Search Documents

By D. S. Cronan

Mineral exploration problems in the S.W. Pacific are not unique to that region, but a combination of favourable circumstances render it an ideal area to attempt to solve such problems. The land area of the S.W. Pacific island nations is only a fraction of the total sea area they can claim under current International Law. Hence, they have a great need to explore and evaluate their offshore areas. For the past ten years the focus of this work has been CCOP/SOPAC which has individually and jointly with other groups initiated and maintained far reaching marine mineral exploration programmes. In association with CCOP/SOPAC the writer has obtained and analysed approximately 650 sediment samples from the S.W. Pacific region for seventeen elements. Multivariate statistical techniques have been applied to the data set. The aim has been to identify chemically anomalous sediments reflecting either sea floor mineralisation and/or mineralisation on adjacent land areas.

Jan 1, 1985

By RB. Pedersen, T. Barryere, E. Reeves, A. Stensland, I. Thorseth, T. Baumberger

Venting on ultraslow spreading ridges is far more abundant then previously predicted, and the discrepancy between observed and predicted vent field density may imply that non-magmatic heat sources are common along these ridges (Baker and German, 2004; Escartin et al., 2008; Rona et al., 2010; German et al., 2016). In this study we have estimated the flux from two hydrothermal vent sites situated on the slow to ultraslow spreading Mohns Ridge at the Arctic Mid-Ocean Ridge system (AMOR). The flux estimates have been made using the primordial isotope 3He in the non-buoyant plume above the Loki’s Castle vent field at the northern termination of the Mohns Ridge, and from the Jan Mayen vent fields area situated close to the southern termination of the ridge. Primordial 3He enters the oceans through degassing and mixing with hydrothermal fluids eventually to be discharged at the ocean floor primarily at hydrothermal vent sites and submarine volcanic eruptions (e.g. Clarke et al., 1969; Lupton and Craig, 1981; Lupton, 1998). Once introduced into the water column the concentration will only decrease by dilution due to its conservative behavior in the water column. Water column samples were collected using a CTD (conductivity, temperature, depth) probe (911plus Seabird) with a Niskin water bottle rosette. The water column above the Jan Mayen vent fields (JMVF) was sampled in the years 2006, 2011, 2012 and 2013 (82 samples) and the water column above the Loki’s Castle vent field was sampled in the years 2007, 2008 and 2009 (116 samples).

Jan 1, 2018

By Justin C. I. Baulch

In October 2004 Placer Dome entered into an exploration farm-in agreement with Nautilus Minerals, to explore for Submarine Massive Sulphide (SMS) deposits on Nautilus? PNG exploration tenements. Placer/Nautilus currently holds approximately 15,000 km2 of tenements in PNG waters, either granted or under application, covering all reported seafloor hydrothermal vent occurrences.

Jan 1, 2005

By Igor E. Mikhaltsev

The goal of investigation of the midwaters and of the bottom of the world - ocean versus technological possibilities. Manned vehicles and maximum depth decision. The methods of solving of the problem. The science and technology alloy. Mutual venture of Academy of Sciences of the USSR and, Rauma-Repola Oy of Finland. MIR-1 and MIR-2 - as twins. No reasons of copy "Sea Cliff" and "Nautilus". Six landmarks of specificity of "MIR"-type submersibles. The manned spheres and three ballast spheres are made of maraging steel; the electric power resource (100 kwh) and maximum underwater speed (5 knots) is two times more than of the analogous vehicles while the batteries are of NiFe type; the MIR submersibles have the seawater ballast (and trim) system which means practically unlimited vertical manoeuvrability ; and the weight in air is equal to "Nautilus" - 18,6 tons (in case of equal energy resource the weight of MIR-1 or MIR-2 would be 17 tons). Some remarks on standard life support (248 man-hours) safety systems and specificity of launch & recovery system.

Jan 1, 1988

By Mikhail D. Ageev

The paper concerns with some questions of Autonomous Underwater Vehicle (AUV) control system design, which allows a motion at rough undersea terrain. The AUV advantages reveal itself completely during exploration of such objects as seamounts and reefs area. These objects are characterized by steep slopes (30 degrees and above) and chaotic situated obstacles (rock debris, pinnacles, escarpments). Uses of other technical facilities for operating in such formations are difficult, dangerous or impossible. These regions take an interest due to the presence of iron-manganese crusts. Modern AUV can estimate density of mineral by means of still camera or video recorder. For this reason the vehicle has to move with the distance of 3-5 meters from seabed. Under such conditions micro- and mesorelief presents a considerable danger for AUV. The AUV can bypass underwater obstacles in the various ways. However, in any case AUV motion will be characterized by intensive maneuvering on various speeds (from 0 up to 1.5 m/s), circular change of tractive force vector and, hence, a circular flow about the hull. So, AUV is equipped with the propulsion system, which provides free modes of motion.

Jan 1, 2003

By Shinichi Takagawa

The deep sea hydrothermal deposits are one of the most prospecting resources, and various works to develop these mines are now underway. There are also various methods for the pre-site survey of the mines: acoustic survey, electro-magnetic survey, and others. However, as a precise method at the final survey, drilling/coring is indispensable to confirm the three-dimensional distribution and to grasp the dignity of the ores for the final decision of industrialization. This drilling/coring at the final survey is done at many points with distance of 15~25m between each point for on-land deposits. This means that 1km by 1km square area requires (1,000m/25m)2 ~ (1,000m/15m)2 = 1,600 ~ 4,500 holes. The drilling/coring depths will be around 30m or more for the hydrothermal deposits. This depth seems very shallow, but because the stratum is very brittle and is very difficult to core, the average core recovery ratio is around 50%, and 0% core recovery happens very often. Thus, the indispensable work of coring for grasping the dignity of ores is a very difficult work although the coring depth is shallow, and also the required number of holes is enormous. Conventional drilling/coring method on the ocean is to use drillship. However, the cost is very huge. Recently a new technique has come out which is to use remotely controlled drilling machine on seafloor. This machine seems to have a very good performance. However, it is reported that the available inclination of the seafloor where the machine sits on must be less than 15 degrees. The sea floor inclinations of active hydrothermal vents area are usually very steep and slopes of 45 degrees or more are prevailing and it seems very hard to carry out drilling/coring for the machine at these steep slopes, although it is impossible to mine the ore at these areas because the temperature is too high to work there. The inclination of the sea floor at the dead or paused hydrothermal vents area where ore recovery is possible may be not so steep, and the machine may work well. However, the required number of holes is still a very heavy burden. In order to solve these problems, the author proposes a new concept of drilling/coring system operated from a conventional research ship. This concept is still a desk plan, but the author wants to realize this system at any means.

Jan 1, 2011

By Jan M. Peter

Many of the Pb-Zn massive sulfide deposits of the Bathurst area in northern New Brunswick, Canada, are intimately associated with laterally continuous iron formation (IF) (Figure 1). This IF is a fossil laminated, exhalative, chemical sediment. Together, the IF and the Brunswick #12, Brunswick #6, and Austin Brook deposits (rightmost discontinuous horizon on Figure 1) are collectively referred to as the "Brunswick Belt". To date we have only studied the Brunswick Belt and have not examined the horizon along which the QSR, CNE and Flat Landing Brook deposits lie. The Bathurst area is underlain by the Tetagouche Group (Figure 2), a Cambro(?)-Ordovician sequence of metasedimentary and bimodal metavolcanic rocks that was intruded by mafic to felsic plutons and subsequently deformed during the Taconic Orogeny. The stratigraphic sequence consists of shales and greywackes that are overlain by carbonaceous shales and felsic volcanic and volcaniclastic rocks; these are in turn overlain by mafic volcanic and sedimentary rocks. The massive sulfide deposits and IF occur within the upper portions of the felsic volcanic rocks in close association with carbnaceous metasedimentary footwall rocks (Figure 2).

Jan 1, 1993

By V. M. Hamza

Analysis of ground and airborne radiometric measurements in the Saquarema region (Rio de Janeiro) provides new insights into the breakdown and transport of mineral aggregates containing monazites, under sub-tropical weathering conditions. The breakdown process, accompanied by loss of low-density clay fractions in weathered materials is considered responsible for the observed patterns in relative enrichment of thorium and uranium along the migration paths of radionuclides. The characteristic features of these patterns provide clues as to the time and distance scales associated with processes of weathering and erosion. It is also possible to determine approximate locations of concentrations of accessory minerals. In this context, we advance the hypothesis that large under-water monazite deposits may be present along the offshore sand banks, in the coastal region of the state of Rio de Janeiro.

Sep 14, 2011

By Timm Schoening, Greinert. Jens, Iason –. Zois Gazis

"Ferromanganese nodules are again of interest because of their high concentrations of Ni, Co, Cu as well as REE. With regards to an operational underwater mining industry, one of the main questions and important requests is to finding a method that can predict the abundance of nodules with high accuracy within reasonable time spans, without many requirements for ground truth data; and all these on an operational scale and ideally automated. In this regard, we present results of a study based on the combination of highresolution multibeam and optical data acquired by an AUV using specific machine learning techniques to reveal a detailed distribution of the Mn-nodules in correlation to the seafloor terrain. The accuracy of the method employed and results gained were validated and approved through comprehensive statistical analysis and by comparison to box-core data.Study AreaOur study area (AUV survey block G77) is located in the Clarion-Clipperton Zone (CCZ) (Eastern Central Pacific Ocean), an area that has been receiving international research and industrial attention for many years already (e.g. McKelvey et al., 1979; Bernhard and Blissenbach, 1988, von Stackelberg and Beiersdorf, 1991, Jeong et al. 1996). Block G77 covers an area of 9.5km2 in a depth between -4478m and -4536m. The area is characterised by gentle slopes 0-5° (0-3° in most of the area and only in the outer parts of the Block slopes can exceed 5°). The seafloor is characterised by moderate to low rugosity, the only exception being a small area in the eastern part, where sub-recent smallscale volcanic activity created 15 cone-shaped morphological features of up to 55m height and 150m width that are clustered in an area of 700 x 380m (Figure 1)."

Jan 1, 2017

By J. Robert Woolsey

This paper provides certain Southeastern coal-burning utilities with an economic strategy for complying with the sulfur dioxide emission standards set firth by the Clean Air Act Amendments of 1990. The strategy takes advantage of the occurrence of vast quantities of manganese nodules on the Blake Plateau offshore Georgia and the Carolinas, a commodity which as been proven to be a highly effective dry sorbent of sulfur dioxide. Using existing technology, manganese nodules could be mined and transported via barge directly to power plant sites, where they would be used as filter material for cleaning sulfur dioxide from the effluents of coal-fired power plants. Completely sulfated filter material could be treated for the extraction of by-product metals such as cobalt, copper, nickel, and manganese. The strategy may well be enhanced by the occurrence of ore grade phosphate rock in the same area of the Blake Plateau. This phosphate rock could be simultaneously mined to effect a reduction in production costs if it is found to be suitable for use as either a direct application fertilizer or as an acidulated superphosphate fertilizer. The manganese nodule-based strategy offers a retrofitting solution for existing power plants that would minimize the capital costs for compliance with the Clean Air Act Amendments and has the added advantage of providing a number of other metal or fertilizer by-products.

Jan 1, 1992

By Allan Spencer

In March 2007, Nautilus Minerals Inc. announced that they had commenced their 2007 exploration and development program with the mobilization of the Research Vessel Wave Mercury and the Survey Vessel Aquila onsite Papua New Guinea.

By Steven D. Scott

Several polymetallic sulfide deposits (copper, zinc, f lead, silver, f gold) presently exposed at the surface of the ocean floor are of sufficient size and apparent grade that they will someday be seriously considered as mineable resources. Responsible ocean mining may have some real environmental advantages over land mining, although they both share the same downstream problems caused by smelting and refining. The area of disturbance for an ocean mine would be much less than for an equivalent sized deposit on land around which considerable rock has to be excavated in order to get at the ore. Acid mine drainage, a very serious problem in land ming, would not be a concern in the alkaline and oxygen deficient environment of the deep ocean. There would undoubtedly be loss of habitat for some marine organisms but this could be minimized by mining deposits that are no longer hydrothermally active and therefore support little life. The risk of severe corrosion and thermal damage to the mining equipment at hydrothermally active sites would probably preclude their recovery in any event. The scientific community and environmental advocates should take advantage of the long lead time before ocean mining commences to insure that the environmental mistakes of the past, as encountered in some land mining, are not repeated. In order to fully understand and thereby mitigate the consequences of recovering seafloor sulfides, test mining of a small deposit using the German-designed high capacity television grab, preceded and followed by detailed observations of the mining site from a submersible, is proposed.

Jan 1, 1992

By Dennis Sánchez Mora, John Jamieson

INTRODUCTION Work by Humphris et al., (2002); Ondréas et al., (2009); Barreyre et al., (2012); and Escartín et al., (2015) has identified active and inactive hydrothermal sites along the Lucky Strike segment. The sites that contain the largest accumulation of known sulfides are located between the north and the southern zones (Figure 1), a vent site area that is referred to as the Main Lucky Strike hydrothermal field (Escartín et al., 2015). Hydrothermal fluid outflow has been linked to a shallow fault network (Barreyre et al., 2012). However, specific constraints on fault geometries have not been determined. Other off-axis sites at Lucky Strike, such as Capelinhos (high temperature vent), and Grunnus (inactive?), as well as a low temperature vent field (on-axis), Ewan, have been described by (Escartín et al., 2015). Given the spatial relationship between the Main Lucky Strike hydrothermal field (MLSHF), and the intersection of northern rift faults with the southern rift faults, a structural analysis of this area can provide insight into the fault controls on fluid flow that leads to hydrothermal venting and sulfide precipitation. METHODOLOGY Structural data (dip direction and dip) was determined using Leapfrog Geo 4.0 software. Bathymetric data was obtained from Escartín et al., (2015) and references therein. The bathymetry was imported into Leapfrog Geo (in UTM format) and, using the structural modelling tool, individual measurements with dip direction and dip data were collected with a focus on the northern volcanic rift and the southern central volcano (Figure 2a). All measurements were taken from what the authors consider as normal faults, and to aid the determination of individual measurements a “face dip” map was constructed, where the bathymetry is colored by slope angle (Figure 2b). All measurements are simultaneously plotted on a stereonet generated by the Leapfrog Geo Software. Data were divided into northern and southern, and western and eastern zones to determine the relationship between hydrothermal venting and the structural geometries at Lucky Strike (Figure 2c). Slip measurements for individual faults were determined along the dip of the fault with a measuring tool. Net slip, heave (horizontal displacement), and throw (vertical displacement) was calculated for each of the zones.

Jan 1, 2018

By Brenda J. Burd

A very extensive spatial and temporal database on benthic infauna and associated sediment metals has been collected for Island Copper Mine on Vancouver Island, B.C. Canada from 1969 (pre-discharge) to 1998 (3 years post-discharge). The tailings deposited as organically impoverished, copper-rich, clays, silts and sands distributed according to particle size, bottom turbidity currents and strong, vertically mixed tidal currents. In addition, a large deposition of coarser waste rock along the north shore of Rupert Inlet contributed substantial material in the shallower, near-field area.

Jan 1, 2001

By Leonhard Weixler, Peter Platzek

The Company Bauer Maschinen is very well known in the field of specialist foundation equipment. In the diaphragm wall market, we have experiences both in manufacturing and executing projects all over the world since 1984. We have a population of more than 300 units working all over the world in all climate and soil conditions. Especially for hard soil and rock conditions, we have developed several cutting tools and systems to optimize the performance, e. g. the “flipper tooth” Besides the execution of land based foundation projects, we have performed our firs offshore project with the trench cutter in 1994. Our task was to take samples out of the alluvial soil off the coast of Namibia in a water depth of max. 200 m. We converted a drill vessel and launched the cutter thru the moon pool. The samples had a cross section of 3,40 m² and a max. depth of 5 m. They were used to estimate the content of diamonds. The first time, we reached the seabed of the deep sea was together with our seafloor exploration rig MeBo, where we can take cores up to a length of 160 m in a maximum water depth of 4000 m. With our customer MARUM, we have done several expeditions since 2005. The last expedition took place in the Black Sea to explore gas hydrates.

Jan 1, 2018

By Raymond A. Binns

In this first sub-seafloor examination of an active hydrothermal system hosted by felsic volcanic rocks at a convergent plate margin, we drilled 13 holes altogether, achieving deep cored penetrations at two sites. Our aims were (1) to delineate the lateral and vertical variability in mineralisation and alteration patterns below the PACMANUS hydrothermal site near the 1650-1700 m-deep crest of Pual Ridge in the eastern Manus back-arc basin, so as to understand links between volcanological, structural and hydrothermal phenomena, and (2) to establish the nature and extent of microbial activity within the system. Technological innovations vital to success included our precise location of holes on small targets with drill-stem video, the use of a new hard-rock re-entry strategy, and deployment of casing with a new hammer drill. Other technical achievements were the first ODP application of an advanced diamond coring system, and the first direct comparison in a hardrock environment between structural images obtained by wireline methods and by logging-while-drilling (resistivity-at-bit).

Jan 1, 2002

By Youngtak Ko

The northeastern Pacific shows the highest nodule abundance among the oceans in the world, and thus has been drawing international attention for deep-sea manganese nodule development. The objectives of this study are to construct database using geostatistics and geographic information system (GIS), to quantify rating value using probability and statistical methods, to suggest suitable sites for manganese nodule development, and to verify results using three statistical approaches. The copper and nickel contents of the nodules were determined by chemical analysis. Factors related to slope, aspect, water depth, and topography were obtained from multi-beam echo sounding data. The transparent layer thickness was determined using a sub-bottom profiler. The probability method was used to calculate each factor's rating, and the layers for different factors were summed to produce the development potential index (DPI). Result maps were constructed for manganese nodules development. The distribution pattern of DPI showed to be controlled of nodule abundance and metal contents. Verification was performed by comparing the results with sampling data in three ways: success and prediction rate, linear regression, and test of independence.

Sep 14, 2011

By D. S. Cronan

Based on analogy with the Clarion-Clipperton zone, three main factors appear to influence the occurrence of potentially economic nodules in the study area, (i) elevated biological productivity, mainly above 50gCm-2y-l, (ii.) sea floor depth near or below the CCD, (iii) an absence of turbidite sedimentation. These conditions are fulfilled in parts of the following basins, where available data indicate that high grade and sometimes abundant nodules occur. i) The East Central Pacific Basin west of the Line Islands extending to the East Central Pacific Basin north and east of the Phoenix Islands ii) The West Central Pacific Basin west and northwest of the Phoenix Islands iii) The North Penrhyn Basin north of Penrhyn Island Notwithstanding the similarities between the environmental conditions under which potentially economic nodules occur in the Clarion-Clipperton zone and in the areas listed above, such similarities may relate only to present day conditions. During the possibly long periods of nodule formation, environmental conditions may have varied, and the deposits formed under conditions different from those prevailing at the present day. However, the fact that both present day conditions and the deposits in the two areas do show similarities suggests that applying the same genetic model to them has some validity. Possibly, any changes in environmental conditions during the period of formation of the deposits has been similar in both areas. Such uncertainties can only be resolved by a much fuller evaluation of the evolution of nodule deposits in both areas throughout recent geological time.

Jan 1, 1986

By Jayne Holden

Development of a deep-sea mining system is a new and interesting field of research. Commercial mining of the ocean floor for SMS deposits is yet to occur, and while exploration of the undersea has been undertaken by various research institutes exploitation of SMS deposits is yet to be investigated in detail. Industry has been stimulated by the potential development of economically viable deep-sea mining methods. The establishment of deep-sea mining production has also been encouraged by industry trends. These include the success of the oil and offshore diamond industries, scientific advances in computer modeling, technological advances in undersea exploratory equipment and further development of the Law of the Sea. This project also presents an opportunity to build on UNSW?s established reputation, positioning the Mining Research Centre as a leader in this specialized field of research. This project aims to form a greater understanding of the environmental conditions associated with SMS deposits, detailing the physical, biological and chemical characteristics of typical ocean floor sites from an environmental management perspective. With the aid of previous numerical models and disturbance experiments that have been conducted at various ocean floor sites worldwide, new virtual reality models will be developed to enable assessment of the environmental impact of the undersea mining process. These models will simulate seafloor systems prior to mining through various stages including particle distribution and sediment disturbance, to illustrate the impact of a number of proposed mining techniques. The model will allow users an interactive virtual experience of a potential SMS deposit site where hotspots can be identified and mining processes can be demonstrated. This initial baseline model will help to establish generic parameters, which can then be modified and tailored to simulate a wide range of deposit sites and differing mining processes. These models will be validated with the development of appropriate physical modelling.

Jan 1, 2002

By A. Ivanova

The continental shelves occupy a vast area of Russia and contain complexes of commercial placer minerals. Of prime importance are Cenozoic placers of valuable minerals including gold, cassiterite, diamonds, chromite, platinoids, and minerals of titanium, zirconium and rare earth elements, biogenic amber and fossil ivory (1). Commercial placer minerals are associated with shelf placer formation zones (SPFZ). These zones are located at junctions of marginal orogens and shelf troughs in morphostructures where upwarping, subsidence, and sign-variable neotectonic movements are not significant. The SPFZs are characterized by ancient buried leveling planes with mantles of waste, series of wave-cut aggradation terraces on land and beneath the sea, and drowned and buried stream valleys. The occurrence of mineral placers in the SPFZs was caused by endogenic mineralization and exogenic placer hosted formation. Concentrations of commercial biogenic minerals are associated with areas of burial of biogenic material (release of resins by plants and theriofauna thanatocoenoses) and with their transition zones. Since the Oligocene, alternations in marine transgression-regression have dominated the shelf areas. This has resulted in the formation of polygenic placers. Climatic conditions are of great importance: warm and humid climate in the Paleogene-Neogene changed to colder climates in the late Pliocene (polar type sedimentation; formation of permafrost strata and sea glaciation). These events are responsible for the regularity in placer formation during the Cenozoic in which the early Cenozoic (Eocene-Oligocene-Miocene) and late Cenozoic (late Pliocene-early Pleistocene and late Pleistocene-Holocene) epochs are prominent.

Jan 1, 2004