Search Documents

By Wolfgang G. Brunner

The closing of the gap in the European waterway- net is one of the big and challenging traffic projects following the German reunification. The water canals in the North German plain connect the Rhine river, the border between Germany and France, with the Oder, the German border river to Poland. As early as in the 30's of the 19th century the planning and construction of a ship- lift and a canal bridge started, in order to close this last big gap in the system between the Mittelland Canal and the Elbe- Havel Canal near Magdeburg. This main waterway connects the West of Germany, known for its coal mines and steel mills, with the capital Berlin, and from there it goes on into Poland. The building activities started in 1934 but came to a complete stop in 1942 because of the war. The communist government in East Germany was not interested in continuing this huge project, including the ship lock Rothensee, the canal bridge crossing the river Elbe, the former border river between West and East Germany, and the lock Hohenwarthe due to lack of political backing along with low construction capacity.

Jan 1, 2000

By Kodi Ranga Swamy, N. Sankar, M. Akhila

"Until recently, liquefaction-related studies concentrated on clean sands believing that only sands are susceptible to liquefaction. However, a few earthquakes like 1976 Tangshan earthquake, the 1989 Loma Prieta earthquake, the 1999 Kocaeli earthquake, the 2010 Chile earthquake, and the 2011 Christchurch earthquake, etc. showed that sand with fines could also liquefy. The research findings on liquefaction of silty soils are limited, and several structures constructed on such soil deposits are damaged during the past earthquakes. Some previous results of research on earthquake events show an increase of liquefaction resistance in silt soils with increase the fines content, but some report the opposite trend. This study presents the results based on undrained triaxial cyclic tests which were carried out on the fine sand with fines (0%, 10%, 20% and 40% fines). The samples were prepared at the required unit weight (Dr = 50%) and saturated by using back pressure and cell pressure increments. Each consolidated sample is subjected to cyclic loading with sinusoidal wave load form at a frequency of 1 Hz. The liquefaction resistance is evaluated in terms of cyclic stress ratio required to cause 100% pore pressure or 20% failure strain occur at 15 numbers of load cycles. Results are presented in forms of pore pressure build up and axial strain propagation plots. As the fines content increased, an increase in liquefaction potential was observed.INTRODUCTIONLiquefaction and related phenomenon have been responsible for tremendous amounts of damage all around the world. In general, the liquefaction may occur in fully saturated sands, silts and low plastic clays. When the saturated soil mass is subjected to seismic or dynamic loads, there is a sudden buildup of pore water within a short duration, and it could not dissipate which leads to reducing the effective shear strength of soil mass. In this state, the soil mass behaves like a liquid and causes large deformations, settlements, flow failures, etc. This phenomenon is called soil liquefaction. As a result, the ability of soil deposit to support the foundations of buildings, bridges, dams, etc. is reduced. Liquefiable soil also exerts a higher pressure on retaining walls.This lateral movement of soil could cause settlement of the retained soil. A sudden build-up of pore water pressure during quake also triggers landslides. Liquefaction damages of structures are commonly observed in low-lying areas near the rivers, lakes, and oceans."

Jan 1, 2017

By Wendy L. Mathieson

The Bonneville Power Administration (BPA) will build about 500 miles of new 500-kV transmission lines in the next 5 years. Many new lattice towers will be built in remote locations or in environmentally sensitive areas. Therefore, micropile foundations were designed that could be installed in remote areas, in variable subsurface conditions, and in a manner that would reduce excavation volumes and potential erosion concerns. Typical lattice tower foundation axial loads range between 75 and 1,500 kips (300 to 6,700 kilonewtons [kN]) per leg, with uplift loads being slightly less than compressive loads. Lateral loads range from 5 to 320 kips (20 to 1,400 kN) per leg. Full-scale axial and lateral load tests were conducted in geologically representative soil units during the micropile design for the 9-mile-long (14-kilometer [km]), Kangley-Echo Lake transmission line that extends through a protected watershed east of Seattle, Washington. Micropile foundations for single and double circuit suspension and dead end towers were designed using these load test data.

Jan 1, 2004

By Jeff Jackson, Paul Axtell, David Graham

The Montana Department of Transportation recently awarded a contract to construct a replacement bridge across the Clark Fork River in Heron, MT. Both abutments and both intermediate bridge bents were to be founded on 6-ft and 8-ft diameter, permanently cased drilled shafts with rock sockets, respectively. Two drilled shafts per substructure location were designed for a total of eight drilled shafts. The original design included 6-ft diameter drilled shafts at the abutments but the Contractor elected to submit a Value Engineering proposal that increased them to 8-ft diameter. On the basis of the subsurface exploration program, extremely challenging subsurface conditions were known to exist, including the potential presence of large boulders within the predominantly sand and gravel soil matrix. The successful bidder elected to use an oscillator to install the permanent casing to the top of bedrock, while simultaneously removing the spoils from inside the casing with a clam-grab. On seven of the eight shafts, this approach worked well. Unfortunately, on one of the shafts, the casing met refusal on one or more boulders encountered in the predominantly sand and gravel soil overburden. Following several attempts, and despite several variations of approaches, it was determined that the casing could not be advanced beyond the obstruction without unacceptable risks to the pile-supported temporary work trestle (i.e., loss of soil and reduction in pile capacity for the foundations supporting the work trestle). To mitigate the problematic drilled shaft, a unique solution was designed and successfully constructed. The solution involved the construction of seven 16-in diameter micropiles constructed within the confines of the obstructed casing. The micropiles were drilled to bedrock through the sand, gravel, and boulders and include rock sockets to satisfy axial design requirements. The micropile casing thickness, grade and grout strength were designed to provide adequate flexural strength as well as to satisfy other design requirements. Upon completion of the micropile installation, the upper portion of the drilled shaft above the boulders and within the permanent casing was constructed as usual. This paper discusses the difficult subsurface conditions at the site, the drilled shaft construction difficulties, and the design and construction of the micropile solution.

Jan 1, 2018

By Klaus Pöllath

The Netherlands RandstadRail project makes use of a large range of sophisticated geotechnical techniques to allow a shield driven tunnel to approach the central station of Rotterdam. This paper describes the construction of three deep excavation pits constructed with 1.2 m and 1.5 m thick diaphragm walls. Besides the presentation of the actual diaphragm wall activities special consideration is given to the break-in and break-out situations of the TBM into the deep excavations pits using sealing blocks and partly glass fibre reinforcement in the diaphragm walls.

Jan 1, 2006

By Li Tiemin

It is one of important tasks in research of vibratory pile driving to increase speed of pile driving and depth of pile driving -- this means to increase capability of penetrating hard layer. In general, vibratory pile driving hammer make pile be situated in vibratory situation to drive pile by means of weight of hammer and pile, but the depth of pile driving and capability of penetrating layer are limited by dead weight of hammer. This paper introduces a new kind of vibratory pile driving hammer which differs from general ham­mer. A set of pressing system is attached to hammer and pile driving frame. The pull of winch installed on frame passing guide pulleys bring downwards press to pile through absorbing system of hammer. The practice and comparison test have showed that the new hammer is faster in pile driving and bigger in capability of penetrating layer than general one. Now, the vibratory pile driving hammer with pressing device has been applied widely in China. RESUME: The vibratory pile driving hammer based on vibratory principle to design have applied wide­ly in foundation engineering in many countries over the world. In order to suit the needs of deep foundation, at present, how can quicken speed of pile driving and increase depth of pile driving have become even more value to many countries in the world. This paper introduces a kind of rapid vibratory pile driving hammer which can drive pile deeper and more faster comparing with common vibratory pile driving hammer. Therefore, a kind of simple and reliable method has been offered for rapid vibratory pile driving in deep foundation.

Jan 1, 1991

By T. Soejima

In recent years, there has been a tendency in the field of foundation piling works to utilize piles of greater bearing capacity in order to meet increasing height and weight of modern building as a means of saving of piling cost. To satisfy these requirement, a new technique for large diameter bell bottom cast-in-place piling has been developed utilizing multi-head reverse circulation drilling system.

Jan 1, 2010

By José L. M. Clemente, John R. Davie

"Abstract An extensive pre-production static and dynamic pile load testing program was conducted for a coal-fired power plant. The static load testing program included axial compression, uplift (tension), and lateral load tests. Three types of piles were tested: Monotube, closed-end pipe, and step-tapered. The load tests were used to (a) determine pile driveability characteristics for each pile, (b) verify pile load response behavior, and (c) provide data to support the selection of a cost-effective piled-foundation system for the plant. A recent publication (Clemente and Lewis, 2013) describes the compression load testing program, the interpretation of instrumentation measurement results, and pile selection criteria. This manuscript describes site subsurface and groundwater conditions and installation of probe piles for testing, focuses on the uplift and lateral load testing program, and provides a comparative interpretation of the load test results.INTRODUCTIONThe pre-production probe pile load testing program described here was conducted for a 202-megawatt, coal-fired power and steam generating (cogeneration) facility. A schematic layout of the main plant (power block area) is shown in Figure 1, which also includes the locations of clusters of preproduction probe piles and boreholes drilled near these clusters.The load testing program included 24 pre-production probe piles driven throughout the power block area. The probe piles were driven at locations T-1 through T-8, shown in Figure 1. Three types of piles were driven at each location: Monotube pile; closed end, straight shaft pipe pile; and step-tapered pile. At each location, the three piles were driven in a row with the pipe pile at the center, and the center-tocenter spacing between piles was equal to about 1.5 m (> 3.5 pile diameters for the largest pile). No pile cap was used to connect the three piles, and the three piles driven at locations T-1 through T-8 will be referred to as pile clusters. A complete suite of static load testing (compression, tension, and lateral) was performed on each individual pile at Cluster T-2 and on the step-tapered piles only at Cluster T-8, shown in Figure 1.Clemente and Lewis (2013) provide details of the compression load testing program, the interpretation of instrumentation measurement results, and pile selection criteria. This manuscript focuses on the uplift (tension) and lateral load testing program. A brief summary of the site geology and existing subsurface and groundwater conditions in the vicinity of the test pile clusters is presented, with emphasis on T-2 and T-8. Probe pile driving results at T-2 and T-8 are also presented. Descriptions of the static uplift and lateral load test program at T-2 and T-8 are given along with a comparative evaluation of the load test results."

Jan 1, 2014

By M. B. Wechsler

An analysis is developed for determining the maximum loading, as well as the potential uplift of the piles on bridge pier foundations. There are considered piers supported on two through seven rows of piles, and related to two simply supported collinear superstructures of any structural material. The study leads to different types of influence lines for various load combinations. For load combinations containing vertical loads only, the related influence lines are similar to those as for the bending moments of a virtual span covering the two actual spans, as well as the gap between the two superstructures; and, in this case, the heavier loads should be positioned in the vicinity of the pier. While, in the case when vertical loads are acting together with hori­zontal forces, the related influence lines will indicate where the heavier live loads should be positioned. And they will also indicate on which portions of the spans the live load should be avoided.

Jan 1, 1989

By Walter I. Paniagua

A housing complex of 76 buildings is being constructed in the city of Morelia, in western central Mexico; the buildings are 5 levels high, with a shallow concrete slab foundation. Soil conditions include a soft clay stratum, with up to 8 m depth, in a highly seismic area. Pile foundations and micro-piles were considered, but discarded due to economic factors. The alternative of soil improvement with rigid inclusions was used. An FEM (Finite Element Method) analysis was conducted to determine the diameter, spacing, length and arrangement of the inclusions. Construction was implemented with traditional methods: soil boring, and mortar tremied with pipe and the aid of a sock to contain the material (no steel reinforcement was used). So far, 46 buildings have been built, and level measurements for 18 buildings have been recorded since 2006, with resulting good behavior in both total and differential settlements.

Jan 1, 2008

By Thomas C. Anderson

Thirty-four retaining walls are part of the $46 million upgrade of a 1942 depressed highway in Highland Park, Michigan near Detroit. This project will close a missing link between two newer roadways, I-75 and the John Lodge Freeway. The existing 75 ft. wide, six lane Davison Freeway is being replaced by a eight to ten lane, 200 ft. wide depressed highway in a limited right of way. The highway will be 20-25 ft. deep and 1.5 miles long. A design/build decision by the Michigan DOT saved about 37% of the engineers estimated cost of $19 million for the walls. The successful pre-qualified specialty contractor utilized an innovative solution for the walls consisting of tiedback/cantilevered walls on the north side and mechanically stabilized earth walls on the south side. All of the walls have an identical cast-in-place architectural facing.

Jan 1, 1999

By Paul W. Mayne

Axial pile performance can be rationally evaluated within an elastic continuum framework using field results from seismic piezocone tests (SCPTu). Adopting a versatile Randolph-type elastic pile model, the approach can be applied to either traditional top down loading using an anchored reaction beam or the newer Osterberg cell that simultaneously pushes the base and shaft in opposite directions. The axial load distribution within the shaft is also evaluated. For site-specific data at a given site, the SCPTu is an optimal means for collection of subsurface information because it combines penetrometer readings and downhole geophysics in one sounding. The results obtained are at opposite ends of the stress-strain-strength curves, specifically the peak strength for capacity interpretations and the small-strain stiffness (Emax) for evaluating the initial deformations. Axial pile capacity can be analyzed using both direct and indirect CPT methods. As such, the approach allows for a complete representation of the axial load-displacement-capacity curve for pile response. Case studies are presented for deep foundations situated in stiff clays at two national geotechnical test sites located in Houston and College Station, Texas, using top down loading, as well as a third case study of a drilled shaft in clay till loaded by O-cell in Alberta.

Jan 1, 2009

By Aaron S. Bradshaw, Ryan M. Coulson

The offshore wind industry in the United States is slowly emerging with the recent construction of the first offshore wind farm located off the coast of Rhode Island. The turbines at the Block Island wind farm are supported by piled jacket structures, which historically have been used for much heavier oil and gas platforms. Offshore wind turbines have unique design requirements and the axial behavior of the supporting piles under cyclic loading is important to design. Cyclic degradation along the pile shaft can affect the capacity, deformation, and stiffness performance of the foundation and of the structure as a whole. This paper proposes a strain-based approach to estimate the fatigue (or endurance) limit of a cyclically loaded pile that may be applicable to long-term service loading. The method is applied to an existing load test dataset and the analysis results appear consistent with the observed pile response. INTRODUCTION The demand for renewable energy has been increasing in recent decades and wind power has seen a dramatic increase in popularity. In Europe, as of 2017 there were 4,149 grid-connected offshore wind turbines across 11 countries (windeurope.org), many of which are supported on monopile foundations. It wasn’t until recently (2016) that the first offshore wind farm was constructed in the United States off the coast of Block Island, Rhode Island. The project included 5 piled jacket structures founded in terminal moraine deposits. Future offshore wind development along the U.S. eastern seaboard could possibly utilize jacket structures in granular foundation soils. Loads from wave, wind, and turbine rotation induce cyclic loads on the foundation that have on the order of 108 loading cycles over the service life on the structure (Schneider and Senders 2010). Turbines located along the U.S. east coast have the added risk of hurricanes. As shown in Figure 1a, the lateral loads on a jacket structure are transferred primarily as axial compressive and possibly tensile loads on the supporting piles depending on the weight of the structure. The friction along the shaft of the pile can be prone to cyclic degradation, leading to reduced pile capacity and stiffness, and increased deformations. An offshore wind turbine foundation must be designed for a variety of limit states including ultimate, serviceability, and fatigue limit states. For a jacket structure this would include an analysis of the ultimate axial pile capacity, axial stiffness, and axial deformations, all of which can be affected by cyclic loading both under extreme (i.e. storm) conditions as well as long-term service conditions. Axial pile stiffness is needed, for example, to estimate the natural frequencies of the structure as a whole and to assess dynamic and fatigue loads. The structure must be designed such that its natural frequency remains outside the loading frequencies of the waves and turbine blade passing frequencies to avoid resonance. Therefore, prediction of the axial response of the piles is important to the design of these structures.

Jan 1, 2018

By Kazuyuki Matsuzawa

A series of plate loading tests were carried out on a loam ground in order to investigate the influences of the plate size and the loading rate on the observed load-settlement relations. Two circular plates having diameters of 0.3 m and 1.0 m were used. Three types of loading methods were employed; 1) static cyclic maintained load test, 2) static continuous load test, and 3) rapid (dynamic) plate load test. An interpretation method called non-linear damping method was used to estimate a static load-settlement relation from the rapid plate load test signals. The derived static load-settlement relations match well with the measured results from the static load tests.

Jan 1, 2006

By Y. C. Han

The advances in seismic design considering soil-structure interaction or soil-pile-structure interaction are described using a substructure approach. The nonlinearity of soil is considered approximately using a boundary zone model with non-reflective interface, and computer programs are available for practical applications. The validation of model is confirmed with dynamic tests on piles in the field, and the results for a single pile are used to compare with the predictions in this study. The liquefaction for sand soil layer can be accounted for, and a case of liquefaction is discussed. Two practical examples are examined, a vacuum tower structure supported on foundation of steel pile group and a table top structure supported on foundation of concrete pile group. To illustrate the effects of soil-pile-structure interaction on the seismic response of vacuum structure, different base conditions are considered, rigid base, i.e. no deformation of the foundation; linear soil-pile system; and nonlinear soil-pile system. The method introduced can be applied to the design of tall buildings, bridges, industrial structures and offshore platforms with soil-pile-structure interaction under seismic or dynamic loads.

Jan 1, 2010

By Gordon Demetrick

3900 Yonge St. was not a typical site on which to build a condominium apartment. A steep hill covered the majority of the site. In order to use as much of this site as possible, the rear of the building was to have nine stores cut into the face of the hill. A permanent shoring system was required as the building structure was not designed to provide sufficient stabilizing elements to support the total earth pressure. The total excavation depth required was 36 m (120'-0") with the upper 12 m (40'-0") to be backsloped. The vertical face of soil to be supported was 24 m (80'-0'). The shoring system originally designed by the Structural Engineer was to support this face by installing soldier piles and inclined earth anchors. During bid preparation it became evident to us that the system as designed would be difficult and expensive to install due to wet soil conditions. An innovative design was required to overcome these problems. Anchor Shoring hired John Stephenson Consultants Ltd. to aid them in accomplishing this goal. After extensive investigation together with The Trow Group, a unique design was proposed which provided a practical solution to the shoring problem.

Jan 1, 1987

By Carole L. B. Mitchell

The increased use of micropiles and soil nailing presents a growing database of verification and sacrificial load test data. In Washington State, the use of micropiles is becoming common, and soil nails are now almost as widely used as tiebacks; yet the state of the practice in understanding load transfer rates has not improved. This research compiles load test data for micropiles and soil nails from Shannon & Wilson?s records in the Puget Sound region of Washington. Ultimate and maximum load transfer rates for design are correlated to geologic units and soil types found in the region. Variables such as pressure versus tremie grouting, hole diameter, soil density/consistency, and the presence of groundwater are compared to load transfer rates for similar geologic units and soil types. Results are also compared to published PTI, AASHTO, and FHWA guidelines. Our results indicate that published ranges may be conservative for some soil types in the Puget Sound region, especially for micropiles. Performing verification tests to failure instead of typical verification or performance tests is needed to improve correlations and provide less conservative design load transfer rates.

Jan 1, 2006

By R. D. Short

Environmental regulations for noise and air pollution are directly affecting the type of equipment and construction techniques being utilized for pile driving construction using diesel hammers in California and elsewhere. Consequently, the cost of construction is increasing and in some cases, the use of diesel pile hammers has been prohibited. Based on the trend in California and elsewhere in the world, environmental constraints are spreading and becoming more restrictive. The City of Tokyo, Japan, for example has banned the use of diesel hammers. Environmental restrictions on diesel hammers can be satisfied by using modern hammers, clean burning fuels, synthetic lubricants and pre-excavation techniques.

Jan 1, 1989

By Frederick C. Rhyner

Drilled shafts have become an economical foundation choice for bridges in the northeast United States, especially when they can be constructed over water without the use of cofferdams. For the Boscawen-Canterbury Bridge over the Merrimack River in New Hampshire, an unusual design was used to avoid the use of cofferdams and avoid the need for pier caps at the waterline. This design used a pair of integral drilled shaft ? columns to form a bent type of substructure for support. Drilled shafts were 8-foot diameter, about 90 feet deep, with 16-foot long rock sockets. These are integrally constructed with 6-foot diameter reinforced concrete columns extending 37 feet from the waterline to the superstructure. Design load cases focused on lateral loads from ice flows, stream flows, wind and seismic events. Alternative analyses using different methods were made to check the design results. This paper discusses the subsurface conditions, design of the drilled shafts and columns, rebar and joint detailing issues, and construction of the drilled shafts.

Jan 1, 2004

By Wolfgang G. Brunner

The closing of the gap in the European waterway- net is one of the big and challenging traffic projects following the German reunification. The water canals in the North German plain connect the Rhine river, the border between Germany and France, with the Oder, the German border river to Poland. As early as in the 30's of the 19th century the planning and construction of a ship- lift and a canal bridge started, in order to close this last big gap in the system between the Mittelland Canal and the Elbe- Havel Canal near Magdeburg. This main waterway connects the West of Germany, known for its coal mines and steel mills, with the capital Berlin, and from there it goes on into Poland. The building activities started in 1934 but came to a complete stop in 1942 because of the war. The communist government in East Germany was not interested in continuing this huge project, including the ship lock Rothensee, the canal bridge crossing the river Elbe, the former border river between West and East Germany, and the lock Hohenwarthe due to lack of political backing along with low construction capacity. Now this important project is in progress and this report describes the special foundation techniques used on the great ship lock Hohenwarthe. Hohenwarthe is a double- bay ship lock of considerable scale, which is notable for recirculating water rather than letting it flow. It includes 44 800 m2 ( 481 720 sq. ft) of up to 55 m ( 180 ft) deep cut- off walls, ground water control, 1248 bored piles with a depth of 22 m ( 72 ft ) serving as foundation and 28 000 m ( 91 864 ft) of soil densification with vibroflotation equipment for ground improvement. In the year 2003 the project shall be completed and all ships can travel from the West to the East through Germany without expensive and time- consuming detours through other canals and locks.

Jan 1, 2000