Search Documents

By Cees van Rhee, Rudy Helmons

INTRODUCTION Seafloor Massive Sulphides are typically found near the oceanic ridges at larger water depths (>1km). The physical properties of SMS, as shown in table 1, are comparable to the properties of weak rock. One of the technical challenges to enable extraction from these locations is the cutting or excavation process. Experiments have shown that the energy needed to excavate the material may increase with water depth (Alvarez Grima et al. 2015). Besides that, it is demonstrated that rock that fails brittle in atmospheric conditions can fail more or less in a plastic fashion when present in a high pressure environment, as would be the case at large water depths. The goal of this research is to identify the physics of the cutting process and to develop this into a model in which the effect of hydrostatic and pore pressures is included. The cutting of rock is initiated by pressing a tool into the rock. As a result, at the tip of the tool a high compressive pressure occurs, which leads to the formation of a crushed zone. Depending on the shape of the tool and the cutting depth, shear failures might emanate from the crushed zone, which will eventually expand as tensile fractures that can reach to the free rock surface. Through this process intact rock will be disintegrated to a granular medium. For an overview of the process (figure 1). Additionally, the presence of water in the pores of and surrounding the rock influences the cutting process through drainage effects. The most relevant effects are weakening when compaction and strengthening when dilation occurs in shearing and tension. Deformation of the rock causes the pore volume to change, resulting in a under or over pressure. As a result, the pore fluid needs to flow. The magnitude of the potential under pressure is limited through cavitation of the pore fluid, limiting further reduction of the pore pressure (figure 2). The drainage effects cause the rock cutting process in a submerged environment to show a stronger dependency of both the hydrostatic pressure as well as the deformation rate (figure 3).

Jan 1, 2018

By C. L. Mardock

The U. S. Bureau of Mines participated in a two-year joint State of Oregon/Department of Interior Placer Task Force study on the economic and environmental aspects of Oregon's marine placer deposits. The effort culminated in a research cruise off the southwest coast of Oregon to investigate the geological and biological characteristics of the continental shelf deposits. The Bureau's role was to collect and study the placer material off the continental shelf and to determine its strategic potential and significance. In-depth characterization of the sediments by optical and electron microscopy verify that the placer material from Cape Blanco contains up to 3 pct ilmenite, 0.5 pct chromite, and small amounts of zircon and gold. However, harsh sea conditions and equipment failures prevented sampling below a four-foot depth at the Cape Blanco site. Results to date indicate that the deposits sampled off the southwest coast of Oregon do not represent a significant source of strategic minerals. However, further study of the deeper sediments off Cape Blanco may uncover significant concentrations of chromite. This presentation encompasses the site geology, the geophysical and biological activities of the expedition, and the results of the Bureau's mineralogical and chemical investigation. The combined findings of the Bureau and other Task Force agencies have provided information needed to expand the country's limited knowledge of marine mineral resources and has assisted state and federal agencies in the formulation of offshore mineral policies.

Jan 1, 1991

By Dorothy B. Niell, O&apos

In its first three years of operations, the in-house programs of the continental Shelf Division of the Marine Minerals Technology Center (MMTC/CSD) have focused on the development of drill systems - technology and the improvement of techniques and applications of reconnaissance methods to marine mineral deposit characterization. Many of the technological advances made to date have been in direct response to specific requests from industry for drill systems needs, and from federal and state agencies seeking technical support for various research efforts. These cooperative programs have proven to be an extremely efficient and effective way for the MMTC to achieve some of the main program goals that were established for the organization at the outset: primarily, to encourage and assist U.S. industry in marine minerals research activities and to encourage cooperative work among research institutions, government agencies, and industry. The primary achievements of the MMTC/CSD to date include the development of the Remote Placer Drill System for rapid reconnaissance drilling of precious metal placer deposits (including both pneumatic prototype and hydraulic production

Jan 1, 1991

By Jan Magne Markussen

The aim of the paper is to analyze the viability of commercial exploitation of polymetallic nodules, the time aspect for exploitation and the probable organization of commercial projects. METHOD My methodological point of departure is to view the various factors in context, and to differentiate between the various groups of actors. This involves taking as my starting point the interaction that exists between economics, technology, politics, law, the environment, and even psychology and ideology, and acknowledge that the various actors may well have differing motives for their engagement.

Jan 1, 1992

By David Heydon

The big money is backing both manganese nodules and manganese crusts as the most likely deep ocean mining development by 2010, but seafloor massive sulphides of copper/gold/zinc offer an alternative bet for a start-up by 2010. A study of the ?form guide? or comparison of these resources provides direction on which resources are economic candidates for commercial deep ocean mining development by 2010. This paper covers the commercial and technical issues of exploration, resource definition, drilling/sampling, sea bed mining options, mine plans, environmental issues, legal tenure and capital and operating costs (i.e., profitability) of these two mineral types. Nautilus Minerals has just completed a pre-feasibility engineering study of mining sea floor massive copper/gold/zinc sulphides at 2,000 m depth. The Nautilus study reviewed a range of mining and lifting options, settling on tracked continuous drum cutter miners to produce 2 million tons per annum of high grade ore. Capital costs are shown to be at least 30% lower than a land based copper mine of the same production capacity. Likewise 75% of world?s copper would be produced at a higher operating cost that the proposed seafloor mine. This paper then draws on the Nautilus study for comparison with earlier feasibility studies by others on manganese nodule mining to predict the likely directions in deep ocean mining to 2010.

Jan 1, 2004

By Jon Machin

?ORE? is defined as ?mineral/s that can be mined at a profit?. So, what is ORE at 2,000 m water depth? Is it 5% Copper or 1.8% Nickel/Cobalt? One of the key factors that determine what is ORE, profitable or not, is the cost of mining and extraction. Therefore a determination of ORE requires a commercial and technical appreciation of both sea bed mining equipment and mining options. Perry Slingsby Systems (PSS) have built more remotely operated submarine work vehicles, including 900HP trenching machines, than any other company. With Nautilus Minerals, PSS have been studying a range of deep ocean mining solutions. This paper discusses the commercial and technical issues of various extraction techniques applicable to deep ocean mining from 1,500 m to 5,000 m water depth. Issues such as the rate of extraction, (i.e. tons per hour) is a key economic component and is often constrained by the design and horsepower of the miner. Likewise the design itself of the mining machine and cutting heads can determine the size of material produced which impacts on methods of lifting the ore to surface. Issues such as overburden, sea floor conditions, style of mineralization and physical properties of the ore, obviously affect the selection of appropriate mining machine configuration.

Jan 1, 2004

By Stanley R. Riggs

Onslow Bay is a broad, shallow, high-energy shelf system bounded by the Cape Lookout and Frying Pan shoals. It is generally a sediment-starved shelf system dominated by hardbottoms with a scattered and discontinuous veneer of mobile Holocene sediments. Phosphate-rich beds of the Miocene Pungo River Formation crop out in a belt 150 km long and up to 50 km wide across the continental shelf in Onslow Bay, North Carolina. Previous research has demonstrated that a few of these beds contain vast quantities of potentially economic phosphate resources that occur in the surface and shallow subsurface sediments. Onslow Bay contains five phosphate-bearing beds predicted to include up to 20.7 billion tons of in-place phosphate concentrate with total sediment grades ranging up to 22.9% P2O5 and adjusted average concentrate grades of 29.8% P2O5. These phosphates are lithologically and chemically similar to phosphates currently being mined in the nearby Aurora phosphate district in North Carolina. Various lithologies of the Pungo River Formation and associated rock units of Oligocene and Quaternary age crop out on the sea floor to form extensive hardbottom habitats that dominate almost 100% of Onslow Bay. A large proportion of these hardbottoms appear to be sea floor deserts, whereas others are virtual oases with rich associations of benthic organisms. These important differences in benthic community structure appear to be greatly influenced by one or more of the following variables: 1) geologic framework (geologic formation, hardbottom composition, morphology, and spatial orientation relative to dominant currents and waves), 2) texture, movement, and accumulation of surface sediments, and 3) flow rates and chemical composition of discharged submarine groundwater.

Jan 1, 1992

By Amy Gartman

The interactions between hydrothermal fluids and seawater result in minerals that range in size from nano- to macro-scale and constrain mineral emplacement, whether in hydrothermal chimneys or metalliferous sediments. Although broad similarities exist, and sulfides are the most important component of seafloor massive sulfide deposits, the specific mineralogy, size and therefore reactivity of particles emitted varies between hydrothermal sites in the global ocean, and even at different sites within the same vent field. The oxidation of sulfide minerals results in one of the major impacts of terrestrial mining of volcanogenic massive sulfides as it creates acid mine drainage. At marine hydrothermal vents, the chimneys themselves, as well as the ‘black smoke’ begin to oxidize as soon as they are in contact with ocean water; the breaking of sulfide minerals during marine mining will expose further surface area to seawater and oxidation. Although the cold temperatures and circum- neutral pH result in oxidation proceeding less rapidly than in many terrestrial systems, there is limited data on the kinetics of sulfide oxidation in seawater. Here, the oxidation of sulfide minerals in seawater and the implications for marine mining will be discussed, with an emphasis on nano-ZnS and sphalerite, including reaction kinetics, processes, and oxidation products.

Jan 1, 2018

By V. Alexandrov

This paper presents the results of theoretical investigations of the energy requirements of the hydraulic lifting of mined materials from the seabed to the sea surface in the deep-sea mining of solid minerals such as manganese nodules in the Clarion-Clipperton region of the Pacific, situated on the sea floor in water depths of 4,500 m or more. The principal element of the developed underwater transport system is the Underwater Chamber, which is connected by flexible pipeline to a mining machine that gathers nodules from the seabed, mixes them with seawater, and feeds them into a flexible pipeline. In this paper, we discuss the question of the optimum water depth for placement of the Chamber, the interior of which is designed to maintain a 1-atmosphere pressure. We present a method for calculating this depth as it relates to the mechanical characteristics of solid particles, the shapes and size distributions of the particles, particle and slurry density, and other properties. These investigations were carried out in hydro-transport laboratory of the Saint-Petersburg Mining Institute and the hydraulic laboratory of Faculty Environmental Engineering in Wroclaw Agricultural University. KEY WORDS: deposit, nodule, flexible pipeline, pressure drop, concentration, hydromixture

Jan 1, 2005

By Hunsoo Choi

Internal textures of manganese nodules from Clarion-Clipperton zone of northeastern Pacific Ocean are classified into five textural zones: columnar-textured layered zone, cuspate-textured layered zone, cuspate-textured massive zone, cuspate-textured porous zone and massive- textured massive zone. Vernadite is the main constituent mineral in the columnar- and cuspate-textured layered zone. Buserite sometimes occurs in the cuspate-textured layered zone. The cuspate-textured massive zone is mainly composed of buserite. Todorokite is also associated with buserite in the massive-textured porous zone, where cuspates and globes are partially replaced by massive texture. In the massive-textured massive zone, todorokite, buserite and birnessite occur together. The analyzed elements of all zones are also classified into four elemental groups by the cluster analysis of correlation coefficients: Mn group, Cu-Ni-Mg group, Fe group and Si group. Mn group consists of Mn and K. Cu-Ni-Mg group consists of Cu, Ni, Zn, Mg and/or Ca, Na. Fe group consists of Fe, Co, Ti and/or Ca, P. Si group consists of Si and Al. Each textural zone is composed of three or four elemental groups. These four elemental groups are correlated with mineral composition, such as, Mn group with todorokite, Cu-Ni-Mg group with buserite, Fe group with Co-bearing iron-oxyhydroxide minerals, and Si group with silicates.

Jan 1, 2002

By Tetsuo Yamazaki

The Kuroko-type seafloor massive sulfides (SMS) in the western Pacific have received much attention as sources for economic recovery of gold (Au), silver (Ag), copper (Cu), zinc (Zn), and lead (Pb). Since the end of the 1980s, the Kuroko-type SMS have been found in the back-arc basins and on oceanic island-arc areas. In Okinawa Trough (Halbach et al., 1989) and on the Izu-Ogasawara Arc (Iizasa et al., 1999) are the typical representatives in the Japan’s EEZ. They yield a higher concentration in Au and Ag than the SMS found in ocean ridge areas (Rona, 1985). Similar formation processes with the Kuroko ore deposits on-land in Japan have been expected and outlined by many researchers (Sillitoe, 1982; Scott, 1985). The higher Au and Ag contents have increased the chances for profitable mining operation, which is under consideration by a private company (Malnic, 2001). Information about the resource potential of the targeted Kuroko-type SMS deposit, such as the amount of SMS ore body, the inside structure, the mean metal yields, and the geographical details are necessary for a technical and economic validation analysis for the development. The Sunrise Deposit of Myojin Knoll on Izu-Ogasawara Arc in the Japan’s EEZ is selected as a target for the technical and economic validation analysis. The relatively higher amount of information on its resource potential is the reason why the deposit is selected.

Sep 24, 2006

By C. H. Hobbs

A recently completed series of projects funded by the Commonwealth of Virginia and the U.S. Minerals Management Service was designed to assess the distribution of heavy minerals on the inner continental shelf adjacent to Virginia. These projects indicate that a suite of minerals of both strategic and economic interest is present. Analysis of several hundred grab and core samples shows that zircon, monazite, and titanium minerals (ilmenite, rutile, and leucoxene) occur in quantities that probably warrant further study by the mineral industry. Furthermore, side-scan sonography and shallow seismic profiles have provided information on the thickness and areal extent of the mineral-bearing sands. Possible development of the resource is enhanced by a potential use of offshore sand for beach nourishment. The results of the preliminary studies have been presented in open-file publications and oral reports in order that the mineral industry might have an up to date basis upon which to consider more exploratory work. Much of the effort south of the mouth of Chesapeake Bay was made in cooperation with and enhanced by an independent study of sand resources for beach nourishment and other needs. Preliminary review of the quantitative analyses of the heavy-mineral content of several hundred samples demonstrates that the distribution of high concentrations is non-uniform. From core data, the greatest abundances of some economic heavy minerals (ilmenite, rutile, leucoxene, monazite, and

Jan 1, 1988

By U. Schwarz-Schampera, C. Rühlemann, H. -R. Kudrass

Within 2006 BGR will conclude a contract with the UN International Seabed Authority (ISA) for the exploration of polymetallic nodules. The contract covers an area in the Pacific nodule belt between the Clarion and Clipperton fracture zones, that which is about 75.000 km2 in size at water depths between 4200 and 5000 m (see Fig. 1). Up to now, 7 consortia or state parties have acquired similar exploration “licenses” for polymetallic nodules in the central Pacific Ocean and the Indian Ocean. These licenses of the UN authority are required according to the UN convention on the law of the sea (UNCLOS) as the areas of interest are located outside of national EEZs. The “licenses” then reserve exclusive rights to the applicant for a time span of about 15 years.

Aug 24, 2006

By Irina A. Pulyaeva

Hydrogenetic Fe-Mn crusts play an important role in marine mineral-deposit research because of their widespread occurrence and high concentrations of valuable and rare metals. Most Fe-Mn crust deposits occur on the tens of thousands of seamounts found in the global ocean as well as on ridges and plateaus. Because of these circumstances, it is essential to clarify a number of outstanding issues with regard to Fe-Mn crust history and development, including controls on metal sources and concentrations. The first-order characteristics of Fe-Mn crusts as potential ore deposits include concentrations of metals (grade) and the thickness of crusts (tonnage), which vary depending on Fe-Mn crust structure and texture. Data on the structure, composition, age, and deposit characteristics will help define which factors are key for the creation of mineral accumulation and which combination of factors leads to the formation of potentially economic concentrations of metals. In this paper, we address the structure and characteristics of Fe-Mn crust stratigraphic sections collected from Central and Western Pacific seamounts. We describe the changes in mineralogical and chemical compositions of crust layers of different ages, the occurrence and regional distribution of these layers that correlate regionally, and reconstruct the paleoceanographic conditions that influenced crust growth.

Jan 1, 2010

By Hyung-woo Kim

This paper concerns about steering characteristics of pilot mining robot, named MineRo II, crawling on extremely cohesive soft soil using dynamic simulation software. The MineRo-II for deep-seabed manganese nodules, which aims at the use for pilot mining test, was manufactured in 1/5 scale of commercial mining capacity (see Fig. 1).

Sep 14, 2011

By Robert G. Ditchburn, Cornel E. J. de Ronde, Bernard J. Barry

The age of mineralization, its mode of formation, the time elapsed to amass an economic deposit, its capacity for sustainable extraction and, ultimately, its grade and tonnage, are key aspects in the economic viability of volcanic massive sulphide (VMS) deposits (Ditchburn et al, 2004). Radiometric dating methods applied at GNS Science have been recently refined with the purpose of efficiently determining the ages of seafloor VMS mineralization along active intraoceanic arcs. These developments include: determining the longevity of seafloor hydrothermal systems, details of individual chimney and massive sulfide mound growth, and insights into deep-seated processes, such as the transfer of elements from magmas to their overlying hydrothermal systems. In our pursuit to better understand seafloor hydrothermal systems along intraoceanic arcs, we have thus far compiled age information for three volcanic centres of the Kermadec arc (South Pacific) and one of the Mariana arc (NW Pacific).

By Makoto Yuasa, Akira Usui, Shipboard Scientists of SIP Cruises, Atsushi Suzuki, Shingo Kato, Kyoko Yamaoka, Akira Nishimura, Kiyo Kisimoto, Katsuhiko Suzuki

"We report here on current topics of our project, based on the results of recent cruises and laboratory analysis, about the diversity of compositions and configurations of the hydrogenetic ferromanganese deposits in several Northwestern Pacific Seamounts. This recent research has discovered important aspects of these deposits regarding the mode of variation with water depth, topography and substrate geology, possible bacterial mediation, temporal variation with age in mineralogy, and major and minor element chemistry. All cruises and analysis have been supported by the facilities and staff of the Japan Agency of Marine-Earth Science and Technology (JAMSTEC), Japan Oil, Gas, and Metal resources Corporation (JOGMEC), Geological Survey of Japan, and Kochi Core Center (KCC) using a remotely operated vehicle (ROV), a monitored rock drilling system, dredges, and manned-submersibles in the NW Pacific seamounts,The results indicate that most of the rock outcrops on the slopes, shoulders, and much of flat tops are covered with maximum 10-cm thick crusts, but the thickness, metal content, and microstructural properties are not always uniform over the seamounts, but variable in space and time. The micro-stratigraphic description of whole-rock samples indicates a history of deposition and sedimentation, which control the diversity in bulk composition and abundance caused by the variable incorporation of iron-manganese precipitates into the deposits during variable environmental conditions. We conclude that hydrogenetic precipitation of iron-manganese oxide has taken place for more than 20 million years at a growth rate about 4-6 mm/my, in water depths below 1000m. The results indicate a fairly continuous and constant metal deposition since the middle Miocene age or older to the present. Our case study of geological sciences at a model seamount within the Japanese EEZ suggests that scientific knowledge is useful and essential in exploring mineral deposits, economic estimation, and designing systems, if supported by well-combined geological and oceanographic and biological research. The distribution map of ferromanganese deposits and geological map will be published soon in 2017 to be issued by the Geological Survey of Japan."

Jan 1, 2017

By V. Soloviev

The world?s data available on near sea-bottom gas-hydrate accumulation and deep-water fluid-discharge areas are presented in this paper. Gas-hydrate accumulation associated with fluid discharge (mud volcanoes, gas seeps, gas-saturated water seeps) is characterized by the following. First, the largest hydrate accumulations in sediments are located at shallow subbottom depths and have well-defined limits, especially in the upper subbottom part. Second, gas-hydrate formation in fluid-discharge areas is a present-day process, with the global occurrence of deep-water fluid-discharge areas numbering up to about ten thousand, and with all the seep areas being favorable for the formation of near-sea-bottom gas-hydrate accumulation. Third and principal, gas resources in the hydrates can be considered as renewable. Estimates of possible gas volume in single accumulations of hydrates and the global budget, as well as possible methods of gas utilization from such gas-hydrate accumulations are discussed in the paper.

Jan 1, 2005

By V. Zaykov

The Urals massive sulfide deposits are concentrated in Silurian -Devonian fold belt extending for 1500 km with length from 50 to 150 km. By paleodynamic reconstmction it is established that they were formed in submarine parts of island arcs, in inter arc and back arc basins, marginal seas. When "black smokers" were found in rift zones of present oceans, problem searching their analogues in the Urals Paleozoic complexes was arisen. For solving this problem and demonstration of seafloor origin of massive sulfide many quarries and drill cores were carefully sketched and studied. Particular attention was given to correlation between ores and synchronous sedimentary rocks and fossils. Various laboratory methods were used for comparing sulfides from ore hills with ore-clastic sulfides.

Jan 1, 1993

By Alexander Malahoff

Mineral zonation studies were conducted on hydrothermal vents of two hot spot volcanoes. One study site is located within the Axial Caldera of the axial hot spot volcano of the Juan de Fuca Ridge. The young high-temperature hydrothermal vent field consisting of two polymetallic sulfide chimneys, five meters high, located at 130°01.5'W, 45°56.5'N, along a fault complex at the base of the southwestern wall of Axial Caldera was sampled during four ALVIN dives in 1983. Temperatures of up to 270°C were measured within the orifice of one of the chimneys, which was then broken off and recovered with the submersible. Both black and white "smoke" was observed to be emanating from the one chimney sampled. The high-temperature chimney extends directly from a field of broken lobate lavas which are located at a water depth of 1,550 meters, about 200 meters east of the caldera wall. The chimney makes one of the shallowest active high-temperature vents studied to date. The vent is surrounded by clumps of vestimentiferan worms and is located within an elongate field of red-colored iron smectite blankets and chimneys. The low-temperature field forms a ribbon 150 meters wide, extending for about 1,300 meters at the base of the wall. Chemical analyses of the hydrothermal deposits ranging from the polymetallic sulfides of the chimney to the outer zones of the low-temperature field show a range of elemental assemblages consistent with temperature zonation around the vent. Chemical zonation within the high-temperature

Jan 1, 1988