easily accumulated at phase boundary but that higher liberation degree was obtained after the breakdown (ED). It was also found the tendency that higher liberation was observed for the samples which had higher maximum Maxwell stress calculated by the electromagnetic field analysis. From the results, the electrical charge and Maxwell stress induced at phase boundary could be driving forces of selective breakage. In addition, we also applied the ED to the printed circuit boards (PCBs) in order to concentrate miner rare metals, which were essential for producing electronic devices. It could be demonstrated that the devices installed on the PCB were easily detached from the board and that most of metal elements in the devices was exposed and liberated from the insulating plastic covers, which were broken in the ED, then, it is considered that the subsequent solid phase separation could be effective for concentrating such metal elements. Keywords: liberation, electromagnetic field analysis, printed circuit board, miner rare metal

Sep 1, 2012

By V. Z. Kozin, E. A. Bekchurina, P. S. Volkov, Yu. P. Morozov, A. S. Komlev

"The current sampling systems of ore flows or concentrates are based on the method of cross sections in point sampling and the method of scooping in reducing. The limited number of point samples in sampling and microsamples in reducing lead to big random and probable systematic errors. The paper defines the principles of sampling, which assure the absence of systematic errors and also provides calculation formulas of probable errors in sampling methods of cross and longitudinal sections as well as in samples preparation. The article sets the fundamental laws of sampling: the dependency of minimal mass of gross sample and number of point samples from mass of point sample in sampling from heterogeneous body; the dependency of a sample minimal mass from lumps’ size in preparation of carefully mixed samples; the dependency of point samples’ dispersion from duration of control period. The paper introduces the fundamental notions: lump variance; probable systematic error; methodical error. It also provides a solution of outstanding sample correct application in analysis results calculations. In application of automatic analyzers, mounted in material flows, the probable error connected with sampling, is calculated by the formulas for carefully mixed sampling bodies. The paper describes the developed and introduced sampling systems on the base of combined application of cross and longitudinal sections methods in sampling and preparation of samples. The advantages of this equipment are compactness, reliability, simplicity in service and operation, and for pulps it is adaptability in pipelines. Application of the developed equipment entirely excludes probable systematic error. The new systems of sampling and preparation of samples are introduced at 25 concentrating plants. Introduction of the developed systems at sampling balance points of concentrating plants allowed double reducing balance deficiency."

Jan 1, 2018

By D. Kosior

Influence of frothers (a-terpineol and n-octanol) concentration on kinetics of a three phase contact (TPC) formation by a bubble colliding with a hydrophobic surface (Teflon) of different roughness was studied using a high-speed camera (1040 frames per second). It was found that the Teflon surface roughness and the frother concentration strongly affected time of the TPC formation (tTPC) and time of drainage (tD) of the liquid film separating the colliding bubble from the solid surfaces. With increasing Teflon surface roughness, from ca 1 to 80 µm, the time of the TPC formation was shortened by over the order of magnitude, from ca 100 to a few milliseconds only. At low a-terpineol and n-octanol concentrations, thetTPC values were shorter than in distilled water due to lowering the bubble velocity in the frother presence and diminished bouncing of the colliding bubble. However, at high frothers concentrations the tTPC values were prolonged, despite that the bubble velocity was similar. The prolongation of the tTPC at high frother concentrations indicates that air (micro- and/or nano-bubbles) was present at the Teflon surfaces of different roughness. The mechanism of the tTPCprolongation at high frother dosage is described.

Sep 1, 2012

By T. Sun, J. Kou, C. Sun, D. Gong

"HPGRs (high pressure grinding rollers) have demonstrated higher energy efficiency than conventional comminution equipment due to their application of particle-bed breakage mechanism. In the past decades, a large number of studies have been conducted to understand the characteristics of particle-bed breakage, however, few of them concerned the difference between single-particle and particle-bed breakage in compression comminution. This comparison is able to demonstrate possible advantages of particle-bed against single-particle in a breakage event due to the isolation of the effect of force loading mechanism. The present study investigated progeny fragment size and energy efficiency of these two breakage methods at variable energy inputs and particle sizes. The results show that at low energy inputs of around 0.25 kWh/t, the numbers of fines resulting from the two breakage methods are very similar. However, at higher energy inputs of around 1.0 or 2.0 kWh/t, particle-bed breakage generated significantly more fines. From the perspective of newly generated surface energy, particle-bed breakage is obviously more energy efficient than single-particle breakage at energy inputs between 1.0 and 2.0 kWh/t. It was also found that HPGRs demonstrate high energy utilization rate in generating new surface energy within their typical range of specific energy input. INTRODUCTION Rock comminution is an important and energy-intensive process in mining operations. Nowadays, decreasing head grade and mineral liberation size of ore deposits greatly increase the energy cost of comminution process. HPGRs have been successfully applied in the mining industry to improve the energy performance of comminution circuits. Typically, 10 to 30% of energy saving can be achieved due to the application of HPGR (Wang et al., 2013; Casteel, 2005; Günter et al., 1996)."

Jan 1, 2018

By R. X. Li

The overall flow-sheet of producing chromium (III) sulfate is described in this paper. The suitable conditions of each process such as sintering, leaching, aluminum removal, reduction, and de-composition conditions were experimentally studied. The results show it is reasonable to produce chromium (III) sulfate with the flow-sheet pointed out in this research work. The final product is Cr2(SO4)3 solution contained 150~250g/L Cr.

Jan 1, 2014

The flotation of nickel sulphide minerals is normally difficult in the presence of serpentine minerals due to the coating of serpentine particles on the nickel mineral surface. To improve the flotation, dispersants such as polyphosphate and carboxy methyl cellulose are normally used to remove the slime coating. However, in the flotation using high ionic strength process water, these dispersants are invalid due to their ionic nature. In this study, a new type of non-ionic dispersants, Pluronic triblock copolymers were examined with an objective of improving the flotation of ultrafine pentlandite (a nickel sulphide mineral) in the presence of lizardite (a serpentine mineral) in saline water. Three Pluronic triblock copolymers varying in solubility and hydrophile-lipophile balance (HLB) values were studied by flotation tests, settling tests and froth measurement. It was found that two of the copolymers improved pentlandite flotation against lizardite, and one copolymer deteriorated the flotation. The effect of Pluronic triblock copolymers on the flotation was actually linked to their dispersibility and foamability, which were governed by their physical properties. The two copolymers with a higher solubility or HLB value produced more stable mineral suspensions and more stable froth in the flotation resulting in better nickel grade and recovery in both rougher and cleaner flotation. Keywords: ultrafine particle, flotation, slime coating, dispersion, saline water, triblock copolymers

Sep 1, 2012

By Genrich A. Denisov

Principles of ecologically friendly geo-technologies construction are formulated on the basis of the works of the leading scientists in the field of rational processing of mineral resources of the Russian Academy of Sciences. One of these concepts is a new direction in rotational disintegration of mineral and technogenic raw material with the purpose of effective subsequent enrichment. A large amount of practical experience has been accumulated in the industry on selective destruction by application of vibrational method on initial material with consideration of its physical-mechanical properties and mineral structure. This method is successfully realised in a conic inertial pulverisation devices constructed by Mekhanobr Institute (St. Petersburg). A new construction of conical-inertial pulverisation with a modification of disintegration force has been developed recently at Mekhanobr Institute. It allows, in some cases, to increase selectivity of subdivision and to avoid over-disintegration. Advantages of “wet” subdivision methods in conic inertial disintegration devices are proved. The efficiency of such subdivision can be increased due to rational use of the phenomenon of a dislocation-dynamic diffusion. Its advantage is proved by the effect on disintegrated material by frequency-modulated variable electrical fields of low power. It was shown in industrial conditions, that the productivity of the spherical mill can be increased by 10 %, and that it also prevents ecologically harmful surface active substances (SAS) in milling zone and it reduces the dust content in the air. The techniques of tentative estimation of efficiency of various proceedings technogenic materials and their classification are created. The scientific fundaments of rational, ecologically friendly technology of processing and regeneration of various kinds of technogenic raw material are developed. A number of effective technologies on processing of wastes is developed and inculcated in concentration factories and metallurgical factories.

Jan 1, 2003

By Santiago Garcia, Dariusz Lelinski, Devan Govender, Tyson Baker, Mads Jespersen

"In recent years, the scale-up of mechanical flotation machines has been attempted with greater frequency. In contrast, the development of rotor-stator designs has been subject to greater inertia. The rotor-stator components are integral to the operation of mechanical flotation machines, responsible for the key physical processes of solids suspension, gas dispersion and energy dissipation. Design modifications are predicated upon the dual purpose of meeting customer needs while achieving metallurgical performance objectives. Accomplishing the latter is a rigorous undertaking, typically involving the sequential application of fluid dynamics principles, prototyping, smaller-scale research screening studies and larger-scale development projects. This industrial evaluation details the final stages of the forced-air rotor-stator development process using a double-refractory Carlin-type gold ore. A bypass stream of the primary rougher feed was further classified into cyclone underflow and overflow products. Four rotor-stator treatments were evaluated using parallel flotation rows coupled with a randomized statistical design. Only two treatments are compared in this initial assessment. Metallurgical responses were measured as a function of the random variation of key machine factors. Machine characterization measurements complemented the analysis of flotation performance indicators."

Jan 1, 2014

By Yuri L. Nikolaev

The treatment of placer gold with fine gold, associated with gold-bearing sulfide minerals, heavy minerals and oxidized minerals such as manganowolframite (gubnerite) is not an easy task. In this case, this complex material cannot be treated using physical separation methods such as deep concentration and finishing, magnetic separation and solvent extraction. This technology is usually employed in gold washings finishing plant. The easiest way to recover precious metals in the form of an easy-to-sample saleable product is metallurgical treatment. This paper describes the application of pyrometallurgical processes with oxidative roasting, re-cleaning of cinders (if required) and ore-thermal smelting for producing gold bullion. Hydrometallurgical treatment of slags as an additional operation is recommended in order to maximize recovery of valuable metals. After this treatment, a barren leaching cake rich in PGM can be sold in the market. PGM can be collected as gold-silver alloy during smelting which allows the phase formation of polymetallic matte due to specific composition of fluxes. The PGM are then in the form of saleable gold bullions in the refinery.

Sep 1, 2012

By S. V. Petrov

Oxidised ores possess a significant share among raw materials which are treated by traditional plant technology. As usual, the chemical composition of these ores is rather simple. They can be treated by standard cyanidation. In this case, the resulting wastes have an alkaline reaction. Their toxicity (in case of ROM ores treatment) is mainly due to the presence cyanides and thicyanades. The tails are dexotified before disposal. However, chemical reagents used cannot provide a complete removal of toxic matters. In this case, this disposal poses a real problem because these tails contain a significant amount of CN and SCN and their behavior during a long disposal should be studied. A sample with a simple composition taken from cyanidation tails was studied. The sample presents itself the quartz low-grade sulfide gold-bearing ore. Sulfide sulfur content is 0.15 per cent,and heavy metals content is 0.023 per cent. Method of testing is described further. The samples were tested under moderate and subarctic climates based on the difference in temperature, moisture and the degree of oxygen saturation of air. The pH of water extract, which was prepared using distilled water, was also determined besides measuring the concentration of cyanides and thiocyanates. This demonstrates the stability of sulfide-bearing minerals in the disposed tails. The tests time was 820 days. It was found that the alkalinity of the samples tends to lower under oxygen-containing conditions in proportion to temperature increasing. Under conditions without oxygen, the pH lowering is minimal. Mineralogical and chemical properties of the ore material give positive alkaline balance during testing. The solid sample contains enough alkaline agents to compensate dangerous to the environment reactions of sulfides oxidation.pH value maintaining under alkaline conditions witnesses to the possibility of a safe disposal of this tails type. The largest amount of cyanide is removed under acid-containing conditions at positive temperatures. The higher the temperature is, the more intensive destruction is. At the moment, of finishing the tests at 20ºC temperature, the residual concentration of CN- was 0.06-0.10 mg/L, at 4ºC, the residual concentration of CN- was 0.2-0.3 mg/L and at -18ºC was 0.4-0.6 mg/L. Under conditions with the lack of oxygen, cyanides can be removed within the first 200 days. Then, this process fully stops. A stabilized cyanides concentration is 3.0-4.0 mg/L. The presence of sulfides increases the content of cyanides at the initial stage of testing. Then, the concentration of SCN at the temperatures above 0ºC decreases rapidly under oxygen-containing conditions. At the rise of temperature, a narrowing of peak at the curve and an increase of the destruction process are observed. At the end of testing, the concentration of thiocyanates in the moisture of wastes was 0.2-0.3 mg/L at the temperature of 20ºC and 0.5-0.6 mg/L at the temperature of 4ºC, respectively. The concentration of thiocyanates contained in a frozen sample and media which have the lack of oxygen stabilizes at a certain level owing to sulfides and does not practically change further. It was found that detoxification of oxidized cyanidation tailings with a simple composition which were disposed as filtration cakes can be possible. In this case, the concentration of cyanide in the moisture of disposed wastes can have a close value or equal to actual concentration during cyanidation. In order to meet the requirements of high ecological safety standards and successful detoxification process of toxic compounds in the tails under the action of natural factors, the conditions of air aeration with oxygen for the whole volume of tails are required. Keywords: cyanides, thiocyanates, storage, detoxification, flotation cakes

Sep 1, 2012

By Narasimha Mangadoddy

The complex nature of multi-phase flow in dense medium cyclones has restricted plant operators and designers to rely on empirical equations for predicting the performance. A number of empirical cyclone models have been developed in the past (Wood, 1990; Dunglison, 2002). In recent years, this subject has been broached with computational fluid dynamics (CFD). Most of the CFD models have not considered the correct rheological behavior of magnetite medium while simulating the medium segregation inside the cyclone. These models mostly predict excessive underflow volumetric flow rates. In this paper simulations of magnetite medium in a dense medium cyclone, were conducted in FLUENT where the particle phases were simulated using the modified Mixture model. The turbulence was resolved using Large Eddy Simulation (LES) model. The rheological behavior of medium was considered in the form of Granular viscosity, Newtonian and Non-Newtonian models corrected with particle loadings and fraction of ultrafines. Multi-phase simulations using granular viscosity option although predict the overall split product medium densities reasonably close to experiments, the mixture viscosity values are restricted to substantially lower values, similar to water viscosity. Simulations using Newtonian viscosity model corrected with particle loading, and fine fraction below 53µm size is predicting overall mixture viscosity levels well over water viscosity levels, but under predicting the under flow the underflow medium density. Multi-phase simulations using Non-Newtonian Herschel-Buckley model, calibrated for superfine magnetite medium measured viscosities, is closely predicting the medium segregation with gamma ray tomography data. Overall predicted product medium densities, underflow volume split are close to the experimental data. This model is can be further used to simulate coal portioning and hence in developing new designs.

Sep 1, 2012

By I. Zh. Bunin, G. K. Khachatryan, N. E. Anashkina

For optimization of diamond processing technology the influence of nanosecond high voltage pulses on mechanical and technological properties of diamond crystals and kimberlite rock-forming minerals (calcite, olivine, serpentine) was investigated. Using methods of Fourier Transform Infrared Spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), microscopy and mikrohardness measurement the changes of structural, physic-chemical surface properties, and microhardness of minerals as the result of impacts, was studied. Non-thermal impacts caused a decrease of kimberlite rock-forming minerals microhardness in general to 40-66% as the result of surface microstructure destruction which is caused by formation of micro cracks, traces of surface breakdown and other defects. At the same time, the pulse energy impact on natural diamonds led to formation of B2 type crystal lattice microsift defects, elevated concentration of which increases the hardness properties of crystals. The obtained result indicates possibility of applying pulsed energy effects to improve the softening efficiency of diamond-bearing kimberlites rock-forming minerals without damaging the diamond crystals and ensuring their preservation by the subsequent grinding of ores. By IR and X-ray photoelectron spectroscopy revealed that processing by hight voltage pulses causes a change of natural and synthetic diamonds surface functional cover composition. Short-term exposure (~ 10 - 30) leads to detachment and partial destruction of secondary phases mineral films on the surface of natural technical diamonds, increasing floatability and hydrophobicity of crystals. However, with increasing duration of treatment (~ 30 - 150) occurs surface hydroxylation (found by XPS for synthetic diamonds), as a result of diamond surface layer oxidation. The effect of increasing the natural diamonds flotation activity by 14% (from 47% to 61%) was experimentally established as a result of processing diamond crystals with nanosecond pulses (~ 10-50 sec), which indicates the principal possibility of using pulsed energy impacts to intensify the diamond flotation during processing diamond-bearing kimberlites.

Jan 1, 2018

By Haghi. Hamed, Javad Vazifeh Mehrabani, Mehdi Sedigh

In this investigation, the possibility of physical separation methods such as attrition scrubbing, hydro-cycloning and also reverse flotation were investigated for silica and calcite removal from relatively low grade kaolin. The head sample was provided by the Iran China Clay Company and the major oxides contained in the head sample were Al2O3, SiO2, CaO and Fe2O3 with grades of 15.07%, 71.05%, 4.35% and 0.52% respectively. The liberation degree of calcite and iron impurities from kaolin particles were over 80% for particles finer than 210µm and 53µm respectively. Attrition scrubbing tests were carried out with scrubber cell of the conventional Denver flotation cell model D-12. Laboratory scale hydro cyclone was applied for the beneficiation of kaolin. Attrition scrubbing tests with control screen of 106µm did not achieve the desirable yield for purification of this kaolin sample, but hydro cyclone experiments resulted in better results. Hydro cyclone with 2.54 cm diameter used and the only variable was the cyclone inlet pressure ranging from 68.65kPa to 98.07kPa. The best inlet pressure was found to be 68.65kPa. Based on the optimized condition, Al2O3 and CaO amount in the hydro-cyclone overflow was 23% and 1.47% respectively. However weight recovery of the overflow in each cyclone experiment was less than 30% and multi stages of hydro-cyclones would have to be applied for higher weight recovery and better yield. All of the flotation tests were carried out in the conventional Denver flotation cell model D-12. Reverse floatation tests for calcite removal were carried out under alkali pH based on full factorial design of variables in 2 levels including one center point. The three parameters tested were collector dosage (gr/ton), pH and depressant dosage (gr/ton). The collected data from flotation tests were analyzed and optimized collector and depressant dosage were 1000 gr/ton and optimized pH was 8.5. Under the above mentioned conditions, calcite removal was about 75% and CaO content in the final product was reduced from 4.35% to 1.33%. However calcite removal will increase to more than 83% if the feed particle size in flotation tests is reduced from 210µm to finer than 53µm. Finally after optimization, the best working condition and possible flow sheet were developed.

Jan 1, 2014